Aerospace

3 pages, 148 KiB

Open AccessEditorial

Guidance, Navigation, and Control for the Moon, Mars, and Beyond

by Marco Sagliano

Aerospace 2024, 11(10), 863; https://doi.org/10.3390/aerospace11100863 - 21 Oct 2024

Viewed by 692

The interdisciplinary field known as Guidance, Navigation, and Control (GNC) has been one of the key contributors to the tremendous advancements in space exploration since the inception of the Mercury and Apollo programs [...] Full article

(This article belongs to the Special Issue GNC for the Moon, Mars, and Beyond)

2 pages, 127 KiB

Open AccessEditorial

Human Behavior in Space Exploration Missions

by Vadim Gushin

Aerospace 2024, 11(10), 862; https://doi.org/10.3390/aerospace11100862 - 20 Oct 2024

Viewed by 534

Abstract

Fifty years of human space exploration have allowed space psychology as an applied area of science to take major steps forward [...] Full article

(This article belongs to the Special Issue Human Behaviors in Space Exploration Mission)

27 pages, 3282 KiB

Open AccessArticle

Joint Optimization of Cost and Scheduling for Urban Air Mobility Operation Based on Safety Concerns and Time-Varying Demand

by Yantao Wang, Jiashuai Li, Yujie Yuan and Chun Sing Lai

Aerospace 2024, 11(10), 861; https://doi.org/10.3390/aerospace11100861 - 20 Oct 2024

Viewed by 726

Abstract

As the value and importance of urban air mobility (UAM) are being recognized, there is growing attention towards UAM. To ensure that urban air traffic can serve passengers to the greatest extent while ensuring safety and generating revenue, there is an urgent need [...] Read more.

As the value and importance of urban air mobility (UAM) are being recognized, there is growing attention towards UAM. To ensure that urban air traffic can serve passengers to the greatest extent while ensuring safety and generating revenue, there is an urgent need for a transportation scheduling plan based on safety considerations. The region of Beijing–Tianjin–Hebei was selected as the case study in this research. A real-time demand transportation scheduling model for a single day was constructed, with the total service population and total cost as objective functions, and safety intervals, eVTOL performance, and passenger maximum waiting time as constraints. A Joint Optimization of Cost and Scheduling Particle Swarm Optimization (JOCS-PSO) algorithm was utilized to obtain the optimal solution. The optimal solution obtained in this study can serve 138,610,575 passengers during eVTOLs’ entire lifecycle (15 years) with a total cost of CNY 368.57 hundred million, with the cost of CNY 265.9 per passenger. Although it is higher than the driving cost, it saves 1–1.5 h and thus has high cost effectiveness during rush hours. Full article

(This article belongs to the Special Issue Future Airspace and Air Traffic Management Design)

► Show Figures

Figure 1

39 pages, 35650 KiB

Open AccessArticle

An Analysis of a Complete Aircraft Electrical Power System Simulation Based on a Constant Speed Constant Frequency Configuration

by Octavian Grigore-Müler

Aerospace 2024, 11(10), 860; https://doi.org/10.3390/aerospace11100860 - 18 Oct 2024

Viewed by 993

Abstract

Recent developments in aircraft electrical technology, such as the design and production of more electric aircraft (MEA) and major steps in the development of all-electric aircraft (AEA), have had a significant impact on aircraft’s electrical power systems (EPSs). However, the EPSs of the [...] Read more.

Recent developments in aircraft electrical technology, such as the design and production of more electric aircraft (MEA) and major steps in the development of all-electric aircraft (AEA), have had a significant impact on aircraft’s electrical power systems (EPSs). However, the EPSs of the latest aircraft produced by the main players in the market, Airbus with the Neo series and Boeing with the NG and MAX series are still completely traditional and based on the constant speed constant frequency (CSCF) configuration. For alternating current ones, the EPS is composed of the following: prime movers, namely the aircraft turbofan engine (TE); the electrical power source, i.e., the integrated drive generator (IDG); the command and control system, the generator control unit (GCU); the transmission and the system distribution system; the protection system, i.e., the CBs (circuit breakers); and the electrical loads. This paper presents the analysis of this system using the Simscape package from Simulink v 8.7, a MATLAB v 9.0 program, which is actually the development of some systems designed in two previous personal papers. For the first time in the literature, a complete MATLAB modelled EPS system was presented, i.e., the aircraft turbofan engine model, driving the constant speed drive system (CSD) (model presented in the first reference as a standalone type and with different parameters), linked to the synchronous generator (SG) (model presented in second reference for lower power and rotational speed) in the so-called integrated drive generator (IDG) and electrical loads. Full article

(This article belongs to the Special Issue Electric Power Systems and Components for All-Electric Aircraft)

► Show Figures

Figure 1

25 pages, 7196 KiB

Open AccessArticle

Position Normalization of Propellant Grain Point Clouds

by Junchao Wang, Fengnian Tian, Renfu Li, Zhihui Li, Bin Zhang and Xuelong Si

Aerospace 2024, 11(10), 859; https://doi.org/10.3390/aerospace11100859 - 18 Oct 2024

Viewed by 427

Abstract

Point cloud data obtained from scanning propellant grains with 3D scanning equipment exhibit positional uncertainty in space, posing significant challenges for calculating the relevant parameters of the propellant grains. Therefore, it is essential to normalize the position of each propellant grain’s point cloud. [...] Read more.

Point cloud data obtained from scanning propellant grains with 3D scanning equipment exhibit positional uncertainty in space, posing significant challenges for calculating the relevant parameters of the propellant grains. Therefore, it is essential to normalize the position of each propellant grain’s point cloud. This paper proposes a normalization algorithm for propellant grain point clouds, consisting of two stages, coarse normalization and fine normalization, to achieve high-precision transformations of the point clouds. In the coarse normalization stage, a layer-by-layer feature points detection scheme based on k-dimensional trees (KD-tree) and k-means clustering (k-means) is designed to extract feature points from the propellant grain point cloud. In the fine normalization stage, a rotation angle compensation scheme is proposed to align the fitted symmetry axis of the propellant grain point cloud with the coordinate axes. Finally, comparative experiments with iterative closest point (ICP) and random sample consensus (RANSAC) validate the efficiency of the proposed normalization algorithm. Full article

(This article belongs to the Section Astronautics & Space Science)

► Show Figures

Figure 1

18 pages, 19399 KiB

Open AccessArticle

An Online Data-Driven Method for Accurate Detection of Thermal Updrafts Using SINDy

by Yufeng Lu, Chenglou Liu, Haichao Hong, Yunwei Huang, Tingwei Ji and Fangfang Xie

Aerospace 2024, 11(10), 858; https://doi.org/10.3390/aerospace11100858 - 18 Oct 2024

Viewed by 531

Abstract

Utilizing thermal updrafts shows potential for enabling long-endurance cruising of fixed-wing unmanned aerial vehicles without energy consumption. This article presents a novel online method based on sparse identification of nonlinear dynamics (SINDy) approach to achievement identification of thermal sources in the atmosphere. Initially, [...] Read more.

Utilizing thermal updrafts shows potential for enabling long-endurance cruising of fixed-wing unmanned aerial vehicles without energy consumption. This article presents a novel online method based on sparse identification of nonlinear dynamics (SINDy) approach to achievement identification of thermal sources in the atmosphere. Initially, the algorithm is incorporated into the upper-level planning system, interacting with the lower-level controller. Then, experiments are conducted through software-in-the-loop simulations (SITL) to validate the implementation of the proposed algorithm. It is found that direct observation of thermal sources through measurements using SINDy is unfeasible during straight and circular flight modes. Nevertheless, simulation analysis of the proposed approach indicates that under unobservable conditions, a portion of the parameters can still be identified. By comparing results obtained using the particle filter algorithm, this method is shown to accurately estimate the parameters with negligible errors under observability conditions. The novelty of this approach lies in its significant improvement of the localization accuracy of the thermal source, without the need for parameter adjustments in the algorithm. Finally, the proposed methods are integrated into commonly used hardware platforms, and their online feasibility is verified through hardware-in-the-loop simulations. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

21 pages, 12855 KiB

Open AccessArticle

Noise Study Auralization of an Open-Rotor Engine

by Qing Zhang, Siyi Jiang, Xiaojun Yang, Yongjia Xu and Maosheng Zhu

Aerospace 2024, 11(10), 857; https://doi.org/10.3390/aerospace11100857 - 17 Oct 2024

Viewed by 670

Abstract

Based on the performance and acoustic data files of reduced-size open-rotor engines in low-speed wind tunnels, the static sound pressure level was derived by converting the 1-foot lossless spectral density into sound-pressure-level data, the background noise was removed, and the results were corrected [...] Read more.

Based on the performance and acoustic data files of reduced-size open-rotor engines in low-speed wind tunnels, the static sound pressure level was derived by converting the 1-foot lossless spectral density into sound-pressure-level data, the background noise was removed, and the results were corrected according to the environmental parameters of the low-speed wind tunnels. In accordance with the requirements of Annex 16 of the Convention on International Civil Aviation Organization and Part 36 of the Civil Aviation Regulations of China on noise measurement procedures, the takeoff trajectory was physically modeled; the static noise source was mapped onto the takeoff trajectory to simulate the propagation process of the noise during takeoff; and the 24 one-third-octave center frequencies that corresponded to the SPL data were corrected for geometrical dispersion, atmospheric absorption, and Doppler effects, so that the takeoff noise could be corrected to represent a real environment. In addition, the audible processing of noise data with a 110° source pointing angle was achieved, which can be useful for enabling practical observers to analyze the noise characteristics. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

17 pages, 7439 KiB

Open AccessArticle

Effect of Temperature on Foreign Object Damage Characteristics and High Cycle Fatigue Performance of Nickel-Based Superalloy GH4169

by Li Sun, Xu Jia, Rong Jiang, Yingdong Song and Lei Zhu

Aerospace 2024, 11(10), 856; https://doi.org/10.3390/aerospace11100856 - 17 Oct 2024

Viewed by 559

Abstract

High-speed ballistic impact tests were conducted at room temperature and 500 °C on nickel-based superalloy GH4169 simulated blade specimens containing leading-edge features. The microscopic characteristics of the impact notch at room temperature versus 500 °C were observed by electron backscatter diffraction (EBSD), and [...] Read more.

High-speed ballistic impact tests were conducted at room temperature and 500 °C on nickel-based superalloy GH4169 simulated blade specimens containing leading-edge features. The microscopic characteristics of the impact notch at room temperature versus 500 °C were observed by electron backscatter diffraction (EBSD), and it was found that the grains on the notched subsurface were ruined, while in more distant regions, the impact energy was mainly absorbed by grain boundaries. Internal damage is more concentrated in the notched subsurface region at 500 °C compared to room temperature. The high cycle fatigue strength of the damaged specimens under different conditions was tested. The results showed that the high cycle fatigue strength of the damaged specimens increased with the increase in the notch depth, and the fatigue strength of the damaged specimens at 500 °C was higher than the fatigue strength at room temperature. Both the 48 h post-impact holding time at 500 °C and the preload during impact at 500 °C increased the fatigue strength of the damaged specimens. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

12 pages, 2926 KiB

Open AccessArticle

The Maintenance of Orbital States in a Floating Partial Space Elevator Using the Reinforcement Learning Method

by Weili Xu, Xuerong Yang and Gefei Shi

Aerospace 2024, 11(10), 855; https://doi.org/10.3390/aerospace11100855 - 16 Oct 2024

Viewed by 552

Abstract

A partial space elevator (PSE) is a multi-body tethered space system in which the main satellite, typically an ultra-large spacecraft or a space station in a higher orbit, is connected to a transport spacecraft in a lower orbit via a tether, maintaining orbital [...] Read more.

A partial space elevator (PSE) is a multi-body tethered space system in which the main satellite, typically an ultra-large spacecraft or a space station in a higher orbit, is connected to a transport spacecraft in a lower orbit via a tether, maintaining orbital synchronization. One or more climbers can move along the tether driven by electric power, enabling cross-orbital payload transportation between the two spacecraft. The climbers’ motion significantly alters the main satellite’s orbital states, compromising its safe and stable operation. The dynamic coupling and nonlinearity of the PSE further exacerbate this challenge. This study aims to preliminarily address this issue by proposing a new mission planning strategy. This strategy utilizes reinforcement learning (RL) to select the waiting interval between two transfer missions, thereby maintaining the main satellite’s orbital motion in a stable state. Simulation results confirm the feasibility and effectiveness of the proposed mission-based method. Full article

(This article belongs to the Special Issue Application of Tether Technology in Space)

► Show Figures

Figure 1

23 pages, 9625 KiB

Open AccessArticle

Effects of Build Direction and Heat Treatment on the Defect Characterization and Fatigue Properties of Laser Powder Bed Fusion Ti6Al4V

by Wenbo Sun, Yu’e Ma, Peiyao Li, Ziad Moumni and Weihong Zhang

Aerospace 2024, 11(10), 854; https://doi.org/10.3390/aerospace11100854 - 16 Oct 2024

Viewed by 714

Abstract

Laser powder bed fusion (LPBF) is one of the high-precision additive manufacturing techniques for producing complex 3D components. It is well known that defects appear in additive-manufactured parts, and they deeply affect the fatigue properties; even heat treatment is performed after printing. In [...] Read more.

Laser powder bed fusion (LPBF) is one of the high-precision additive manufacturing techniques for producing complex 3D components. It is well known that defects appear in additive-manufactured parts, and they deeply affect the fatigue properties; even heat treatment is performed after printing. In order to meet the safe-life design requirements of additive-manufactured aircraft structures, the effects of build direction and heat treatment on defects and fatigue properties need to be quantified. Hence, Ti6Al4V alloy samples with different build directions were designed and printed by LPBF. X-ray computed tomography was used to quantitatively analyze the defect size, the sphericity, and the defect orientation. And their effects on fatigue properties were studied. An extended effective defect size and a defect-based fatigue anisotropy evaluation process are proposed to qualify the effects of the defect size, sphericity, and defect orientation. It is shown that the build direction can affect the porosity distribution and maximum defect size, while the annealing treatment can cause the coalescence of small defects and higher porosity. The defect orientation exhibited a fluctuating trend of 0°–90°–0°–90°–0° as the volume increased. The elongated lack of fusion defects related to the build direction was the main crack source and could lead to fatigue anisotropy of LPBF Ti6Al4V. Full article

► Show Figures

Figure 1

17 pages, 2743 KiB

Open AccessArticle

Experimental Study on Ice Shedding Behaviors for Aero-Engine Fan Blade Icing during Ground Idle

by Liping Wang, Kun Yang, Fang Yu and Fuxin Wang

Aerospace 2024, 11(10), 853; https://doi.org/10.3390/aerospace11100853 - 16 Oct 2024

Viewed by 621

Abstract

Fan blade icing can affect efficiency and aerodynamic stability, and the shed ice may be sucked into the core of the engine, causing adverse effects or even damage to the compressor components. Ice accretion and shedding are among the key issues in engine [...] Read more.

Fan blade icing can affect efficiency and aerodynamic stability, and the shed ice may be sucked into the core of the engine, causing adverse effects or even damage to the compressor components. Ice accretion and shedding are among the key issues in engine design and tests. But they have not been clearly understood. In this work, ice shedding from rotating aero-engine fan blades during continuous icing is experimentally investigated under the relevant airworthiness requirements. The phenomena of icing and ice shedding under different ambient temperatures and engine speeds are recorded to obtain the ice-shedding time and the characteristic length of the residual ice. Force analysis is used to understand the corresponding behavior. The degree of ice-shedding balance

D_{b}

is defined to explore the symmetry of ice shedding. The results show that the shedding time is significantly affected by the rotational speed, and the characteristic length will first shorten and then grow as the ambient temperature decreases. When the ice shedding is completed instantaneously,

D_{b}

will show a violent shock. There is a critical ambient temperature, below which the ice accretion will worsen significantly as temperature decreases. For aero-engine fan blade icing tests during ground idle, the critical ambient temperature ranges from −

5^{\circ}

C to −

9^{\circ}

C. In order for the ice to shed faster, the engine speed has to reach a threshold. This study can shed light on the preliminary characteristics of ice shedding from rotating components and provide guidance and a data basis for the numerical simulation of fan blade icing and the design of an aero-engine. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

24 pages, 10038 KiB

Open AccessArticle

The Influence of Bleed Position on the Stability Expansion Effect of Self-Circulating Casing Treatment

by Haoguang Zhang, Jinhang Xiao, Xinyi Zhong, Yiming Feng and Wuli Chu

Aerospace 2024, 11(10), 852; https://doi.org/10.3390/aerospace11100852 - 16 Oct 2024

Viewed by 512

Abstract

The self-circulating casing treatment can effectively expand the stable working range of the compressor, with little impact on its efficiency. With a single-stage transonic axial flow compressor NASA (National Aeronautics and Space Administration) Stage 35 as the research object, a multi-channel unsteady numerical [...] Read more.

The self-circulating casing treatment can effectively expand the stable working range of the compressor, with little impact on its efficiency. With a single-stage transonic axial flow compressor NASA (National Aeronautics and Space Administration) Stage 35 as the research object, a multi-channel unsteady numerical calculation method was used here to design three types of self-circulating casing treatment structures: 20% Ca (axial chord length of the rotor blade tip), 60% Ca, and 178% Ca (at this time, the bleed position is at the stator channel casing) from the leading edge of the blade tip. The effects of these three bleed positions on the self-circulating stability expansion effect and compressor performance were studied separately. The calculation results indicate that the further the bleed position is from the leading edge of the blade tip, the weaker the expansion ability of the self-circulating casing treatment, and the greater the negative impact on the peak efficiency and design point efficiency of the compressor. This is because the air inlet of the self-circulating casing with an air intake position of 20% Ca is located directly above the core area of the rotor blade top blockage, which can more effectively extract low-energy fluid from the blockage area. Compared to the other two bleed positions, it has the greatest inhibitory effect on the leakage vortex in the rotor blade tip gap and has the strongest ability to improve the blockage at the rotor blade tip. Therefore, 20% Ca from the leading edge of the blade tip has the strongest stability expansion ability, achieving a stall margin improvement of 11.28%. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

19 pages, 9442 KiB

Open AccessArticle

Optimal Selection of Active Jet Parameters for a Ducted Tail Wing Aimed at Improving Aerodynamic Performance

by Huayu Jia, Huilong Zheng, Hong Zhou and Shunbo Huo

Aerospace 2024, 11(10), 851; https://doi.org/10.3390/aerospace11100851 - 15 Oct 2024

Viewed by 529

Abstract

The foldable tail of the box-type launch vehicle poses a risk of mechanical jamming during the launch process, which is not conducive to the smooth completion of the flight mission. The integrated nonfolding ducted tail proposed in this article can solve the problem [...] Read more.

The foldable tail of the box-type launch vehicle poses a risk of mechanical jamming during the launch process, which is not conducive to the smooth completion of the flight mission. The integrated nonfolding ducted tail proposed in this article can solve the problem of storing the tail in the launch box. Moreover, traditional mechanical control surfaces have been eliminated, and active jet control has been adopted to control the pitch direction of the flight attitude, which can improve the structural reliability of the tail wing. By studying the effects of parameters such as momentum coefficient, jet hole position, jet hole height, and jet angle on improving the aerodynamic performance of ducted tail wing, relatively good jet parameters are selected. Research has found that compared with jet hole height and jet angle, momentum coefficient and jet hole position are more effective in improving the aerodynamic performance of ducted tail wings. Under a trailing edge jet, a relatively good jet condition occurs when the jet hole height is equal to0.25% of the aerodynamic chord length, and the jet angle is equal to 0°. At this time, with the increase of the jet momentum coefficient, the effect of increasing the lift of the ducted tail wing is the best. Finally, a comparative analysis is conducted on the lift and drag characteristics between the ducted tail wing and traditional tail wing, and it is found that the ducted tail wing can generate lift at a 0° attack angle and will not stall in the high attack angle range of 12°~22°, with broad application prospects. Full article

(This article belongs to the Special Issue Aerodynamic Numerical Optimization in UAV Design)

► Show Figures

Figure 1

14 pages, 286 KiB

Open AccessArticle

Interaction of a Dense Layer of Solid Particles with a Shock Wave Propagating in a Tube

by Konstantin Volkov

Aerospace 2024, 11(10), 850; https://doi.org/10.3390/aerospace11100850 - 15 Oct 2024

Viewed by 462

Abstract

A numerical simulation of an unsteady gas flow containing inert solid particles in a shock tube is carried out using the interpenetrating continuum model. The gas and dispersed phases are characterized by governing equations that express the concepts of mass, momentum, and energy [...] Read more.

A numerical simulation of an unsteady gas flow containing inert solid particles in a shock tube is carried out using the interpenetrating continuum model. The gas and dispersed phases are characterized by governing equations that express the concepts of mass, momentum, and energy conservation as well as an equation that shows the change of the volume fraction of the dispersed phase. Using a Godunov-type approach, the hyperbolic governing equations are solved numerically with an increased order of accuracy. The working section of the shock tube containing air and solid particles of various sizes is considered. The shock wave structure is discussed and computational results provide the spatial and temporal dependencies of the particle concentration and other flow quantities. The numerical simulation results are compared with available experimental and computational data. Full article

(This article belongs to the Special Issue Flight at Supersonic and Hypersonic Velocities: Aerodynamics, Flow Control, Propulsion)

► Show Figures

Figure 1

18 pages, 8137 KiB

Open AccessArticle

Precision Manufacturing in China of Replication Mandrels for Ni-Based Monolithic Wolter-I X-ray Mirror Mandrels

by Jiadai Xue, Bo Wang, Qiuyan Liao, Kaiji Wu, Yutao Liu, Yangong Wu, Wentao Chen, Zheng Qiao, Yuan Jin, Fei Ding, Dianlong Wang, Langping Wang, Guo Li, Yanji Yang and Yong Chen

Aerospace 2024, 11(10), 849; https://doi.org/10.3390/aerospace11100849 - 15 Oct 2024

Viewed by 583

Abstract

The X-ray satellite “Einstein Probe” of the Chinese Academy of Sciences (CAS) was successfully launched on 9 January 2024 at 15:03 Beijing Time from the Xichang Satellite Launch Center in China with a “Long March-2C” rocket. The Einstein Probe is equipped with two [...] Read more.

The X-ray satellite “Einstein Probe” of the Chinese Academy of Sciences (CAS) was successfully launched on 9 January 2024 at 15:03 Beijing Time from the Xichang Satellite Launch Center in China with a “Long March-2C” rocket. The Einstein Probe is equipped with two scientific X-ray telescopes. One is the Wide-field X-ray Telescope (WXT), which uses lobster-eye optics. The other is the Follow-up X-ray Telescope (FXT), a Wolter-I type telescope. These telescopes are designed to study the universe for high-energy X-rays associated with transient high-energy phenomena. The FXT consists of two modules based on 54 thin X-ray Wolter-I grazing incidence Ni-replicated mirrors produced by the Italian Media Lario company, as contributions from the European Space Agency and the Max Planck Institute for Extraterrestrial Physics (MPE), which also provided the focal-plane detectors. Meanwhile, the Institute of High Energy Physics (IHEP), together with the Harbin Institute of Technology and Xi’an Institute of Optics and Precision Mechanics, has also completed the development and production of the structural and thermal model (STM), qualification model (QM) and flight model (FM) of FXT mirrors for the Einstein Probe (EP) satellites for demonstration purposes. This paper introduces the precision manufacturing adopted in China of Wolter-I X-ray mirror mandrels similar to those used for the EP-FXT payload. Moreover, the adopted electroformed nickel replication process, based on a chemical nickel–phosphorus alloy, is reported. The final results show that the surface of the produced mandrels after demolding and the internal surface of the mirrors have been super polished to the roughness level better than 0.3 nm RMS and the surface accuracy is better than 0.2 μm, and the mirror angular resolution for single mirror shells may be as good as 17.3 arcsec HPD (Half Power Diameter), 198 arcsec W90 (90% Energy Width) @1.49 keV (Al-K line). These results demonstrate the reliability and advancement of the process. As the first efficient X-ray-focusing optics manufacturing chain established in China, we successfully developed the first focusing mirror prototype that could be used for future X-ray satellite payloads. Full article

► Show Figures

Figure 1

15 pages, 8364 KiB

Open AccessArticle

Research on the Design and Bidirectional Work Process of Metal Diaphragms in Small Double-Pulse Solid Rocket Motors

by Xueqin Du, Weihua Hui, Youwen Tan, Wen Feng and Yang Liu

Aerospace 2024, 11(10), 848; https://doi.org/10.3390/aerospace11100848 - 15 Oct 2024

Viewed by 964

Abstract

According to the requirements of the small double-pulse solid rocket motor, a compartmentalized isolation device has been designed. This device consists of a metal diaphragm and a support frame. An experimental study and numerical simulation were used to verify the bidirectional working process [...] Read more.

According to the requirements of the small double-pulse solid rocket motor, a compartmentalized isolation device has been designed. This device consists of a metal diaphragm and a support frame. An experimental study and numerical simulation were used to verify the bidirectional working process of the metal diaphragm during operation of the double-pulse motor. The results show that the pressure-bearing capacity of the metal diaphragm meets the requirements under the working conditions of pulse I without affecting pulse II, because the metal diaphragm can provide insulation and flame retardancy. The metal diaphragm can be cracked in the direction of the preset V-groove in a relatively short time under the working conditions of pulse II, which allows the gas to flow to the first pulse combustion chamber normally. This indicates that the metal diaphragm can meet the requirements of bidirectional working process in dual-pulse motors. Full article

(This article belongs to the Section Astronautics & Space Science)

► Show Figures

Figure 1

13 pages, 10265 KiB

Open AccessArticle

Effects of Non-Uniform Center-Flow Distribution and Cavitation on Continuous-Type Pintle Injectors

by Dongwoo Choi, Seunghyeon Lee and Kyubok Ahn

Aerospace 2024, 11(10), 847; https://doi.org/10.3390/aerospace11100847 - 15 Oct 2024

Viewed by 518

Abstract

In this paper, the flow characteristics of a continuous-type liquid–liquid pintle injector are described, focusing on the differential impact of a non-uniform center-flow distribution on single- and bi-injection methodologies as well as the cavitation effect on the spray angle. Using cold-flow experiments, jet-type [...] Read more.

In this paper, the flow characteristics of a continuous-type liquid–liquid pintle injector are described, focusing on the differential impact of a non-uniform center-flow distribution on single- and bi-injection methodologies as well as the cavitation effect on the spray angle. Using cold-flow experiments, jet-type flows of the center propellant caused by a non-uniform flow distribution were observed during a single injection. This resulted in an augmented pressure drop, as opposed to the flow characteristics of uniform single-film injection. By contrast, bi-injection modalities exhibited a substantial reduction in the pressure drop of the center propellant, underscoring a more equitable flow distribution. Moreover, the occurrence of cavitation in the center propellant was found to markedly affect the spray angle. By considering the injection exit area reduction caused by cavitation, the spray-angle prediction accuracy increased. The findings of this study are expected to reveal the interplay between flow distribution and pressure drop as well as that between cavitation and the spray angle in pintle injectors. Through this understanding, this study provides crucial considerations for the development of more efficient propulsion systems. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

22 pages, 4104 KiB

Open AccessArticle

Modeling and Performance Analysis of Solid Oxide Fuel Cell Power Generation System for Hypersonic Vehicles

by Yiming Liu, Jianguo Tan, Dongdong Zhang and Zihan Kuai

Aerospace 2024, 11(10), 846; https://doi.org/10.3390/aerospace11100846 - 14 Oct 2024

Viewed by 777

Abstract

Advanced airborne power generation technology represents one of the most effective solutions for meeting the electricity requirements of hypersonic vehicles during long-endurance flights. This paper proposes a power generation system that integrates a high-temperature fuel cell to tackle the challenges associated with power [...] Read more.

Advanced airborne power generation technology represents one of the most effective solutions for meeting the electricity requirements of hypersonic vehicles during long-endurance flights. This paper proposes a power generation system that integrates a high-temperature fuel cell to tackle the challenges associated with power generation in the hypersonic field, utilizing techniques such as inlet pressurization, autothermal reforming, and anode recirculation. Firstly, the power generation system is modeled modularly. Secondly, the influence of key parameters on the system’s performance is analyzed. Thirdly, the performance of the power generation system under the design conditions is simulated and evaluated. Finally, the weight distribution and exergy loss of the system’s components under the design conditions are calculated. The results indicate that the system’s electrical efficiency increases with fuel utilization, decreases with rising current density and steam-to-carbon ratio (SCR), and initially increases before declining with increasing fuel cell operating temperature. Under the design conditions, the system’s power output is 48.08 kW, with an electrical efficiency of 51.77%. The total weight of the power generation system is 77.09 kg, with the fuel cell comprising 69.60% of this weight, resulting in a power density of 0.62 kW/kg. The exergy efficiency of the system is 55.86%, with the solid oxide fuel cell (SOFC) exhibiting the highest exergy loss, while the mixer demonstrates the greatest exergy efficiency. This study supports the application of high-temperature fuel cells in the hypersonic field. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

16 pages, 3196 KiB

Open AccessArticle

A Cooperative Control Method for Wide-Range Maneuvering of Autonomous Aerial Refueling Controllable Drogue

by Jinxin Bai and Zhongjie Meng

Aerospace 2024, 11(10), 845; https://doi.org/10.3390/aerospace11100845 - 14 Oct 2024

Viewed by 541

Abstract

In the realm of autonomous aerial refueling missions for unmanned aerial vehicles (UAVs), the controllable drogue represents a novel approach that significantly enhances both the safety and efficiency of aerial refueling operations. This paper delves into the issue of wide-range maneuverability control for [...] Read more.

In the realm of autonomous aerial refueling missions for unmanned aerial vehicles (UAVs), the controllable drogue represents a novel approach that significantly enhances both the safety and efficiency of aerial refueling operations. This paper delves into the issue of wide-range maneuverability control for the controllable drogue. Initially, a dynamic model for the variable-length hose–drogue system is presented. Based on this, a cooperative control framework that synergistically utilizes both the hose and the drogue is designed to achieve wide-range maneuverability of the drogue. To address the delay in hose retrieval and release, an open-loop control strategy based on neural networks is proposed. Furthermore, a closed-loop control method utilizing fuzzy approximation and adaptive error estimation is designed to tackle the challenges posed by modeling inaccuracies and uncertainties in aerodynamic parameters. Comparative simulation results show that the proposed control strategy can make the drogue maneuvering range reach more than 6 m. And it can accurately track the time-varying trajectory under the influence of model uncertainty and wind disturbance with an error of less than 0.1 m throughout. This method provides an effective means for achieving wide-range maneuverability control of the controllable drogue in autonomous aerial refueling missions. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

30 pages, 35792 KiB

Open AccessArticle

Research on the Structural Design of a Pressurized Cabin for Civil High-Speed Rotorcraft and the Multi-Dimensional Comprehensive Evaluation Method

by Yongjie Zhang, Tongxin Zhang, Jingpiao Zhou, Bo Cui and Fangyu Chen

Aerospace 2024, 11(10), 844; https://doi.org/10.3390/aerospace11100844 - 13 Oct 2024

Viewed by 623

Abstract

For civil high-speed rotorcraft designed to operate at specific cruising altitudes, this study proposes nine structural design schemes for pressurized cabins. These schemes integrate commonly used materials and processing technologies in the aviation industry with advanced PRSEUS (Pultruded Rod Stitched Efficient Unitized Structure) [...] Read more.

For civil high-speed rotorcraft designed to operate at specific cruising altitudes, this study proposes nine structural design schemes for pressurized cabins. These schemes integrate commonly used materials and processing technologies in the aviation industry with advanced PRSEUS (Pultruded Rod Stitched Efficient Unitized Structure) technology. An analysis of the structural composition reveals that frames constitute 8–19% of the total structural weight, while stringers and beams make up 15–50%, and skins account for 11–25%, with thicknesses ranging from 1.0 mm to 2.0 mm. The separating interface of the pressurized cabin contributes 4–29% of the total structural weight. The weight distribution of each component in the pressurized cabin structure varies significantly depending on the chosen materials and processing technologies. Utilizing the Analytic Hierarchy Process (AHP), along with Gray Relational Analysis (GRA) and Dempster–Shafer (D-S) evidence theory, this study compares the simulation results of the nine schemes across multiple dimensions. The findings indicate that the configuration combining 7075 aluminum alloy and T300 composite material has the greatest advantages in terms of the high structural reliability of the configuration, light weight, mature processing technology, and low production cost. This comprehensive evaluation method quantitatively analyzes the factors influencing the structural configuration design of the pressurized cabin for civil high-speed rotorcraft, offering a valuable reference for the design of similar structures in related fields. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

22 pages, 9686 KiB

Open AccessArticle

From Text to Safety: A Novel Framework for Mining Unsafe Aviation Events Using Advanced Neural Network and Feature Network

by Qiang Wang, Ruicong Xia, Jiayang Yu, Qiuhan Liu, Sirong Tong and Ziling Xu

Aerospace 2024, 11(10), 843; https://doi.org/10.3390/aerospace11100843 - 12 Oct 2024

Viewed by 632

Abstract

The rapid growth of the aviation industry highlights the need for strong safety management. Analyzing data on unsafe aviation events is crucial for preventing risks. This paper presents a new method that integrates the Transformer network model, clustering analysis, and feature network modeling [...] Read more.

The rapid growth of the aviation industry highlights the need for strong safety management. Analyzing data on unsafe aviation events is crucial for preventing risks. This paper presents a new method that integrates the Transformer network model, clustering analysis, and feature network modeling to analyze Chinese text data on unsafe aviation events. Initially, the Transformer model is used to generate summaries of event texts, and the performance of three pre-trained Chinese models is evaluated and compared. Next, the Jieba tool is applied to segment both summarized and original texts to extract key features of unsafe events and prove the effectiveness of the pre-trained Transformer model in simplifying lengthy and redundant original texts. Then, cluster analysis based on text similarity categorizes the extracted features. By solving the correlation matrix of these features, this paper constructs a feature network for unsafe aviation events. The network’s global and individual metrics are calculated and then used to identify key feature nodes, which alert aviation professionals to focus more on the decision-making process for safety management. Based on the established network and these metrics, a data-driven hidden danger warning strategy is proposed and illustrated. Overall, the proposed method can effectively analyze Chinese texts of unsafe aviation events and provide a basis for improving aviation safety management. Full article

(This article belongs to the Section Air Traffic and Transportation)

► Show Figures

Figure 1

25 pages, 352 KiB

Open AccessArticle

Assessing the Principle of Equitable Access versus Non-Appropriation in the Era of Mega-Constellations

by Kuan Yang and Sandra Amongin

Aerospace 2024, 11(10), 842; https://doi.org/10.3390/aerospace11100842 - 12 Oct 2024

Viewed by 685

Abstract

In the 21st century, mega-constellations and interconnected satellite constellations deployed at various orbital altitudes, such as LEO, MEO, and GEO, with low Earth orbits (LEOs) being the most commonly used, have emerged as a trend, aiming to enhance the productivity and reduce the [...] Read more.

In the 21st century, mega-constellations and interconnected satellite constellations deployed at various orbital altitudes, such as LEO, MEO, and GEO, with low Earth orbits (LEOs) being the most commonly used, have emerged as a trend, aiming to enhance the productivity and reduce the costs in space service delivery. The UNOOSA has noted the uncertainty in the exact number of satellites but conducted simulations based on a substantial sample, projecting a significant increase from the 2075 satellites recorded in orbit in 2018. This surge in the launch of mega-constellations poses profound challenges to existing international space laws, originally formulated with limited consideration for private space actors, who are increasingly engaging in space activities, particularly with the cost-effective utilization of mega-constellations. This study critically analyzes the compatibility of mega-constellations with the current international space laws by examining the applicability of mega-constellations concerning equitable access and the non-appropriation principle, addressing their potential occupation of substantial orbital spaces during activities, and analyzing whether the acquisition of orbital slot licenses violates these two principles. Following an in-depth analysis, this study proposes recommendations to amend the existing laws, aiming to resolve ambiguities and address emerging challenges. Recognizing the time-consuming process of amending international space laws, this study suggests practical recommendations for supplementary rules of the road, prompting reflection on the potential obsolescence of the current international space laws in the face of evolving space activities. Full article

(This article belongs to the Special Issue Advanced Technology of Distributed Space Systems: Formation-Flying, Swarms, and Constellations)

16 pages, 8740 KiB

Open AccessArticle

Crack Growth Analytical Model Considering the Crack Growth Resistance Parameter Due to the Unloading Process

by Guo Li, Shuchun Huang, Zhenlei Li, Wanqiu Lu, Shuiting Ding, Rong Chen and Fan Cao

Aerospace 2024, 11(10), 841; https://doi.org/10.3390/aerospace11100841 - 12 Oct 2024

Viewed by 554

Abstract

Crack growth analysis is essential for probabilistic damage tolerance assessment of aeroengine life-limited parts. Traditional crack growth models directly establish the stress ratio–crack growth rate or crack opening stress relationship and focus less on changes in the crack tip stress field and its [...] Read more.

Crack growth analysis is essential for probabilistic damage tolerance assessment of aeroengine life-limited parts. Traditional crack growth models directly establish the stress ratio–crack growth rate or crack opening stress relationship and focus less on changes in the crack tip stress field and its influence, so the resolution and accuracy of maneuvering flight load spectral analysis are limited. To improve the accuracy and convenience of analysis, a parameter considering the effect of unloading amount on crack propagation resistance is proposed, and the corresponding analytical model is established. The corresponding process for acquiring the model parameters through the constant amplitude test data of a Ti-6AL-4V compact tension specimen is presented. Six kinds of flight load spectra with inserted load pairs with different stress ratios and repetition times are tested to verify the accuracy of the proposed model. All the deviations between the proposed model and test life results are less than 10%, which demonstrates the superiority of the proposed model over the crack closure and Walker-based models in addressing relevant loading spectra. The proposed analytical model provides new insights for the safety of aeroengine life-limited parts. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

15 pages, 4335 KiB

Open AccessArticle

Rapid Aircraft Wake Vortex Identification Model Based on Optimized Image Object Recognition Networks

by Leilei Deng, Weijun Pan, Tian Luan, Chen Zhang and Yuanfei Leng

Aerospace 2024, 11(10), 840; https://doi.org/10.3390/aerospace11100840 - 11 Oct 2024

Viewed by 683

Abstract

Wake vortices generated by aircraft during near-ground operations have a significant impact on airport safety during takeoffs and landings. Identifying wake vortices in complex airspaces assists air traffic controllers in making informed decisions, ensuring the safety of aircraft operations at airports, and enhancing [...] Read more.

Wake vortices generated by aircraft during near-ground operations have a significant impact on airport safety during takeoffs and landings. Identifying wake vortices in complex airspaces assists air traffic controllers in making informed decisions, ensuring the safety of aircraft operations at airports, and enhancing the intelligence level of air traffic control. Unlike traditional image recognition, identifying wake vortices using airborne LiDAR data demands a higher level of accuracy. This study proposes the IRSN-WAKE network by optimizing the Inception-ResNet-v2 network. To improve the model’s feature representation capability, we introduce the SE module into the Inception-ResNet-v2 network, which adaptively weights feature channels to enhance the network’s focus on key features. Additionally, we design and incorporate a noise suppression module to mitigate noise and enhance the robustness of feature extraction. Ablation experiments demonstrate that the introduction of the noise suppression module and the SE module significantly improves the performance of the IRSN-WAKE network in wake vortex identification tasks, achieving an accuracy rate of 98.60%. Comparative experimental results indicate that the IRSN-WAKE network has higher recognition accuracy and robustness compared to common recognition networks, achieving high-accuracy aircraft wake vortex identification and providing technical support for the safe operation of flights. Full article

(This article belongs to the Special Issue Advances in Air Traffic and Airspace Control and Management (2nd Edition))

► Show Figures

Figure 1

22 pages, 9498 KiB

Open AccessArticle

Pulsar Signal Adaptive Surrogate Modeling

by Tomáš Kašpárek and Peter Chudý

Aerospace 2024, 11(10), 839; https://doi.org/10.3390/aerospace11100839 - 11 Oct 2024

Viewed by 411

Abstract

As the number of spacecraft heading beyond Earth’s orbit increased in recent years, autonomous navigation solutions have become increasingly important. One such solution is pulsar-based navigation. The availability of pulsar signals for simulations and HIL testing is essential for the development of pulsar-based [...] Read more.

As the number of spacecraft heading beyond Earth’s orbit increased in recent years, autonomous navigation solutions have become increasingly important. One such solution is pulsar-based navigation. The availability of pulsar signals for simulations and HIL testing is essential for the development of pulsar-based navigation. This study proposes a method to develop a surrogate model of pulsar signals based on radio pulsar observations. The selection of suitable pulsars for the radio telescope is discussed, and a series of observations are conducted. The collected data are processed using the PRESTO software, and the pulsar parameters for the model are derived. Unlike current pulsar signal models, the proposed model anticipates pulsar signal parameters to change over time. It can provide dynamic input parameters for known synthetic pulsar signal generators, resulting in a more realistic signal. Full article

► Show Figures

Figure 1

19 pages, 12747 KiB

Open AccessArticle

State Analysis and Emergency Control of Planetary Rover with Faulty Drive Wheel

by Zhicheng Jia, Jingfu Jin, Xinju Dong, Yingchun Qi, Meng Zou and Qingyu Yu

Aerospace 2024, 11(10), 838; https://doi.org/10.3390/aerospace11100838 - 11 Oct 2024

Viewed by 532

Abstract

Wheel failure is one of the worst problems for a planetary rover working on Mars or the Moon, which may lead to the interruption of the exploration mission and even the loss of mobility. In this study, a driving test of a planetary [...] Read more.

Wheel failure is one of the worst problems for a planetary rover working on Mars or the Moon, which may lead to the interruption of the exploration mission and even the loss of mobility. In this study, a driving test of a planetary rover prototype with a faulty drive wheel was conducted, and state analysis and dynamics modeling were carried out. The drag motion relationship between the faulty drive wheel and the normal wheels on the same suspension was established based on the targeted single wheel test (faulty wheel-soil bin). In order to maintain the subsequent basic detection capability of the planetary rover, an emergency control system is proposed that integrates the path planning strategy with faulty wheel priority and the motion control method of correcting heading and coordinating allocation. The experimental results and emergency strategies of this study on simulating Martian soil and terrain can provide researchers with ideas to solve such problems. Full article

(This article belongs to the Section Astronautics & Space Science)

► Show Figures

Figure 1

24 pages, 5059 KiB

Open AccessArticle

Hazard Analysis for Massive Civil Aviation Safety Oversight Reports Using Text Classification and Topic Modeling

by Yaxi Xu, Zurui Gan, Rengang Guo, Xin Wang, Ke Shi and Pengfei Ma

Aerospace 2024, 11(10), 837; https://doi.org/10.3390/aerospace11100837 - 11 Oct 2024

Viewed by 548

Abstract

There are massive amounts of civil aviation safety oversight reports collected each year in the civil aviation of China. The narrative texts of these reports are typically short texts, recording the abnormal events detected during the safety oversight process. In the construction of [...] Read more.

There are massive amounts of civil aviation safety oversight reports collected each year in the civil aviation of China. The narrative texts of these reports are typically short texts, recording the abnormal events detected during the safety oversight process. In the construction of an intelligent civil aviation safety oversight system, the automatic classification of safety oversight texts is a key and fundamental task. However, all safety oversight reports are currently analyzed and classified into categories by manual work, which is time consuming and labor intensive. In recent years, pre-trained language models have been applied to various text mining tasks and have proven to be effective. The aim of this paper is to apply text classification to the mining of these narrative texts and to show that text classification technology can be a critical element of the aviation safety oversight report analysis. In this paper, we propose a novel method for the classification of narrative texts in safety oversight reports. Through extensive experiments, we validated the effectiveness of all the proposed components. The experimental results demonstrate that our method outperforms existing methods on the self-built civil aviation safety oversight dataset. This study undertakes a thorough examination of the precision and associated outcomes of the dataset, thereby establishing a solid basis for furnishing valuable insights to enhance data quality and optimize information. Full article

(This article belongs to the Special Issue Machine Learning for Aeronautics (2nd Edition))

► Show Figures

Figure 1

23 pages, 9577 KiB

Open AccessArticle

Evolution of Rotating Internal Channel for Heat Transfer Enhancement in a Gas Turbine Blade

by Xinxin Guo, Xueying Li and Jing Ren

Aerospace 2024, 11(10), 836; https://doi.org/10.3390/aerospace11100836 - 11 Oct 2024

Viewed by 714

Abstract

To achieve higher thermal efficiency in a gas turbine, increasing the turbine inlet temperature is necessary. The rotor blade at the first stage tolerates the highest temperature, and the serpentine internal channel located in the middle chord of the rotor blade is vital [...] Read more.

To achieve higher thermal efficiency in a gas turbine, increasing the turbine inlet temperature is necessary. The rotor blade at the first stage tolerates the highest temperature, and the serpentine internal channel located in the middle chord of the rotor blade is vital in guaranteeing the blade’s service life. Therefore, it is essential to illustrate the evolution of the rotating internal channel in a gas turbine blade. In the paper, the influence of the Coriolis force, including its mechanisms, on the conventional rotating channel are reviewed and analyzed. A way to utilize the positive heat transfer effect of the Coriolis force is proposed. Recent investigations on corresponding novel rotating channels with a channel orientation angle of 90° (called bilaterally enhanced U-channels) are illustrated. Moreover, numerical investigations about the Re effects on bilaterally enhanced smooth U-channels were carried out in the study. The results indicated that bilaterally enhanced U-channels can utilize the Coriolis force positive heat transfer effect on the leading and the trailing walls at the same time. Re and Ro are vital non-dimensional numbers that influence the performance of bilaterally enhanced U-channels. Re and Ro have an independent influence on the heat transfer performance of the bilaterally enhanced U-channel. Ro is good for the heat transfer of the bilaterally enhanced U-channel on both the leading and the trailing walls. Therefore, the bilaterally enhanced U-channel is suitable for application in the middle chord region of a turbine blade, since it can utilize the rotation effect of the rotating blade to improve the heat transfer ability of the blade and thus reduced the blade temperature. At the same Ro, Re positively affects the Nu on the leading and the trailing walls of the Coriolis-utilization rotating smooth U-channel, but plays a negligible role on Nu/Nu₀. Full article

(This article belongs to the Special Issue New Insights into Aerodynamics and Cooling in Gas Turbine Engines)

► Show Figures

Figure 1

11 pages, 6060 KiB

Open AccessArticle

Investigation of Asymmetric Flow of a Slender Body with Low-Aspect Ratio Fins Having Large Deflection Angles

by Yonghong Li, Lin Zhang, Chuan Gao, Jilong Zhu and Bin Dong

Aerospace 2024, 11(10), 835; https://doi.org/10.3390/aerospace11100835 - 10 Oct 2024

Viewed by 512

Abstract

To understand the asymmetric flow of a slender body with low-aspect ratio fins, a wind tunnel experiment was carried out, and the asymmetric flow was observed when the pair of fins had a symmetric deflection angle of 30° at a small angle of [...] Read more.

To understand the asymmetric flow of a slender body with low-aspect ratio fins, a wind tunnel experiment was carried out, and the asymmetric flow was observed when the pair of fins had a symmetric deflection angle of 30° at a small angle of attack and zero sideslip angle at transonic speeds. The unsteady characteristics of flow around the moving fins, especially for the evolution of the asymmetric flow, was carefully numerically investigated via the RANS method. To verify the numerical method, the experimental steady wind tunnel data of the NACA 0012 airfoil with sinusoidal pitching motion were adopted. A hysteresis loop exists as a function of the deflection angle during the upstroke and downstroke motions. The side force is periodic due to the asymmetric flow peaks at the downstroke and their peak value appeared at around δz = 25°, which was independent of the deflection frequency. As the deflection frequency increased, the asymmetric flow formed at a higher deflection angle during the upstroke motion, but decayed at a lower deflection angle during the downstroke motion, resulting in a more significant unsteady hysteresis effect. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

22 pages, 13437 KiB

Open AccessArticle

A Novel Approach to Ripple Cancellation for Low-Speed Direct-Drive Servo in Aerospace Applications

by Xin Zhang, Ziting Wang, Chaoping Bai and Shuai Zhang

Aerospace 2024, 11(10), 834; https://doi.org/10.3390/aerospace11100834 - 10 Oct 2024

Viewed by 636

Abstract

Low-frequency harmonic interference is an important factor that affects the performance of low-speed direct-drive servo systems. In order to improve the low-speed smoothness of direct-drive servo, firstly, the causes of the first and second harmonics of electromagnetic torque and tooth harmonics are analyzed [...] Read more.

Low-frequency harmonic interference is an important factor that affects the performance of low-speed direct-drive servo systems. In order to improve the low-speed smoothness of direct-drive servo, firstly, the causes of the first and second harmonics of electromagnetic torque and tooth harmonics are analyzed based on the mathematical model of PMSM (permanent magnet synchronous motor) and the principle of vector control. Accordingly, the CC-EUMA (Electrical angle Update and Mechanical angle Assignment algorithm for Center Current) and SL-DQPR (Double Quasi-Proportional Resonant control algorithm for Speed Loop) algorithm are proposed. Second, to confirm the algorithm’s efficacy, the harmonic environment is simulated using Matlab/Simulink, and the built harmonic suppression module is simulated and analyzed. Then, a miniaturized, fully digital drive control system is built based on the architecture of the Zynq-7000 series chips. Finally, the proposed suppression algorithm is verified at the board level. According to the experimental results, the speed ripple decreases to roughly one-third of its initial value after the algorithm is included. This effectively delays the speed ripple’s low-speed deterioration and provides a new idea for the low-speed control of the space direct-drive servo system. Full article

(This article belongs to the Special Issue Aircraft Electric Power System: Design, Control, and Maintenance)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Aerospace, Volume 11, Issue 10 (October 2024) – 76 articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI