Energies

Research

Jump to: Other

6526 KiB

Open AccessArticle

Coordination Control Strategy for AC/DC Hybrid Microgrids in Stand-Alone Mode

by Dwi Riana Aryani and Hwachang Song

Energies 2016, 9(6), 469; https://doi.org/10.3390/en9060469 - 18 Jun 2016

Cited by 39 | Viewed by 7616

Abstract

Interest in DC microgrids is rapidly increasing along with the improvement of DC power technology because of its advantages. To support the integration process of DC microgrids with the existing AC utility grids, the form of hybrid AC/DC microgrids is considered for higher [...] Read more.

Interest in DC microgrids is rapidly increasing along with the improvement of DC power technology because of its advantages. To support the integration process of DC microgrids with the existing AC utility grids, the form of hybrid AC/DC microgrids is considered for higher power conversion efficiency, lower component cost and better power quality. In the system, AC and DC portions are connected through interlink bidirectional AC/DC converters (IC) with a proper control system and power management. In the stand-alone operation mode of AC/DC hybrid microgrids, the control of power injection through the IC is crucial in order to maintain the system security. This paper mainly deals with a coordination control strategy of IC and a battery energy storage system (BESS) converter under stand-alone operation. A coordinated control strategy for the IC, which considers the state of charge (SOC) level of BESS and the load shedding scheme as the last resort, is proposed to obtain better power sharing between AC and DC subgrids. The scheme will be tested with a hybrid AC/DC microgrid, using the tool of the PSCAD/EMTDC software. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

8541 KiB

Open AccessArticle

Effect of Borehole Material on Analytical Solutions of the Heat Transfer Model of Ground Heat Exchangers Considering Groundwater Flow

by Sangwoo Park, Seokjae Lee, Hyobum Lee, Khanh Pham and Hangseok Choi

Energies 2016, 9(5), 318; https://doi.org/10.3390/en9050318 - 25 Apr 2016

Cited by 14 | Viewed by 5302

Abstract

Groundwater flow is one of the most important factors for the design of a ground heat exchanger (GHEX) since the thermal environment of the ground around the buried GHEX is significantly affected by heat convection due to the groundwater flow. Several preceding studies [...] Read more.

Groundwater flow is one of the most important factors for the design of a ground heat exchanger (GHEX) since the thermal environment of the ground around the buried GHEX is significantly affected by heat convection due to the groundwater flow. Several preceding studies have been conducted to develop analytical solutions to the heat transfer model of GHEX with consideration of groundwater flow. One of these solutions is the combined heat transfer model of conduction and convection. However, the developed combined analytical models are inapplicable to all of the configurations of ordinary GHEXs because these solutions assume that the inner part of the borehole is thermally inert or consists of the same material as that of the surrounding ground. In this paper, the applicability of the combined solid cylindrical heat source model, which is the most suitable to energy piles until now, was evaluated by performing a series of numerical analyses. In the numerical analysis, the inner part of the borehole was modeled as two different materials (i.e., permeable ground formation and impermeable fill such as concrete) to evaluate applicability of the analytical solution along with different diameter-length (D/L) ratios of borehole. In a small value of the D/L ratio, the analytical solution to the combined heat transfer model is in good agreement with the result of numerical analysis. On the other hand, when increasing the D/L ratio, the analytical solution significantly overestimates the effect of groundwater flow on the heat transfer of GHEXs because the analytical solution disregards the existence of the impermeable region in the borehole. Consequently, such tendency is more critical in the GHEX with a large D/L ratio such as large-diameter energy piles. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Graphical abstract

9540 KiB

Open AccessArticle

Effect of Guide Vane Clearance Gap on Francis Turbine Performance

by Ravi Koirala, Baoshan Zhu and Hari Prasad Neopane

Energies 2016, 9(4), 275; https://doi.org/10.3390/en9040275 - 11 Apr 2016

Cited by 38 | Viewed by 11647

Abstract

Francis turbine guide vanes have pivoted support with external control mechanism, for conversion of pressure to kinetic energy and to direct them to runner vanes. This movement along the support is dependent on variation of load and flow (operating conditions). Small clearance gaps [...] Read more.

Francis turbine guide vanes have pivoted support with external control mechanism, for conversion of pressure to kinetic energy and to direct them to runner vanes. This movement along the support is dependent on variation of load and flow (operating conditions). Small clearance gaps between facing plates and the upper and lower guide vane tips are available to aid this movement, through which leakage flow occurs. This secondary flow disturbs the main flow stream, resulting performance loss. Additionally, these increased horseshoe vortex, in presence of sand, when crosses through the gaps, both the surfaces are eroded. This causes further serious effect on performance and structural property by increasing gaps. This paper discusses the observation of the severity in hydropower plants and effect of clearance gaps on general performance of the Francis turbine through computational methods. It also relates the primary result with the empirical relation for leakage flow prediction. Additionally, a possible method to computationally estimate thickness depletion has also been presented. With increasing clearance gap, leakage increases, which lowers energy conversion and turbine efficiency along with larger secondary vortex. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

6670 KiB

Open AccessArticle

Waste Heat Recovery of a PEMFC System by Using Organic Rankine Cycle

by Tianqi He, Rongqi Shi, Jie Peng, Weilin Zhuge and Yangjun Zhang

Energies 2016, 9(4), 267; https://doi.org/10.3390/en9040267 - 5 Apr 2016

Cited by 32 | Viewed by 8683

Abstract

In this study, two systems are brought forward to recover the waste heat of a proton exchange membrane fuel cell (PEMFC), which are named the organic Rankine cycle (ORC), and heat pump (HP) combined organic Rankine cycle (HPORC). The performances of both systems [...] Read more.

In this study, two systems are brought forward to recover the waste heat of a proton exchange membrane fuel cell (PEMFC), which are named the organic Rankine cycle (ORC), and heat pump (HP) combined organic Rankine cycle (HPORC). The performances of both systems are simulated on the platform of MATLAB with R123, R245fa, R134a, water, and ethanol being selected as the working fluid, respectively. The results show that, for PEMFC where operating temperature is constantly kept at 60 °C, there exists an optimum working temperature for each fluid in ORC and HPORC. In ORC, the maximal net power can be achieved with R245fa being selected as the working fluid. The corresponding thermal efficiency of the recovery system is 4.03%. In HPORC, the maximal net power can be achieved with water being selected in HP and R123 in ORC. The thermal efficiency of the recovery system increases to 4.73%. Moreover, the possibility of using ORC as the cooling system of PEMFC is also studied. The heat released from PEMFC stack is assumed to be wholly recovered by the ORC or HPORC system. The results indicate that the HPORC system is much more feasible for the cooling system of a PEMFC stack, since the heat recovery ability can be promoted due to the presence of HP. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

12033 KiB

Open AccessArticle

Reduced-Capacity Inrush Current Suppressor Using a Matrix Converter in a Wind Power Generation System with Squirrel-Cage Induction Machines

by Sho Shibata, Hiroaki Yamada, Toshihiko Tanaka and Masayuki Okamoto

Energies 2016, 9(3), 223; https://doi.org/10.3390/en9030223 - 21 Mar 2016

Cited by 6 | Viewed by 5860

Abstract

This paper describes the reduced capacity of the inrush current suppressor using a matrix converter (MC) in a large-capacity wind power generation system (WPGS) with two squirrel-cage induction machines (SCIMs). These SCIMs are switched over depending on the wind speed. The input side [...] Read more.

This paper describes the reduced capacity of the inrush current suppressor using a matrix converter (MC) in a large-capacity wind power generation system (WPGS) with two squirrel-cage induction machines (SCIMs). These SCIMs are switched over depending on the wind speed. The input side of the MC is connected to the source in parallel. The output side of the MC is connected in series with the SCIM through matching transformers. The modulation method of the MC used is direct duty ratio pulse width modulation. The reference output voltage of the MC is decided by multiplying the SCIM current with the variable control gain. Therefore, the MC performs as resistors for the inrush current. Digital computer simulation is implemented to confirm the validity and practicability of the proposed inrush current suppressor using PSCAD/EMTDC (power system computer-aided design/electromagnetic transients including DC). Furthermore, the equivalent resistance of the MC is decided by the relationship between the equivalent resistance and the capacity of the MC. Simulation results demonstrate that the proposed inrush current suppressor can suppress the inrush current perfectly. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

3903 KiB

Open AccessArticle

Catalytic Pyrolysis of Wild Reed over a Zeolite-Based Waste Catalyst

by Myung Lang Yoo, Yong Ho Park, Young-Kwon Park and Sung Hoon Park

Energies 2016, 9(3), 201; https://doi.org/10.3390/en9030201 - 15 Mar 2016

Cited by 10 | Viewed by 5372

Abstract

Fast catalytic pyrolysis of wild reed was carried out at 500 °C. Waste fluidized catalytic cracking (FCC) catalyst disposed from a petroleum refinery process was activated through acetone-washing and calcination and used as catalyst for pyrolysis. In order to evaluate the catalytic activity [...] Read more.

Fast catalytic pyrolysis of wild reed was carried out at 500 °C. Waste fluidized catalytic cracking (FCC) catalyst disposed from a petroleum refinery process was activated through acetone-washing and calcination and used as catalyst for pyrolysis. In order to evaluate the catalytic activity of waste FCC catalyst, commercial HY zeolite catalyst with a SiO₂/Al₂O₃ ratio of 5.1 was also used. The bio-oil produced from pyrolysis was analyzed using gas chromatography/mass spectrometry (GC/MS). When the biomass-to-catalyst ratio was 1:1, the production of phenolics and aromatics was promoted considerably by catalysis, whereas the content of oxygenates was affected little. Significant conversion of oxygenates to furans and aromatics was observed when the biomass-to-catalyst ratio of 1:10 was used. Activated waste FCC catalyst showed comparable catalytic activity for biomass pyrolysis to HY in terms of the promotion of valuable chemicals, such as furans, phenolics and aromatics. The results of this study imply that waste FCC catalyst can be an important economical resource for producing high-value-added chemicals from biomass. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Graphical abstract

3950 KiB

Open AccessArticle

Shape Design of the Duct for Tidal Converters Using Both Numerical and Experimental Approaches (pre-2015)

by Chul H. Jo, Do Y. Kim, Su J. Hwang and Chan H. Goo

Energies 2016, 9(3), 185; https://doi.org/10.3390/en9030185 - 11 Mar 2016

Cited by 10 | Viewed by 4848

Abstract

Recently, focus has been placed on ocean energy resources because environmental concerns regarding the exploitation of hydrocarbons are increasing. Among the various ocean energy sources, tidal current power (TCP) is recognized as the most promising energy source in terms of predictability and reliability. [...] Read more.

Recently, focus has been placed on ocean energy resources because environmental concerns regarding the exploitation of hydrocarbons are increasing. Among the various ocean energy sources, tidal current power (TCP) is recognized as the most promising energy source in terms of predictability and reliability. The enormous energy potential in TCP fields has been exploited by installing TCP systems. The flow velocity is the most important factor for power estimation of a tidal current power system. The kinetic energy of the flow is proportional to the cube of the flow’s velocity, and velocity is a critical variable in the performance of the system. Since the duct can accelerate the flow velocity, its use could expand the applicable areas of tidal devices to relatively low velocity sites. The inclined angle of the duct and the shapes of inlet and outlet affect the acceleration rates of the flow inside the duct. In addition, the volume of the duct can affect the flow velocity amplification performance. To investigate the effects of parameters that increase the flow velocity, a series of simulations are performed using the commercial computational fluid dynamics (CFD) code ANSYS-CFX. Experimental investigations were conducted using a circulation water channel (CWC). Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

6489 KiB

Open AccessArticle

Francis Turbine Blade Design on the Basis of Port Area and Loss Analysis

by Zhenmu Chen, Patrick M. Singh and Young-Do Choi

Energies 2016, 9(3), 164; https://doi.org/10.3390/en9030164 - 4 Mar 2016

Cited by 16 | Viewed by 9807

Abstract

In this study, a Francis turbine with specific speed of 130 m-kW was designed on the basis of the port area and loss analysis. The meridional shape of the runner was designed focusing mainly on the combination of the guide vane loss analysis [...] Read more.

In this study, a Francis turbine with specific speed of 130 m-kW was designed on the basis of the port area and loss analysis. The meridional shape of the runner was designed focusing mainly on the combination of the guide vane loss analysis and experience. The runner blade inlet and outlet angles were designed by calculation of Euler’s head, while the port area of blade was modified by keeping constant angles of the blade at inlet and outlet. The results show that the effect of the port area of runner blade on the flow exit angle from runner passage is significant. A correct flow exit angle reduces the energy loss at the draft tube, thereby improving the efficiency of the turbine. The best efficiency of 92.6% is achieved by this method, which is also similar to the design conditions by the one dimension loss analysis. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

4677 KiB

Open AccessArticle

Analysis of the Potential for Use of Floating Photovoltaic Systems on Mine Pit Lakes: Case Study at the Ssangyong Open-Pit Limestone Mine in Korea

by Jinyoung Song and Yosoon Choi

Energies 2016, 9(2), 102; https://doi.org/10.3390/en9020102 - 10 Feb 2016

Cited by 104 | Viewed by 10875

Abstract

Recently, the mining industry has introduced renewable energy technologies to resolve power supply problems at mines operating in polar regions or other remote areas, and to foster substitute industries, able to benefit from abandoned sites of exhausted mines. However, little attention has been [...] Read more.

Recently, the mining industry has introduced renewable energy technologies to resolve power supply problems at mines operating in polar regions or other remote areas, and to foster substitute industries, able to benefit from abandoned sites of exhausted mines. However, little attention has been paid to the potential placement of floating photovoltaic (PV) systems operated on mine pit lakes because it was assumed that the topographic characteristics of open-pit mines are unsuitable for installing any type of PV systems. This study analyzed the potential of floating PV systems on a mine pit lake in Korea to break this misconception. Using a fish-eye lens camera and digital elevation models, a shading analysis was performed to identify the area suitable for installing a floating PV system. The layout of the floating PV system was designed in consideration of the optimal tilt angle and array spacing of the PV panels. The System Advisor Model (SAM) by National Renewable Energy Laboratory, USA, was used to conduct energy simulations based on weather data and the system design. The results indicated that the proposed PV system could generate 971.57 MWh/year. The economic analysis (accounting for discount rate and a 20-year operational lifetime) showed that the net present value would be $897,000 USD, and a payback period of about 12.3 years. Therefore, we could know that the economic effect of the floating PV system on the mine pit lake is relatively higher than that of PV systems in the other abandoned mines in Korea. The annual reduction of greenhouse gas emissions was analyzed and found to be 471.21 tCO₂/year, which is twice the reduction effect achieved by forest restoration of an abandoned mine site. The economic feasibility of a floating PV system on a pit lake of an abandoned mine was thus established, and may be considered an efficient reuse option for abandoned mines. Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

► Show Figures

Figure 1

Other

Jump to: Research

124 KiB

Open AccessErratum

Erratum: Shibata, S., et al. Reduced-Capacity Inrush Current Suppressor Using a Matrix Converter in a Wind Power Generation System with Squirrel-Cage Induction Machines. Energies 2016, 9, 223

by Sho Shibata, Hiroaki Yamada, Toshihiko Tanaka and Masayuki Okamoto

Energies 2017, 10(1), 146; https://doi.org/10.3390/en10010146 - 23 Jan 2017

Viewed by 3395

Abstract

n/a Full article

(This article belongs to the Special Issue Selected Papers from 5th Asia-Pacific Forum on Renewable Energy)

Journal Menu

Journal Browser

Selected Papers from 5th Asia-Pacific Forum on Renewable Energy

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Benefits of Publishing in a Special Issue

Published Papers (10 papers)

Research

Other

Further Information

Guidelines

MDPI Initiatives

Follow MDPI