Current Research, Trends, and Prospects in Laser-Assisted Additive Printing Technology
A special issue of Photonics (ISSN 2304-6732). This special issue belongs to the section "Lasers, Light Sources and Sensors".
Deadline for manuscript submissions: 31 December 2024 | Viewed by 254
Special Issue Editors
Interests: laser-induced forward transfer (LIFT); laser processing; thin films; surface structuring
Interests: laser-induced forward transfer (LIFT); laser processing; thin films; surface structuring
Special Issues, Collections and Topics in MDPI journals
Special Issue Information
Dear Colleagues,
We are currently running a Special Issue of MDPI's journal Photonics. As Guest Editors, we cordially invite you to submit a manuscript for consideration and possible publication in this Special Issue, entitled "Current Research, Trends, and Prospects in Laser-Assisted Additive Printing Technology".
The aim of this Special Issue is to cover relevant experimental and theoretical aspects from new technologies in this field to their applications, via the following topics:
- Laser-assisted additive printing technologies;
- Bio-printing for tissue engineering, scaffolding, and surface structuring for bioapplications;
- Additive fabrication of biosensors, synthetic biostructures, implants, and biodevices;
- Additive microfabrication in microelectronics, optoelectronics, flexible electronics, and organic electronics;
- Additive fabrication in electrical engineering (including radiofrequency and microwave engineering, photovoltaic cells and batteries, electrochemistry, etc.);
- Micro-/nano-additive structuring via nanophotonics for metallic, ceramic, and glass materials;
- Theoretical aspects of laser-assisted additive printing technologies: modeling/simulation research.
Consequently, this Special Issue welcomes original research and review manuscripts on challenges and trends covering fundamental and experimental research on laser-assisted additive printing technologies and applications, with special emphasis for environmental protection technology, ecology and ecological applications, and ecological science, to address the current environmental problems.
The Special Issue is in cooperation with the "Laserlab-Europe Training Event" (further details are provided below). Scholars who contribute articles to this Special Issue following their participation in the event are eligible for a 20% reduction in the Article Processing Charge.
Laserlab-Europe Training Event
Laserlab-Europe organizes a training event on laser-induced printing for microscale additive fabrication at the Laser Plasma and Photonic Processes Laboratory (LP3 UMR 7341 CNRS AMU) on the Campus of Luminy, Marseille (France). The next event will be held on the 09/10/2024 and later on demand.
The lab experiments will be held on one of the LP3 platforms (LaMP, https://lp3.fr/les-plateformes/lamp/) focused on the development and industrial transfer of laser-based processes.
Attendance is limited to a maximum of four participants. A limited number of bursaries are available from Laserlab-Europe to cover the registration fee, travel, and accommodation costs.
How to apply: please contact the LP3 staff in charge of the training—Dr. Anne-Patricia Alloncle and Dr. Catalin-Daniel Constantinescu.
Further information is available on the following link: https://www.laserlab-europe.eu/events/laserlab-events/2024/training-laser-induced-printing-for-microscale-additive-fabrication-lp3.
Dr. Anne-Patricia Alloncle
Dr. Catalin-Daniel Constantinescu
Guest Editors
Manuscript Submission Information
Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.
Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Photonics is an international peer-reviewed open access monthly journal published by MDPI.
Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2400 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.
Keywords
- laser-assisted additive printing technology
- laser-assisted bio-printing
- laser-induced forward transfer
- additive microfabrication
- micro-/nano-additive structuring
Benefits of Publishing in a Special Issue
- Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
- Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
- Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
- External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
- e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.
Further information on MDPI's Special Issue polices can be found here.
