Next Article in Journal
Measurement of Tire-Pavement Contact Tri-Axial Stress Distribution Based on Sensor Array
Next Article in Special Issue
Adsorption of Reactive Red 120 in Decamethyl-Cyclopentasiloxane Non-Aqueous Dyeing System
Previous Article in Journal
Coupled Modeling of Anisotropic Stress-Induced Diffusion and Trapping of Nitrogen in Austenitic Stainless Steel during Nitriding and Thermal Annealing
Previous Article in Special Issue
Bibliometric Evidence on the Trend and Future Direction of the Research on Textile Coloration with Natural Sources
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Coatings
Volume 13
Issue 2
10.3390/coatings13020414
coatings-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Pullulan Films with PCMs: Recyclable Bio-Based Films with Thermal Management Functionality

by
Nuray Kizildag
Institute of Nanotechnology, Gebze Technical University, Gebze 41400, Kocaeli, Turkey
Coatings 2023, 13(2), 414; https://doi.org/10.3390/coatings13020414
Submission received: 1 January 2023 / Revised: 30 January 2023 / Accepted: 10 February 2023 / Published: 12 February 2023
(This article belongs to the Special Issue Eco-Friendly and Sustainable Textile Processes)
Browse Figures
Versions Notes

Abstract

:
The use of phase-changing materials (PCMs) is a practical and powerful way of buffering thermal fluctuations and maintaining the isothermal nature of the storage process. In this study, melamine formaldehyde microcapsules with paraffin cores were used as PCMs; pullulan films with PCMs were prepared by the film-casting method; and the composite films prepared were analysed with regard to their chemical structure, thermal properties, thermal stability, and recyclability. Uniform films displaying thermal management functionality were prepared. The amount of 75 wt.% PCM were added to the pullulan film structure which enabled the preparation of a composite film that displayed 104.85 J g−1 of heat storage during heating and 103.58 J g−1 of heat release during cooling. Multiple heating and cooling cycles showed that the composite films maintained their thermal management functionality after multiple heating-cooling cycles. The PCMs could be recovered with a yield of approximately 95% by the application of a simple dissolution and filtration process. The morphology, chemical structure, and thermal properties of the PCMs were maintained after the recovery process. The bio-based composite films with thermal management functionality and recyclability are proposed as an innovative, practical, and effective system for thermoactive storage and packaging applications.

1. Introduction

Packaging materials produced by using non-biodegradable synthetic polymers cause significant environmental problems. Bio-based polymers have drawn great attention in the last decade due to rising environmental concerns about the inappropriate disposal of plastics, the limitations of petroleum-based polymers, and the high price of oil. As a result, the focus of research has shifted to the development of eco-friendly and sustainable packaging materials [1,2,3,4]. Pullulan is an exopolysaccharide obtained from the yeast-like fungus Aureobasidium for commercial use. Because of the low degree of hydrogen bonding in its crystal form, it is easily water-soluble. As a water-soluble and non-toxic biopolymer with superior film-forming and adhesive properties, it offers great potential to produce films and coatings for packaging applications. Solvent casting, extrusion, coating, layer-by-layer assembly, and electrospinning are the main methods used to fabricate pullulan-based films/coatings. Aqueous solutions with pullulan concentrations of 2%–20% make it possible to prepare films and coatings by dipping, spraying, or brushing. Pullulan has a wide range of applications in many fields such as food storage, health care, pharmacy, medical, biomedical, and even lithography [1].
The addition of functional additives into the polymer matrix enables the production of nano/microcomposites with distinguishing functional properties. An increasing number of publications on the modification of pullulan with different types of additives are seen. Nanofibrillated cellulose [5], microfibrillated cellulose [6], lysozyme [7], montmorillonite [8,9], nanoSiO2 [2], nanosilver [10], and TiO2 [11] have been used to improve either structural or functional properties of pullulan films.
Depending on the medium temperature, PCMs are able to absorb, store, and release large amounts of latent heat due to their phase transition properties [12,13,14,15,16]. PCMs are categorized into three groups: organic, inorganic, and eutectics of the first two. Paraffin waxes, polyethylene glycols (PEGs), and fatty acids are organic PCMs, whereas metals, metal alloys, salts, and salt hydrates are inorganic PCMs. The melting temperature, temperature range of the phase-change, and heat storage capacity are important properties of the PCMs that determine the selection of the PCMs for a particular end use [16]. Leakage of PCM materials when they are in a melt state is a common problem with PCMs. They are usually not embedded into the structure of polymeric materials but are first encapsulated and then applied in the form of microencapsulated PCMs (microPCMs). Microencapsulation is an effective method to prevent the leakage of the PCMs and their reaction to the outside environment. Microcapsules are produced by coating a thin and resilient polymer onto small solid particles or liquid droplets [16,17,18,19]. The microencapsulation of PCMs results in some useful effects for heat storage, such as tailorable shape, favourable temperature gradient, and increased lifetime. Furthermore, the PCMs are always in a dried state as the phase change takes place within the coating layer. Microencapsulation increases the specific exchange area, which aids in effective heat transfer and avoids problems such as supercooling and phase separation. The walls protect the core materials from their environment prior to use, provide safe and convenient handling of core materials, and result in increased heat resistance [16].
Organic PCMs are used to produce novel materials with thermal management functionality for many different applications such as smart textiles [20], construction [21,22], photocatalytic applications [23], photovoltaic systems [24], biomedical applications [25], electrics and electronics [26], and packaging materials [27]. Recently, many novel approaches have appeared in the literature for the development of materials with thermal management properties. For example, researchers developed fibrous wearable strain sensors by decorating plant-extracted 3D porous Juncus effusus fibers with conductive graphene/polypyrrole which also showed electric-thermal properties. The fibers showed fast heating properties with the application of voltage. It could be possible to achieve a temperature of 147 °C at 10 V within 10 s [28]. In another study, a fiber membrane was fabricated using poly (vinylidene fluoride-co-hexafluoro propene) and polypyrrole. The membrane displayed multifunctional properties of radiative cooling and solar heating for efficient daytime outdoor thermal management. The multifunctional membrane presented a sun-ambient cooling temperature of ~ 4.5 °C and a super-ambient heating temperature of ~ 35.8 °C in an outdoor environment under the solar intensity of ~ 850 W m−2 [29]. The nanoprocessing of silk through a molecular bonding design and scalable coupling reagent-assisted method achieved sub-ambient daytime radiative cooling. In simulation studies, the temperature of skin covered with nanoprocessed silk showed a temperature 8 °C lower than skin covered with natural silk and cotton. The nanoprocessed silk fabric was durable even through water washing and sunlight drying. The study provided a sustainable, energy-saving method for personal thermal management and contributed to the field of green energy [30]. Other than the novel approaches to developing materials with thermal management properties, great effort is being invested in developing recyclable materials following the concept of “design for recycling”. In this study, pullulan-based, recyclable composite films with thermal management functionality were prepared with the incorporation of PCMs as alternative thermoactive packaging materials. Although many studies investigate and report the properties of PCMs and composite materials (coatings, films, fibers, and nanofibers) with PCMs, a very limited number of studies show the preparation of bio-based, easily recyclable films with thermal management properties. Pullulan is specifically chosen as a bio-based, water-soluble polymer that enables the easy application of its solutions by immersion, spraying, or brushing. Nextek 28D PCMs, which are microcapsules of melamine formaldehyde containing paraffin, were selected as shape-stable phase-changing materials and incorporated into pullulan films. The morphology, chemical structure, thermal properties, stability, and recyclability of biomicrocomposite films were analysed in detail. This study offers significant contribution to the efforts to “design for recycling” and the literature by showing the development of eco-friendly and recyclable thermoactive films which are chemically, morphologically, and thermally stable.

2. Experimental details

2.1. Materials

Food-grade pullulan with a molecular weight of 100 kDa was kindly provided by Hayashibara Biochemical Laboratories, Inc., and used for the preparation of neat and composite films. Pullulan polymer was dissolved in distilled water for film preparation. Nextek 28D phase-changing microcapsules with a peak melting point of 28 °C were kindly provided by Microtek Laboratories, Inc. (Moraine, OH, USA), and incorporated into the pullulan film structure to obtain biomicrocomposite films showing thermal management functionality. The properties of the Nextek 28D microcapsules are presented in Table 1. Ethyl acetate was used as the nonsolvent for the precipitation of pullulan during the recovery of pullulan in powder form.

2.2. Methods

2.2.1. Preparation of the Solutions

Distilled water was used as the solvent for dissolving pullulan. Certain amounts of PCMs added into certain amounts of distilled water were homogenized in an ultrasonic bath at room temperature for 30 min. Then pullulan was added and magnetically stirred at room temperature for 2 h until complete dissolution. The concentration of pullulan was 10 wt.% in the composite solutions. Reference films were also cast from 10 wt.% pullulan/distilled water solution. The photographs of the pullulan solution and composite pullulan solution containing 75 wt.% PCMs are presented in Figure 1.

2.2.2. Film Preparation

The amount of 20 mL of composite solutions containing different amounts of PCMs was cast on a petri dish and left at room temperature for drying. The PCM contents in the composite films based on film weight are presented in Table 2. The wt.% of PCMs based on the film weight can be seen in the table. “P” is used to denominate Pullulan, and “NEX” is used to denominate the phase change material, NEXTEK 28D. The schematic diagram showing the preparation of pullulan-based thermoactive films is presented in Figure 2.

2.2.3. Recycling Process Applied for the Recovery of Pullulan and PCMs

Distilled water was used to dissolve the P-NEX75 film (composite film containing 75 wt.% PCMs), and the solution was filtered through a standard laboratory filter paper for the recovery of the PCM particles and the polymer pullulan. After the filtration, the solution was added to ethyl acetate for the precipitation of pullulan in powder form. The recovered pullulan powder was analysed by FTIR to confirm that it did not contain any PCMs. The recovered PCM microcapsules were tested with regard to their morphology and thermal performance in order to ensure that they were reusable.

2.3. Characterization

2.3.1. Fourier Transform Infrared Spectrometer (FTIR)

FTIR (Perkin Elmer-Spectrum Two) with an ATR accessory was employed to record absorption spectra of pullulan polymer, encapsulated PCMs, and composite films in a range from 4000 to 600 cm−1 with a resolution of 4 cm−1. FTIR spectra of the samples were obtained by averaging 32 scans taken for each sample. The chemical structure of recovered pullulan and encapsulated PCMs were also analysed using FTIR spectroscopy.

2.3.2. Differential Scanning Calorimetry (DSC)

Mettler Toledo (Columbus, OH, USA) was used to investigate the thermal properties of pullulan, encapsulated PCMs, and composite films prepared. The latent heat storage and release ability of the materials were evaluated by testing in a temperature range from 0 °C to 50 °C, with a heating/cooling rate of 5 °C min−1, under nitrogen (N2) with a flow rate of 20 mL min−1. All samples were brought to thermal equilibrium at the starting temperature, held for 10 min, then heated to the final temperature of a 5 °C min−1 heating rate where they were held for 10 min. The thermal characteristics were evaluated from the second heating of the samples. The peak points of the phase transition regions were taken as the phase transition temperature. The areas under the solid–liquid and liquid–solid phase change peaks were calculated to determine the melting enthalpy (ΔHm) and crystallization enthalpy (ΔHc), respectively. DSC was also utilized to confirm the thermal stability of the recovered PCMs following the same testing procedure.

2.3.3. Thermal Stability

Fifty consecutive heating-cooling cycles between 0 and 50 °C with a heating rate of 5 °C min−1 were applied to the composite film containing 75 wt.% PCMs to evaluate the changes in the latent heat storage and release ability of the composite film by repeated thermal cycles. The process also was used to confirm the thermal stability of the pullulan-based thermoactive films. The phase transition temperature was taken as the peak point of the DSC curves. The areas under the solid–liquid and liquid–solid phase change peaks were calculated to determine the ΔHm and ΔHc, respectively.

2.3.4. Optical Microscope (OM)

An Olympus BX51 optical microscope manufactured by Olympus Corporation (Tokyo, Japan) was used to confirm the form stability of PCM microcapsules after the recovery process.

3. Results and Discussion

3.1. Pullulan-Based Thermoactive Films

3.1.1. Appearance of the Films Prepared

Photographs of neat pullulan and composite pullulan films containing 75 wt.% encapsulated PCMs are presented in Figure 3. Both films were smooth. The composite films turned to a white colour with the addition of the microcapsules.

3.1.2. Fourier Transform Infrared Spectroscopy (FTIR)

FTIR spectroscopy was used to confirm the incorporation of PCM into the pullulan film structure. Additionally, the spectra were used to compare the differences between the chemical structure of composite films and the neat pullulan films. The normalized FTIR spectra of PCMs (Nextek 28D) and pullulan powder used in the preparation of the films are presented in Figure 4, while the FTIR spectra of the composite films are presented in Figure 5.
The composite films were expected to display absorbance signals corresponding to the molecular structure of pullulan, crosslinked melamine formaldehyde, and paraffin. Pullulan is a linear homopolysaccharide, the building block of which is a maltotriose. Maltotriose units are bonded to each other by α-(1,6) bonds and three glucose units of maltotriose are bonded through α-(1,4) glycosidic bonds to another three glucose units of maltotriose to form the pullulan repeating unit. For pullulan, a broad peak located at around 3330 cm−1 was assigned to -OH stretching vibrations which is extensively observed in the polysaccharide structures. The peak around 2924 cm−1 corresponded to the C–H vibrations of methyl groups, including CH2 and CH3 [31,32,33]. In addition, only a single peak at 1642 cm−1 was assigned to the stretching vibration of O–C–O in pullulan. Other features of pullulan were also observed in the spectra, including C–OH bend (1354 cm−1) and C–O–C stretch (1148 cm−1). The peaks at 1076 and 1020 cm−1 were attributed to the vibration of C–O–H and C–O bands, respectively. The typical absorption bands for the α-configuration of α-D-glucopyranoside units in pullulan were observed at 851 cm−1. In addition, the two main linkages of pullulan (i.e., α-(1,4) and α-(1,6)-D-glycosidic bonds) were observed at 738 and 918 cm−1 [34,35,36,37,38,39,40]. Nextek 28D is a PCM material that consists of a highly-crosslinked melamine formaldehyde shell containing paraffin in the core. Therefore, peaks related to both highly-crosslinked formaldehyde and paraffin are expected to be observed in the FTIR spectrum of the PCMs. In the spectrum of Nextek 28D, the peak at 3337 cm−1 may be assigned to the O-H and shows the presence of moisture in the PCMs. Paraffins show bands located at 2954, 2914, and 2848 cm−1 corresponding to the characteristic peaks of the aliphatic C–H stretching vibrations. The peak at 1470 cm−1 was assigned to the bending vibration of the -CH2 groups, and 716 cm−1 to the rocking vibrations of C–H in the paraffin [41]. Crosslinked melamine formaldehydes give FTIR absorbance signals at 3335 cm−1, which can be assigned to the secondary amine vibrations; between 2940 and 2915 cm−1 to asymmetric stretching vibrations; and between 2870 and 2840 cm−1 to the symmetric stretching vibrations of CH2 groups. These all overlap with those coming from the CH2 groups of the paraffins. The peaks at 1551 cm−1 are attributed to the stretching of triazine rings. Peaks at 1470 cm−1 are expected to appear due to several C–H vibrations [42]. The band at 1157 cm−1 corresponds to CR–N stretching and asymmetrical C–O–C stretching vibration in -CH2–O–CH2- group. The bands between 1360 and 1320 in MF resins are assigned to the sidegroup-sensitive CAR–N stretching vibrations, while the band at 891 cm−1 is assigned to the -CH2 twisting vibration [42].
The spectra of composite films were normalized to the largest peak observed, namely the C–O stretchings observed at 1020 cm−1, in order to be able to show the changes in the intensities of the PCM-related peaks with the changes in PCM contents. According to Figure 5, remarkable differences in spectra profiles were detected between pure pullulan films and composite films. The absorption bands observed in the spectra of the composite films were a combination of the pullulan polymer and highly crosslinked PCMs. The absorbance values of the peaks, which were related to PCMs, increased with the increase in the PCM content. Showing the typical peaks of PCMs in addition to the typical peaks of pullulan, the FTIR spectra of composite films confirmed the incorporation of PCMs into the pullulan films. As there were no significant shifts in the locations of the peaks, it was concluded that no chemical reactions occurred between pullulan polymer and PCMs.

3.1.3. Thermal Management Functionality

Thermal management properties of PCM materials are effectively tested by using DSC. The amount of energy that can be stored and released by a material can be determined by applying heating and cooling cycles within a certain temperature range. The melting enthalpy shows the amount of energy that can be stored, and the crystallization enthalpy shows the energy that can be released [43]. For packaging materials with thermal management functionality, proper phase-change temperature and high latent heat storage capability is the most important characteristic. In this study PCM material, which displayed a melting point of around 28 °C was specially chosen. The pullulan polymer, encapsulated PCMs, and pullulan-based thermoactive films containing encapsulated PCMs were characterised with regard to their thermal properties, i.e., melting temperature (Tm), melting enthalpy (ΔHm), crystallization temperature (Tc), and crystallization enthalpy (ΔHc) via DSC. DSC thermograms of pullulan powder and encapsulated PCMs are presented in Figure 6, while the DSC thermograms of pullulan-based films and pullulan-based thermoactive composite films are presented in Figure 7.
While neat pullulan powder showed no phase transitions between 0 and 50 °C, encapsulated PCMs displayed a large exothermic (crystallization) peak between around 25 and 35 °C and an endothermic peak at around 28 °C. The melting and crystallization enthalpies of the encapsulated PCMs were measured as 173.26 and 170.50 J g−1, respectively. Thermal properties of the pullulan-based thermoactive films were expected to be dominated by the PCM type and PCM content. The phase-change temperatures and the possible maximum value of the latent heat were to be determined by the PCM type, whereas the actual value of the latent heat was expected to be determined by the PCM content of the composite films.
According to the FTIR analysis, no interactions occurred between the polymer and the PCMs. Pullulan-based thermoactive composite films showed phase change because of the encapsulated PCMs in the film structure, and no additional effects were expected as there were no interactions between the components of the composite films. The corresponding phase transition temperatures and enthalpy values of composite films are summarized in Table 3. The phase change temperatures (Tm and Tc) of the films were dominated by the PCM properties and showed no obvious variations compared to those of the PCMs. The slight increase in the melting temperature and the crystallization temperature with the increase in the additive content was likely due to the differences in the thermal conductivity properties of the polymer and PCMs. An increase in the PCM concentration resulted in an increase in the storage and release enthalpy values. The ΔHm increased from 21.94 to 104.85 J g−1, whereas ΔHc increased from 20.92 to 103.58 J g−1 as the PCM content increased from 15 to 75 wt.%. The highest storing and releasing enthalpy values were obtained for the pullulan-based thermoactive films with the highest content of PCMs. Preparing PAN nanofibers with 50 wt.% paraffinic PCMs, Kizildag et al. reported that the composite nanofibers showed storage and release enthalpies of 58.74 J g−1 and 57.41 J g−1, respectively [44]. In another study, a shape-stabilized and flexible phase change film was prepared based on polyethylene glycol (PEG), which was stabilized by the cooperation of cellulose nanofibers (CNF) and expanded graphite (EG). The thermal conductivity of the prepared film was enhanced by boron nitride (BN). The results showed that the phase change enthalpy of the film could reach 79.46 J g−1 and remained almost unchanged during 40 heating–cooling cycles [45]. The thermoregulation performances obtained for the pullulan-based composite films with PCMs were in parallel with the results reported in the literature.
The enthalpy values of pullulan-based thermoactive films were lower than that of encapsulated PCMs because the polymer (pullulan) in the composite films did not have any phase transitions in the temperature range between 5 and 50 °C. Additionally, some differences were observed in the enthalpy values measured for the composite films and theoretical enthalpy values calculated. The theoretical and experimental enthalpy values obtained by DSC are presented in Table 4. Theoretical enthalpy values of the composite films were calculated by multiplying the melting/crystallization enthalpy and mass percentage of the PCM in the composite film. From Table 4, all the experimental values of enthalpy were lower than the corresponding theoretical values, and the efficiency of enthalpy, which was calculated as the ratio of the experimental value to the theoretical values, was less than 100%. The differences between the experimental values and theoretical values were attributed to the hindrance of pullulan by acting as a diluent for the PCMs and preventing them to form well-defined structures in the composite films [44].

3.1.4. Stability Analysis—Repeated Heating & Cooling Cycles

The thermal stability of pullulan-based thermoactive film containing 75 wt.% PCMs (P-NEX75) was tested by applying 50 consecutive thermal cycles. The thermograms of the first and fiftieth cycles are presented in Figure 8a. In the inset, the thermograms of 50 cycles are presented. The changes in melting, crystallization enthalpies, and phase-change temperatures are presented in Figure 8b. The long-term stability of the pullulan-based thermoactive films was confirmed as no significant changes were observed in the phase transition temperatures and enthalpies. Additionally, the thermal cycles applied showed that no thermal evaporation (thus no PCM loss) took place during the repeated cycles. Furthermore, the application of thermal cycles indicated that the thermal properties of the composite films were almost unchanged after the test completion.

3.2. Recovery of Pullulan and PCMs

Pullulan-based thermoactive film containing 75 wt.% PCMs was dissolved in distilled water, and the solution was filtered through a standard laboratory filter paper for the recovery of the PCM particles and the polymer pullulan. After the filtration, the solution was added to ethyl acetate for the precipitation of pullulan in powder form. The recovered pullulan powder was analysed by FTIR to confirm that it did not contain any PCMs. The recovered PCM microcapsules were tested with regard to their morphology and thermal performance in order to ensure that they were reusable. The PCMs and pullulan polymer could be recovered with a yield of approximately 95% and 93% respectively. The optical microscope images, FTIR spectra, and DSC thermograms of the recovered PCMs in comparison to the original PCMs showed that the morphology, chemical structure, and thermal properties of the recovered PCMs were maintained after the recovery process All of these results showed that the PCMs were reusable (Figure 9a–c). The FTIR spectrum of the recovered pullulan was identical to the fresh pullulan polymer (Figure 10).

4. Conclusions

Recyclable bio-based films with thermal management functionality using pullulan as the matrice polymer and Nextek 28D microcapsules as the PCM material were prepared. Uniform films with uniformly dispersed PCMs were obtained via the film-casting method. The composite films were white in colour. While neat pullulan films showed no phase transitions between 0 and 50 °C, pullulan-based composite films showed melting and crystallization due to the presence of encapsulated PCMs. While the phase transition temperatures of the films showed no apparent variations compared to that of PCMs, the enthalpy values of the bio-based films increased with the increase in the PCM content. The melting enthalpy increased from 21.94 to 104.85 J g−1, and the crystallization enthalpy increased from 20.92 to 103.58 J g−1 as the PCM content increased from 15 to 75 wt.%. The composite films prepared with 75 wt.% PCM incorporation exhibited 104.85 J g−1 of enthalpy storage during heating with 80.7% efficiency. The crystallization enthalpy was 103.58 J g−1 with an efficiency of 81%. Additionally, the application of thermal cycles indicated that the bio-based composite films showed good thermal reliability as their thermal properties were well retained after thermal cycling. The PCMs and pullulan polymer could be recovered with a yield of approximately 95% and 93% respectively. The morphology, chemical structure, and thermal properties of the PCMs were maintained after the recovery process, which showed the reusability of the PCMs. The chemical structure of the recovered pullulan was identical to that of the fresh pullulan polymer. The easily applicable bio-based composite films with thermal management functionality and recyclability appeared to provide an innovative system for packaging and storage applications.

Funding

This research received no external funding.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The data presented in this study are available on request from the corresponding author.

Conflicts of Interest

The author declares no competing interest.

References

  1. Kraśniewska, K.; Pobiega, K.; Gniewosz, M. Pullulan-Biopolymer with Potential for Use as Food Packaging. Int. J. Food Eng. 2019, 15, 20190030. [Google Scholar] [CrossRef]
  2. Hassannia-Kolaee, M.; Khodaiyan, F.; Pourahmad, R.; Shahabi-Ghahfarrokhi, I. Development of Ecofriendly Bionanocomposite: Whey Protein Isolate/Pullulan Films with Nano-SiO2. Int. J. Biol. Macromol. 2016, 86, 139–144. [Google Scholar] [CrossRef]
  3. Shahabi-Ghahfarrokhi, I.; Khodaiyan, F.; Mousavi, M.; Yousefi, H. Preparation of UV-Protective Kefiran/Nano-ZnO Nanocomposites: Physical and Mechanical Properties. Int. J. Biol. Macromol. 2015, 72, 41–46. [Google Scholar] [CrossRef]
  4. Rhim, J.W.; Lee, S.B.; Hong, S.I. Preparation and Characterization of Agar/Clay Nanocomposite Films: The Effect of Clay Type. J. Food Sci. 2011, 76, N40–N48. [Google Scholar] [CrossRef] [PubMed]
  5. Trovatti, E.; Fernandes, S.C.M.; Rubatat, L.; Perez, D.d.S.; Freire, C.S.R.; Silvestre, A.J.D.; Neto, C.P. Pullulan-Nanofibrillated Cellulose Composite Films with Improved Thermal and Mechanical Properties. Compos. Sci. Technol. 2012, 72, 1556–1561. [Google Scholar] [CrossRef]
  6. Cozzolino, C.A.; Cerri, G.; Brundu, A.; Farris, S. Microfibrillated Cellulose (MFC): Pullulan Bionanocomposite Films. Cellulose 2014, 21, 4323–4335. [Google Scholar] [CrossRef]
  7. Silva, N.H.C.S.; Vilela, C.; Almeida, A.; Marrucho, I.M.; Freire, C.S.R. Pullulan-Based Nanocomposite Films for Functional Food Packaging: Exploiting Lysozyme Nanofibers as Antibacterial and Antioxidant Reinforcing Additives. Food Hydrocoll. 2018, 77, 921–930. [Google Scholar] [CrossRef]
  8. Introzzi, L.; Fuentes-Alventosa, J.J.; Cozzolino, C.A.; Trabattoni, S.; Tavazzi, S.; Bianchi, C.L.; Schiraldi, A.; Piergiovanni, L.; Farris, S. “Wetting Enhancer” Pullulan Coating for Antifog Packaging Applications. ACS Appl. Mater. Interfaces 2012, 4, 3692–3700. [Google Scholar] [CrossRef]
  9. Hassannia-Kolaee, M.; Khodaiyan, F.; Shahabi-Ghahfarrokhi, I. Modification of Functional Properties of Pullulan-Whey Protein Bionanocomposite Films with Nanoclay. J. Food Sci. Technol. 2016, 53, 1294–1302. [Google Scholar] [CrossRef]
  10. Pinto, R.J.B.; Almeida, A.; Fernandes, S.C.M.; Freire, C.S.R.; Silvestre, A.J.D.; Neto, C.P.; Trindade, T. Antifungal Activity of Transparent Nanocomposite Thin Films of Pullulan and Silver against Aspergillus Niger. Colloids Surf. B Biointerfaces 2013, 103, 143–148. [Google Scholar] [CrossRef]
  11. Liu, Y.; Liu, Y.; Han, K.; Cai, Y.; Ma, M.; Tong, Q.; Sheng, L. Effect of Nano-TiO2 on the Physical, Mechanical and Optical Properties of Pullulan Film. Carbohydr. Polym. 2019, 218, 95–102. [Google Scholar] [CrossRef] [PubMed]
  12. Ho, C.P.; Fan, J.; Newton, E.; Au, R. Improving Thermal Comfort in Apparel. In Improving Comfort in Clothing; Song, G., Ed.; Woodhead Publishing: Cambridge, UK, 2011; pp. 165–181. ISBN 978-1-84569-539-2. [Google Scholar]
  13. Das, A.; Alagirusamy, R. Introduction to Clothing Comfort. In Science in Clothing Comfort; Das, A., Alagirusamy, R., Eds.; Woodhead Publishing India: New Delhi, India, 2010; pp. 1–12. ISBN 978-1-84569-789-1. [Google Scholar]
  14. Erkan, G. Enhancing The Thermal Properties of Textiles With Phase Change Materials. Res. J. Text. Appar. 2004, 8, 57–64. [Google Scholar] [CrossRef]
  15. Mondal, S. Phase Change Materials for Smart Textiles—An Overview. Appl. Therm. Eng. 2008, 28, 1536–1550. [Google Scholar] [CrossRef]
  16. Sarier, N.; Onder, E. Organic Phase Change Materials and Their Textile Applications: An Overview. Thermochim. Acta 2012, 540, 7–60. [Google Scholar] [CrossRef]
  17. Alay, S.; Alkan, C.; Göde, F. Synthesis and Characterization of Poly(Methyl Methacrylate)/n-Hexadecane Microcapsules Using Different Cross-Linkers and Their Application to Some Fabrics. Thermochim. Acta 2011, 518, 1–8. [Google Scholar] [CrossRef]
  18. Nelson, G. Application of Microencapsulation in Textiles. Int. J. Pharm. 2002, 242, 55–62. [Google Scholar] [CrossRef] [PubMed]
  19. Sarier, N.; Onder, E. The Manufacture of Microencapsulated Phase Change Materials Suitable for the Design of Thermally Enhanced Fabrics. Thermochim. Acta 2007, 452, 149–160. [Google Scholar] [CrossRef]
  20. Zhang, W.; Hao, S.; Zhao, D.; Bai, G.; Zuo, X.; Yao, J. Preparation of PMMA/SiO2 PCM Microcapsules and Its Thermal Regulation Performance on Denim Fabric. Pigment Resin Technol. 2020, 49, 491–499. [Google Scholar] [CrossRef]
  21. Marani, A.; Nehdi, M.L. Integrating Phase Change Materials in Construction Materials: Critical Review. Constr. Build. Mater. 2019, 217, 36–49. [Google Scholar] [CrossRef]
  22. Mohaisen, K.O.; Hasan Zahir, M.; Maslehuddin, M.; Al-Dulaijan, S.U. Development of a Shape-Stabilized Phase Change Material Utilizing Natural and Industrial Byproducts for Thermal Energy Storage in Buildings. J. Energy Storage 2022, 50, 104205. [Google Scholar] [CrossRef]
  23. Liu, H.; Wang, X.; Wu, D.; Ji, S. Fabrication and Applications of Dual-Responsive Microencapsulated Phase Change Material with Enhanced Solar Energy-Storage and Solar Photocatalytic Effectiveness. Sol. Energy Mater. Sol. Cells 2019, 193, 184–197. [Google Scholar] [CrossRef]
  24. Choubineh, N.; Jannesari, H.; Kasaeian, A. Experimental Study of the Effect of Using Phase Change Materials on the Performance of an Air-Cooled Photovoltaic System. Renew. Sustain. Energy Rev. 2019, 101, 103–111. [Google Scholar] [CrossRef]
  25. Mondieig, D.; Rajabalee, F.; Laprie, A.; Oonk, H.A.J.; Calvet, T.; Cuevas-Diarte, M.A. Protection of Temperature Sensitive Biomedical Products Using Molecular Alloys as Phase Change Material. Transfus. Apher. Sci. 2003, 28, 143–148. [Google Scholar] [CrossRef] [PubMed]
  26. Kandasamy, R.; Wang, X.Q.; Mujumdar, A.S. Application of Phase Change Materials in Thermal Management of Electronics. Appl. Therm. Eng. 2007, 27, 2822–2832. [Google Scholar] [CrossRef]
  27. Singh, S.; Gaikwad, K.; Youn, S.L. Phase Change Materials for Advanced Cooling Packaging. Environ. Chem. Lett. 2018, 16, 845–859. [Google Scholar] [CrossRef]
  28. Gong, J.; Tang, W.; Xia, L.; Fu, Z.; Zhou, S.; Zhang, J.; Zhang, C.; Hua Ji, L.L.; Xu, W. Flexible and weavable 3D porous graphene/PPy/lignocellulose-based versatile fibrous wearables for thermal management and strain sensing. Chem. Eng. J. 2023, 452, 139338. [Google Scholar] [CrossRef]
  29. Xiang, B.; Zhang, R.; Zeng, X.; Yanlong, L.; Zhenyang, L. An Easy-to-Prepare Flexible Dual-Mode Fiber Membrane for Daytime Outdoor Thermal Management. Adv. Fiber Mater. 2022, 4, 1058–1068. [Google Scholar] [CrossRef]
  30. Pan, S.; Zhu, M. Nanoprocessed Silk Makes Skin Feel Cool. Adv. Fiber Mater. 2022, 4, 319–320. [Google Scholar] [CrossRef]
  31. Choudhury, A.R.; Saluja, P.; Prasad, G.S. Pullulan Production by an Osmotolerant Aureobasidium Pullulans RBF-4A3 Isolated from Flowers of Caesulia Axillaris. Carbohydr. Polym. 2011, 83, 1547–1552. [Google Scholar] [CrossRef]
  32. Terán Hilares, R.; Orsi, C.A.; Ahmed, M.A.; Marcelino, P.F.; Menegatti, C.R.; da Silva, S.S.; dos Santos, J.C. Low-Melanin Containing Pullulan Production from Sugarcane Bagasse Hydrolysate by Aureobasidium Pullulans in Fermentations Assisted by Light-Emitting Diode. Bioresour. Technol. 2017, 230, 76–81. [Google Scholar] [CrossRef]
  33. Hamidi, M.; Kennedy, J.F.; Khodaiyan, F.; Mousavi, Z.; Hosseini, S.S. Production Optimization, Characterization and Gene Expression of Pullulan from a New Strain of Aureobasidium Pullulans. Int. J. Biol. Macromol. 2019, 138, 725–735. [Google Scholar] [CrossRef] [PubMed]
  34. Li, Q.M.; Wang, J.F.; Zha, X.Q.; Pan, L.H.; Zhang, H.L.; Luo, J.P. Structural Characterization and Immunomodulatory Activity of a New Polysaccharide from Jellyfish. Carbohydr. Polym. 2017, 159, 188–194. [Google Scholar] [CrossRef] [PubMed]
  35. Wu, J.; Zhong, F.; Li, Y.; Shoemaker, C.F.; Xia, W. Preparation and Characterization of Pullulan-Chitosan and Pullulan-Carboxymethyl Chitosan Blended Films. Food Hydrocoll. 2013, 30, 82–91. [Google Scholar] [CrossRef]
  36. Niu, B.; Shao, P.; Chen, H.; Sun, P. Structural and Physiochemical Characterization of Novel Hydrophobic Packaging Films Based on Pullulan Derivatives for Fruits Preservation. Carbohydr. Polym. 2019, 208, 276–284. [Google Scholar] [CrossRef]
  37. Cheng, K.-C.; Demirci, A.; Catchmark, J.M. Effects of Plastic Composite Support and PH Profiles on Pullulan Production in a Biofilm Reactor. Appl. Microbiol. Biotechnol. 2010, 86, 853–861. [Google Scholar] [CrossRef] [PubMed]
  38. Trovatti, E.; Fernandes, S.C.M.; Rubatat, L.; Freire, C.S.R.; Silvestre, A.J.D.; Carlos, P.N. Sustainable Nanocomposite Films Based on Bacterial Cellulose and Pullulan. Cellulose 2012, 19, 729–737. [Google Scholar] [CrossRef]
  39. Kumar, V.; Mirzaei, A.; Bonyani, M.; Kim, K.-H.; Kim, H.W.; Kim, S.S. Advances in Electrospun Nanofiber Fabrication for Polyaniline (PANI)-Based Chemoresistive Sensors for Gaseous Ammonia. TRAC Trends Anal. Chem. 2020, 129, 115938. [Google Scholar] [CrossRef]
  40. Mirzaee, H.; Khodaiyan, F.; Kennedy, J.F.; Hosseini, S.S. Production, Optimization and Characterization of Pullulan from Sesame Seed Oil Cake as a New Substrate by Aureobasidium Pullulans. Carbohydr. Polym. Technol. Appl. 2020, 1, 100004. [Google Scholar] [CrossRef]
  41. Liang, R.; Hu, A.; Hatat-Fraile, M.; Zhou, N. Fundamentals on Adsorption, Membrane Filtration, and Advanced Oxidation Processes for Water Treatment. In Nanotechnology for Water Treatment and Purification; Hu, A., Apblett, A., Eds.; Springer: Cham, Switzerland, 2014; Volume 22, pp. 1–45. ISBN 978-3-319-06577-9. [Google Scholar] [CrossRef]
  42. Weiss, S.; Urdl, K.; Mayer, H.A.; Zikulnig-Rusch, E.M.; Kandelbauer, A. IR Spectroscopy: Suitable Method for Determination of Curing Degree and Crosslinking Type in Melamine–Formaldehyde Resins. J. Appl. Polym. Sci. 2019, 136, 47691. [Google Scholar] [CrossRef]
  43. Krupa, I.; Nógellová, Z.; Špitalský, Z.; Janigová, I.; Boh, B.; Sumiga, B.; Kleinová, A.; Karkri, M.; AlMaadeed, M.A. Phase Change Materials Based on High-Density Polyethylene Filled with Microencapsulated Paraffin Wax. Energy Convers. Manag. 2014, 87, 400–409. [Google Scholar] [CrossRef]
  44. Kizildag, N. Smart Composite Nanofiber Mats with Thermal Management Functionality. Sci. Rep. 2021, 11, 4256. [Google Scholar] [CrossRef] [PubMed]
  45. He, Y.; Li, H.; Luo, F.; Jin, Y.; Huang, B.; Qingrong, Q. Bio-based flexible phase change composite film with high thermal conductivity for thermal energy storage Composites Part A. Appl. Sci. Manuf. 2021, 151, 106638. [Google Scholar] [CrossRef]
Coatings 13 00414 g001 550
Figure 1. Photographs of (a) pullulan solution and (b) composite solution.
Figure 1. Photographs of (a) pullulan solution and (b) composite solution.
Coatings 13 00414 g001
Coatings 13 00414 g002 550
Figure 2. Schematic diagram showing the preparation of the pullulan-based composite films.
Figure 2. Schematic diagram showing the preparation of the pullulan-based composite films.
Coatings 13 00414 g002
Coatings 13 00414 g003 550
Figure 3. Photographs of (a) neat pullulan film and (b) composite film with 75 wt.% PCMs.
Figure 3. Photographs of (a) neat pullulan film and (b) composite film with 75 wt.% PCMs.
Coatings 13 00414 g003
Coatings 13 00414 g004 550
Figure 4. FTIR spectra of PCMs (Nextek 28D) and neat pullulan powder.
Figure 4. FTIR spectra of PCMs (Nextek 28D) and neat pullulan powder.
Coatings 13 00414 g004
Coatings 13 00414 g005 550
Figure 5. FTIR spectra of composite films at (a) 4000 to 600 cm−1 range; (b) 3000 to 2750 cm−1 range.
Figure 5. FTIR spectra of composite films at (a) 4000 to 600 cm−1 range; (b) 3000 to 2750 cm−1 range.
Coatings 13 00414 g005
Coatings 13 00414 g006a 550Coatings 13 00414 g006b 550
Figure 6. Three cycle heating and cooling curves of (a) Pullulan and (b) encapsulated PCMs (Nextek 28D).
Figure 6. Three cycle heating and cooling curves of (a) Pullulan and (b) encapsulated PCMs (Nextek 28D).
Coatings 13 00414 g006aCoatings 13 00414 g006b
Coatings 13 00414 g007 550
Figure 7. Heating and cooling curves of pullulan and pullulan-based thermoactive films.
Figure 7. Heating and cooling curves of pullulan and pullulan-based thermoactive films.
Coatings 13 00414 g007
Coatings 13 00414 g008 550
Figure 8. (a) DSC curves of 1st and 50th thermal cycles with thermograms of 50 thermal cycles presented in the inset; (b) variations in storage and release enthalpies and thermal transition temperatures during thermal cycles for composite films containing 75 wt.% PCM (P-NEX75).
Figure 8. (a) DSC curves of 1st and 50th thermal cycles with thermograms of 50 thermal cycles presented in the inset; (b) variations in storage and release enthalpies and thermal transition temperatures during thermal cycles for composite films containing 75 wt.% PCM (P-NEX75).
Coatings 13 00414 g008
Coatings 13 00414 g009a 550Coatings 13 00414 g009b 550
Figure 9. Optical microscope images of (a) original PCMs; (b) recovered PCMs; (c) FTIR spectra; (d) DSC thermograms of recovered PCM microcapsules in comparison to original PCM microcapsules.
Figure 9. Optical microscope images of (a) original PCMs; (b) recovered PCMs; (c) FTIR spectra; (d) DSC thermograms of recovered PCM microcapsules in comparison to original PCM microcapsules.
Coatings 13 00414 g009aCoatings 13 00414 g009b
Coatings 13 00414 g010 550
Figure 10. FTIR spectrum of recovered pullulan in comparison to fresh pullulan polymer.
Figure 10. FTIR spectrum of recovered pullulan in comparison to fresh pullulan polymer.
Coatings 13 00414 g010
Table
Table 1. Properties of Nextek 28D microcapsules.
Table 1. Properties of Nextek 28D microcapsules.
PropertiesNextek 28D
AppearanceWhite to slightly off-white color
FormDry powder (>97 solids)
Particle size (mean)15–30 micron
Free wax content<2.5%
Melting point
Heat of fusion		28 °C (±2 °C)
>155 J/g
Table
Table 2. Formulations of the pullulan-based thermoactive films.
Table 2. Formulations of the pullulan-based thermoactive films.
SamplesPCM Content (wt.%)
(Based on Film Weight)
P-
P-NEX1515
P-NEX3030
P-NEX4545
P-NEX6060
P-NEX7575
Table
Table 3. Thermal properties of pullulan and pullulan-based thermoactive films between 0 and 50 °C.
Table 3. Thermal properties of pullulan and pullulan-based thermoactive films between 0 and 50 °C.
SamplesMelting Temp.
(°C)		Latent Heat of Melting
(ΔHm) (J g−1)		Crystallization Temp.
(°C)		Latent Heat of Crystallization (ΔHc) (J g−1)
neat Pullulan----
P-NEX1527.0421.9418.23/22.0420.92
P-NEX3027.8637.6518.79/22.0237.69
P-NEX4528.5066.5417.96/20.7365.41
P-NEX6029.4787.8315.70/20.5685.67
P-NEX7529.36104.8516.02/18.82103.58
Table
Table 4. Theoretical and experimental enthalpy values.
Table 4. Theoretical and experimental enthalpy values.
Theoretical Value (ΔHm)
(J g−1)		Experimental Value (ΔHm)
(J g−1)		%Theoretical Value (ΔHc)
(J g−1)		Experimental Value (ΔHc)
(J g−1)		%
P-NEX1525.9921.9484.425.5820.9281.8
P-NEX3051.9837.6572.451.1537.6973.7
P-NEX4577.9766.5485.376.7365.4184.8
P-NEX60104.0087.8384.5102.3085.4683.5
P-NEX75129.95104.8580.7127.88103.5881.0
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Kizildag, N. Pullulan Films with PCMs: Recyclable Bio-Based Films with Thermal Management Functionality. Coatings 2023, 13, 414. https://doi.org/10.3390/coatings13020414

AMA Style

Kizildag N. Pullulan Films with PCMs: Recyclable Bio-Based Films with Thermal Management Functionality. Coatings. 2023; 13(2):414. https://doi.org/10.3390/coatings13020414

Chicago/Turabian Style

Kizildag, Nuray. 2023. "Pullulan Films with PCMs: Recyclable Bio-Based Films with Thermal Management Functionality" Coatings 13, no. 2: 414. https://doi.org/10.3390/coatings13020414

APA Style

Kizildag, N. (2023). Pullulan Films with PCMs: Recyclable Bio-Based Films with Thermal Management Functionality. Coatings, 13(2), 414. https://doi.org/10.3390/coatings13020414

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop