Micromachines

Editorial

Jump to: Research

3 pages, 167 KiB

Open AccessEditorial

Editorial for the Special Issue on MEMS Mirrors

by Huikai Xie

Micromachines 2018, 9(3), 99; https://doi.org/10.3390/mi9030099 - 27 Feb 2018

Cited by 4 | Viewed by 4156

Abstract

MEMS mirrors can steer, modulate, and switch light, as well as control the wavefront for focusing or phase modulation.[...] Full article

(This article belongs to the Special Issue MEMS Mirrors)

Research

Jump to: Editorial

1082 KiB

Open AccessArticle

An Enhanced Robust Control Algorithm Based on CNF and ISM for the MEMS Micromirror against Input Saturation and Disturbance

by Jiazheng Tan, Weijie Sun and John T. W. Yeow

Micromachines 2017, 8(11), 326; https://doi.org/10.3390/mi8110326 - 3 Nov 2017

Cited by 13 | Viewed by 4160

Abstract

Input saturation is a widespread phenomenon in the field of instrumentation, and is harmful to performance and robustness. In this paper, a control design framework based on composite nonlinear feedback (CNF) and integral sliding mode (ISM) technique is proposed for a MEMS micromirror [...] Read more.

Input saturation is a widespread phenomenon in the field of instrumentation, and is harmful to performance and robustness. In this paper, a control design framework based on composite nonlinear feedback (CNF) and integral sliding mode (ISM) technique is proposed for a MEMS micromirror to improve its performance under input saturation. To make the framework more effective, some essential improvements are supplied. With the application of the proposed design framework, the micromirror under input saturation and time-varying disturbances can achieve precise positioning with satisfactory transient performance compared with the open-loop performance. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

3508 KiB

Open AccessArticle

Fabrication of Micro-Optics Elements with Arbitrary Surface Profiles Based on One-Step Maskless Grayscale Lithography

by Qinyuan Deng, Yong Yang, Hongtao Gao, Yi Zhou, Yu He and Song Hu

Micromachines 2017, 8(10), 314; https://doi.org/10.3390/mi8100314 - 23 Oct 2017

Cited by 43 | Viewed by 12609

Abstract

A maskless lithography method to realize the rapid and cost-effective fabrication of micro-optics elements with arbitrary surface profiles is reported. A digital micro-mirror device (DMD) is applied to flexibly modulate that the exposure dose according to the surface profile of the structure to [...] Read more.

A maskless lithography method to realize the rapid and cost-effective fabrication of micro-optics elements with arbitrary surface profiles is reported. A digital micro-mirror device (DMD) is applied to flexibly modulate that the exposure dose according to the surface profile of the structure to be fabricated. Due to the fact that not only the relationship between the grayscale levels of the DMD and the exposure dose on the surface of the photoresist, but also the dependence of the exposure depth on the exposure dose, deviate from a linear relationship arising from the DMD and photoresist, respectively, and cannot be systemically eliminated, complicated fabrication art and large fabrication error will results. A method of compensating the two nonlinear effects is proposed that can be used to accurately design the digital grayscale mask and ensure a precise control of the surface profile of the structure to be fabricated. To testify to the reliability of this approach, several typical array elements with a spherical surface, aspherical surface, and conic surface have been fabricated and tested. The root-mean-square (RMS) between the test and design value of the surface height is about 0.1 μm. The proposed method of compensating the nonlinear effect in maskless lithography can be directly used to control the grayscale levels of the DMD for fabricating the structure with an arbitrary surface profile. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

4672 KiB

Open AccessFeature PaperArticle

Modelling and Experimental Verification of Step Response Overshoot Removal in Electrothermally-Actuated MEMS Mirrors

by Mengyuan Li, Qiao Chen, Yabing Liu, Yingtao Ding and Huikai Xie

Micromachines 2017, 8(10), 289; https://doi.org/10.3390/mi8100289 - 25 Sep 2017

Cited by 14 | Viewed by 5683

Abstract

Micro-electro-mechanical system (MEMS) mirrors are widely used for optical modulation, attenuation, steering, switching and tracking. In most cases, MEMS mirrors are packaged in air, resulting in overshoot and ringing upon actuation. In this paper, an electrothermal bimorph MEMS mirror that does not generate [...] Read more.

Micro-electro-mechanical system (MEMS) mirrors are widely used for optical modulation, attenuation, steering, switching and tracking. In most cases, MEMS mirrors are packaged in air, resulting in overshoot and ringing upon actuation. In this paper, an electrothermal bimorph MEMS mirror that does not generate overshoot in step response, even operating in air, is reported. This is achieved by properly designing the thermal response time and the mechanical resonance without using any open-loop or closed-loop control. Electrothermal and thermomechanical lumped-element models are established. According to the analysis, when setting the product of the thermal response time and the fundamental resonance frequency to be greater than Q/2π, the mechanical overshoot and oscillation caused by a step signal can be eliminated effectively. This method is verified experimentally with fabricated electrothermal bimorph MEMS mirrors. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

3200 KiB

Open AccessArticle

Scanning Micro-Mirror with an Electrostatic Spring for Compensation of Hard-Spring Nonlinearity

by Takashi Izawa, Takashi Sasaki and Kazuhiro Hane

Micromachines 2017, 8(8), 240; https://doi.org/10.3390/mi8080240 - 4 Aug 2017

Cited by 20 | Viewed by 6494

Abstract

A scanning micro-mirror operated at the mechanical resonant frequency often suffer nonlinearity of the torsion-bar spring. The torsion-bar spring becomes harder than the linear spring with the increase of the rotation angle (hard-spring effect). The hard-spring effect of the torsion-bar spring generates several [...] Read more.

A scanning micro-mirror operated at the mechanical resonant frequency often suffer nonlinearity of the torsion-bar spring. The torsion-bar spring becomes harder than the linear spring with the increase of the rotation angle (hard-spring effect). The hard-spring effect of the torsion-bar spring generates several problems, such as hysteresis, frequency shift, and instability by oscillation jump. In this paper, a scanning micro-mirror with an electrostatic-comb spring is studied for compensation of the hard-spring effect of the torsion-bar spring. The hard-spring effect of the torsion-bar spring is compensated with the equivalent soft-spring effect of the electrostatic-comb spring. The oscillation curve becomes symmetric at the resonant frequency although the resonant frequency increases. Theoretical analysis is given for roughly explaining the compensation. A 0.5 mm square scanning micro-mirror having two kinds of combs, i.e., an actuator comb and a compensation comb, is fabricated from a silicon-on-insulator wafer for testing the compensation of the hard-spring in a vacuum and in atmospheric air. The bending of the oscillation curve is compensated by applying a DC voltage to the electrostatic-comb spring in vacuum and atmosphere. The compensation is attributed by theoretical approach to the soft-spring effect of the electrostatic-comb spring. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

11887 KiB

Open AccessArticle

Operation of a MOEMS Deformable Mirror in Cryo: Challenges and Results

by Frederic Zamkotsian, Patrick Lanzoni, Rudy Barette, Michael Helmbrecht, Franck Marchis and Alex Teichman

Micromachines 2017, 8(8), 233; https://doi.org/10.3390/mi8080233 - 27 Jul 2017

Cited by 14 | Viewed by 5807

Abstract

Micro-opto-electro-mechanical systems (MOEMS) Deformable Mirrors (DM) are key components for next generation optical instruments implementing innovative adaptive optics systems, both in existing telescopes and in the future ELTs. Characterizing these components well is critical for next generation instruments. This is done by interferometry, [...] Read more.

Micro-opto-electro-mechanical systems (MOEMS) Deformable Mirrors (DM) are key components for next generation optical instruments implementing innovative adaptive optics systems, both in existing telescopes and in the future ELTs. Characterizing these components well is critical for next generation instruments. This is done by interferometry, including surface quality measurement in static and dynamical modes, at ambient and in vacuum/cryo. We use a compact cryo-vacuum chamber designed for reaching 10–6 mbar and 160 K in front of our custom Michelson interferometer, which is able to measure performance of the DM at actuator/segment level and at the entire mirror level, with a lateral resolution of 2 µm and a sub-nanometer z-resolution. We tested the PTT 111 DM from Iris AO: an array of single crystalline silicon hexagonal mirrors with a pitch of 606 µm, able to move in tip, tilt, and piston (stroke 5–7 µm, tilt ±5 mrad). The device could be operated successfully from ambient to 160 K. An additional, mainly focus-like, 500 nm deformation of the entire mirror is measured at 160 K; we were able to recover the best flat in cryo by correcting the focus and local tip-tilts on all segments, reaching 12 nm rms. Finally, the goal of these studies is to test DMs in cryo and vacuum conditions as well as to improve their architecture for stable operation in harsh environments. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

5330 KiB

Open AccessArticle

PZT-Actuated and -Sensed Resonant Micromirrors with Large Scan Angles Applying Mechanical Leverage Amplification for Biaxial Scanning

by Shanshan Gu-Stoppel, Thorsten Giese, Hans-Joachim Quenzer, Ulrich Hofmann and Wolfgang Benecke

Micromachines 2017, 8(7), 215; https://doi.org/10.3390/mi8070215 - 6 Jul 2017

Cited by 22 | Viewed by 6477

Abstract

This article presents design, fabrication and characterization of lead zirconate titanate (PZT)-actuated micromirrors, which enable extremely large scan angle of up to 106° and high frequency of 45 kHz simultaneously. Besides the high driving torque delivered by PZT actuators, mechanical leverage amplification has [...] Read more.

This article presents design, fabrication and characterization of lead zirconate titanate (PZT)-actuated micromirrors, which enable extremely large scan angle of up to 106° and high frequency of 45 kHz simultaneously. Besides the high driving torque delivered by PZT actuators, mechanical leverage amplification has been applied for the micromirrors in this work to reach large displacements consuming low power. Additionally, fracture strength and failure behavior of poly-Si, which is the basic material of the micromirrors, have been studied to optimize the designs and prevent the device from breaking due to high mechanical stress. Since comparing to using biaxial micromirror, realization of biaxial scanning using two independent single-axial micromirrors shows considerable advantages, a setup combining two single-axial micromirrors for biaxial scanning and the results will also be presented in this work. Moreover, integrated piezoelectric position sensors are implemented within the micromirrors, based on which closed-loop control has been developed and studied. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

9745 KiB

Open AccessArticle

Design and Modeling of Polysilicon Electrothermal Actuators for a MEMS Mirror with Low Power Consumption

by Miguel Lara-Castro, Adrian Herrera-Amaya, Marco A. Escarola-Rosas, Moisés Vázquez-Toledo, Francisco López-Huerta, Luz A. Aguilera-Cortés and Agustín L. Herrera-May

Micromachines 2017, 8(7), 203; https://doi.org/10.3390/mi8070203 - 25 Jun 2017

Cited by 22 | Viewed by 9254

Abstract

Endoscopic optical-coherence tomography (OCT) systems require low cost mirrors with small footprint size, out-of-plane deflections and low bias voltage. These requirements can be achieved with electrothermal actuators based on microelectromechanical systems (MEMS). We present the design and modeling of polysilicon electrothermal actuators for [...] Read more.

Endoscopic optical-coherence tomography (OCT) systems require low cost mirrors with small footprint size, out-of-plane deflections and low bias voltage. These requirements can be achieved with electrothermal actuators based on microelectromechanical systems (MEMS). We present the design and modeling of polysilicon electrothermal actuators for a MEMS mirror (100 μm × 100 μm × 2.25 μm). These actuators are composed by two beam types (2.25 μm thickness) with different cross-section area, which are separated by 2 μm gap. The mirror and actuators are designed through the Sandia Ultra-planar Multi-level MEMS Technology V (SUMMiT V^®) process, obtaining a small footprint size (1028 μm × 1028 µm) for actuators of 550 µm length. The actuators have out-of-plane displacements caused by low dc voltages and without use material layers with distinct thermal expansion coefficients. The temperature behavior along the actuators is calculated through analytical models that include terms of heat energy generation, heat conduction and heat energy loss. The force method is used to predict the maximum out-of-plane displacements in the actuator tip as function of supplied voltage. Both analytical models, under steady-state conditions, employ the polysilicon resistivity as function of the temperature. The electrothermal-and structural behavior of the actuators is studied considering different beams dimensions (length and width) and dc bias voltages from 0.5 to 2.5 V. For 2.5 V, the actuator of 550 µm length reaches a maximum temperature, displacement and electrical power of 115 °C, 10.3 µm and 6.3 mW, respectively. The designed actuation mechanism can be useful for MEMS mirrors of different sizes with potential application in endoscopic OCT systems that require low power consumption. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Graphical abstract

5794 KiB

Open AccessFeature PaperArticle

An Electrostatic MEMS Translational Scanner with Large Out-of-Plane Stroke for Remote Axial-Scanning in Multi-Photon Microscopy

by Haijun Li, Xiyu Duan, Gaoming Li, Kenn R. Oldham and Thomas D. Wang

Micromachines 2017, 8(5), 159; https://doi.org/10.3390/mi8050159 - 15 May 2017

Cited by 18 | Viewed by 6431

Abstract

We present an electrostatic microelectromechanical systems (MEMS) resonant scanner with large out-of-plane translational stroke for fast axial-scanning in a multi-photon microscope system for real-time vertical cross-sectional imaging. The scanner has a compact footprint with dimensions of 2.1 mm × 2.1 mm × 0.44 [...] Read more.

We present an electrostatic microelectromechanical systems (MEMS) resonant scanner with large out-of-plane translational stroke for fast axial-scanning in a multi-photon microscope system for real-time vertical cross-sectional imaging. The scanner has a compact footprint with dimensions of 2.1 mm × 2.1 mm × 0.44 mm, and employs a novel lever-based compliant mechanism to enable large vertical displacements of a reflective mirror with slight tilt angles. Test results show that by using parametrical resonance, the scanner can provide a fast out-of-plane translational motion with ≥400 μm displacement and ≤0.14° tilt angle over a wide frequency range of ~390 Hz at ambient pressure. By employing this MEMS translational scanner and a biaxial MEMS mirror for lateral scanning, vertical cross-sectional imaging with a beam axial-scanning range of 200 μm and a frame rate of ~5–10 Hz is enabled in a remote scan multi-photon fluorescence imaging system. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

9305 KiB

Open AccessFeature PaperArticle

Design and Fabrication of a 2-Axis Electrothermal MEMS Micro-Scanner for Optical Coherence Tomography

by Quentin A. A. Tanguy, Sylwester Bargiel, Huikai Xie, Nicolas Passilly, Magali Barthès, Olivier Gaiffe, Jaroslaw Rutkowski, Philippe Lutz and Christophe Gorecki

Micromachines 2017, 8(5), 146; https://doi.org/10.3390/mi8050146 - 5 May 2017

Cited by 25 | Viewed by 8598

Abstract

This paper introduces an optical 2-axis Micro Electro-Mechanical System (MEMS) micromirror actuated by a pair of electrothermal actuators and a set of passive torsion bars. The actuated element is a dual-reflective circular mirror plate of 1

m m

in diameter. This inner mirror [...] Read more.

This paper introduces an optical 2-axis Micro Electro-Mechanical System (MEMS) micromirror actuated by a pair of electrothermal actuators and a set of passive torsion bars. The actuated element is a dual-reflective circular mirror plate of 1

m m

in diameter. This inner mirror plate is connected to a rigid frame via a pair of torsion bars in two diametrically opposite ends located on the rotation axis. A pair of electrothermal bimorphs generates a force onto the perpendicular free ends of the mirror plate in the same angular direction. An array of electrothermal bimorph cantilevers deflects the rigid frame around a working angle of 45

^{\circ}

for side-view scan. The performed scans reach large mechanical angles of 32

^{\circ}

for the frame and 22

^{\circ}

for the in-frame mirror. We denote three resonant main modes, pure flexion of the frame at 205

Hz

, a pure torsion of the mirror plate at 1.286

kHz

and coupled mode of combined flexion and torsion at 1.588

kHz

. The micro device was fabricated through successive stacks of materials onto a silicon-on-insulator wafer and the patterned deposition on the back-side of the dual-reflective mirror is achieved through a dry film photoresist photolithography process. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

3093 KiB

Open AccessArticle

A Large-Size MEMS Scanning Mirror for Speckle Reduction Application

by Fanya Li, Peng Zhou, Tingting Wang, Jiahui He, Huijun Yu and Wenjiang Shen

Micromachines 2017, 8(5), 140; https://doi.org/10.3390/mi8050140 - 3 May 2017

Cited by 27 | Viewed by 7003

Abstract

Based on microelectronic mechanical system (MEMS) processing, a large-size 2-D scanning mirror (6.5 mm in diameter) driven by electromagnetic force was designed and implemented in this paper. We fabricated the micromirror with a silicon wafer and selectively electroplated Ni film on the back [...] Read more.

Based on microelectronic mechanical system (MEMS) processing, a large-size 2-D scanning mirror (6.5 mm in diameter) driven by electromagnetic force was designed and implemented in this paper. We fabricated the micromirror with a silicon wafer and selectively electroplated Ni film on the back of the mirror. The nickel film was magnetized in the magnetic field produced by external current coils, and created the force to drive the mirror’s angular deflection. This electromagnetically actuated micromirror effectively eliminates the ohmic heat and power loss on the mirror plate, which always occurs in the other types of electromagnetic micromirrors with the coil on the mirror plate. The resonant frequency for the scanning mirror is 674 Hz along the slow axis, and 1870 Hz along the fast axis. Furthermore, the scanning angles could achieve ±4.5° for the slow axis with 13.2 mW power consumption, and ±7.6° for the fast axis with 43.3 mW power consumption. The application of the MEMS mirror to a laser display system effectively reduces the laser speckle. With 2-D scanning of the MEMS mirror, the speckle contrast can be reduced from 18.19% to 4.58%. We demonstrated that the image quality of a laser display system could be greatly improved by the MEMS mirror. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Graphical abstract

3274 KiB

Open AccessArticle

Modeling of MEMS Mirrors Actuated by Phase-Change Mechanism

by David Torres, Jun Zhang, Sarah Dooley, Xiaobo Tan and Nelson Sepúlveda

Micromachines 2017, 8(5), 138; https://doi.org/10.3390/mi8050138 - 26 Apr 2017

Cited by 7 | Viewed by 5964

Abstract

Given the multiple applications for micro-electro-mechanical system (MEMS) mirror devices, most of the research efforts are focused on improving device performance in terms of tilting angles, speed, and their integration into larger arrays or systems. The modeling of these devices is crucial for [...] Read more.

Given the multiple applications for micro-electro-mechanical system (MEMS) mirror devices, most of the research efforts are focused on improving device performance in terms of tilting angles, speed, and their integration into larger arrays or systems. The modeling of these devices is crucial for enabling a platform, in particular, by allowing for the future control of such devices. In this paper, we present the modeling of a MEMS mirror structure with four actuators driven by the phase-change of a thin film. The complexity of the device structure and the nonlinear behavior of the actuation mechanism allow for a comprehensive study that encompasses simpler electrothermal designs, thus presenting a general approach that can be adapted to most MEMS mirror designs based on this operation principle. The MEMS mirrors presented in this work are actuated by Joule heating and tested using optical techniques. Mechanical and thermal models including both pitch and roll displacements are developed by combining theoretical analysis (using both numerical and analytical tools) with experimental data and subsequently verifying with quasi-static and dynamic experiments. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

4274 KiB

Open AccessArticle

In-Plane Optical Beam Collimation Using a Three-Dimensional Curved MEMS Mirror

by Yasser M. Sabry, Diaa Khalil, Bassam Saadany and Tarik Bourouina

Micromachines 2017, 8(5), 134; https://doi.org/10.3390/mi8050134 - 25 Apr 2017

Cited by 12 | Viewed by 6879

Abstract

The collimation of free-space light propagating in-plane with respect to the substrate is an important performance factor in optical microelectromechanical systems (MEMS). This is usually carried out by integrating micro lenses into the system, which increases the cost of fabrication/assembly in addition to [...] Read more.

The collimation of free-space light propagating in-plane with respect to the substrate is an important performance factor in optical microelectromechanical systems (MEMS). This is usually carried out by integrating micro lenses into the system, which increases the cost of fabrication/assembly in addition to limiting the wavelength working range of the system imposed by the dispersion characteristic of the lenses. In this work we demonstrate optical fiber light collimation using a silicon micromachined three-dimensional curved mirror. Sensitivity to micromachining and fiber alignment tolerance is shown to be low enough by restricting the ratio between the mirror focal length and the optical beam Rayleigh range below 5. The three-dimensional curvature of the mirror is designed to be astigmatic and controlled by a process combining deep, reactive ion etching and isotropic etching of silicon. The effect of the micromachining surface roughness on the collimated beam profile is investigated using a Fourier optics approach for different values of root-mean-squared (RMS) roughness and correlation length. The isotropic etching step of the structure is characterized and optimized for the optical-grade surface requirement. The experimental optical results show a beam-waist ratio of about 4.25 and a corresponding 12-dB improvement in diffraction loss, in good agreement with theory. This type of micromirror can be monolithically integrated into lensless microoptoelectromechanical systems (MOEMS), improving their performance in many different applications. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

10567 KiB

Open AccessArticle

The Exploration for an Appropriate Vacuum Level for Performance Enhancement of a Comb-Drive Microscanner

by Rong Zhao, Dayong Qiao, Xiumin Song and Qiaoming You

Micromachines 2017, 8(4), 126; https://doi.org/10.3390/mi8040126 - 16 Apr 2017

Cited by 8 | Viewed by 5159

Abstract

In order to identify the influence of the vacuum environment on the performance of a comb-drive microscanner, and indicate the optimum pressure for enhancing its performance, a comb-drive microscanner fabricated on silicon-on-insulator (SOI) substrate was prepared and tested at different pressures, and the [...] Read more.

In order to identify the influence of the vacuum environment on the performance of a comb-drive microscanner, and indicate the optimum pressure for enhancing its performance, a comb-drive microscanner fabricated on silicon-on-insulator (SOI) substrate was prepared and tested at different pressures, and the characteristics in vacuum were obtained. The test results revealed that the vacuum environment enhanced the performance in the optical scanning angle, and decreased the actuation voltage. With a 30 V driving voltage applied, the microscanner can reach an optical scanning angle of 44.3° at a pressure of 500 Pa. To obtain an enhancement in its properties, only a vacuum range from 100 to 1000 Pa is needed, which can be very readily and economically realized and maintained in a vacuum package. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

5736 KiB

Open AccessArticle

Large-Aperture kHz Operating Frequency Ti-alloy Based Optical Micro Scanning Mirror for LiDAR Application

by Liangchen Ye, Gaofei Zhang and Zheng You

Micromachines 2017, 8(4), 120; https://doi.org/10.3390/mi8040120 - 10 Apr 2017

Cited by 54 | Viewed by 13015

Abstract

A micro scanning mirror is an optical device used to scan laser beams which can be used for Light Detection and Ranging (LiDAR) in applications like unmanned driving or Unmanned Aerial Vehicle (UAV). The MEMS scanning mirror’s light-weight and low-power make it a [...] Read more.

A micro scanning mirror is an optical device used to scan laser beams which can be used for Light Detection and Ranging (LiDAR) in applications like unmanned driving or Unmanned Aerial Vehicle (UAV). The MEMS scanning mirror’s light-weight and low-power make it a useful device in LiDAR applications. However, the MEMS scanning mirror’s small aperture limits its application because it is too small to deflect faint receiving light. In this paper, we present a Ti-alloy-based electromagnetic micro scanning mirror with very large-aperture (12 mm) and rapid scanning frequency (1.24 kHz). The size of micro-scanner’s mirror plate reached 12 mm, which is much larger than familiar MEMS scanning mirror. The scanner is designed using MEMS design method and fabricated by electro-sparking manufacture method. As the experimental results show, the resonant frequency of the micro scanning mirror is 1240 Hz and the optical scanning angle can reach 26 degrees at resonance frequency when the actuation current is 250 mApp. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

8221 KiB

Open AccessArticle

Multi-Response Optimization of Electrothermal Micromirror Using Desirability Function-Based Response Surface Methodology

by Muhammad Mubasher Saleem, Umar Farooq, Umer Izhar and Umar Shahbaz Khan

Micromachines 2017, 8(4), 107; https://doi.org/10.3390/mi8040107 - 1 Apr 2017

Cited by 7 | Viewed by 6924

Abstract

The design of a micromirror for biomedical applications requires multiple output responses to be optimized, given a set of performance parameters and constraints. This paper presents the parametric design optimization of an electrothermally actuated micromirror for the deflection angle, input power, and micromirror [...] Read more.

The design of a micromirror for biomedical applications requires multiple output responses to be optimized, given a set of performance parameters and constraints. This paper presents the parametric design optimization of an electrothermally actuated micromirror for the deflection angle, input power, and micromirror temperature rise from the ambient for Optical Coherence Tomography (OCT) system. Initially, a screening design matrix based on the Design of Experiments (DOE) technique is developed and the corresponding output responses are obtained using coupled structural-thermal-electric Finite Element Modeling (FEM). The interaction between the significant design factors is analyzed by developing Response Surface Models (RSM) for the output responses. The output responses are optimized by combining the individual responses into a composite function using desirability function approach. A downhill simplex method, based on the heuristic search algorithm, is implemented on the RSM models to find the optimal levels of the design factors. The predicted values of output responses obtained using multi-response optimization are verified by the FEM simulations. Full article

(This article belongs to the Special Issue MEMS Mirrors)

► Show Figures

Figure 1

Journal Menu

Journal Browser

MEMS Mirrors

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Benefits of Publishing in a Special Issue

Published Papers (16 papers)

Editorial

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI