Next Article in Journal
Gate Control of Superconductivity in Mesoscopic All-Metallic Devices
Previous Article in Journal
Hot Sliding Wear of 88 wt.% TiB–Ti Composite from SHS Produced Powders
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Materials
Volume 14
Issue 5
10.3390/ma14051244
materials-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Energy Consumption and Environment Performance Analysis of Induction-Healed Asphalt Pavement by Life Cycle Assessment (LCA)

by
Qi Jiang
1,
Fusong Wang
1,2,
Quantao Liu
1,
Jun Xie
1 and
Shaopeng Wu
1,*
1
State Key Laboratory of Silicate Materials for Architectures, Wuhan University of Technology, Wuhan 430070, China
2
Department of Civil and Environmental Engineering, Norwegian University of Science and Technology, 7491 Trondheim, Norway
*
Author to whom correspondence should be addressed.
Materials 2021, 14(5), 1244; https://doi.org/10.3390/ma14051244
Submission received: 21 January 2021 / Revised: 24 February 2021 / Accepted: 26 February 2021 / Published: 5 March 2021
Browse Figures
Versions Notes

Abstract

:
In this paper, the sustainability of induced healing asphalt pavement is demonstrated by comparing the impact of asphalt pavement maintained by induced healing asphalt pavement technology and traditional maintenance methods (such as milling and overlaying). The functional unit selected is a 1-km lane with an analysis period of 20 years. The stages to be considered are material manufacturing, paving, maintenance, milling and demolition. Two case studies were analyzed to assess the impact of different technologies on the energy consumption and environmental performance of each maintenance alternative. By comparing the energy consumption and environmental emissions of the whole life cycle of pavement under the two technical conditions, the results show that the total energy consumption of traditional asphalt pavement is about 2.5 times that of induction-healed asphalt pavement, and the total greenhouse gas (GHG) emissions of the former are twice as much as that of the latter.

1. Introduction

In 2020, China’s fixed asset investment in highway transportation exceeded 2.2 trillion RMB [1]. By 2020, the total length of highways in China had reached 5.0125 million kilometers, an increase of 166,000 km over the previous year. The total length of roads maintained was 4.9531 million kilometers, accounting for 98.8% of the total highway length. One of the main reasons for the high amount of highway maintenance is that the current traffic presents the characteristics of large vehicle flow, large passenger volume and multi-channelization, which makes the asphalt pavement spall, crack, and creates potholes and other situations during the service period, and seriously affects the driving comfort of asphalt pavement [2,3]. In order to solve the problems caused by these situations, China mainly adopts the grouting joint, thin slurry sealing layer, micro surfacing and overlay maintenance measures [4]. However, it is difficult to diagnose the maintenance time of damaged pavement, so these pavement maintenance measures find it difficult to play a full role. Some of the pavement maintenance measures even cause traffic congestion, wastage of resources, high maintenance costs and environmental pollution due to the long maintenance time [5]. Therefore, it is urgent to study a new road maintenance technology in order to achieve the goal of fast and efficient road maintenance.
Electromagnetic induction (EMI) heating self-healing technology is a new efficient and fast maintenance measure for asphalt pavement. The concept of induction technology, originally developed by TU Delft, relies on conductive materials such as steel fibers, metal particles, and metal powders that can be inductively cured in asphalt mixtures [6]. The self-healing ability of asphalt concrete is highly dependent on temperature. When the temperature is too low, the penetration, diffusion and bonding of asphalt molecules between the fracture surfaces of asphalt concrete are weakened, leading to the difficulty of crack healing. However, with the increase in temperature, the infiltration, diffusion and bonding of asphalt molecules on the fracture surface is strengthened, which can significantly improve the healing rate of asphalt concrete. The self-healing technique of electromagnetic induction heating selectively heats the heat-induced materials such as steel fiber in asphalt mortar. The asphalt mortar containing steel fiber is heated up rapidly under the action of induction eddy current, which promotes the rapid healing of micro cracks, while the stone cannot be heated by induction heating. This local heating can not only ensure the healing of asphalt mortar cracks, but also avoid the damage to the pavement structure. Therefore, electromagnetic induction heating self-healing technology has a good application prospect [7].
In order to analyze the sustainability of induced healing techniques, life cycle assessments (LCA) were carried out according to ISO14040:2006 and 14044:2006 standards, which set out requirements and guidelines to be followed for proper analysis [8,9]. Life cycle assessment is a process to assess the environmental burden associated with a product, process or activity by identifying and quantifying the energy and materials used and wastes released to the environment, in order to assess the environmental impact of these energy and material uses and releases to the environment, and to identify and assess opportunities to affect environmental improvements. The assessment includes the entire life cycle of a product, process, or activity, including the extraction and processing of raw materials; manufacturing, transportation and distribution; use; reuse and maintenance; recycling and final disposal [10]. This methodology has previously been used to determine the environmental performance of pavements, principally comparing rigid and flexible layers [11,12], but has also investigated more innovative solutions, such as warm mixed asphalt or recycled materials [13,14,15]. However, there is little documentation of its use in the evaluation of induction-healing technology.
The purpose of this paper is to assess the energy consumption and greenhouse gas (GHG) emissions of different asphalt pavement maintenance technologies, to demonstrate the prospect of sustainable development of EMI heating self-healing technology. Since GHG emissions account for a major part of all air pollutants, and carbon dioxide is the main representative component of GHG, GHG are adopted as the main indicator of environmental impact in this paper [16]. Based on the test section project of self-repairing asphalt pavement, the life cycle of self-repairing asphalt pavement is divided into four stages: the material manufacturing stage, road construction and paving stage, road service maintenance stage and mixing mill recovery stage. According to the ISO 14040, the LCA method of shunt path analysis is used to assess the sustainability of self-repairing asphalt pavement by calculating the input of energy and resources and the output of air pollution in a separate process.
A LCA is commonly divided into four steps: goal and scope, inventory analysis, impact assessment and interpretation of the results. The interpretation of the results can compare the environmental impact of materials and identify the strengths and weaknesses of the assessment process. This, in turn, can be used as part of the research process to improve and update technology and enhance competitiveness.

2. Goal and Scope

The goal of this LCA is to demonstrate the sustainability of induction-healed asphalt mixtures developed in the test section project of self-repairing asphalt pavement by comparing the environmental impacts that this new technology produces with that of traditional mixtures repaired by milling and covering technology. Since the induction-healing technology was developed only for the upper pavement layer, the analysis focused on that layer, leaving the rest of the pavement unchanged.
For the analysis, a steel fiber asphalt concrete self-healing test section of Jiehui Expressway in Guangdong Province of China is taken as an example; a highway with three lanes per direction and gradation of GAC-16C asphalt mixture was selected. The functional unit is defined as a 1-km lane with a width of 3.75 m and an upper layer thickness of 0.045 m. An analysis period of 20 years is assumed.
The selection of the system boundaries is based on the stages defined in the standard EN 15804:2012 +A1:2003 [17,18]. However, in order to understand the integrity of the life cycle, the development and transportation of raw materials are considered as a separate module of the material manufacturing stage (Figure 1).

3. Life Cycle Inventory

This stage involves the creation of a consistent database by collecting and quantifying the inputs and outputs associated with the functional unit [12]. In this sense, data on resources consumed and emissions generated are compiled from different sources. Emissions from electricity production, fuel generation and combustion, and transportation (processes shared by all stages) were collected from the China Energy Statistical Yearbook (2018), Highway Life Cycle Energy Consumption Analysis and Energy Saving Strategy, and China’s localized LCA basic database [19,20,21,22]. In order to facilitate the calculation of energy consumption and GHG emissions at each stage of road construction in the life cycle, a list of major energy sources is listed, as shown in Table 1. The specific assumptions and data sources used to form the inventory for each stage are described next.

3.1. Material Manufacturing Stage

This stage includes resource consumption and GHG emissions from the development and transportation of the materials (asphalt, cement, coarse aggregate, mineral powder, fine aggregate, steel fiber). In addition to the raw materials of the traditional asphalt mixture, the key to the self-repairing asphalt pavement in this paper is the addition of steel fiber [16,23,24]. In the material manufacturing stage of raw materials, the production energy consumption and related emissions data of various materials are based on the existing database and relevant industrial environment and energy reports, while the transportation distance between the material manufacturer and the mixing station is recorded and converted to the calculated value according to the actual data of the project test section cases [25,26,27]. The upper layer production mix ratio of the test section is shown in Table 2, the production energy consumption and related emission data of various materials can be seen in Table 3, and the transportation distance is shown in Table 4.
Sources of raw materials used in the construction process of asphalt pavement are: asphalt produced in the Shell Styrene-butadiene-styrene (SBS) modified asphalt of Guangdong Yue Logistics Industrial Co., Ltd., Guangdong Province, China; aggregate with particle size of 3.5–22 mm is made from Shuangdong Furong Stone Farm; limestone fine aggregate and mineral powder with particle sizes of 0–2.36 mm are produced by self-processing; cement anti-spalling agent is produced by China Resources Cement Co., Ltd., Shenzhen, Guangdong Province, China; and conductive steel fiber is produced by Jiangsu Golden Torch Metal Products Co., Ltd., Jiangsu Province, China.
The production technology of self-repairing asphalt pavement is to add steel fiber with asphalt volume ratio of 6%, and increase asphalt dosage by 0.2% on the basis of the original mix ratio of ordinary asphalt concrete [28,29,30]. Considering the density difference between steel fiber and natural aggregate as well as binder, the proportion of added steel fiber and the later paving and rolling processes were optimized and adjusted accordingly.
According to the calculation of the existing production mix ratio in the project examples in the test section, the upper layer of 1 km traditional asphalt pavement needs 825.04 tons of coarse aggregate, 23.24 tons of cement, 290.51 tons of fine aggregate, 23.24 tons of mineral powder and 54.62 tons of asphalt. Accordingly, the 1 km self-repairing asphalt pavement needs 25.92 tons of steel fiber and 56.94 tons of asphalt.

3.2. Paving Stage

This stage includes three important processes: the preparation of asphalt mixture at the mixing station, the transportation of asphalt mixture to the paving site, and the paving and compaction of asphalt mixture. Compared to the traditional asphalt pavement construction, the self-repairing asphalt pavement is mixed with steel fiber, so the mixing time is 8 s longer than the conventional process requirements. Meanwhile, in order to ensure the compactness of the pavement, the workload of the paving and rolling process is increased.
The equipment selected for the mixing station is the forced intermittent asphalt mixture mixing equipment of Langfang Deji Machinery Technology Co., Ltd., Langfang, Hebei Province, China. The model is LB-4000 and the rated capacity is 320 t/h. In actual production, there is a big difference between the external mixing rate and the rated capacity [31,32]. Moreover, there will be quality loss of asphalt mixture in the actual construction process, so in the preparation process of the mixture, the actual quality of mixture is greater than the theoretical calculated quality, and the extra quality is controlled within 0.5%. Therefore, the actual energy consumption in the mixing stage is confirmed based on the parameters of rated capacity and the construction log records, as shown in Table 5.
In the transportation stage of the asphalt mixture, a dump truck is used to transport the mixture to the paving site. The single transport mass of the dump truck is 35 tons. Assuming that the mixing station is approximately 7 km from the paving site, according to the survey of the transport driver, the average consumption of diesel fuel per kilometer of is 2 L. Thus, 0.688 kg of diesel fuel is consumed of per ton of mixture transported.
In the paving and compacting stage of asphalt mixture, the main energy consumption is generated by the paver and rollers during the operation. Table 6 lists the main mechanical energy consumption in the paving stage of traditional asphalt pavement. The data in the table are from engineering log records and field mechanical driver surveys.

3.3. Maintenance Stage

Maintenance activities will depend on the mixture to be repaired as traditional asphalt mixtures will need to be replaced by rolling and covering techniques, and the induction-healed asphalt pavement will also be healed by induction-healing treatments [24,33,34]. Therefore, the impact of this stage is related to the two maintenance actions. The maintenance method of self-repairing asphalt pavement in this paper is to repair the pavement upper layer by electromagnetic induction heating by the maintenance vehicle, and the energy consumption is mainly generated by the electric energy consumed by the maintenance vehicle. Traditional asphalt pavement maintenance includes the impacts associated with the milling of the old asphalt layer, transportation to the recovery center, the production of materials, transportation to the roadworks and construction of new asphalt layer.
In order to determine the maintenance schedule (Table 7), it is necessary to stipulate the usual design life of traditional asphalt pavement. According to many previous experiences of construction enterprise, this can be estimated to be 15 years, while the design life of self-repairing asphalt pavement is 20 years [35,36].
During maintenance work, the power of the maintenance vehicle is 155 kW, the driving speed is 1.2 m/min, and the healing width is 5 m. Under this condition, the maintenance vehicle can raise the temperature of the upper layer of the road from the ambient temperature to the optimal healing temperature of 120 ℃ [37,38,39,40]. Therefore, the single maintenance of the 1 km asphalt pavement test section requires the maintenance vehicle to run twice and consumes 4305.56 kW·h of electric energy. The energy consumption of self-repairing asphalt pavement is 25,833.36 kW·h during the maintenance stage of its design life.
For the mill and overlay activities, according to the maintenance schedule of an overhaul in the seventh year and the twelfth year, respectively, the energy consumption at this stage mainly considers the materials and construction machinery involved in the overhaul. It is assumed that 50% reclaimed asphalt pavement (RAP) is used in the material manufacturing stage. Therefore, it is two processes of milling and overlaying for the overhaul of traditional asphalt pavement.

3.4. Milling and Demolition Stage

According to the survey of the test section project cases, when the milling machine runs at full load on the asphalt pavement, the milling machine consumes 0.11 L of diesel fuel for 1 ton of asphalt concrete. Assuming a distance of 40 km between the maintenance section and the mixing station, a 15-ton dump trucks is usually used to transport the used abrasive material and the newly mixed asphalt mixture. According to Budget Amount of Highway Engineering and Quota of Cost of Highway Construction Machinery Platform Shift [41,42], the energy consumption and GHG emissions generated in this stage are shown in Table 8.

4. Life Cycle Impact Assessment

Once the inventory was completed, the resources consumed and GHG emissions were converted into impacts through an energy conversion method, which calculated the energy by converting the standard coal coefficient to the standard coal multiple [12,25,32]. The environmental impact of each stage can be divided into two parts: energy consumption and CO2 equivalent emissions.

4.1. Energy Consumption Impact Assessment

In the material manufacturing stage of raw materials, the energy consumption comparison between induction-healed pavement and traditional asphalt pavement is shown in Figure 2 and Figure 3. The pie chart shows the proportion of energy consumption in manufacturing and transportation for each material, and the bar chart shows the difference in the manufacturing and transportation energy consumption for each material. The energy consumption of induction-healed asphalt pavement at this stage is similar to that of traditional asphalt pavement, which are 51% and 49%, respectively. The production of asphalt is the most energy-intensive process in this stage, accounting for 67.28% and 67.29% in induction-healed asphalt pavement and conventional asphalt pavement, respectively.
In the road paving stage, the energy consumption of induction-healed asphalt pavement was compared with that of traditional asphalt pavement, and the results are shown in Figure 4. The calculation of energy consumption in this stage is divided into three processes: mixing of the mixture, transportation of the mixture and paving of the mixture. As can be seen from the figure, the energy consumption of the induction-healed asphalt pavement at this stage is significantly higher than that of the traditional asphalt pavement, and the energy consumption of the pavement with the two technologies is the highest in the process of mixing the mixture. The reason for this result is that the quality and density of the mixture increase when the steel fiber is added to the former, resulting in an additional 8 s adjustment time in the mixing process and an increase in the amount of transportation time [29,34,39]. On the other hand, natural gas is the largest of the three types of energy consumed in this stage. The main reason is that only natural gas is used for energy supply during the mixing process of the asphalt mixture in the mixing station. Therefore, it can be inferred that the energy consumption of the asphalt mixture in the mixing process is the highest.
The biggest advantage of induction-healed pavement is that a simple and quick maintenance method can be used in the maintenance stage and less energy consumption can be generated. Using the maintenance vehicle to generate an electromagnetic field, the upper layer of the steel fiber of asphalt pavement due is heated to electromagnetic induction, so that the asphalt temperature increases to enhance mobility and repair pavement distress. As shown in Figure 5, the energy consumption of two overhauls of traditional asphalt pavement and six EMI maintenance sessions of induction-healed asphalt pavement are compared. According to the information shown in the figure, within the design life of two asphalt pavements, the energy consumption of a single EMI maintenance session of the induction-healed pavement is 15,482.78 MJ, accounting for 1.4% of the single overhaul of traditional asphalt pavement; the energy consumption of two overhauls of traditional pavement is 2,167,166.40 MJ, the total energy consumption of six EMI maintenance accounts for 4.3% of this figure.
The design life of induction-healed asphalt pavement is 20 years, while the design life of traditional asphalt pavement is 15 years. According to the above pavement maintenance energy consumption, the average annual energy consumption of the two pavements can be obtained (Figure 6). The average annual energy consumption of induction-healed asphalt pavement is 3.2% of that of traditional pavement. It is obvious that the use of EMI maintenance technology can greatly reduce the energy consumption in the maintenance stage.
In the milling and demolition stage, the energy consumption is mainly generated in the transportation process of recycled materials. The addition of steel fibers to induction-healed asphalt pavement improves the quality and density of the asphalt mixture, resulting in greater energy consumption during milling and transportation (Figure 7).
Based on the energy consumption in the four stages, the pavement life cycle energy consumption is shown in Figure 8. It can be seen from the figure that the energy consumption of the traditional pavement is about 2.55 times that of induction-healed pavement. Among the four stages, the energy consumption of induction-healed pavement is the largest in the material manufacturing stage, while that of traditional pavement is the largest in the maintenance stage. Moreover, the former has a longer service life, so the induction-healed pavement has a more sustainable development prospect from the perspective of energy consumption analysis.

4.2. Greenhouse Gas Emission Impact Assessment

In the material manufacturing stage of raw materials, the GHG emissions comparison between induction-healed pavement and traditional asphalt pavement is shown in Figure 9 and Figure 10. The pie chart shows the proportion of GHG emissions in manufacturing and transportation for each material, and the bar chart shows the difference in the manufacturing and transportation GHG emissions for each material. Among all raw materials, asphalt is the largest source of GHG emissions. Meanwhile, the total emissions of the two asphalt pavements in this stage are similar, and the equivalent CO2 emissions sequence is: asphalt, cement, coarse aggregate, fine aggregate, steel fiber, mineral powder.
In the road paving stage, GHG emissions of the two asphalt pavements the are shown in Figure 11. Comparing the GHG emissions of the two types of asphalt pavement, natural gas produces the most GHG emissions, followed by electricity and diesel. The total emissions from induction-healed pavement are slightly higher than those from traditional pavement due to the addition of steel fiber to improve the quality and density of the mixture, as well as the adjustment of the mixing process.
Similar to the energy consumption in the maintenance stage, the equivalent CO2 emissions of the traditional pavement is still higher than that of the induction-healed pavement. As shown in Figure 12, GHG emissions from the former are 5.6 times that of the latter. During the service life of traditional pavement, the emissions generated by maintenance measures such as pre-maintenance, minor repair and medium repair of the maintenance stage are not taken into account, and the actual emissions generated by the former are much higher than those of the latter.
Figure 13 shows the total GHG emissions and the average annual GHG emissions of two asphalt pavement during their service life.
The average annual emissions from traditional pavement are 7.5 times those from induction-healed pavement. From the point of view of the maintenance stage, the environmental load of induction-healed pavement is much lower than that of traditional asphalt pavement. Moreover, under the same conditions, the former can realize the longer service life of asphalt pavement more quickly and conveniently. Therefore, induction-healed pavement should be a sustainable pavement technology.
Figure 14 shows the GHG emissions comparison between the two asphalt pavements’ milling and demolition stages. The GHG emissions from induction-healed pavement are slightly higher than those from traditional pavement due to the addition of steel fiber increasing the quality and density of mixture and consuming more fossil energy, thus increasing GHG emissions.
Based on the GHG emissions of the four stages, the GHG emissions of the pavement life cycle is shown in Figure 15. It can be seen from the figure that the GHG emissions from traditional pavement are about two times those of induction-healed pavement. This is mainly because, in the maintenance stage, the GHG emissions generated by two overhauls of traditional asphalt pavement are much higher than those generated by electromagnetic induction maintenance vehicles.

5. Conclusions

In this study, two different cases were used to compare induced healing with conventional milling and lay-up techniques to assess the sustainable development prospects of induced healing. The LCA method is used to divide the pavement life cycle into four stages: the material manufacturing stage, paving stage, maintenance stage, milling and demolition stage. The energy consumption and the GHG emissions in each stage were analyzed, respectively, and the following conclusions were drawn:
1. Among the two kinds of asphalt pavements’ service life, the energy consumption in raw material manufacturing stage of induction-healed asphalt pavement is the highest, while that of the maintenance stage of traditional asphalt pavement is the highest. Combined with the energy consumption of the four stages, the total energy consumption of the latter is about 2.5 times that of the former.
2. In the service life of the two kinds of asphalt pavement, the GHG emissions in the raw material manufacturing stage of induction-healed asphalt pavement is the highest, while that of the maintenance stage of traditional asphalt pavement is the highest. Combined with the GHG emissions of the four stages, the total GHG emissions of the latter are about two times those of the former.
3. In the maintenance stage, the single maintenance energy consumption of induction-healed pavement accounts for 1.4% of the single overhaul of traditional asphalt pavement. The energy consumption generated by the six EMI maintenance sessions of the former accounts for 4.3% of the two overhauls of the latter in its whole service life cycle.
4. In the maintenance stage, the GHG emissions from single maintenance of induction-healed pavement account for 5.9% of the single overhaul of traditional asphalt pavement. The GHG emissions generated by the six EMI maintenance sessions of the former account for 17.8% of the two overhauls in whole the service life cycle of the latter.
5. In the service life of the two kinds of asphalt pavement, the induction-healed pavement is more energy efficient and environmentally friendly than the traditional asphalt pavement. Moreover, under the same conditions, the induction healing technology can achieve longer service life of asphalt pavement faster and more easily. Therefore, induced healing pavement should be a sustainable pavement technology.
6. The methodology used for this study (converted to standard coal and using the LCA model) is likely to be implemented in future studies to obtain environmental emissions from different pavement maintenance methods.

Author Contributions

Conceptualization, Q.J., and S.W.; methodology, F.W.; software, F.W.; validation, Q.L., J.X. and S.W.; formal analysis, Q.J.; investigation, J.X.; resources, F.W., and Q.L.; data curation, Q.J.; writing—original draft preparation, Q.J.; writing—review and editing, Q.J.; visualization, J.X.; supervision, Q.L.; project administration, S.W.; funding acquisition, S.W. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the National Key R&D Program of China (2017YFE0111600) and the National Natural Science Foundation of China (51778515 and 7181101180), Technological Innovation Major Project of Hubei Province (2019AEE023) and Key R&D Program of Hubei Province (2020BCB064).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

The authors acknowledge Wuhan University of Technology for materials and experimental instrument support sincerely.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Ministry of Transport of the People’s Republic of China. Statistical Bulletin of Transport Industry Development in 2019; China Tunnel Construction: Guangzhou, China, 2020; Volume 40, p. 820. Available online: http://xxgk.mot.gov.cn/2020/jigou/zhghs/202006/t20200630_3321335.html (accessed on 3 March 2021).
  2. Guo, H.; Lian, J. Project teaching design and practice of roadbed and pavement maintenance technology course. J. Xi’an Univ. Arts Sci. (Soc. Sci. Ed.) 2015, 18, 114–116. [Google Scholar]
  3. Ruixin, W.W.L.; Ze, W. Asphalt Pavement Distress and Treatment of Western Mountainous Expressway. J. Chengdu Text. Coll. 2015, 32, 54–56. [Google Scholar]
  4. Juntao, W.S.L.; Quantao, L.; Jinxiang, H. Research on maintenance timing of functional premaintenance materials for asphalt pavement. China J. Highw. 2014, 27, 19–24. [Google Scholar]
  5. Chaoping, H. Study on Performance Prediction Model and Preventive and Protective Maintenance Measures of High Grade Asphalt Pavement; Chongqing Jiaotong University: Chongqing, China, 2015. [Google Scholar]
  6. García, Á.; Schlangen, E.; Van de Ven, M.; Liu, Q. Electrical conductivity of asphalt mortar containing conductive fibers and fillers. Constr. Build. Mater. 2009, 23, 3175–3181. [Google Scholar] [CrossRef]
  7. Venugopal, P.; Shekhar, A.; Visser, E.; Scheele, N.; Mouli, G.R.C.; Bauer, P.; Silvester, S. Roadway to self-healing highways with integrated wireless electric vehicle charging and sustainable energy harvesting technologies. Appl. Energy 2018, 212, 1226–1239. [Google Scholar] [CrossRef]
  8. Environmental Management. Life Cycle Assessment. Principles and Framework; (ISO 14040-2006); Deutsches Institut für Normung e.V. (DIN): Berlin, Germany, 2006; p. 44. [Google Scholar]
  9. Environmental Management. Product Life Cycle Assessment. Requirements and Guidelines; (ISO 14044:2006); Japanese Industrial Standards Committee (JISC): Tokyo, Japan, 2006; p. 84. [Google Scholar]
  10. Wang, C. Research on Environmental Analysis Methods in Environmental Materials; Sichuan University: Sichuan, China, 2007. [Google Scholar]
  11. Mazumder, M.; Sriraman, V.; Kim, H.H.; Lee, S.-J. Quantifying the environmental impacts of crack sealing and filling treatment in hot mix asphalt pavement. Innov. Infrastruct. Solut. 2018, 3, 61. [Google Scholar] [CrossRef]
  12. Moretti, L.; Mandrone, V.; D’Andrea, A.; Caro, S. Comparative “from Cradle to Gate” Life Cycle Assessments of Hot Mix Asphalt (HMA) Materials. Sustainability 2017, 9, 400. [Google Scholar] [CrossRef] [Green Version]
  13. Leng, Z.; Al-Qadi, I.L.; Cao, R. Life-cycle economic and environmental assessment of warm stone mastic asphalt. Transp. A Transp. Sci. 2018, 14, 562–575. [Google Scholar] [CrossRef]
  14. Puccini, M.; Leandri, P.; Tasca, A.L.; Pistonesi, L.; Losa, M. Improving the Environmental Sustainability of Low Noise Pavements: Comparative Life Cycle Assessment of Reclaimed Asphalt and Crumb Rubber Based Warm Mix Technologies. Coatings 2019, 9, 343. [Google Scholar] [CrossRef] [Green Version]
  15. Zaumanis, M.; Jansen, J.; Haritonovs, V.; Smirnovs, J. Development of Calculation Tool for Assessing the Energy Demand of Warm Mix Asphalt. Procedia Soc. Behav. Sci. 2012, 48, 163–172. [Google Scholar] [CrossRef] [Green Version]
  16. Lizasoain-Arteaga, E.; Indacoechea-Vega, I.; Pascual-Muñoz, P.; Castro-Fresno, D. Environmental impact assessment of induction-healed asphalt mixtures. J. Clean. Prod. 2019, 208, 1546–1556. [Google Scholar] [CrossRef]
  17. Sustainability of Construction Projects. Environmentally Sound Product Declaration. Core rules for product classification and building products. German, version EN15804-2012; Deutsches Institut für Normung e.V. (DIN): Berlin, Germany, 2012; p. 52. [Google Scholar]
  18. Durão, V.; Silvestre, J.D.; Mateus, R.; Brito, J.D. Assessment and communication of the environmental performance of construction products in Europe: Comparison between PEF and EN 15804 compliant EPD schemes. Resour. Conserv. Recycl. 2020, 156, 104703. [Google Scholar] [CrossRef] [Green Version]
  19. Available online: https://data.cnki.net/area/Yearbook/Single/N2019080025?z=D20 (accessed on 3 March 2021).
  20. Highway Life Cycle Energy Consumption Analysis and Energy Saving Strategy, 1984 ed; People’s Communications Press Co., Ltd.: Beijing, China, 2016.
  21. Chun, C. Research and Development of Network Database for Material Life Cycle Analysis; Beijing University of Technology: Beijing, China, 2009. [Google Scholar]
  22. Jingjing, Z. Research on Environmental Load Database and Green Development Evaluation System of Asphalt Mixture Production; Harbin Institute of Technology: Harbin, China, 2020. [Google Scholar]
  23. Li, H.; Yu, J.; Liu, Q.; Li, Y.; Wu, Y.; Xu, H.; Koshy, P. Induction Heating and Healing Behaviors of Asphalt Concretes Doped with Different Conductive Additives. Adv. Mater. Sci. Eng. 2019, 2019, 2190627. [Google Scholar] [CrossRef] [Green Version]
  24. Vo, H.V.; Park, D.-W.; Seo, J.-W.; Le, T.H.M. Effects of asphalt types and aging on healing performance of asphalt mixtures using induction heating method. J. Traffic Transp. Eng. (Engl. Ed.) 2020, 7, 227–236. [Google Scholar] [CrossRef]
  25. Porcelli, R.; Dotto, F.; Pezzolesi, L.; Marazza, D.; Greggio, N.; Righi, S. Comparative life cycle assessment of microalgae cultivation for non-energy purposes using different carbon dioxide sources. Sci. Total Environ. 2020, 721, 137714. [Google Scholar] [CrossRef]
  26. Ma, X.; Li, C.; Li, B. Carbon Emissions of China’s Cement Packaging: Life Cycle Assessment. Sustainability 2019, 11, 5554. [Google Scholar] [CrossRef] [Green Version]
  27. Huang, Y.; Qiao, Z.; Zhang, Y.; Zhang, H. Life-cycle assessment of carbon dioxide emissions of asphalt pavements in China. Proc. Inst. Civ. Eng. - Eng. Sustain. 2020, 173, 228–240. [Google Scholar] [CrossRef]
  28. Hosseinian, S.M.; Najafi Moghaddam Gilani, V.; Mehraban Joobani, P.; Arabani, M. Investigation of Moisture Sensitivity and Conductivity Properties of Inductive Asphalt Mixtures Containing Steel Wool Fiber. Adv. Civ. Eng. 2020, 2020, 8890814. [Google Scholar] [CrossRef]
  29. Yang, F.; Li, K.; Xiong, R.; Guan, B.; Zhao, H.; Pirri, C.F. Investigation on Deicing Property of Steel Wool Fiber-Reinforced Asphalt Mixture by Induction Heating. Adv. Mater. Sci. Eng. 2020, 2020, 5250628. [Google Scholar] [CrossRef] [Green Version]
  30. Xiong, R.; Jiang, W.; Li, K. Evaluation of deicing performance of steel velour fiber asphalt mixture based on induction heating. Sci. Technol. Eng. 2019, 19, 313–321. [Google Scholar]
  31. Li, B.Q.; Zhang, Q.H.; Wang, Y.J.; Chen, J.Y. Study on Factors Affecting Dust Removal Efficiency of Asphalt Mixing Plant. Key Eng. Mater. 2014, 599, 334–337. [Google Scholar]
  32. Qun, F.J. The daily management of asphalt mixing station and the effective methods of energy saving and consumption reduction are discussed. Eng. Constr. Des. 2019, 20, 218–219. [Google Scholar]
  33. Xu, H.; Wu, S.; Li, H.; Zhao, Y.; Lv, Y. Study on Recycling of Steel Slags Used as Coarse and Fine Aggregates in Induction Healing Asphalt Concretes. Materials 2020, 13, 889. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  34. Liu, Z.; Luo, S.; Wang, Y.; Chen, H. Induction Heating and Fatigue-Damage Induction Healing of Steel Fiber–Reinforced Asphalt Mixture. J. Mater. Civ. Eng. 2019, 31, 04019180. [Google Scholar] [CrossRef]
  35. Alber, S.; Schuck, B.; Wolfram, R.; Behnke, R.; Canon Falla, G.; Kaliske, M.; Leischner, S.; Wellner, F. Modeling of Surface Drainage During the Service Life of Asphalt Pavements Showing Long-term Rutting: A Modular Hydromechanical Approach. Adv. Mater. Sci. 2020. [Google Scholar] [CrossRef]
  36. Oyekanmi, O.J.; Ibe, C.C.; Ebiringa, O.T.; Ejem, E.A. Estimation of the Impact of the Overloaded Truck on the Service Life of Pavement Structures in Nigeria. Int. J. Traffic Transp. Eng. 2020, 9, 41–47. [Google Scholar]
  37. Hai, Z.J. Application research of microwave heating technology in asphalt pavement maintenance. China Highw. J. 2020, 24, 104–105. [Google Scholar]
  38. Bin, L. Research on Induction Heating and Healing Characteristics of Asphalt Concrete; Wuhan University of Technology: Wuhan, China, 2018. [Google Scholar]
  39. Yihan, S. Study on Self-Healing Characteristics of Asphalt and Asphalt Mixture; Wuhan University of Technology: Wuhan, China, 2017. [Google Scholar]
  40. Liang, Z.L.H.; Qing, T.; Yu, M.; Quantao, L. Study on the properties of induced heat self-healing for cracks of dense asphalt mixture. China Highw. J. 2017, 30, 17–24. [Google Scholar]
  41. Available online: https://max.book118.com/html/2019/0126/6014034010002004.shtm (accessed on 3 March 2021).
  42. Available online: https://max.book118.com/html/2019/0723/8116007072002036.shtm (accessed on 3 March 2021).
Materials 14 01244 g001 550
Figure 1. Life cycle assessment (LCA) boundaries.
Figure 1. Life cycle assessment (LCA) boundaries.
Materials 14 01244 g001
Materials 14 01244 g002 550
Figure 2. Energy consumption comparison between induction-healed pavement and traditional pavement in the material manufacturing stage.
Figure 2. Energy consumption comparison between induction-healed pavement and traditional pavement in the material manufacturing stage.
Materials 14 01244 g002
Materials 14 01244 g003 550
Figure 3. Fluctuation chart of energy consumption of the two asphalt pavements in the material manufacturing stage.
Figure 3. Fluctuation chart of energy consumption of the two asphalt pavements in the material manufacturing stage.
Materials 14 01244 g003
Materials 14 01244 g004 550
Figure 4. Energy consumption comparison of two asphalt pavement paving stages.
Figure 4. Energy consumption comparison of two asphalt pavement paving stages.
Materials 14 01244 g004
Materials 14 01244 g005 550
Figure 5. Energy consumption of two overhauls of traditional pavement and six electromagnetic induction (EMI) maintenance sessions of induction-healed pavement.
Figure 5. Energy consumption of two overhauls of traditional pavement and six electromagnetic induction (EMI) maintenance sessions of induction-healed pavement.
Materials 14 01244 g005
Materials 14 01244 g006 550
Figure 6. Energy consumption comparison of two asphalt pavements’ maintenance in their design life.
Figure 6. Energy consumption comparison of two asphalt pavements’ maintenance in their design life.
Materials 14 01244 g006
Materials 14 01244 g007 550
Figure 7. Energy consumption comparison of two asphalt pavements’ milling and demolition stages.
Figure 7. Energy consumption comparison of two asphalt pavements’ milling and demolition stages.
Materials 14 01244 g007
Materials 14 01244 g008 550
Figure 8. Energy consumption comparison of two asphalt pavements in their whole life cycle.
Figure 8. Energy consumption comparison of two asphalt pavements in their whole life cycle.
Materials 14 01244 g008
Materials 14 01244 g009 550
Figure 9. Greenhouse gas emissions of two asphalt pavements in the material manufacturing stage.
Figure 9. Greenhouse gas emissions of two asphalt pavements in the material manufacturing stage.
Materials 14 01244 g009
Materials 14 01244 g010 550
Figure 10. Fluctuation chart of greenhouse gas emissions of two asphalt pavements in the material manufacturing stage.
Figure 10. Fluctuation chart of greenhouse gas emissions of two asphalt pavements in the material manufacturing stage.
Materials 14 01244 g010
Materials 14 01244 g011 550
Figure 11. Greenhouse gas emissions comparison of two asphalt pavements’ paving stages.
Figure 11. Greenhouse gas emissions comparison of two asphalt pavements’ paving stages.
Materials 14 01244 g011
Materials 14 01244 g012 550
Figure 12. Greenhouse gas emission of two overhauls of traditional pavement and six electromagnetic induction maintenance sessions of induction-healed pavement.
Figure 12. Greenhouse gas emission of two overhauls of traditional pavement and six electromagnetic induction maintenance sessions of induction-healed pavement.
Materials 14 01244 g012
Materials 14 01244 g013 550
Figure 13. Greenhouse gas emissions of two asphalt pavements’ maintenance in their design life.
Figure 13. Greenhouse gas emissions of two asphalt pavements’ maintenance in their design life.
Materials 14 01244 g013
Materials 14 01244 g014 550
Figure 14. Greenhouse gas emissions of two asphalt pavements’ in milling and demolition stages.
Figure 14. Greenhouse gas emissions of two asphalt pavements’ in milling and demolition stages.
Materials 14 01244 g014
Materials 14 01244 g015 550
Figure 15. Greenhouse gas emissions of two asphalt pavements in their whole life cycle.
Figure 15. Greenhouse gas emissions of two asphalt pavements in their whole life cycle.
Materials 14 01244 g015
Table
Table 1. Energy inventory involved in road construction.
Table 1. Energy inventory involved in road construction.
Energy TypesCoefficientHeat EnergyCO2 Emission Factor
Standard coal1.00029.270 MJ/kg2.782 kg/kg
Heavy oil1.42941.816 MJ/kg3.247 kg/kg
Gasoline1.47143.070 MJ/kg2.996 kg/kg
Diesel1.45742.652 MJ/kg3.171 kg/kg
Natural gas1.33038.929 MJ/kg2.695 kg/kg
Electricity0.123 kg/(kw·h)3.596 MJ/(kw·h)0.972 kg/(kw·h)
Table
Table 2. Production mix ratio of ordinary asphalt concrete pavement.
Table 2. Production mix ratio of ordinary asphalt concrete pavement.
TypeAggregateMineral PowderCementAsphalt
3.5–22 mm0–3.5 mm Asphalt–Aggregate Ratio
GAC-16C7125224.7/4.9
Table
Table 3. List of raw material production.
Table 3. List of raw material production.
Raw MaterialEnergy ConsumptionCO2 Emissions
MJ/tKg/t
Styrene-butadiene-styrene (SBS) modified asphaltMatrix asphalt4736.6273.1
SBS modifier4286.555.0
Modification processing961.2131.1
Total9984.3459.2
Portland cement3980.72377.06
Coarse aggregate108.599.02
Mineral powder329.5724.50
Fine aggregate145.1813.79
Steel fiber423.4150.33
Table
Table 4. Transportation list of raw materials.
Table 4. Transportation list of raw materials.
Raw MaterialDistanceSingle LoadFuel Consumptionsmakal
L/100 km (Diesel)		Energy ConsumptionCO2 Emissions
kmtFull LoadNo LoadMJ/tKg/t
Asphalt67.350383033.5732.496
Aggregate115.4100392928.7842.140
Cement210.7100392952.5553.907
Steel fiber84.5100392921.0771.567
Table
Table 5. Energy consumption in the preparation of asphalt mixture.
Table 5. Energy consumption in the preparation of asphalt mixture.
EnergyTraditional PavementInduction-Healed Pavement
MJ/t1220 t/kmMJ/t1250 t/km
Natural gas (kg)4.8025858.444.7935991.25
Electricity (kw·h)4.6195635.185.3566695.00
Table
Table 6. Machinery list of paving stage.
Table 6. Machinery list of paving stage.
ModelNumber of DevicesWorkload/daysmakal
(km)		Fuel Consumption/day (L, Diesel Fuel)Fuel Consumption/km (kg, Diesel Fuel)
PaverVogler 2100-2 L11.1200152.73
Double steel rollerDynapac CC620012250105
Single steel rollerCLG 620H2248.2540.53
Rubber rollerXP smakal303 K12.522073.92
Table
Table 7. Maintenance schedule.
Table 7. Maintenance schedule.
YearInduction-Healed PavementYear Traditional Pavement
0Initial construction0Initial construction
5Induction healing
8Induction healing7Mill and overlay
11Induction healing
13Induction healing12Mill and overlay
15Induction healing
17Induction healing
Table
Table 8. Energy consumption and greenhouse gas emission inventory in the structural demolition stage.
Table 8. Energy consumption and greenhouse gas emission inventory in the structural demolition stage.
DistanceSingle LoadFuel Consumption
L/100 km (Diesel)		Energy ConsumptionCO2 Emissions
kmtFull loadNo loadMJ/tKg/t
Dump Truck4015251842.063.13
Milling Planer 0.11 L/t4.030.30
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Jiang, Q.; Wang, F.; Liu, Q.; Xie, J.; Wu, S. Energy Consumption and Environment Performance Analysis of Induction-Healed Asphalt Pavement by Life Cycle Assessment (LCA). Materials 2021, 14, 1244. https://doi.org/10.3390/ma14051244

AMA Style

Jiang Q, Wang F, Liu Q, Xie J, Wu S. Energy Consumption and Environment Performance Analysis of Induction-Healed Asphalt Pavement by Life Cycle Assessment (LCA). Materials. 2021; 14(5):1244. https://doi.org/10.3390/ma14051244

Chicago/Turabian Style

Jiang, Qi, Fusong Wang, Quantao Liu, Jun Xie, and Shaopeng Wu. 2021. "Energy Consumption and Environment Performance Analysis of Induction-Healed Asphalt Pavement by Life Cycle Assessment (LCA)" Materials 14, no. 5: 1244. https://doi.org/10.3390/ma14051244

APA Style

Jiang, Q., Wang, F., Liu, Q., Xie, J., & Wu, S. (2021). Energy Consumption and Environment Performance Analysis of Induction-Healed Asphalt Pavement by Life Cycle Assessment (LCA). Materials, 14(5), 1244. https://doi.org/10.3390/ma14051244

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop