Next Article in Journal
Successes and Issues in the Growth of Moad and MoSe2 on Ag(111) by the E-ALD Method
Next Article in Special Issue
Study of the Deposition Formation Mechanism in the Heat Exchanger System of RHF
Previous Article in Journal
Hydrogen Solubility in Pd3Ag Phases from First-Principles Calculation
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Metals
Volume 9
Issue 2
10.3390/met9020120
metals-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Study of Sputtered ITO Films on Flexible Invar Metal Foils for Curved Perovskite Solar Cells

by
Hae-Jun Seok
and
Han-Ki Kim
*
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon, Gyeonggi-do 16419, Korea
*
Author to whom correspondence should be addressed.
Metals 2019, 9(2), 120; https://doi.org/10.3390/met9020120
Submission received: 3 December 2018 / Revised: 20 January 2019 / Accepted: 22 January 2019 / Published: 24 January 2019
(This article belongs to the Special Issue Metal Oxides)
Browse Figures
Review Reports Versions Notes

Abstract

:
We have studied characteristics of tin-doped indium oxide (ITO) films sputtered on flexible invar metal foil covered with an insulating SiO2 layer at room temperature to use as transparent electrodes coated substrates for curved perovskite solar cells. Sheet resistance, optical transmittance, surface morphology, and microstructure of the ITO films on SiO2/invar substrate are investigated as a function of the thickness from 50 to 200 nm. The optimized ITO film exhibits a low sheet resistance of 50.21 Ohm/square and high optical transmittance of up to 94.31% even though it is prepared at room temperature. In particular, high reflectance of invar metal substrate could enhance the power conversion efficiency of curved perovskite solar cell fabricated on the ITO/SiO2/invar substrate. In addition, critical bending radius of the 150 nm-thick ITO film is determined by lab-designed outer and inner bending tests to show feasibility as flexible electrode. Furthermore, dynamic fatigue test is carried out to show flexibility of the ITO film on invar metal substrate. This suggests that the ITO/SiO2/invar substrate can be applied as flexible electrodes and substrates for curved perovskite solar cells.

1. Introduction

Methylammonium lead tri-iodide (MAPbI3) perovskite solar cells (PSCs) have emerged as next generation photovoltaics following Si-based photovoltaics and organic photovoltaics due to their high power conversion efficiencies larger than 20% and solution-based simple fabrication process [1,2,3,4,5]. In particular, planar heterojunction type flexible perovskite solar cells have been extensively investigated because planar architecture is easily fabricated on flexible substrate at low temperature. However, most flexible PSCs fabricated on plastic substrate exhibited limit in reliability and stability due to high water vapor transmission rate (WVTR) values of conventional plastic substrates [6,7,8,9,10,11]. To solve the problem of typical plastic substrates, flexible metal foils with smooth surface have emerged as promising flexible substrate for flexible photovoltaics and flexible organic light emitting diodes (OLEDs) [12,13,14,15,16]. Especially, metal foil substrates have many advantages over polymer substrates, such as enhanced chemical stability and lower thermal expansion coefficients. Furthermore, a high temperature process is possible due to the higher thermal stability of metal foil compared to that of polymers, and a passivation layer is not required to prevent water vapor and oxygen migrating through the substrate [17,18,19,20]. On the other hand, impurities from the metal substrate and surface roughness are significant issues impeding their electronic applications. In particular, device performance may deteriorate due to out-diffusion of detrimental elements from the metal foil, such as Fe atoms, and electrical short circuits (i.e., direct contact of the anode and cathode electrode in solar cell devices) due to severe surface roughness [21,22,23]. Lee et al. suggested that invar metal foil is a promising flexible substrate material for flexible OLEDs [12]. Im et al. also reported that flexible PSCs fabricated on metal foil had a power conversion efficiency of 15% [24]. Typically, most of PSCs have been fabricated on physical vapor deposited Sn-doped In2O3 (ITO) electrode [25,26,27]. DC sputtered amorphous ITO films with fairly high sheet resistances (30–100 Ohm/square) and average optical transmittances of 80–85% have been widely employed as flexible electrodes for flexible optoelectronic devices. Although the potential of invar metal foil as flexible substrate for flexible optoelectronic devices has been well-known, detailed investigation of Sn-doped In2O3 (ITO) films on invar metal foil is still necessary. Recently, we reported high quality flexible ITO electrodes with a low sheet resistance of 15.75 Ohm/square, high optical transmittance of 85.88%, and outstanding flexibility grown by ion plating for flexible PSCs [28]. Because most research of PSCs has mainly been focused on active materials and interface buffer layers, investigation of flexible ITO films for curved or flexible PSCs is still lacking.
In this study, we investigated the electrical, optical, morphological and mechanical properties of DC sputtered ITO films on invar foil substrate as a function of ITO film thickness to show feasibility of invar metal substrate for curved perovskite solar cells. In particular, outer and inner bending tests were carried out to determine critical bending radius of ITO film on the invar metal substrate. In addition, resistance change of the ITO films during repeated bending cycles at a fixed bending radius of 15 mm was measured to show stable mechanical flexibility. The possible growth mechanism of ITO films on the SiO2 coated invar metal substrate was suggested to correlate film thickness and characteristics of ITO films. In addition, we report a preliminary study of a perovskite solar cell fabricated on invar substrate.

2. Materials and Methods

The 120 μm thick invar metal foil (36% Ni–64% Fe) was employed as flexible substrate to deposit flexible ITO anode for curved perovskite solar cells. Before sputtering of ITO films, the 2 μm thick SiO2 insulating layer was deposited on invar substrate using plasma enhanced chemical vapor deposition. Then, transparent ITO film with a thickness in the range 50–200 nm was sputtered on the SiO2 coated invar substrate using a four-inch ITO target (Dasom RMS) at room temperature. During ITO sputtering process, DC power of 100 W, Ar flow rate of 20 sccm, and a working pressure of 3 mTorr was kept constant. Figure 1a shows the fabrication process of flexible ITO films on invar substrate. The ITO coated invar foil could be used as flexible substrate in curved perovskite solar cells as illustrated in Figure 1b. Due to opacity of invar substrate, the light was absorbed through the transparent top cathode unlike typical glass-based perovskite solar cells. The thickness of ITO films was measured using a profilometer (NanoMap LS, aep Technology, Newyork, NY, USA). Through Hall measurements (HMS-4000AM, Ecopia, Anyang-si, Korea) and a UV–visible spectrometer (UV 540, Unicam, Hachioji, Japan) analysis, the electrical and optical properties of the flexible ITO films were examined as a function of thickness. The morphology and microstructure of ITO film on SiO2 coated invar substrate according to the increasing thickness was examined by field emission scanning electron microscope (FESEM: JSM-7600F, JEOL, Akishima, Japan) and X-ray diffraction (XRD, D8 ADVANCE, Bruker Corporation, Billerica, MA, USA). The mechanical flexibility of the ITO films on SiO2 coated invar substrate was investigated by using a lab-designed outer/inner bending test machine (JUNIL TECH Co., DaeGu-Si, Korea). The resistance changes of the ITO films during outer and inner bending of substrate were measured with decreasing bending radius in order to determine critical bending radius. By pressing the clamped samples, we can control the bending radius. In outer and inner bending tests, both clamps moved simultaneously to specific position to make specific bending radius. Then, dynamic outer/inner fatigue tests were performed at a fixed bending radius of 15 mm for 10,000 cycles.

3. Results and Discussion

Figure 2a,b shows the Hall measurement results of ITO films sputtered on SiO2 coated invar substrate and glass substrate in same chamber with increasing film thicness. With increasing ITO film thickness, the sheet resistance gradually decreased. Table 1 summarized sheet resistance of ITO films on the SiO2 coated invar and glass substrate, respectively. Regardless of substrates, the DC sputtered ITO films showed a similar sheet resistance at a same film thickness. Because the insulating SiO2 layer completely covered the invar substrate, the ITO film on SiO2/invar substrate showed a similar sheet resistance to the ITO films on glass substrates. At a thickness of 200 nm, the ITO films on SiO2/invar and glass substrate showed an identical sheet resistance of 44.57 and 44.52 Ohm/square and resistivity of 8.91 × 10−4 and 8.90 × 10−4 Ohm × cm, respectively.
Figure 2c shows optical transmittance of ITO films on the glass substrate. Due to opacity of invar substrate, the optical transmittance of the ITO films was measured from the ITO film sputtered on glass substrate at same sputtering conditions with invar substrates. All ITO films show a high optical transmittance in the visible region regardless film thickness. With increasing ITO film thickness, oscillations in the optical transmittance was observed due to light interference phenomena [29,30]. Table 2 showed the average transmittance (400–800 nm) of ITO films on glass substrate as a function of thickness. At the 150nm-thick ITO film, the average transmittance had the highest value of 88.73%. To determine optimum ITO thickness, we compared figure of merit (FoM = T10/Rsh) values, which were calculated from the average optical transmittance (T) and the sheet resistance (Rsh), as shown in Figure 2d [31]. Because the active layer of the PSCs absorbs visible light (400–800 nm), the FoM values are calculated using the average optical transmittance (400–800 nm). In addition, the voltage loss of the PSCs is influenced by the sheet resistance of the transparent electrode. Therefore, the exciton generation and voltage loss of the PSC are closely related to the FoM value, which is the quality of the transparent electrode. For those reasons, the optimum ITO thickness on the invar substrate was determined by the FoM value. Based on FoM calculation, we found that the 150 nm-thick ITO film had the highest FoM value of 6.02 Ohm−1. In invar-based perovskite solar cells, optical reflectance on the surface of invar substrate is very important because photon penetrating perovskite active layer could be reflected from the surface of invar substrate as illustrated in Figure 1b.
Figure 3a shows optical reflectance of ITO/SiO2/invar samples with different ITO thickness. Due to high reflectance of invar substrate, all samples showed high reflectance regardless of ITO thickness. Optical reflectance of the ITO/SiO2/invar samples are similar to SiO2/invar substrate. Figure 3b exhibited XRD plots of ITO films on SiO2/invar substrate with increasing thickness. The diffraction peaks appear at 2θ = 30.28°, 35.18°, 37.06°, 50.57°, and 60.15°, corresponding to the (222), (400), (411), (440), and (622) orientations. The several diffraction peaks demonstrate that the DC sputtered ITO films have a typical bixbyite structure even though they were prepared at room temperature. The intensity of XRD peaks increased due to well-developed polycrystalline structure and increase in sub-grain sizes. In addition, ITO film showed (222) preferred orientation with increasing film thickness. Kim et al. also reported that DC sputtered ITO films had a (222) preferred orientation with increasing film thickness [32]. Although we employed invar metal substrate, the ITO films ware directly sputtered on SiO2 insulating layer, the microstructure of ITO film on SiO2/invar substrate is similar to the ITO films on glass or fused silica (SiO2) substrate.
Figure 4 shows surface FESEM images of DC sputtered ITO films on SiO2/invar substrate with increasing film thickness. At a thickness of 50 nm in Figure 4a, the ITO film showed garlic-flower like surface morphology due to amorphous sub-grain as expected from XRD plot. However, surface FESEM image of the ITO film with a thickness of 100 nm showed sub-grains consisting of micro-crystals as shown in Figure 4b. Further increase in thickness led to (222) preferred oriented surface morphology of ITO films as expected from XRD plots. As shown in Figure 4c, the 150-nm thick ITO films consisted of (222) oriented grains with a triangular-shape. The triangular-shaped ITO grains indicate that DC sputtered ITO films on SiO2/invar substrate have a (222) preferred orientation. However, the 200-nm thick ITO films exhibit triangular-shaped (222), square-shaped (400), and rectangular-shaped (440) grains as shown in Figure 4d [27]. As expected from the XRD plots, these grain shapes indicate that the 200-nm thick ITO film consists of primarily (222), (400), and (440) grains. Due to the difference in sub-grain height, we can easily distinguish the sub-grain direction of DC-grown ITO films on SiO2/invar substrate. As we reported in previous work [27], the surface of sputtered ITO films experienced severe ion bombardments from energetic particles in high density plasma. This bombardment resulted in re-sputtering of the specific plane of the ITO films. Due to different surface energy of special crystalline ITO planes, the re-sputtering phenomenon resulted in specific surface morphology of the ITO film depending on its preferred orientation.
To determine the critical outer and inner bending radii of the ITO film on SiO2/invar substrate, the resistance change (ΔR) of the ITO film was measured in-situ by reducing the bending radius, as shown in Figure 5a. Here, the critical bending radius (rc) is defined as the bending radius where the resistance abruptly increases due to the formation and propagation of cracks. The outer/inner bending test results showed that the 150 nm-thick ITO film on SiO2/invar substrate had a constant resistance until the bending radii became 11 mm (outer bending) or 11 mm (inner bending), as shown in Figure 5a. Beyond this critical bending radius, the resistance of the film rapidly increased due to crack formation and physical separation of the ITO film. Due to thick 2 μm of SiO2 on invar substrate, cracking in the ITO (150 nm)/SiO2 multilayer led to increase in the resistance. Figure 5b shows the dynamic bending test results of the ITO (150 nm)/SiO2/invar substrate with an increasing number of bending cycles at a fixed bending radius of 15 mm, which is larger than critical bending radius. The picture in upper panels in Figure 5b shows the dynamic outer and inner bending fatigue test steps with increasing bending cycles, up to 10,000 cycles.
Figure 5b shows both dynamic outer and inner bending fatigue tests of the ITO (150 nm)/SiO2/invar substrate; no change in the resistance (ΔR) is observed, even after 10,000 bending cycles, demonstrating the outstanding flexibility and mechanical reliability of the ITO (150 nm)/SiO2/invar substrate. Even after 10,000 outer and inner bending cycles, the surface of the ITO film showed an identical morphology to the as-deposited ITO film. The crystalline and featureless surface morphology of the sample is typical of a crystalline ITO film prepared at room temperature. Considering the application of curvature of perovskite solar cells, the outstanding flexibility and small critical bending radius of ITO film on SiO2/invar substrate is acceptable in fabrication of curved perovskite solar cells.
Based on FoM value and bending test results, curved PSC was fabricated on a 150 nm-thick ITO film. Figure 6a depicts current density-voltage (J-V) curve of the PSC on the ITO (150 nm)/SiO2/invar substrate. Figure 6b shows schematic representation of the PSC fabrication processes on the ITO (150 nm)/SiO2/invar substrate. The ITO (150 nm)/SiO2/invar substrate underwent UV/ozone treatment for 10 min before the deposition of a NiO layer. The desired amount of ethanolic precursor solution containing nickel diacetate tetra-hydrate (Ni(CH3COO)2·4H2O) and HCI was refluxed at 60 ℃ for 2 h. Then, NiO layer with an average thickness of 12 nm was fabricated by spin-coating at 3000 rpm for 40 s in air and the film was annealed at 100 ℃ for 30 min. Subsequently, the MAPbI3 was coated onto the NiO layer by spin-coating at 4000 rpm for 45 s in air. The electron transport layer PCBM was grown on the MAPbI3 layer by spin coating at 1000 rpm for 60 s and the film 100 ℃ for 10 min. Finally, 200 nm IZTO cathodes were formed successively, with the damage-free linear facing target sputtering by using a dumbbell-shaped shadow mask [33]. Table 3 summarizes the key J-V parameters of the curved PSC. The J-V curve of the performing device yields a VOC of 1.11 V, a JSC of 18.12 mA/cm2, a fill factor of 47%, and a PCE of 9.70%. Although the PCE of the curved PSC fabricated on ITO/SiO2/invar substrate is lower than glass based PSC at this moment, we strongly believe that further optimization of fabrication process could increase PCE of the curved PSC on invar substrate. However, successful operation of curved PSC on invar substrate demonstrates the feasibility of flexible invar substrate for next-generation curved PSCs.

4. Conclusions

The electrical, optical, morphological, and structural properties of DC sputtered ITO films on SiO2/invar substrates were investigated as a function of ITO thickness. We found that the resistivity and optical transmittance of DC sputtered ITO film on SiO2/invar is dependent on film thickness. With increasing thickness, the ITO film showed a well-developed crystalline structure with (222) preferred orientation. Based on outer/inner bending test and dynamic fatigue tests, we confirmed the outstanding mechanical flexibility of the ITO/SiO2/invar substrate. Based on electrical, optical, and mechanical properties of ITO film on SiO2/invar substrate, we suggested that the DC sputtered ITO film on SiO2/invar substrate could substitute ITO film on plastic substrate for curved perovskite solar cells. In addition, a preliminary study of the ITO coated-invar metal foils as a flexible substrate for curved PSCs indicates that invar metal foils are promising flexible substrates to substitute typical flexible polymer substrates for high performance curved PSCs.

Author Contributions

Design of experiment, H.-K.K.; Sputtering and Analysis, H.-J.S.

Funding

This work was supported by the Korea Institute of Energy Technology Evaluation and Planning (KETEP) and the Ministry of Trade, Industry & Energy (MOTIE) of the Republic of Korea (No. 20163010012200). This study also received partial support from Korea Electric Power Corporation (KEPCO, CX72170049).

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Jamal, M.S.; Bashar, M.S.; Mahmud Hasan, A.K.; Almutairi, Z.A.; Alharbi, H.F.; Alharthi, N.H.; Karim, M.R.; Misran, H.; Amin, N.; Sopian, K.B.; et al. Fabrication techniques and morphological analysis of perovskite absorber layer for high-efficiency perovskite solar cell: A review. Renew. Sustain. Energy Rev. 2018, 98, 469–488. [Google Scholar] [CrossRef]
  2. Stranks, S.D.; Snaith, H.J. Metal-halide perovskites for photovoltaic and light-emitting devices. Nat. Nanotechnol. 2015, 10, 391–402. [Google Scholar] [CrossRef]
  3. Li, J.; Jiu, T.; Duan, C.; Wang, Y.; Zhang, H.; Jian, H.; Zhao, Y.; Wang, N.; Huang, C.; Li, Y. Improved electron transport in MAPbI3 perovskite solar cells based on dual doping graphdiyne. Nano Energy 2018, 46, 331–337. [Google Scholar] [CrossRef]
  4. Saliba, M.; Matsui, T.; Seo, J.Y.; Domanski, K.; Correa-Baena, J.P.; Nazeeruddin, M.K.; Zakeeruddin, S.M.; Tress, W.; Abate, A.; Hagfeldt, A.; Grätzel, M. Cesium-containing triple cation perovskite solar cells: Improved stability, reproducibility and high efficiency. Energy Environ. Sci. 2016, 9, 1989–1997. [Google Scholar] [CrossRef] [PubMed]
  5. You, S.; Wang, H.; Bi, S.; Zhou, J.; Qin, L.; Qiu, X.; Zhao, Z.; Xu, Y.; Zhang, Y.; Shi, X.; Zhou, H.; Zhiyong, T. A biopolymer heparin sodium interlayer anchoring TiO2 and MAPbI3 enhances trap passivation and device stability in perovskite solar cells. Adv. Mater. 2018, 30, 1706924. [Google Scholar] [CrossRef]
  6. Bu, T.; Li, J.; Zheng, F.; Chen, W.; Wen, X.; Ku, Z.; Peng, Y.; Zhong, J.; Cheng, Y.B.; Huang, F. Universal passivation strategy to slot-die printed SnO2 for hysteresis-free efficient flexible perovskite solar module. Nat. Commun. 2018, 9, 4609. [Google Scholar] [CrossRef] [PubMed]
  7. Asghar, M.I.; Zhang, J.; Wang, H.; Lund, P.D. Device stability of perovskite solar cells—A review. Renew. Sustain. Energy Rev. 2017, 77, 131–146. [Google Scholar] [CrossRef]
  8. Giacomo, F.D.; Fakharuddin, A.; Jose, R.; Brown, T.M. Progress, challenges and perspectives in flexible perovskite solar cells. Energy Environ. Sci. 2016, 9, 3007–3035. [Google Scholar] [CrossRef] [Green Version]
  9. Shin, S.S.; Yang, W.S.; Noh, J.H.; Suk, J.H.; Jeon, N.J.; Park, J.H.; Kim, J.S.; Seong, W.M.; Seok, S.I. High-performance flexible perovskite solar cells exploiting Zn2SnO4 prepared in solution below 100 °C. Nat. Commun. 2015, 6, 7410. [Google Scholar] [CrossRef] [PubMed]
  10. Zardetto, V.; Brown, T.M.; Reale, A.; Carlo, A.D. Substrates for flexible electronics: A practical investigation on the electrical, film flexibility, optical temperature, and solvent resistance properties. J. Polym. Sci. Part B Polym. Phys. 2011, 49, 638–648. [Google Scholar] [CrossRef]
  11. Burrows, P.E.; Graff, G.L.; Gross, M.E.; Martin, P.M.; Shi, M.K.; Hall, M.; Mast, E.; Bonham, C.; Bennett, W.; Sullivan, M.B. Ultra barrier flexible substrates for flat panel displays. Displays 2001, 22, 65–69. [Google Scholar] [CrossRef]
  12. Kim, K.; Kim, S.; Jung, G.H.; Lee, I.; Kim, S.; Ham, J.; Dong, W.J.; Hong, K.; Lee, J.L. Extremely flat metal films implemented by surface roughness transfer for flexible electronics. RSC Adv. 2018, 8, 10883–10888. [Google Scholar] [CrossRef] [Green Version]
  13. Luo, Z.; Lu, Y.; Singer, D.W.; Berck, M.E.; Somers, L.A.; Goldsmith, B.R.; Charlie Johnson, A.T. Effect of substrate roughness and feedstock concentration on growth of wafer-scale graphene at atmospheric pressure. Chem. Mater. 2011, 23, 1441–1447. [Google Scholar] [CrossRef]
  14. Calabrese, G.; Pettersen, S.V.; Pfüller, C.; Ramsteiner, M.; Grepstad, J.K.; Brandt, O.; Geelhaar, L.; Fernandez-Garrido, S. Effect of surface roughness, chemical composition, and native oxide crystallinity of the orientation of self-assembled GaN nanowires on Ti foils. Nanotechnology 2017, 28, 425602. [Google Scholar] [CrossRef]
  15. Hong, K.; Yu, H.K.; Lee, I.; Kim, S.; Kim, Y.; Kim, K.; Lee, J.L. Flexible top-emitting organic light emitting diodes with a functional dielectric reflector on a metal foil substrate. RSC Adv. 2018, 8, 26156–26160. [Google Scholar] [CrossRef]
  16. Cheon, J.H.; Choi, J.H.; Hur, J.H.; Jang, J.; Shin, H.S.; Jeong, J.K.; Mo, Y.G.; Chung, H.K. Active-matrix OLED on bendable metal foil. IEEE Trans. Electron Devices 2006, 53, 1273–1276. [Google Scholar] [CrossRef]
  17. Kim, M.; Kim, K.B.; Jeon, C.W.; Lee, D.; Lee, S.N.; Lee, J.M.; Lee, H.C. CIGS solar cell devices on steel substrates coated with Na containing AIPO4. J. Phys. Chem. Solids 2015, 86, 223–228. [Google Scholar] [CrossRef]
  18. Kim, K.B.; Kim, M.; Lee, H.C.; Park, S.W.; Jeon, C.W. Copper indium gallium selenide (CIGS) solar cell devices on steel substrates coated with thick SiO2-based insulating material. Mater. Res. Bull. 2017, 85, 168–175. [Google Scholar] [CrossRef]
  19. Kim, K.B.; Kim, M.; Baek, J.; Park, Y.J.; Lee, J.R.; Kim, J.S.; Jeon, C. Influence of Cr thin films on the properties of flexible CIGS solar cells on steel substrates. Electron. Mater. Lett. 2014, 10, 247–251. [Google Scholar] [CrossRef]
  20. Si, P.Z.; Choi, C.J. High hardness nanocrystalline invar alloys prepared from Fe-Ni nanoparticles. Metals 2018, 8, 28. [Google Scholar] [CrossRef]
  21. Herz, K.; Eicke, A.; Kessler, F.; Wächter, R.; Powalla, M. Diffusion barrier for CIGS solar cells on metallic substrates. Thin Solid Films 2003, 431–432, 392–397. [Google Scholar] [CrossRef]
  22. Batchelor, W.K.; Repins, I.L.; Schaefer, J.; Beck, M.E. Impact of substrate roughness on CuInxGa1−xSe2 device properties. Sol. Energy Mater. Sol. Cells 2004, 83, 67–80. [Google Scholar] [CrossRef]
  23. Platzer-Björkman, C.; Jani, S.; Westlinder, J.; Linnarsson, M.K.; Scragg, J.; Edoff, M. Diffusion of Fe and Na in co-evaporated Cu(In,Ga)Se2 devices on steel substrates. Thin Solid Films 2013, 535, 188–192. [Google Scholar] [CrossRef]
  24. Heo, J.H.; Shin, D.H.; Lee, M.L.; Kang, M.G.; Im, S.H. Efficient organic-inorganic hybrid flexible perovskite solar cells prepared by lamination of polytriarylamine/CH3NH3PbI3/anodized Ti metal substrate and graphene/PDMS transparent electrode substrate. ACS Appl. Mater. Interfaces 2018, 10, 31413–31421. [Google Scholar] [CrossRef] [PubMed]
  25. Suyama, T.; Bae, H.; Setaka, K.; Ogawa, H.; Fukuoka, Y.; Suzuki, H.; Toyoda, H. Quantitative evaluation of high-energy O-ion particle flux in a DC magnetron sputter plasma with an indium-tin-oxide target. J. Phys. D Appl. Phys. 2017, 50, 445201. [Google Scholar] [CrossRef]
  26. Lee, K.Y.; Chen, L.C.; Wu, Y.J. Effect of oblique-angle sputtered ITO electrode in MAPbI3 perovskite solar cell structures. Nanoscale Res. Lett. 2017, 12, 556. [Google Scholar] [CrossRef]
  27. Kim, J.H.; Seong, T.Y.; Ahn, K.J.; Chung, K.B.; Seok, H.J.; Seo, H.J.; Kim, H.K. The effects of film thickness on the electrical, optical, and structural properties of cylindrical, rotating, magnetron-sputtering ITO films. Appl. Surf. Sci. 2018, 440, 1211–1218. [Google Scholar] [CrossRef]
  28. Kim, J.H.; Seok, H.J.; Seo, H.J.; Seong, T.Y.; Heo, J.H.; Lim, S.H.; Ahn, K.J.; Kim, H.K. Flexible ITO films with atomically flat surfaces for high performance flexible perovskite solar cells. Nanoscale 2018, 10, 20587–20598. [Google Scholar] [CrossRef]
  29. Akman, E.; Cerkezoglu, E. Compositional and micro-scratch analyses of laser induced colored surface of titanium. Opt. Lasers Eng. 2016, 84, 37–43. [Google Scholar] [CrossRef]
  30. Pérez del Pino, A.; Fernández-Pradas, J.M.; Serra, P.; Morenza, J.L. Coloring of titanium through laser oxidation: Comparative study with anodizing. Surf. Coat. Technol. 2004, 187, 106–112. [Google Scholar] [CrossRef]
  31. Haacke, G. New figure of merit for transparent conductors. J. Appl. Phys. 1976, 47, 4086–4089. [Google Scholar] [CrossRef]
  32. Kim, H.; Horwitz, J.S.; Kushto, G.; Piqué, A.; Kafafi, Z.H.; Gilmore, C.M.; Chrisey, D.B. Effect of film thickness on the properties of indium tin oxide thin films. J. Appl. Phys. 2000, 88, 6021–6025. [Google Scholar] [CrossRef]
  33. Lee, J.H.; Shin, H.S.; Na, S.I.; Kim, H.K. Transparent and flexible PEDOT:PSS electrodes passivated by thin IZTO film using plasma-damage free linear facing target sputtering for flexible organic solar cells. Sol. Energy Mater. Sol. Cells 2013, 109, 192–198. [Google Scholar] [CrossRef]
Metals 09 00120 g001 550
Figure 1. (a) Schematic fabrication process of flexible ITO films on SiO2 coated invar metal substrate using typical DC magnetron sputtering at room temperature. The images show ITO sputtering process and curved invar substrate with ITO electrodes. (b) Device structure of curved perovskite solar cells with transparent InSnO anode and InZnSnO top cathode.
Figure 1. (a) Schematic fabrication process of flexible ITO films on SiO2 coated invar metal substrate using typical DC magnetron sputtering at room temperature. The images show ITO sputtering process and curved invar substrate with ITO electrodes. (b) Device structure of curved perovskite solar cells with transparent InSnO anode and InZnSnO top cathode.
Metals 09 00120 g001
Metals 09 00120 g002 550
Figure 2. Hall measurement results of ITO films on (a) SiO2 coated invar and (b) glass substrates prepared at room temperature with increasing thickness (50, 100, 150, 200 nm). (c) Optical transmittance of ITO films on glass substrates. Inset: pictures of ITO films deposited on invar substrates (upper figure) and on glass substrates (lower figure). (d) Figure of merit (FoM = T10/Rsh) of ITO film on SiO2/invar substrates as a function of thickness.
Figure 2. Hall measurement results of ITO films on (a) SiO2 coated invar and (b) glass substrates prepared at room temperature with increasing thickness (50, 100, 150, 200 nm). (c) Optical transmittance of ITO films on glass substrates. Inset: pictures of ITO films deposited on invar substrates (upper figure) and on glass substrates (lower figure). (d) Figure of merit (FoM = T10/Rsh) of ITO film on SiO2/invar substrates as a function of thickness.
Metals 09 00120 g002
Metals 09 00120 g003 550
Figure 3. (a) Reflectance ITO films sputtered on SiO2 coated invar substrate with increasing film thickness. (b) XRD plots of the ITO films sputtered on SiO2 coated invar substrate at room temperature as a function of film thickness.
Figure 3. (a) Reflectance ITO films sputtered on SiO2 coated invar substrate with increasing film thickness. (b) XRD plots of the ITO films sputtered on SiO2 coated invar substrate at room temperature as a function of film thickness.
Metals 09 00120 g003
Metals 09 00120 g004 550
Figure 4. Surface FESEM images of DC sputtered ITO films on SiO2/invar substrates; (a) 50 nm, (b) 100 nm, (c) 150 nm, and (d) 200 nm.
Figure 4. Surface FESEM images of DC sputtered ITO films on SiO2/invar substrates; (a) 50 nm, (b) 100 nm, (c) 150 nm, and (d) 200 nm.
Metals 09 00120 g004
Metals 09 00120 g005 550
Figure 5. (a) Upper panels show pictures of the outer bending test steps with decreasing bending radius. Results of the outer and inner bending test with decreasing bending radius of 150 nm thick ITO films on SiO2/invar substrate. Insets show the schematics of curved sample experiencing tensile and compressive stress. (b) Results of the outer and inner dynamic bending fatigue tests at a fixed bending radius of 15 mm for the 150 nm thick ITO films on SiO2/invar substrate. The right side shows FESEM images of the ITO film before and after dynamic fatigue test after 10,000 cycles.
Figure 5. (a) Upper panels show pictures of the outer bending test steps with decreasing bending radius. Results of the outer and inner bending test with decreasing bending radius of 150 nm thick ITO films on SiO2/invar substrate. Insets show the schematics of curved sample experiencing tensile and compressive stress. (b) Results of the outer and inner dynamic bending fatigue tests at a fixed bending radius of 15 mm for the 150 nm thick ITO films on SiO2/invar substrate. The right side shows FESEM images of the ITO film before and after dynamic fatigue test after 10,000 cycles.
Metals 09 00120 g005
Metals 09 00120 g006 550
Figure 6. (a) Current density-voltage (J-V) curve of PSC fabrication on the ITO (150 nm)/SiO2/invar substrate (under AM 1.5 solar light). (b) Schematic of a PSC fabrication procedure on the ITO (150 nm)/SiO2/invar substrate.
Figure 6. (a) Current density-voltage (J-V) curve of PSC fabrication on the ITO (150 nm)/SiO2/invar substrate (under AM 1.5 solar light). (b) Schematic of a PSC fabrication procedure on the ITO (150 nm)/SiO2/invar substrate.
Metals 09 00120 g006
Table
Table 1. Sheet resistance of ITO films on the SiO2/invar and glass substrates with increasing ITO thickness.
Table 1. Sheet resistance of ITO films on the SiO2/invar and glass substrates with increasing ITO thickness.
SubstrateSheet Resistance (Rs) (Ohm/square)
50 nm100 nm150 nm200 nm
Invar75.5454.7450.2144.57
Glass77.6453.3049.5144.52
Table
Table 2. Average transmittance of ITO films on the glass substrate with increasing ITO thickness.
Table 2. Average transmittance of ITO films on the glass substrate with increasing ITO thickness.
SubstrateAverage Transmittance (400–800 nm) (%)
50 nm100 nm150 nm200 nm
Glass86.2386.1288.7387.01
Table
Table 3. Key parameters of PSC based on ITO (150 nm)/SiO2/invar substrate.
Table 3. Key parameters of PSC based on ITO (150 nm)/SiO2/invar substrate.
ITO Thickness (nm)VOC (V)JSC (mA/cm2)Fill Factor (FF, %)Power Conversion Efficiency (PCE, %)
1501.1118.1247.09.70

Share and Cite

MDPI and ACS Style

Seok, H.-J.; Kim, H.-K. Study of Sputtered ITO Films on Flexible Invar Metal Foils for Curved Perovskite Solar Cells. Metals 2019, 9, 120. https://doi.org/10.3390/met9020120

AMA Style

Seok H-J, Kim H-K. Study of Sputtered ITO Films on Flexible Invar Metal Foils for Curved Perovskite Solar Cells. Metals. 2019; 9(2):120. https://doi.org/10.3390/met9020120

Chicago/Turabian Style

Seok, Hae-Jun, and Han-Ki Kim. 2019. "Study of Sputtered ITO Films on Flexible Invar Metal Foils for Curved Perovskite Solar Cells" Metals 9, no. 2: 120. https://doi.org/10.3390/met9020120

APA Style

Seok, H. -J., & Kim, H. -K. (2019). Study of Sputtered ITO Films on Flexible Invar Metal Foils for Curved Perovskite Solar Cells. Metals, 9(2), 120. https://doi.org/10.3390/met9020120

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop