1. Introduction
Floods are major threats to lives and properties in vulnerable areas of Thailand, especially in many provinces in the Central and Northern Plains, and Northeast regions. As stated by [
1], the most common cause of floods in Thailand is heavy monsoon rains and tropical storms, which tend to be more disastrous, frequent and costly, and threaten the nation as a whole.
In 2011, Thailand encountered with the worst flood crisis in 70 years [
2], with the largest annual rainfall over Thailand among the nation’s 61-year rainfall record [
3]. More details were added by [
4], who observed that the 2011 Thailand floods were mainly caused by a strong Southeast Asian summer monsoon which brought extraordinary rainfall over the country between May to October, whilst the remaining four tropical storms produced high rainfall to northern Thailand between June and October. The incoming rainfall rate was significantly higher than the controlled releases from dams, of which most dams were almost full by the beginning of October 2011 [
5]. During the most critical flood period (October through November 2011), the drainage capacity of rivers was exceeded and resulted in water overflowing the riverbank and encroaching the broad, low-lying surrounding floodplain where agricultural, industrial, and urban development existed. As a result, 65 out of 77 provinces were declared to be flood disaster zones with more than 800 deaths and an estimated extensive economic damage of US
$46.5 billion, in which the manufacturing sector bore approximately 70 percent of the total damage and losses due to the flooding of six industrial estates in Ayuthaya and Pathum Thani [
6].
The signs of the aforementioned flood incidents are clearly visible and linked to the impacts of climate and land use changes on hydrological responses. Therefore, several studies were conducted to investigate whether there was evidence of such potential impacts on flood consequences, especially in Northeast Thailand. The study of [
7] revealed that climate and land use changes have a direct impact on runoff in the lower Lam Pao River Basin (situated in Northeast Thailand). In detail, based on the PRECIS Regional Climate Model outputs, the average rainfall will be increased by 14.5 mm, whereas the average daily maximum and minimum temperature will be increased between 1.8 °C to 2.6 °C, respectively, in the next 50 years (2016–2065). In addition, by applying the Soil and Water Assessment Tool (SWAT) model in association with the projection of climate and land use change, the study also found that when changing paddy fields to crops and urban area by 20, 40, 60, 80, and 100 percent increments, the average annual runoff will be lower than the baseline (2006–2015) by 16.6% to 35.0%, while the average runoff will be higher than the baseline by 13.4% during the years 2012–2021. The evaluation was also made by [
8] for assessing the impacts of climate and land use changes on river discharge in the Lam Chi sub-watershed in Northeast Thailand by using the global hydrological model, the H08 model, the climate data from the Coupled Model Intercomparison Project Phase 5 (CMIP5) for the period 2022–2031, and land use data projected by the Conversion of Land Use and its Effects (CLUE) model. It was found that the discharges will increase due to increases in precipitation between the past (1986–1995) and future (2022–2031). Due to differences in soil depth, the subsurface flow rate, and evapotranspiration, the discharge in the forested area is expected to be lower than in the agricultural area. Lastly, the study also indicated that the impact on the progression of current to future discharge due to land use change is smaller than climate change, whereas the opposite was observed for the transition from the historical to more recent past.
Regarding the climate change issue, the research in [
9] was carried out to assess the flood hazard potential under climate change scenarios in the Yang River Basin, Northeast Thailand. Through the applications of hydrological model TOPMODEL and Hydrologic Engineering Center’s River Analysis System (HEC-RAS) hydraulic model, the simulations of floods under future climate scenarios for the periods 2010–2039 (2020s), 2040–2069 (2050s), and 2070–2099 (2080s), were performed. It was found that, in the future, the Yang River Basin will get warmer and wetter, whereas both the minimum and maximum temperature is also projected to increase. Likewise, the average annual rainfall is also projected to be higher in the near future and lower in the far future. In addition, the expected intensity of annual floods is found to be increased for both Representative Concentration Pathway (RCP) 4.5 and 8.5 scenarios, in which the generated flood inundation map under 100-year return period is found to be larger than the baseline flood inundation map (1980–2009) by approximately 60 km
2. The impact of climate change on flood events in the Nippersink Creek watershed located in Northeastern Illinois was also assessed by [
10], in which the Hydrologic Engineering Center’s Hydrologic Modeling System (HEC-HMS) was applied to model the hydrologic processes based on meteorological inputs from the CMIP5 general circulation models. It was found that the increase in greenhouse gas concentration (under RCP 8.5 scenario) can increase the future precipitation, as well as induce a greater impact on flood events (by the 110% increase from the historically-observed 100-year flood). The study performed by [
11] examined the impact of climate change on the hydrological behavior of the Jhelum River basin, in which the bias-corrected CMIP5 data from four GCMs (BCC-CSM1.1, INMCM4, IPSL-CM5A-LR, and CMCCCMS) and two emissions scenarios (RCP 4.5 and RCP 8.5) were used to drive the calibrated the Hydrological Modeling System (HEC-HMS) and the Snowmelt Runoff Model (SRM) for the simulation of projected streamflow. The results revealed that the precipitation (increasing by 183.2 mm or 12.74%) during the monsoon for RCP 4.5 and the rise in temperature (increase in T
min and T
max will be 4.77 °C and 4.42 °C, respectively) during the pre-monsoon period for RCP 8.5 during the 2090s will lead to an increase in snowmelt-runoff of up to 48%, evapotranspiration and soil water storage of up to 45%, streamflow by 330 m
3/s (22.6%) (calculated by HEC-HMS) and 449 m
3/s (30.7%) (estimated by SRM).
In view of the land use change, relevant research was undertaken by [
12] to investigate the influences of land management and conservation practices on discharge and sediment yield for providing alternatives to the current watershed management practices in the Chi River Sub-basin Part II, in Northeast Thailand. Three land management scenarios, i.e., 1) current land use with conservation practices, 2) Land Use Planning (LUP) based on Watershed Classification (WSC), and 3) WSC with conservation practices, were simulated with the SWAT model, and the obtained results were compared with the existing conditions. Based on the simulation results, the current land use with conservation practices (scenario 1) would result in a slight decrease in both total discharge and sediment yield. Under scenario 2, WSC would result in a small decrease in discharge, but a dramatic increase in sedimentation. Referring to scenario 3, WSC together with conservation practices would result in a slight decrease in discharge and a small increase in sedimentation.
Furthermore, there are a lot more studies which are relevant to the potential impacts of climate change and anthropogenic land management activities on hydrologic responses in Northeast Thailand such as [
13,
14,
15,
16,
17]. In brief, the abovementioned studies showed a corresponding trend towards climate and land use change, which can worsen and trigger an increase in both the magnitude and frequency of extreme flood events and could directly pose a great threat to human well-being and economic development. However, the quantification of expected flood damage in monetary terms was not quantitatively evaluated in the aforementioned studies [
7,
8,
9,
12,
13,
14,
15,
16,
17], as they opted to focus more on flow regime (i.e., magnitude, frequency) or flood characteristics (i.e., depth of inundation, duration, and area inundated). To close the knowledge gap, this study aimed to quantify the impacts of climate and land use changes on flood damage (on both a monetary basis and a threat basis, i.e., flood depth, duration, and extent) at different levels of recurrence. A case study of the lower Nam Phong River Basin, situated in Northeast Thailand, which frequently experiences floods which tend to be more severe due to substantial land use alteration and future climate change, was conducted to get a detailed insight into the possible impacts. Above all, the main findings of this study will be helpful to properly formulate adaptation strategies and withstand the adverse impacts of possible future flood risks and damage due to climate and land use changes in the lower Nam Phong River Basin and other areas throughout Thailand.
2. Materials and Methods
2.1. Study Area
The study focused on the lower Nam Phong River Basin, which is located in the Northeastern region of Thailand, with a total area of approximately 2386 km
2, whereas the topography is undulating, varying in elevation from 139 m to 623 m above mean sea level (m+MSL) (note: since the Huai Sai Bat River is a main tributary of the Nam Phong River, the Huai Sai Bat sub-basin is then considered and included in this study, resulting in a larger study area of approximately 3127 km
2). The Nam Phong River is considered to be the main river in the Nam Phong River Basin with a length of about 136 km that extends from the Ubol Ratana Dam (receiving the water from Lam Phaniang, Nam Phuai, Upper Lam Nam Phong, Lam Nam Choen, and Nam Phrom sub-basins with the storage capacity of 2431 million m
3 (MCM)) at the upstream end to the Chi River at the downstream end (
Figure 1). The climate in the river basin is typically dominated by monsoon winds, i.e., the Northeast monsoon brings cool and dry weather during November to February. A dry season prevails from March to May. After this, the wet season is characterized by the Southwest monsoon that lasts from June to October. The average annual temperature is 26.8 °C, ranging from about 16.7 °C in December to about 36.4 °C in April. The average relative humidity, for the year as a whole, is about 71.1%, in which the month with the highest relative humidity is September (82.5%) and the lowest is March (60%). The mean annual rainfall is approximately 1237.6 mm/year, whilst the month with most rainfall is September (224.9 mm) and the least is in January (2.1 mm) [
18]. The mean annual discharge is about 1594.9 MCM/year with a minimum discharge of 34.5 MCM/year (in February) and a maximum discharge of 366.0 MCM/year (in October) [
19].
2.2. Data Collection
The data collected for this study consists of 2 parts, which are 1) hydro-meteorological data, and 2) physical data of the river basin. Regarding the hydro-meteorological data, long-term daily datasets were collected from 24 rainfall stations of the Thai Meteorological Department (during 2000–2017), the E.22B gauging station (situated at Ban Tha Mao, Nam Phong District, Khon Kaen Province) of the Royal Irrigation Department (during 2005–2017), and the Ubol Ratana reservoir inflow hydrograph of the Electricity Generating Authority of Thailand (during 2005–2017) (see
Figure 1 for locations of gauging stations). The physical river basin data such as the Digital Elevation Model (DEM, 5 m × 5 m grid spacing with vertical accuracies of 2 m for slope less than 35% and 4 m for slope greater than 35% [
20]), land use, and soils were obtained from the Land Development Department (LDD). Other than that, the 2009 bathymetric surveys of 113 river cross sections at almost every 1 km along a 136 km reach of the Nam Phong River was also retrieved from the Research Center for Environmental and Hazardous Substance Management, Khon Kaen University.
2.3. GCMs, RCP Climate Scenarios, and Bias Correction
2.3.1. Representative Concentration Pathways (RCPs) Scenarios with Global Climate Models (GCMs) for South Asia (CORDEX-SA)
The analysis of future rainfall changes was used for the analysis of future streamflow calculated by the Hydrologic Engineering Center’s Hydrologic Modeling System (HEC-HMS) model. In this study, three sets of simulations were driven by the following three GCMs viz., CNRM-CM5, IPSL-CM5A-MR, and MPI-ESM-LR, for the future climate projections (see
Table 1 for more details). Based on the model performance of historical runs, the downscaled future climate data was derived from the Regional Climate Model (RCM) with 50 km grid spacing under the influence of Representative Concentration Pathways (RCPs) 4.5 and 8.5 emission scenarios, from the Coordinated Regional Climate Downscaling Experiment over the South Asia Domain (CORDEX-SA) (note: RCP 4.5 represents a stable scenario where the radiative force will reach up to 4.5 W/m
2 by 2100) [
21,
22,
23,
24]. RCP 8.5 represents a relatively extreme scenario where greenhouse gas (GHG) will continuously increase throughout 2100, at which time radiative force will reach 8.5 W/m² [
25,
26].
2.3.2. Bias Correction
The RCMs seem to be able to provide a higher spatial resolution and more reliable results on a regional scale in comparison to General Circulation Models (GCMs), as they can produce more spatially and physically coherent outputs with observations [
27,
28,
29]. Nevertheless, the original RCM outputs still contain considerable bias due to the forcing of GCMs, or from systematic model errors, in which such biases could be amplified during climate change impact studies [
30,
31]. Therefore, the bias correction of RCM simulated data is of great importance and is a prerequisite step for data correction prior to climate change effect analysis. As such, the bias correction by the Linear Scaling method included in the tailor-made tool dubbed the “Climate Model data for hydrologic modeling (CMhyd)” was used for bias-correcting climate variables obtained from RCMs [
32]. The RCMs simulated historical rainfall during the period of 1989–2005, which was calibrated with the historical observed rainfall during the same period, and projected rainfall for the period 2020–2039 under two RCPs (RCP 4.5 and RCP 8.5) (see
Figure 2 for detailed bias correction procedure).
2.4. Analysis of Future Land Use Change
The analysis of future streamflow is based on the simulation results performed by HEC-HMS model, in which a parameter related to future land use would also need to be imported into the model for representing future runoff generation processes. In this study, the Land Change Modeler (LCM) tool, which is the extension of TerrSet software developed by Clark Lab [
33], was used to analyze the spatial pattern of changes in predicting the Land Use and Land Cover (LULC) and validating the predicted LULC outputs [
34]. A combination of Multi-Layer Perceptron (MLP) and Markov chain analysis was applied to model the transition and projection of historical (2010), present (2015), and future (2039) land use maps. The MLP, which is a feed-forward artificial neural network that generates a set of outputs from a set of inputs with separate training and recall phases [
35], was trained to model land use transitions through creating transition maps. The transition potential maps created using MLP are based on a set of explanatory variables called drivers, i.e., agricultural areas, distance to urban areas, rivers, roads, as well as altitude, slope, and aspect of land. The land use modeling requires the integration of both changes in environmental and socio-economic drivers, however, the incorporation of the socio-economic factor is restricted by the lack of spatial data and the difficulties in integration with other environmental data [
36]. The Markov chain method was also applied with sufficient accuracy to process the transition maps for the prediction process [
37], based on the past trends of the land use changes from the period 2010 to 2015.
2.5. Hydrological Modeling
The estimation of streamflow in the Nam Phong River Basin was carried out using HEC-HMS model, which is designed for rainfall-runoff processes based on the relationships among runoff, evapotranspiration, infiltration, excess rainfall transformation, baseflow, and open channel routing of both gauged and ungauged river basins. In principle, the HEC-HMS program is a modeling system, which relies on dividing the hydrologic cycle into separate pieces, constructing watershed boundaries, and representing each water cycle component by a separate mathematical model. As a result, each mathematical model becomes suitable for different environments and conditions [
38].
The HEC-HMS simulation results is stored in the HEC-DSS (Hydrologic Engineering Center’s Data Storage System), which can be used in conjunction with other HEC software, like Hydrologic Engineering Center’s River Analysis System (HEC-RAS), for water availability, urban drainage, flow forecasting, future urbanization impact, reservoir spillway design, flood damage reduction, floodplain regulation, and systems operation. More details on the process of HEC-HMS model construction are presented as follows.
2.5.1. Watershed Delineation
As a prerequisite to the HEC-HMS model set-up, the watershed was delineated and divided into several sub-basins using Arc Hydro Tools in ArcGIS 10.3 software, based on the 30-m Digital Elevation Model (DEM) and stream network. In consequence, the entire study area was then divided into 25 sub-basins consisting of 5 sub-basins for the upper Nam Phong River Basin (covering the areas upstream of the Ubol Ratana reservoir) and 20 sub-basins for the Lower Nam Phong River Basins (covering the areas downstream of the Ubol Ratana reservoir) (see more details in
Figure 3).
2.5.2. HEC-HMS Hydrologic Elements
The HEC-HMS hydrologic elements, such as sub-basin, reach, junction, reservoir, diversion, source, and sink, are thoroughly connected in the river network, where their connectivity is considered to represent the runoff processes and their effects on the drainage system [
38]. In this study, the Nam Phong model set-up contains only 5 of the abovementioned elements, accounting for in total 93 hydrologic elements. In detail, there are 25 sub-basin elements connected with 45 reaches and 22 junctions. In addition, five reservoir elements were also assigned to model the detention and attenuation of hydrographs caused by Ubol Ratana, Kaeng Sua Ten, Huai Siew, and Nong Loeng Yai Reservoirs, including Nong Wai Operation and Maintenance Project (Nong Wai Weir). A diversion element was also added to model the diverted flow from Nong Wai Weir to the left and right main irrigation canals.
2.5.3. Importing HEC-HMS Input Parameters
To estimate the water balance components, the following computation models were applied to the sub-basins and reaches in which their detailed descriptions can be described below.
Runoff-volume models are used to compute the runoff volume of sub-basins by subtracting the rainfall by losses through interception, surface storage, infiltration, evaporation, and transpiration. In this study, the “Initial and constant rate model” was selected and used as sub-basin loss method for sub-basins within the Nam Phong River Basin.
Direct-runoff models are used to convert excess rainfall into direct runoff at the outlets of each sub-basin. The “Snyder unit hydrograph model”, which is a synthetic unit hydrograph method developed to compute the peak flow as a unit of rainfall, was used in this study (note: a unit hydrograph represents the runoff distribution over time for one unit of rainfall excess over the entire watershed for a specified duration).
Baseflow models are proposed to simulate the slow subsurface water drainage from the system into the channels, in which the “Exponential recession model” was chosen for this study.
Routing models are employed to simulate one-dimensional open channel flow for determining the flow hydrograph at the downstream point of the sub-basin in relation to its upstream reach, and functions of sub-basin characteristics, such as slope and length of channel, channel roughness, channel shape, downstream control, and initial flow condition [
39]. In this study, the “Muskingum model” was selected.
2.5.4. Importing Rainfall Data
The daily rainfall time-series during the period 2000–2017, collected from 24 selected weather stations of the Thai Meteorological Department (TMD) located within and surrounding the Nam Phong River Basin, was used in this study (see
Figure 3 for rainfall station locations). Before importing rainfall data into the HEC-HMS model, the adjustment of point rainfall to areal rainfall distribution was made using the Thiessen Polygon Method, which is a standard method for computing mean areal rainfall for the topographical and meteorological homogeneous areas (see Equation (1) for formula used).
where
—the mean areal rainfall
—rainfall observed at the ith station inside or outside the Nam Phong River Basin
—in-region portion of the area of the polygon surrounding the ith station (area of each polygon)
—the total area of the Nam Phong River Basin
—the number of areas
2.6. Frequency Analysis
Frequency analysis was used to estimate the time interval between similar size/intensity of events or the so-called return period of specific events. The frequently used probability function, i.e., Gumbel distribution, was used to estimate the probable (maximum daily and annual) rainfall in the Nam Phong River Basin for different return periods. The time horizon of 38 years was divided into periods of different lengths, i.e., the years 2000–2017 (baseline) and 2020–2039 (future). The RCM projected maximum daily rainfall for the period 2020–2039 was estimated for given return periods, i.e., 25-, 50-, and 100-year periods, based on a frequency–factor formulation of the Gumbel distribution (see
Section 2.3.2 for details).
2.7. Hydraulic Modeling
The HEC-RAS hydraulic model, developed by the Hydrologic Engineering Center (HEC) of the U.S. Army Corps of Engineers, was used for flow and flood analysis under different discharge conditions in the river system of the Nam Phong River Basin, since the HEC-RAS set-up is capable of performing 1D steady state water surface profile calculations, as well as unsteady 1D and 2D flow simulations [
40]. The water surface profiles are calculated from the previous cross section to the next one by solving the energy equation (Equation (2)) with an iterative procedure: the so-called standard step method [
41] (note: the details of terms presented in Equation (2) can be seen in [
38]). Furthermore, when carrying out the unsteady flow simulation, the HEC-RAS applies the continuity and momentum equations for determining the stage and flow at all locations in the model (see [
38] for more details).
where
Z1, Z2—elevation of the main channel inverts
Y1, Y2—water depth at cross sections
V1, V2—average velocities
a1, a2—Saint Venant coefficients describing the variability of velocity profile in the particular cross section
g—gravitational acceleration
he—energy head loss
2.7.1. Schematic of the River System
To connect the river system, the schematic of the river system was firstly built using the geometric data editor available in HEC-RAS. Thereafter, the river system parts such as rivers, junctions, and additional hydraulic structures located along the rivers, can be properly depicted. All the values of the cross section, i.e., station, elevation, left and right overbanks, reach length, Manning’s roughness coefficients, left bank, right bank, and energy loss coefficients (friction, expansion, and contraction losses), must be entered, as the cross section describes the terrain profile of the river where the flooding on left/right banks can be clearly indicated.
2.7.2. Boundary Condition
Boundary conditions are required to establish the starting water surface for HEC-RAS to begin its calculations. The up- and downstream boundary conditions were entered for each reach, whereas the internal boundary conditions were defined for connections to junctions. The flow from each sub-basin determined by HEC-HMS hydrological model, together with the released flow from Ubol Ratana Dam stored in HEC Data Storage System (DSS), were imported into the HEC-RAS model through the unsteady flow data editor option. The diverted flow to irrigation canal system, which was assigned negative values, was also modelled to evaluate canal hydraulics for both steady and unsteady flow conditions. Regarding the downstream boundary condition, the type of boundary condition called “Normal Depth”, which is based on the assumption that the river flows under normal flow (uniform flow) conditions at the downstream boundary of the HEC-RAS set-up model, was selected. In detail, the normal depth or the stage for each computed flow was calculated based on Manning’s equation, by using the slope of the channel bottom, 0.00011 m/m.
2.8. Model Calibration and Validation
The fundamental operation, the model calibration, was undertaken by adjusting/tuning identified sensitive parameters used in the HEC-HMS model at gauging station E.22B (discharge) and inflow to Ubol Ratana reservoir at a daily time-step during the period 2005 to 2011, and the 1D HEC-RAS model for daily water level at gauging station E.22B at a time-step during the flood period (August to December 2010) until the model simulation results closely match the observed values. In addition, the model evaluation procedure was also conducted through model validation process in order to prove that both set-up models are accurately capable of representing physical processes and providing predictive capabilities under different—though similar—conditions, based on a set of calibrated parameters and another set of hydrological data. For validation, the simulated outputs calculated by both models were also compared with the observed data at E.22B, i.e., daily discharge during the years 2012 to 2017 was used to validate the HEC-HMS, and daily water levels during the severe flood period (August to December 2011). The Coefficient of Determination (R
2) and Nash–Sutcliffe Efficiency (NSE) [
42], which are reliable criteria, were used to assess the goodness of both model performances during calibration and validation periods (see Equations (3) and (4) for the detailed formulas).
where
Oi—observed value at time-step i
Oavg—average observed value of the simulation period
Pi—simulated value at time-step i
Pavg—average simulated value of the simulation period
To precisely verify the results simulated by the 2D HEC-RAS model, the goodness of fit between the generated flood map from the HEC-RAS and the flood map extracted from the satellite images from Geo-Informatics and Space Technology Development Agency (Public Organization—GISTDA) was considered and assessed by the measure of Relative Error (RE) (Equation (5)), which is a measure that describes the percentage-difference between observed and simulated values over a specified time period and is useful in diagnostics of over-prediction or under-prediction (smaller values are the indication of better model performance). The F-statistics (F) (Equation (6)), which are the ratios of the area of the overlapping portion of the two flood extents to the area of both flood extents projected on the map, were also used to denote the overall goodness of fit of the HEC-RAS model simulations (a high F-statistic indicates very good model performance).
where
—the inundation area extracted from satellite images
—the HEC-RAS generated flood inundation area
—the intersection of and
2.9. Assessment of Flood Impacts and Damage
The amount of damage resulting from floods relies on flood characteristics, i.e., depth and duration. In this study, the flood damage assessment was performed based on direct damage estimation, which occurs as a consequence of the physical contact of floodwater with lives, properties, and any other objects. The damage functions derived by [
43] (Equations (7) and (8)) were used for direct damage determination, in which four major types of land use were included in the calculation, i.e., residential, commercial, industrial, and agricultural. The list of coefficients for each land use type used in Equation (7) can be presented in
Table 2.
where
DPE—direct flood damage per land use type (Thai Baht)
H—maximum flood depth (cm)
L—flood duration (day)
a
0, a
1, a
2—flood damage coefficients (see
Table 2)
The direct flood damage per land use type calculated by Equation (7) was then used to determine the direct flood damage for all land use types in Thai Baht by Equation (8).
where
DAM—direct flood damage (Thai Baht)
DPE (j, H, L)—direct flood damage per land use type j at H, L (Thai Baht /land use type)
APE (j)—average area per land use type j per unit (m
2) (see
Table 3)
PC (i, j)—percentage of land use type j in cell i (-)
AREA (i)—area of cell i (m2)
i—number of cell (-)
j—land use type 1, 2, 3, 4 (residential, commercial, industrial, agricultural) (-)
H—maximum flood depth (m)
L—flood duration (day)
It can be seen that the direct flood damage to infrastructure was excluded from the direct flood damage calculation. Therefore, as suggested by [
46], the flood damage to infrastructure can be estimated at as high as 65% of the total direct flood damage, which enables the so-called “Total Direct Flood Damage (TDM)” to be calculated in Thai Baht (Equation (9)).
To achieve a better understanding from the above-detailed processes, the summarized key steps involved in the estimation of total direct flood damage of different return periods in the lower Nam Phong River Basin for land use and climate change scenarios are presented in
Figure 4.
4. Conclusions
In this study, the potential climate and land use change impacts on floods in the selected case study, the lower Nam Phong River Basin, was undertaken using HEC-HMS hydrological and HEC-RAS hydraulic models under different return periods and future emission scenarios. The future climate change was projected for the years 2020–2039 (early century) in comparison to the baseline period of 2000–2017, under a set of Representative Concentration Pathway (RCP) greenhouse gas scenarios (RCPs 4.5 and 8.5) from CMIP5 model simulations, i.e., CNRM-CM5, IPSL-CM5A-MR, and MPI-ESM-LR. The high resolution downscaled (50-km grid spacing) and bias corrected daily rainfall was then used as an input for the calibrated HEC-HMS model (periods of 2005–2011 and 2012–2017 for calibration and validation, respectively) to generate a future daily discharge time series, in which the flood inundation maps were obtained by the calibrated HEC-RAS model (wet periods of 2010 and 2011 for calibration and validation, respectively).
The simulation findings revealed that, during the period 2000–2017, the potential flooded area in the lower Nam Phong River Basin with 25-, 50-, and 100-year return periods are 140.95 km2, 150.45 km2, and 165.33 km2, respectively, meanwhile the 2011 flood extent is about 128.08 km2. In view of future scenarios, the extent of flood inundation under RCP 4.5 is smaller than the baseline case for 25-, 50-, and 100-year return periods by 4.97 km2, 1.01 km2, and 8.59 km2, respectively, whereas the flood extent under RCP 8.5 is larger than the baseline condition for 25- and 50-year return periods by 5.30 km2 and 3.86 km2, respectively, and almost no difference is found for the 100-year return period. The severity of flood events is projected to be increased and is likely to be serious in the RCP 8.5 scenario rather than RCP 4.5 scenario. There is little difference, in fact, in flood extent between the baseline and future cases, nevertheless, it is obvious that the future flood duration tends to increase. The inundation extent with zero to two months of flood duration is likely to decrease, whereas the extent with four to six months of flood duration is expected to be increased, especially for high return periods.
By considering the maximum flood depth and flood duration into the calculation of total direct flood damage, the direct flood damage clearly increases, with higher return periods for both the baseline and future conditions. With respect to the baseline, the total direct damage is estimated at 10.52, 11.50, and 12.69 million US$ at the 25-, 50-, and 100-year return periods, respectively. In terms of future conditions, the total direct damage under RCP 4.5 is expected to be 14.84, 16.91, and 18.02 million US$ for the 25-, 50-, and 100-year return periods, respectively, whereas the total direct damage under RCP 8.5 is found to be higher by 1.40, 0.49, and 0.65 million US$, respectively. In addition, most of the total direct flood damage is in agriculture, followed by infrastructure and residential area, for both the baseline and future scenarios. However, the future agricultural damage is detected to be decreased from the baseline by approximately 18%, while the future damage for residential (expected to be increased from the baseline of up to 17%), commercial, and industrial areas tend to be increased from the baseline. Above all, it can be said that the future flood damage tends to increase because of changes in climate, together with the effect of increased exposure due to land use conversion.
Finally, the main findings from this study should prove very useful for defining and directing effective adaptation strategies to limit potential flood risks in the lower Nam Phong River Basin to a low level, both in probability and damage. The findings also could be used as a guideline for other areas throughout Thailand.