Next Article in Journal
Geodesic Hermite Spline Curve on Triangular Meshes
Next Article in Special Issue
The In-Plane-Two-Folders Symmetric a-Plane AlN Epitaxy on r-Plane Sapphire Substrate
Previous Article in Journal
Determining the Tiers of a Supply Chain Using Machine Learning Algorithms
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Symmetry
Volume 13
Issue 10
10.3390/sym13101935
symmetry-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Improving Optical and Electrical Properties of GaN Epitaxial Wafers and Enhancing Luminescent Properties of GaN-Based Light-Emitting-Diode with Excimer Laser Irradiation

by
Yijian Jiang
*,
Haoqi Tan
and
Yan Zhao
Institute of Laser Engineering, Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing 100124, China
*
Author to whom correspondence should be addressed.
Symmetry 2021, 13(10), 1935; https://doi.org/10.3390/sym13101935
Submission received: 15 September 2021 / Revised: 6 October 2021 / Accepted: 12 October 2021 / Published: 14 October 2021
(This article belongs to the Special Issue Chirality Applied in Spintronics, Ferroics and Light–Matter Interactions)
Browse Figures
Versions Notes

Abstract

:
The effect of KrF excimer laser irradiation on the optical and electrical properties of epitaxial wafers with a p-GaN surface were investigated at different laser energy densities and pulse numbers. The laser-irradiated samples were annealed in oxygen. The laser irradiation-induced changes in optical and electrical properties of GaN epitaxial wafers were examined using PL, I–V, XPS, SIMS, and Hall effect measurements. Experimental results show that under an appropriate laser-irradiated condition, optical and electrical properties of the samples were improved to different degrees. The samples which were annealed after laser irradiation have better electrical properties such as the hole concentration and sheet resistance than those without annealing. We hypothesize that the pulsed KrF excimer laser irradiation dissociates the Mg–H complexes and annealing treatment allows the hydrogen to diffuse out more completely under the oxygen atmosphere at a proper temperature, by which the crystalline symmetry of GaN is improved. Under appropriate laser conditions and O2-activated annealing, the light output of the laser-irradiated GaN-based LED sample is about 1.44 times that of a conventional LED at 20 mA. It is found that the wall-plug efficiency is 10% higher at 20 mA and the reverse leakage current is 80% lower at 5 V.

1. Introduction

GaN-based materials and devices play increasingly important roles in various industries areas due to their large band gaps and high saturation velocities [1]. They are applied in laser diodes, high-speed transistors, and light-emitting diodes (LEDs) [2]. In general, Mg is the only effective acceptor in GaN that can become p-GaN that generates a hole conduction reliably [3,4]. Unfortunately, in the case of Mg-doped p-GaN, grown by metal-organic chemical vapor deposition (MOCVD), the p-GaN layer is highly resistive because the Mg acceptors are passivated by hydrogen to form electrically inactive Mg–H complexes [5,6,7]. As a consequence, an additional post-growth surface treatment is necessary to activate Mg acceptors to enhance the electrical and optical properties of GaN epitaxial wafers [8]. So far there are several methods to activate Mg acceptors and generate more holes including laser irradiation, thermal annealing under nitrogen atmosphere, low-energy electron beam irradiation, and microwave treatment [9,10,11].
It has been found that after laser irradiation, some physical properties, such as dielectric [12], electrical conductivity [13], luminescence [14,15], piezoelectric [16], and hydrophobic properties [17] can be improved in some thin films, crystals, ceramics, or polymers.
To date, excimer laser irradiation has been considered one of the most effective methods to activate Mg acceptors and improve the GaN epitaxial wafers electrical properties due to its many potential advantages such as high speed, less pollution, and selective area processes [4,18]. Lin et al. [3] have indicated that for the activation of the Mg-doped GaN layers irradiated by 248 nm laser, the dissociation of the Mg–H complexes and the formation of hydrogenated Ga vacancies (i.e., VGaH2) and/or the Ga vacancies occupied by interstitial Mg during the laser irradiation process led to an increasing of hole concentration. Oh et al. [19] have reported the 248 nm laser-irradiation effect on the electrical properties of no alloyed Ni/Au contacts on p-GaN and the samples that were laser-irradiated in N2 ambient produce higher sheet carrier concentrations and lower sheet resistances as compared with those of the as-grown samples. To further improve the GaN epitaxial wafer electrical properties, however, little previous work contains annealing treatment with appreciate atmosphere and temperature after laser irradiation. It is well known that excellent optical and electrical properties in GaN wafers are helpful for enhancing the light emission of LEDs [20]. However, previous research only focused on the connection between the laser irradiation effect and improving the basic optical and electrical properties in the p-GaN layer. There was no report on the luminescent performance of LEDs following the laser treatment.
In this study, we performed a pulsed KrF excimer laser irradiation on GaN epitaxial wafers followed by annealing in O2 with an appropriate temperature. The changes of optical and electrical properties of GaN epitaxial wafers with the two-step treatment were examined with Photoluminescence (PL), X-ray Photoelectron Spectroscopy (XPS), Hall treatment test, ohmic contact current–voltage (I–V) characteristics, and Secondary-Ion-Mass Spectroscopy (SIMS). Furthermore, the electrical properties of related LEDs were investigated through light output power-energy density and current-energy density measurements to inquire about the effect of the O2-annealed treatment after laser irradiation.

2. Experimental

The GaN epitaxial wafers purchased from Veeco® Company were grown on c-face (0001) sapphire substrates using a metal-organic chemical vapor deposition system. Trimethyl gallium (TMGa), ammonia (NH3), and bis (cyclopentadienyl) magnesium (Cp2Mg) were used as the metal-organic precursors for Ga, N, and Mg, respectively. The 430 μm thick sapphire substrates were deposited with a 30 nm GaN buffer layer, a 1.6 μm undoped GaN layer, and a 2 μm n-GaN layer. The active region included twelve periods of 2 nm AlGaN quantum wells and 18 nm GaN barriers. A 20 nm electron blocking layer and a 130 nm p-GaN layer were grown on top of the active region. Before the laser irradiation, the as-grown samples, with a size of 1 × 1 cm2, were immersed in acetone, alcohol, and deionized water for 5 min of ultrasonic cleaning in each step.
The GaN epitaxial wafers were then irradiated by a pulsed KrF (248 nm) excimer laser in air under different energy densities and pulse numbers [13,14,15]. The KrF excimer laser has a pulse duration of 23 ns at a repetition rate of 3 Hz. A 248 nm laser beam homogenizer was used to maintain a uniform beam spot size of 1 × 1 cm2 [21]. After the laser irradiation, some of the irradiated samples were annealed for the purpose of generating holes at 500 °C in pure O2 ambient (O2-activated sample) for 6 min.
The PL was acquired at room temperature by a monochromator (Princeton Instruments Acton SP2750) with a 325 nm line of a He–Cd laser as the UV excitation source. The surface chemistry properties of samples before and after laser irradiation were analyzed by XPS (Axis Ultra XPS). Ni/Au (3 nm/3 nm) layers were then deposited on the epitaxial wafers by electron beam evaporation. The electrical properties of the samples were examined by Hall effect measurements using an HL5500 system. The I–V curve was measured using a Semiconductor Characterization System (Keithley 4200-SCS). In order to explore the changes of lighter elements (H, O) during the laser irradiation, SIMS (Cameca IMS-6f) was employed using an ion beam with a primary kinetic energy of 8 keV to show the principle of the test.
To fabricate the LEDs [22,23], a 240 nm ITO thin film was subsequently evaporated on the top of the sample surface by an electron beam evaporator as a transparent conducting layer. Then, a Cr/Au layer structure was deposited as n-type and p-type contact electrodes. Finally, the current and light-output characteristics of LEDs were measured under specific DC-bias conditions at room temperature.

3. Results and Discussion

Figure 1 shows the room temperature PL spectra of as-grown and after laser irradiation with specific laser energy density and pulse numbers. The KrF excimer laser irradiated the GaN epitaxial wafers samples with 90 pulses at a repetition rate of 3 Hz. The energy density of the laser was 400 mJ/cm2. The samples were also irradiated by an energy density of 500 mJ/cm2 and 600 mJ/cm2, respectively. We have also investigated the laser-irradiated samples with the same energy density but with different laser pulses. However, damage to the surface of the samples was evident, the PL peak intensity decreased when the sample was irradiated at a laser energy density of 500 mJ/cm2 or the laser pulse numbers of 100. Therefore, it will be necessary to determine the optimum laser energy density and laser pulse number, in order to effectively enhance p-type optical and electrical properties of GaN samples with no surface damage.
The inset shows more clearly the intrinsic peak of the PL spectra. It can be seen that the intrinsic peak and the defect peak display a redshift after laser irradiation and this behavior is usually attributed to carrier localization which is common in highly inhomogeneous semiconductor materials and the changing of defect type and content during the laser irradiation. It is also worth noting that the intensity of the PL peaks, including the intrinsic peak and the defect peak, increased about 50% more than the as-grown sample after the laser irradiation. It is well known that the increasing PL intensity is due to the recrystallization of the sample surface, by which the crystalline symmetry was improved significantly. This indicates that a proper energy density of 400 mJ/cm2 and 90 pulses could activate the Mg acceptor and enhance the optical and electrical properties of the GaN material without leading to any deterioration of the optical properties of the sample surface.
To further investigate the mechanisms of the sample surface during the laser irradiation, XPS was used to analyze the chemical composition of the surface of the GaN epitaxial wafers after laser irradiation at an energy density of 400 mJ/cm2 and pulse number of 90. In Figure 2a, the result of the Ga 2p XPS shows that the Ga-2p core-level peak shifts toward the lower-energy level side by 0.8 eV, compared with those untreated samples. It means that the shifts in the surface Fermi level toward the valence-band edge attributes to the increased hole concentration of the sample due to the laser irradiation of the p-GaN surface wafer layer. The results of the XPS also show that there is an oxygen signal before and after laser irradiation. Additionally, we believe that an interfacial oxide layer increases the barrier height for hole injection from metal to p-GaN films, which results in a detrimental effect for the Ohmic contacts to p-GaN films. Furthermore, the intensity of the GaO peak energy decreases compared to the untreated sample. As Table 1 shows, proper laser irradiation improves hole concentration and lowers sheet resistance.
Table 1 also shows that the carrier mobility did not change significantly during the laser irradiation. It is noted that carrier mobility is a critical electrical characteristic that reflects the quality of the sample’s lattice structure. Thus, one can hypothesize that due to the laser irradiation there is no damage to the sample’s lattice structure. To investigate the connection between the shifting Ga-2p core-level peak position and the corresponding electrical properties, Figure 2b shows the Ga2p XPS spectra under different irradiation conditions. We can conclude that the shifting peak position exists under all the irradiated conditions. However, at 120 pulses and 500 mJ/cm2, compared to the as-grown sample, the shifting extent is nearly 0.58 eV, which is the maximum among the irradiated samples. It is noteworthy that the results of the XPS analysis support the conclusion in Table 1.
Many previous studies have focused on the individual effect of laser irradiation or annealing treatment, respectively [24,25]. In order to compare ohmic contact properties for the laser-irradiated GaN epitaxial wafers and the annealed sample, we conducted I–V characteristic measurement. It is well known that I–V characteristics reflect the contact quality of the GaN epitaxial wafers and the electrode metal, and its quality directly affects the luminescent properties of the GaN-based LED devices. Figure 3 shows the I–V characteristics for a non-alloyed Ni–Au contact before and after laser irradiation and annealing with O2. We can see clearly that the I–V characteristics of a sample after irradiation have a rectifying behavior, but with the same forward voltage, the current is larger than the as-grown sample, indicating that an improvement in the sheet resistance and carrier concentration has occurred during the laser irradiation. Furthermore, the O2-annealed sample after laser irradiation and annealing shows a linear behavior, indicating that the sheet resistance is further reduced and the carrier concentration is further increased during the annealing treatment. We believe that good in ohmic contact was formed after the O2-annealing treatment. Table 1 also shows the electrical properties after the annealing treatment.
In order to further investigate the changes of element contents during the laser irradiation, the samples were detected by SIMS, which plays an important role in detecting lighter element contents near the sample surface [4]. As we all know, using MOCVD growth of GaN epitaxial wafers methods is inevitably uneven sample surface hydrogen content of the element. Since the hydrogen ion has a positive charge, the main coupling unstable compounds such as magnesium would be easily formed and a magnesium-doped p-type GaN by impurities. We know the Mg–H bond energy of about 1.5 eV, and the photon energy of the KrF excimer laser reaches 5 eV. After the laser irradiation the Mg–H bond acceptor Mg could be activated, so that an improvement in the electrical properties of the sample was achieved. From Figure 4a it can be seen that, after laser irradiation, the hydrogen near the surface was reduced compared with the sample before irradiation. Hydrogen can be seen in the vicinity of the depth, highlighting the role of laser irradiation to activate the surface acceptor. As we know, the degree of oxidation of the surface of epitaxial wafers can influence its electrical properties. From Figure 4b, one can see that after laser irradiation, a lower oxygen content was obtained compared to those before the irradiation, indicating that the laser irradiation had caused the release of surface oxide to improve the electrical properties of the sample.
In order to investigate the impact of laser irradiation on the GaN-based LED, I–V characteristics and output power with different energy densities were examined by a conventional technique to test semiconductor light-emitting devices. Figure 5 shows typical I–V characteristics of the laser-irradiated samples with different laser energy densities. It can be seen that the forward voltages at 20 mA decrease significantly when the energy density becomes larger. Based on a previous report [4], the decreased forward voltage of the irradiated sample may be attributed to the proper laser-irradiated energy that could activate acceptors without any irreversible damage during the irradiation. The secondary shaft of Figure 5 shows the reverse I–V characteristics of irradiated samples with different laser energy densities. It is well known that the reverse leakage current is an important criterion of good or bad quality for semiconductor devices. As the energy density increases, the reverse leakage current is measured to be 7.7 × 10−8 A at the bias of −5 V when the energy density is 600 mJ/cm2, being smaller than any other irradiated samples. This is considered to be due to the presence of more dislocations in InGaN/GaN MQWs and improvement in the quality of GaN-based LED devices.
To compare the luminescent properties of O2-annealed and only laser-irradiated samples, L–I characteristics were measured at an injection current of 20 mA. Figure 6 shows that the light output power of O2-annealed and only laser-irradiated LEDs at different laser energy densities during the irradiation. The O2-annealed samples show better performance at light output power at any laser energy density compared to the laser-irradiated samples. It is worth mentioning that under appropriate laser conditions with pulse numbers of 90 at an energy density of 400 mJ/cm2 and O2-activated annealing, the light output of the laser-irradiated GaN-based LED sample is about 1.44 times that of a conventional LED at 20 mA, and it is found that wall-plug efficiency is 10% higher at 20 mA, the reverse leakage current is 80% lower at 5 V. These results imply that annealing in O2 ambient is a necessary step to enhance the luminescent properties of GaN-based LED.

4. Conclusions

The optical and electrical properties of GaN epitaxial wafers and luminescent properties of a GaN-based LED which was irradiated by a pulsed KrF excimer laser in air followed by O2-annealing treatment were investigated. A hole concentration of 4.54 × 1018 cm−3 was obtained in samples that were irradiated by the excimer laser at an energy density of 500 mJ/cm2 with pulse numbers of 120, followed by O2-annealing treatment with 500 °C in pure O2 ambient for 6 min. In addition to this, an examination of PL, I–V, XPS, and SIMS as a function of laser energy density suggests that the Mg–H complexes are dissociated, and the hydrogens are removed from the sample as the result of laser irradiation and annealing treatment. Under appropriate laser conditions and O2-activated annealing, the light output of the laser-irradiated GaN-based LED sample is about 1.44 times that of a conventional LED at 20 mA. It is found that the wall plug efficiency is 10% higher at 20 mA and the reverse leakage current is 80% lower at 5 V. These results indicate that a pulsed KrF excimer laser irradiation followed by annealing treatment is effective in improving p-type optical and electrical properties and enhancing the luminescent properties of GaN-based LEDs.

Author Contributions

Conceptualization, Y.J.; methodology, Y.J.; validation, Y.Z.; formal analysis, H.T.; investigation, H.T.; data curation, H.T.; writing—original draft preparation, Y.J.; writing—review and editing, Y.J.; visualization, H.T.; supervision, Y.J.; project administration, Y.J.; funding acquisition, Y.J. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the National Science Foundation of China, grant number 10974009, and the Major B Program of Beijing Natural Science of Education, grant number JC101311201201.

Data Availability Statement

The data presented in this study are available from the corresponding author.

Acknowledgments

The authors thank Chen Xu (Beijing University of Technology) for GaN-based LED fabrication and MA-tek for SIMS measurement.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Dupuis, R.D.; Krames, M.R. History, development, and applications of high-brightness visible light-emitting diodes. J. Lightwave Technol. 2008, 26, 1154–1171. [Google Scholar] [CrossRef]
  2. Vurgaftman, I.; Meyer, J.R.; Ram-Mohan, L.R. Band parameters for III-V compound semiconductors and their alloys. J. Appl. Phys. 2001, 89, 5815–5875. [Google Scholar] [CrossRef] [Green Version]
  3. Lin, Y.J.; Liu, W.F.; Lee, C.T. Excimer-laser-induced activation of Mg-doped GaN layers. Appl. Phys. Lett. 2004, 84, 2515–2517. [Google Scholar] [CrossRef] [Green Version]
  4. Oh, M.S.; Hwang, D.K.; Lim, J.H.; Kang, C.G.; Park, S.J. Low resistance nonalloyed Ni/Au Ohmic contacts to p-GaN irradiated by KrF excimer laser. Appl. Phys. Lett. 2006, 89, 042107. [Google Scholar] [CrossRef]
  5. Reshchikov, M.A.; Morkoc, H. Luminescence properties of defects in GaN. J. Appl. Phys. 2005, 97, 061301. [Google Scholar] [CrossRef]
  6. Rhode, S.K.; Horton, M.K.; Kappers, M.J.; Zhang, S.; Humphreys, C.J.; Dusane, R.O.; Sahonta, S.L.; Moram, M.A. Mg Doping Affects Dislocation Core Structures in GaN. Phys. Rev. Lett. 2013, 111, 025502. [Google Scholar] [CrossRef] [PubMed]
  7. Neugebauer, J.; VandeWalle, C.G. Role of hydrogen in doping of GaN. Appl. Phys. Lett. 1996, 68, 1829–1831. [Google Scholar] [CrossRef] [Green Version]
  8. Wang, G.H.; Wong, T.C.; Wang, X.C.; Zheng, H.Y.; Chan, T.K.; Osipowicz, T.; Foo, Y.L.; Tripathy, S. Reduced Contact Resistance and improved surface morphology of Ohmic contacts on GaN employing KrF laser irradiation. Jpn. J. Appl. Phys. 2011, 50, 04DF06. [Google Scholar] [CrossRef]
  9. Huang, B.R.; Chou, C.H.; Ke, W.C.; Chou, Y.L.; Tsai, C.L.; Wu, M.C. Effects of hydrogen treatment on ohmic contacts to p-type GaN films. Appl. Surf. Sci. 2011, 257, 7490–7493. [Google Scholar] [CrossRef]
  10. Jang, J.S.; Park, S.J.; Seong, T.Y. Ultrahigh transparency of Ni/Au Ohmic contacts to surface-treated p-type GaN. J. Appl. Phys. 2000, 88, 5490–5492. [Google Scholar] [CrossRef]
  11. Oh, M.; Lee, J.J.; Lee, J.K.; Kim, H. Electrical characteristics of Mg-doped p-GaN treated with the electrochemical potentiostatic activation method. J. Alloys Compd. 2014, 585, 414–417. [Google Scholar] [CrossRef]
  12. Ji, L.F.; Jiang, Y.J.; Wang, W.; Yu, Z.L. Enhancement of the dielectric permittivity of Ta2O5 ceramics by CO2 laser irradiation. Appl. Phys. Lett. 2004, 85, 1577–1579. [Google Scholar] [CrossRef]
  13. Ji, Y.L.; Jiang, Y.J. Increasing the electrical conductivity of Poly(vinylidene fluoride) by KrF excimer laser irradiation. Appl. Phys. Lett. 2006, 89, 221103. [Google Scholar] [CrossRef]
  14. Park, S.E.; Kim, D.J.; Han, W.S.; Ban, S.I. Effect of excimer laser irradiation on polycrystalline GaN. J. Cryst. Growth 2003, 253, 208–211. [Google Scholar] [CrossRef]
  15. Zhao, Y.; Jiang, Y.J. Effect of KrF excimer laser irradiation on the properties of ZnO thin films. J. Appl. Phys. 2008, 103, 114903. [Google Scholar] [CrossRef]
  16. Du, X.Y.; Ji, L.F.; Jiang, Y.J. Dielectric and piezoelectric properties of CO2 laser sintered Sr1.86Ca0.14NaNb5O15 piezoelectric ceramic. Ferroelectrics 2010, 402, 163–167. [Google Scholar] [CrossRef]
  17. Liu, Y.; Wei, Q.; Jiang, Y.J.; Nie, Z.R. Increasing the hydrophobic property of poly (vinylidene fluoride) by KrF excimer laser irradiation. Appl. Phys. Lett. 2010, 96, 231109. [Google Scholar]
  18. Kim, D.J.; Kim, H.M.; Han, M.G.; Moon, Y.T.; Lee, S.; Park, S.J. Effects of KrF (248 nm) excimer laser irradiation on electrical and optical properties of GaN:Mg. J. Vac. Sci. Technol. B 2003, 21, 641–644. [Google Scholar] [CrossRef] [Green Version]
  19. Oh, M.S.; Jang, J.S.; Park, S.J.; Seong, T.Y. Electrical properties of nonalloyed Ni/Au ohmic contacts to laser-irradiated p-GaN. J. Mater. Sci. 2006, 17, 831–834. [Google Scholar] [CrossRef]
  20. Sun, L.; Weng, G.E.; Liang, M.M.; Ying, L.Y.; Lv, X.Q.; Zhang, J.Y.; Zhang, B.P. Influence of p-GaN annealing on the optical and electrical properties of InGaN/GaN MQW LEDs. Phys. E 2014, 60, 166–169. [Google Scholar] [CrossRef]
  21. Jin, Y.H.; Zhao, Y.; Jiang, Y.J. Microlens beam homogenizer for excimer laser processing. J. Laser Appl. 2016, 28, 022601. [Google Scholar] [CrossRef]
  22. Zhu, Y.X.; Xu, C.; Liang, T.; Da, X.L.; Zhang, J.M.; Chen, L.B.; Shen, G.D. Enhanced output of GaN-based light-emitting diodes with stripe-contact electrodes. Appl. Phys. Lett. 2006, 89, 081127. [Google Scholar] [CrossRef]
  23. Zhang, J.M.; Zou, D.S.; Xu, C.; Zhu, Y.X.; Liang, T.; Da, X.L.; Shen, G.D. High power and high reliability GaN/InGaN flip-chip light-emitting diodes. Chin. Phys. 2007, 16, 1135–1139. [Google Scholar]
  24. Kim, D.J.; Kim, H.M.; Han, M.G.; Moon, Y.T.; Lee, S.; Park, S.J. Activation of Mg acceptor in GaN: Mg with pulsed KrF (248 nm) excimer laser irradiation. Phys. Stat. Sol. B 2001, 228, 375–378. [Google Scholar] [CrossRef]
  25. Haider, M.B.; Al-Kuhaili, M.F.; Durrani, S.M.A.; Bakhtiari, I. Effect of annealing on the optical properties of GaN films grown by pulsed laser deposition. J. Mater. Sci. Technol. 2013, 29, 752–756. [Google Scholar] [CrossRef]
Symmetry 13 01935 g001 550
Figure 1. Room temperature PL spectra of GaN epitaxial wafers before and after laser irradiation.
Figure 1. Room temperature PL spectra of GaN epitaxial wafers before and after laser irradiation.
Symmetry 13 01935 g001
Symmetry 13 01935 g002 550
Figure 2. Ga 2p XPS spectra of the GaN epitaxial wafers before and after laser irradiation. (a) Deconvenlution of the peak, (b) with different laser energy densities.
Figure 2. Ga 2p XPS spectra of the GaN epitaxial wafers before and after laser irradiation. (a) Deconvenlution of the peak, (b) with different laser energy densities.
Symmetry 13 01935 g002
Symmetry 13 01935 g003 550
Figure 3. I–V characteristics of Ni/Au Ohmic contacts on the as-grown, laser-irradiated, and O2-annealed GaN epitaxial wafers.
Figure 3. I–V characteristics of Ni/Au Ohmic contacts on the as-grown, laser-irradiated, and O2-annealed GaN epitaxial wafers.
Symmetry 13 01935 g003
Symmetry 13 01935 g004 550
Figure 4. SIMS depth profiles of (a) hydrogen atoms and (b) oxygen atoms from the p-GaN surface before and after laser irradiation with specific energy density and pulse numbers.
Figure 4. SIMS depth profiles of (a) hydrogen atoms and (b) oxygen atoms from the p-GaN surface before and after laser irradiation with specific energy density and pulse numbers.
Symmetry 13 01935 g004
Symmetry 13 01935 g005 550
Figure 5. The forward voltage and reverse current characteristics of the laser-irradiated samples with different laser energy densities.
Figure 5. The forward voltage and reverse current characteristics of the laser-irradiated samples with different laser energy densities.
Symmetry 13 01935 g005
Symmetry 13 01935 g006 550
Figure 6. The light output power of the laser-irradiated samples with different laser energy densities.
Figure 6. The light output power of the laser-irradiated samples with different laser energy densities.
Symmetry 13 01935 g006
Table
Table 1. Hall treatment test of GaN epitaxial wafers before and after KrF excimer laser irradiation and the samples annealed in O2.
Table 1. Hall treatment test of GaN epitaxial wafers before and after KrF excimer laser irradiation and the samples annealed in O2.
Hall Concentration (cm−3)Sheet Resistance (ohm/sq)Carrier Mobility (cm2/V·s)
Before irradiation sample4.81 × 101715 k1.81
90 pulses, 400 mJ/cm2 sample8.32 × 10177.5 k1.51
120 pulses, 500 mJ/cm2 sample9.87 × 10177.1 k1.42
120 pulses, 500 mJ/cm2 sample
(after annealing in O2)		4.54 × 10186.7 k1.16
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Jiang, Y.; Tan, H.; Zhao, Y. Improving Optical and Electrical Properties of GaN Epitaxial Wafers and Enhancing Luminescent Properties of GaN-Based Light-Emitting-Diode with Excimer Laser Irradiation. Symmetry 2021, 13, 1935. https://doi.org/10.3390/sym13101935

AMA Style

Jiang Y, Tan H, Zhao Y. Improving Optical and Electrical Properties of GaN Epitaxial Wafers and Enhancing Luminescent Properties of GaN-Based Light-Emitting-Diode with Excimer Laser Irradiation. Symmetry. 2021; 13(10):1935. https://doi.org/10.3390/sym13101935

Chicago/Turabian Style

Jiang, Yijian, Haoqi Tan, and Yan Zhao. 2021. "Improving Optical and Electrical Properties of GaN Epitaxial Wafers and Enhancing Luminescent Properties of GaN-Based Light-Emitting-Diode with Excimer Laser Irradiation" Symmetry 13, no. 10: 1935. https://doi.org/10.3390/sym13101935

APA Style

Jiang, Y., Tan, H., & Zhao, Y. (2021). Improving Optical and Electrical Properties of GaN Epitaxial Wafers and Enhancing Luminescent Properties of GaN-Based Light-Emitting-Diode with Excimer Laser Irradiation. Symmetry, 13(10), 1935. https://doi.org/10.3390/sym13101935

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop