Next Article in Journal
Automatic and Efficient Fall Risk Assessment Based on Machine Learning
Next Article in Special Issue
Behavioural Classification of Cattle Using Neck-Mounted Accelerometer-Equipped Collars
Previous Article in Journal
Facile Synthesis of Polyaniline/Carbon-Coated Hollow Indium Oxide Nanofiber Composite with Highly Sensitive Ammonia Gas Sensor at the Room Temperature
Previous Article in Special Issue
Toward the Next Generation of Digitalization in Agriculture Based on Digital Twin Paradigm
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Sensors
Volume 22
Issue 4
10.3390/s22041571
sensors-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Proposing UGV and UAV Systems for 3D Mapping of Orchard Environments

by
Aristotelis C. Tagarakis
1,*,
Evangelia Filippou
1,
Damianos Kalaitzidis
1,
Lefteris Benos
1,
Patrizia Busato
2 and
Dionysis Bochtis
1,3,*
1
Institute for Bio-Economy and Agri-Technology (IBO), Centre for Research and Technology-Hellas (CERTH), 6th km Charilaou-Thermi Rd, GR 57001 Thessaloniki, Greece
2
Department of Agriculture, Forestry and Food Science (DISAFA), University of Turin, Largo Braccini 2, 10095 Grugliasco, Italy
3
FarmB Digital Agriculture P.C., Doiranis 17, GR 54639 Thessaloniki, Greece
*
Authors to whom correspondence should be addressed.
Sensors 2022, 22(4), 1571; https://doi.org/10.3390/s22041571
Submission received: 26 December 2021 / Revised: 13 February 2022 / Accepted: 14 February 2022 / Published: 17 February 2022
(This article belongs to the Collection Sensors and Robotics for Digital Agriculture)
Browse Figures
Versions Notes

Abstract

:
During the last decades, consumer-grade RGB-D (red green blue-depth) cameras have gained popularity for several applications in agricultural environments. Interestingly, these cameras are used for spatial mapping that can serve for robot localization and navigation. Mapping the environment for targeted robotic applications in agricultural fields is a particularly challenging task, owing to the high spatial and temporal variability, the possible unfavorable light conditions, and the unpredictable nature of these environments. The aim of the present study was to investigate the use of RGB-D cameras and unmanned ground vehicle (UGV) for autonomously mapping the environment of commercial orchards as well as providing information about the tree height and canopy volume. The results from the ground-based mapping system were compared with the three-dimensional (3D) orthomosaics acquired by an unmanned aerial vehicle (UAV). Overall, both sensing methods led to similar height measurements, while the tree volume was more accurately calculated by RGB-D cameras, as the 3D point cloud captured by the ground system was far more detailed. Finally, fusion of the two datasets provided the most precise representation of the trees.

1. Introduction

1.1. General Context of RGB-Depth Cameras

Many tasks such as mapping, localization, navigation, 3D reconstruction of object, or scenery, among others, involve computer vision. Computer vision could be described as the technology that combines image processing through computational algorithms to obtain certain information from images [1,2,3] or vision systems utilizing laser scanners [4]. Focusing on the former case, a lot of studies have used RGB cameras so as to locate and distinguish the targets (e.g., fruits) from other objects by exploiting, for example, the shape, the color and the texture, usually combining their images with machine learning [3,5,6]. However, RGB cameras can only get two-dimensional (2D) information of the scene, while they are susceptible to variable light conditions and occlusions [7]. These challenges have been overcome through acquiring depth measurements of higher resolution, which have the potential to provide more detailed information about the scene. In particular, in the last decade, consumer-grade depth cameras have gained advantage over other sensors, given their low cost, portability, ease of use and measurement accuracy [8]. In brief, an RGB-D camera comprises two parts coupled together to give a dense matrix of pixel values; (a) an RGB camera for providing color information and (b) a depth camera for providing depth information [9]. Consequently, every pixel constructing the image is composed of color and distance values between a view-point and a certain point in the image (RGB-D values).

1.2. Use of RGB-D Cameras and Related Research in Agriculture

This type of camera has been applied in a number of areas of interest, such as indoor [10,11,12] and outdoor mapping [13], 3D reconstruction [14,15], motion and gesture recognition [16,17,18], and object detection [19]. Moreover, there has been an extensive use in robotics field and more specifically in navigation [19] and localization [2].
In recent years, stereoscopic vision depth cameras have been widely used in 3D reconstruction of objects and 3D mapping related to indoor environments [12,20]. Indicatively, the ZED stereo camera (Stereolabs Inc., San Francisco, CA, USA) has been employed in various indoor scenarios, namely volume designation of simple cubic and cylindrical objects through image segmentation process [21], crack detection and analysis on concrete surfaces using 3D data [22], terrestrial photogrammetry through an aerial mapping system [23], as well as the creation of indoor 3D mapping targeting to be used in studies for “smart” cities [24].
A plethora of researchers have studied the use of depth cameras in agricultural applications and identified their advantages and disadvantages in outdoor sceneries. An evaluation of five different depth cameras of three dissimilar technologies in agricultural applications was made by Condotta et al. [25]. According to their results, all cameras provided effective depth data indoors. Nonetheless, in outdoor environments the cameras using structured light and time-of-flight technology proved to be problematic, due to distortions by the intense lighting conditions. In particular, the aforementioned lighting may cause low contrast in the infrared image and lead to gaps in the corresponding depth image [25]. In outdoors applications, the most reliable data were provided by cameras using stereoscopy. Moreover, depth cameras were applied in agricultural applications for weed detection and above ground biomass volume estimation through 3D point clouds reconstruction [26]. In addition, efficient results in extraction of geometric structural parameters of vegetation with depth measurements were determined [27,28]. An effective approach of measuring the canopy structure on small plant populations in field conditions was presented in [29]. Furthermore, Jiang et al. [30] developed an approach to automatically quantify cotton canopy size in field conditions and showed the potential of using multidimensional traits as yield predictors. Additionally, an experiment using four different depth sensors in agricultural tasks was conducted by Vit and Shani [31], who estimated the quality of depth measurements for geometrical size estimation of agricultural objects with deep learning techniques. In tree crops, size estimation of mango fruits on trees in outdoor environment was made by Wang et al. [32].
Some of the RGB-D cameras are joined or can be combined with other sensors that allow for position and orientation of the camera to be recorded. Such sensors are, for example, inertial measurement units (IMUs) or global positioning system (GPS) sensors that provide positioning, velocity, and time information. As a result, depth cameras can be used to collect geometrical information about the environment and provide them as an input for robot localization and navigation. These added features in depth cameras are very useful for autonomous applications in agriculture or for capturing information about plants’ phenotype and growth. Studies have also been performed on the use of RGB-D cameras along with robotic systems to capture not only color information, but also spatial information about the environment. In addition, in [33] a solution was presented for autonomous obstacle avoidance performance of a UAV by using a deep learning-based object detection method and image processing with a depth camera. Another research, using depth camera mounted on an operational vehicle in an agricultural field, was presented in [34] for the reconstruction of the grapevines’ canopy to measure its volume as well as detect and count the grapevine bunches. Finally, Sa et al. [35] presented an accurate 3D detection method for sweet peppers peduncles in a farm field by using a depth camera on a robotic arm and a supervised machine learning approach.

1.3. 3D Mapping Procedures

With 3D mapping, the integration of appearance and shape information from depth sensors can be accomplished [36]. Some of the most commonly used tools for 3D mapping are the Octomap (University of Freiburg, Freiburg im Breisgau, Germany) [37] and real-time appearance-based mapping (RTABMap; Sherbrooke, QC, Canada). In particular, these tools are libraries related to the robot operating system (ROS).
The ROS software [38] for 3D mapping is widely used in robotic applications. More specifically, these tools can simultaneously capture and extract in a 3D map the environment area that a sensor is scanning, with the ability of representing it on a visualization tool. Octomap could be described as a probabilistic tool for 3D mapping, which is based on Octrees. An Octree is an information storing technique in a tree structure, in which there are nodes that each of them has eight “children”. The connection of all these nodes merges all the scanned data and generates continuous 3D maps. Apart from that, Octomap 3D mapping tool is a process which can efficiently recognize changes in the environment dynamically [39]. More specifically, the produced virtual environment with Octomap is composed of less noise from objects and robot position failures. Octomap meets four basic requirements. Firstly, free and occupied space, as it creates full 3D modeling and, secondly, it is updatable. Consequently, it is flexible, as the map can be expanded dynamically, while it is compact, as the produced map can be stored in memory and disk. It is worth mentioning that as compared with other 3D mapping tools, Octomap presents low computational load and memory usage. However, Octomap produces maps with only the depth data, which means that the points have only position information (x, y, z) and not color information (RGB).
Opposing Octomap, RTABMap creates 3D maps of the scanned environment with both color and depth data (RGB-D). A notable advantage of this 3D mapping tool is the fact that it provides a complete representation of the environment using the simultaneous localization and mapping (SLAM) algorithm. However, a main disadvantage of RTABMap is that it may lead to noisy maps, as it is unable to recognize dynamic objects [39]. In conclusion, these 3D maps can be stored for further processing and visualized in the ROS visualization tool (Rviz).

1.4. 3D Mapping Using Aerial-Based Systems

With the recent technological developments in the agricultural sector and the rise of digital agriculture and artificial intelligence, the use of unmanned aerial systems (UAS) is gaining popularity. This is mainly due to the fact that dedicated systems for commercial use have been made available to public [40]. Moreover, in contrast with satellite imagery, images acquired by UAS tend to demonstrate higher resolutions in both temporal (e.g., daily collections) and spatial (e.g., centimeters) level, while being insusceptible to cloud cover, thus, rendering them suitable for precision agriculture applications [41]. Furthermore, there is a high level of automatization in the analysis of the acquired images providing a range of products, such as orthomosaics with high spatial accuracy and 3D point clouds from the surveyed areas. An indicative recent study of using UAVs for agricultural applications is that of Christiansen et al. [42], where data collected from a LiDAR sensor mounted on a UAV were fused with global navigation satellite system (GNSS) and IMU data to carry out winter wheat field mapping for point clouds. Additionally, Anagnostis et al. [40] used UAS-derived images and deep learning to identify and segment tree canopies of orchards under diverse conditions. In addition, Gašparović et al. [43] combined classification algorithms with UAV images to map weeds in oat fields. Remarkably, RGB images from UAVs in conjunction with convolutional neural networks (CNNs) are constantly gaining ground [44,45,46], as highlighted in the recent literature review of Benos et al. [3].

1.5. Aim of the Present Study

All the above methods presented have certain drawbacks or do not consider RGB-D cameras. The aim of the present study was to investigate the use of RGB-D camera and UGV platform to autonomously map the environment of commercial orchards, map the location of trees and provide assessments of the tree size in terms of height and canopy volume by exporting and analyzing 3D point clouds. The results from the ground-based mapping system were compared with 3D orthomosaics acquired via an UAS. Finally, the fusion of the two datasets was performed as a means of reaching to a more accurate representation.

2. Materials and Methods

A ZED 2 depth camera, consisting of a stereo 2K camera with two color sensors (RGB) was used for the 3D reconstruction of orchard trees. The specific sensor has a horizontal field of view of 110° and can stream at a rate from 15 to 100 FPS, depending on the resolution. The camera’s connectivity is compatible to Universal Serial Bus (USB) 2.0. The baseline of 12 cm (distance between the left and right RGB sensor) manages a range of depth perception between 0.2 and 20 m. The most important characteristics of the ZED camera are summarized in Table 1.
The ZED 2 camera was connected to a NVIDIA Jetson TX2 development kit (NVIDIA Corporation, CA, U.S.A.), with Ubuntu GNU/Linux 18.04 (Canonical Ltd., London, UK) operating system. In this system, the ROS melodic distro was installed to access ROS tools, supporting the ZED 2 camera features. The Jetson TX2 processor was consisted of 8 GB of RAM, 32 GB Flash Storage, 2 Denver 64-bit CPUs, and Quad-Core A57 Complex. For the maximum speed and robustness of the system ensuring the best possible results, all GPU cores were set in full performance. The 3D reconstruction of trees was performed using the spatial mapping module of Stereolabs Software Development Kit (SDK) tool and RTABMap package of ROS. The SDK tool provides drivers for the camera, and several sample functions in Python programming language that were used for the measurements.
Due to the camera’s technology basic advantage of providing efficient results also in sunlight environments, this sensor is considered as an ideal solution for a robotic system operating outdoors. Moreover, the small size and compact structure of the camera makes it quite helpful to be used along with a robotic platform for applications such as mapping, object detection, etc. The sensing system was mounted on a Thorvald (SAGA Robotics SA, Oslo, Norway), which is an autonomous all terrain UGV (Figure 1) [47].
The Thorvald robotic vehicle was also equipped with a high accuracy GPS (RTK) as a means of providing the position of the robot and sequentially the position of the camera providing the ability to georeference the point cloud produced by scanning the orchard. Moreover, the scanning system was powered by the Thorvald’s battery. The setup was navigated in the field, capturing RGB-D images, collecting the necessary data to construct the 3D point cloud of the orchard.
The camera was located on a tripod attached on the Thorvald vehicle at about 1.5 m above the ground level facing sideways towards the trees canopy in horizontal position. In addition, the ZED camera was oriented towards the direction of the tree of interest, and it was manually adjusted as for the viewing angle and the height according to each tree. This adjustment was necessary due to variations in geometry characteristics of the canopy, volume and height of every individual tree.
The RGB-D-based scanning system setup was used in real field conditions to scan and construct the 3D representation of a commercial walnut orchard, located in Thessaly region, in Greece. The field measurements were conducted on sample trees of different height, volume and shape, on a sunny day during September 2020. The robot-camera system was used for in-field navigation, capturing RGB and depth data by steering a circle around each tree, at a distance of 2 m from the canopy, for about one minute. According to the acquisition rate, this procedure produced 3500 frames per sample tree. The camera readings were acquired at a high frame rate, namely 50–60 frames per second, providing sufficient overlapping among the frames for better 3D reconstruction of the model, as the SDK tool (Stereolabs) used for the 3D point cloud generation, merges the additional points of the scene and creates a more complete point cloud. The overlapped areas allow for 3D model construction by estimating the relative position of the camera for each frame. Several parameters of the sensor were adjusted through the SDK tool, such as brightness, saturation and contrast. Furthermore, according to the camera’s application programming interface (API) documentation, several parameters were set to fit in the field conditions. Specifically, the resolution of the camera was set to 1280 × 720 pixels (720p), and the point cloud mapping resolution was set to 2 cm. Additionally, the depth data range was set between 0.4- and 5-m distance from the camera position to create point cloud with high dense geometry and high resolution. Every point cloud of each tree was stored for further processing and saved in an object (OBJ) or polygon (PLY) file format, which is compatible with various point cloud and image processing software, such as Meshlab [48] and CloudCompare [49].
The ROS framework was utilized by the robotic platform to navigate in the field, while supporting data acquisition through the integrated “rosbag” tool. The system was recording simultaneously the RGB-D data from the ZED camera and the accurate position of the robotic vehicle utilizing the RTK-GNSS. The ZED camera uses its internal IMU to set the location and direction of the camera in relative coordinates. Therefore, it provides the RGB-D information in relative geodetic system. Combining the two datasets, the relative coordinates are referenced to the global coordinate system (GPS) “translated” into UTM coordinates (Figure 2). The “ros tf” library was utilized for this task.
The fusion of the two coordinate systems provided the ability to accurately georeference the spatial data captured by the camera which, after processing, produced the georeferenced 3D point cloud of the orchard corresponding to reality.
After the point cloud extraction, the height and volume of each tree was computed using CloudCompare and its internal tools. During this process, the point cloud is generalized to a surface elevation model and consequently the volume is calculated on the basis of the difference between a fixed ground elevation and the surface model. For the given case, the ground level was set as the lowest point for each tree point cloud. In other words, this technique is similar to draping fabric over the tree and computing the volume under the fabric. The resolution for the volume measurement was set equal to 2 cm. Furthermore, the density of points was calculated. The workflow of the data analysis followed in the study is briefly presented in Figure 3.
In addition to the ground-based scanning system, the orchard’s structure was also mapped from above using a UAV. The flight occurred during the same period with the ground-based measurements to ensure the comparability between the two-point cloud producing methods. The UAV was a quadcopter (Phantom 4, DJI Technology Co., Ltd., Shenzhen, China) equipped with high accuracy GNSS (real-time kinematic—RTK) and high-resolution RGB camera (5472 × 3648 resolution, at a 3:2 aspect ratio). The use of RTK GNSS was necessary in order to accurately geotag the acquired aerial images, while the flight plans were parametrized accordingly (UAV flight height, speed, number of captured images, side overlap, and forward overlap ratio) to produce high accuracy, below centimeter pixel size, orthomosaics. The produced orthomosaic can accurately provide the top view of the tree canopies in 2 dimensions and, thus, it was utilized as the ground truth for measuring the canopies’ surface. The 2D point cloud acquired by the ZED camera was compared with the orthomosaic.
For the purpose of comparing the measurements derived from the ground-based systems against those of aerial-based systems, simple linear regression analysis was utilized taking also into account the 95% confidence interval.

3. Results and Discussion

In order to estimate the true position of an object (a tree within the orchard in this case), the first step was to create a 3D model of the object in relative coordinates with the position of the camera as the axis origin and then set it in real-world coordinates by aligning this model to a known point (based on the camera position). This georeferenced point cloud aimed to be compared with a 3D point cloud produced from a UAV. Moreover, the georeferenced point cloud was imported in quantum geographic information system (Q GIS) to check the converted point cloud with a 2D georeferenced raster image of the same area. Reprojecting the point cloud in a real-world coordinate system provided the possibility to be used in various future simulation agricultural applications and robot tasks, such as object detection, spraying, or harvesting [50].
The representation of the orchard in two dimensions provided a general idea of the top view of the trees within the orchard, hence, providing the ability to estimate the canopy surface. This information can be valuable for estimating the age and the yield potential of each tree. In our study, the 2D representation also served as the first stage for the comparison of the two data acquisition methods. In Figure 4, the top view of the georeferenced point cloud acquired by the ground-based measuring system is projected overlayed on the detailed georeferenced orthomosaic constructed from the UAV-derived aerial images. The orchard, at the time of measuring, consisted of trees of different canopy size, color, and stage (fully developed, partly defoliated, or defoliated). Despite of the heterogeneity of the trees within the orchard, the results from the two methods were similar. This was also confirmed by the results of the regression between the two (Figure 5).
For the representation of the collected data in the three-dimensional world, the 3D point clouds were produced and converted to digital asset exchange (DAE) format, as to estimate the tree dimensional parameters, namely the height and canopy volume. Given that the datasets were georeferenced using high accuracy GNSS, the height of the captured trees could be accurately calculated (Figure 6). Furthermore, the robot-camera setup presented accurate results of the volume measurements of the trees confirming that the RGB-D cameras can serve as useful tools for agricultural applications, such as fertilizing and spraying, being part of decision support tools for variable rate applications according to the characteristics of each tree.
It is worth mentioning that the ZED camera, with the setup and adjustments used in the study, could not accurately detect the end details of the trees, such as thin branches, individual leaves, or nuts, as it could not provide extremely dense point clouds that are required for such tasks. Increasing the acquisition rate and the camera resolution and scanning more than one circles around each tree would enrich the point clouds producing very detailed point clouds. However, this would not be practical in agricultural applications, since it would be time consuming and hardware requirements for proper data acquisition and processing would significantly increase. In our system setup, despite the limitations, the constructed point cloud provided a model of the trees within the orchard very close to reality. This result is in agreement with the conclusions presented in [51], where the use of low-cost 3D sensors provided reliable results for plant phenotyping and can be applied in automated procedures for agricultural applications.
Comparing the two capturing systems, the ZED camera provided a good representation of the trees, capturing details of the trunk, the lower, and mid canopy. Moreover, the center of the top canopy had some gaps due to the position and the viewing angle of the camera (Figure 6a). Conversely, the point cloud derived from the orthomosaic produced by the UAV aerial images provided a good representation of the top of the canopy, but had poor performance in the representation of the middle and lower canopy and the tree’s trunk (Figure 6b). This was expected, since by definition the UAVs can capture the top view of the objects, being unable to penetrate inside and under the canopy. However, some points of the lower canopy, the trunk, and the ground were captured making feasible the accurate estimation of the tree height, calculated by subtracting the ground surface elevation from the top of the canopy elevation. This fact led to similar height measurements from both measuring methods (Figure 7a).
From a practical point of view, a significant drawback of using the ZED camera ground-based system was the time needed to navigate within the orchard and capture the given number of trees. On the other hand, the aerial images derived from the UAV platform could be acquired within a short flight.
In terms of tree volume measurements, the results from both methods showed similar trend; however, the UAV-derived tree volume was constantly lower by about 7.4 m3 while the slope of the relationship was 1.26 (Figure 7b). This is attributed to the fact that the UAVs can capture the upper part of the canopy, thus missing a significant part of the tree volume in the mid and lower canopy as seen in Figure 8b. However, these parts were captured in detail by the ZED camera. The latter managed to capture in detail almost the whole canopy, missing only a part of the middle top. As a consequence, the fusion of the two point clouds into a unified one constructed a more complete 3D model (Figure 8c and Figure 9).
The constructed point clouds can provide a useful input, by consequently converting them to meshes and importing in Gazebo simulation environment. The resulted virtual orchard environment may be used for testing of the robot navigation and localization. This testing will be carried out for estimation of the robot performance, in tasks such as autonomous navigation and obstacle avoidance before being evaluated in real field conditions. The visualization model in the Gazebo simulation environment can provide an adequate representation of the real orchard field and the possibility to make quality tests in a virtual world. In robotic applications, basic stage of the whole implementation is the algorithm testing part, which is performed in a virtual world before established in the real world. The use of simulation environments in various tasks and different environments, as to evaluate the robots’ performance, could be a quite costly and time effective procedure during the stage of testing and development of an application. As a result, using simulation environments in robotic applications, could optimize the robot behavior before the actual tests in the field [52].

4. Conclusions

In this study, the use of RGB-D camera to map the environment of commercial orchards was assessed and compared with 3D orthomosaics acquired using an UAS. The study verified that depth cameras, using stereoscopic vision to calculate the depth values, can provide accurate results in outdoor environments. The system, indeed, showed promising results, as it was capable to work under direct sunlight conditions capturing a high number of points with efficient resolution.
The produced point clouds provided efficient results for the structural parameters of the trees, as their shape and volume were adequately described. In some sample trees, lack of information of the inside and top of the tree canopy was observed. This limitation of the system was due to the initial settings of the camera’s parameters and/or due to the finite number of frames captured from each tree, set to the maximum of the hardware’s capabilities. Changes in these parameters or increasing of the image frames could possibly improve the 3D model reconstruction, though increasing significantly the processing time, hardware requirements, and, consequently, storage. Furthermore, scanning each tree more than once would significantly increase the point clouds’ density and accuracy, but this would affect the time required for the in-field scanning.
Overall, the UAV point cloud provided an accurate representation of the top view of the tree canopies. The orthomosaic, acquired by the RTK GNSS enabled UAS, was utilized as the ground truth for the 2D representation of the surface of the top view of the tree canopies. The 2D point cloud acquired by the ZED camera was successfully compared with the orthomosaic proving that the latter sensor can be an alternative providing accurate results. On the other hand, the point cloud from the ZED camera captured in much detail the structural characteristics of the trees all around, but had lack of information of the top canopy structure. Fusion of the two datasets led to construction of a more complete 3D model with increased accuracy providing a better representation of the tree structure. Focusing on the cost, aerial imaging is affordable, easier to operate and can cover larger areas as compared to on-ground systems. The RGB-D system on the other hand, may be facilitated with conventional agricultural machinery, capturing data while performing in-field operations, thus, minimizing the operational costs. Nevertheless, this study seeks to pave the ground to future applications following the trends of smart-autonomous farming leading towards Agriculture 4.0.
Finally, the 3D point clouds can be imported in Gazebo simulation environment to provide the virtual environment of the orchard to be used for efficient programming evaluation and demonstration of the robotic platform’s behavior and interaction in the orchard. Future developments include the automatization of the analysis procedure to provide the results in real time as the system navigates in the orchard. This will enhance situation awareness for safe and undisturbed navigation of the robotic platform in complex environments for the sake of avoiding possible injuries or damages [53]. In a broader perspective, further research is required towards improving the speed and accuracy of the existing cameras and image processing systems as well as decreasing the overall complexity [7,54,55,56]. Furthermore, fusion of data acquired by a group of unmanned vehicles could allow for better accuracy in a timely manner.

Author Contributions

Conceptualization, A.C.T. and D.B.; methodology, E.F., D.K. and P.B.; software, E.F. and D.K.; validation, A.C.T., L.B. and P.B.; writing-original draft preparation, E.F., L.B. and A.C.T.; writing-review and editing, L.B., A.C.T., P.B. and D.B.; visualization, E.F., A.C.T. and L.B.; supervision, A.C.T. and D.B.; project administration, D.B. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Han, J.; Shao, L.; Xu, D.; Shotton, J. Enhanced Computer Vision with Microsoft Kinect Sensor: A Review. IEEE Trans. Cybern. 2013, 43, 1318–1334. [Google Scholar] [CrossRef] [PubMed]
  2. Ganganath, N.; Leung, H. Mobile robot localization using odometry and kinect sensor. In Proceedings of the 2012 IEEE International Conference on Emerging Signal Processing Applications, Las Vegas, NV, USA, 12–14 January 2012; pp. 91–94. [Google Scholar]
  3. Benos, L.; Tagarakis, A.C.; Dolias, G.; Berruto, R.; Kateris, D.; Bochtis, D. Machine Learning in Agriculture: A Comprehensive Updated Review. Sensors 2021, 21, 3758. [Google Scholar] [CrossRef] [PubMed]
  4. Lindner, L.; Sergiyenko, O.; Rivas-López, M.; Ivanov, M.; Rodríguez-Quiñonez, J.C.; Hernández-Balbuena, D.; Flores-Fuentes, W.; Tyrsa, V.; Muerrieta-Rico, F.N.; Mercorelli, P. Machine vision system errors for unmanned aerial vehicle navigation. In Proceedings of the 2017 IEEE 26th International Symposium on Industrial Electronics (ISIE), Edinburgh, UK, 19–21 June 2017; pp. 1615–1620. [Google Scholar]
  5. Zhao, Y.; Gong, L.; Huang, Y.; Liu, C. A review of key techniques of vision-based control for harvesting robot. Comput. Electron. Agric. 2016, 127, 311–323. [Google Scholar] [CrossRef]
  6. Fu, L.; Tola, E.; Al-Mallahi, A.; Li, R.; Cui, Y. A novel image processing algorithm to separate linearly clustered kiwifruits. Biosyst. Eng. 2019, 183, 184–195. [Google Scholar] [CrossRef]
  7. Fu, L.; Gao, F.; Wu, J.; Li, R.; Karkee, M.; Zhang, Q. Application of consumer RGB-D cameras for fruit detection and localization in field: A critical review. Comput. Electron. Agric. 2020, 177, 105687. [Google Scholar] [CrossRef]
  8. Khoshelham, K.; Elberink, S.O. Accuracy and Resolution of Kinect Depth Data for Indoor Mapping Applications. Sensors 2012, 12, 1437–1454. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  9. Liu, H.; Qu, D.; Xu, F.; Zou, F.; Song, J.; Jia, K. Approach for accurate calibration of RGB-D cameras using spheres. Opt. Express 2020, 28, 19058–19073. [Google Scholar] [CrossRef]
  10. Menna, F.; Remondino, F.; Battisti, R.; Nocerino, E. Geometric investigation of a gaming active device. In Proceedings of the Videometrics, Range Imaging, and Applications XI; Remondino, F., Shortis, M.R., Eds.; SPIE: Bellingham, WA, USA, 2011; Volume 8085, pp. 173–187. [Google Scholar]
  11. Henry, P.; Krainin, M.; Herbst, E.; Ren, X.; Fox, D. RGB-D Mapping: Using Depth Cameras for Dense 3D Modeling of Indoor Environments BT—Experimental Robotics. In Proceedings of the 12th International Symposium on Experimental Robotics, New Delhi and Agra, India, 18–21 December 2010; Khatib, O., Kumar, V., Sukhatme, G., Eds.; Springer: Berlin/Heidelberg, Germany, 2014; pp. 477–491. [Google Scholar]
  12. Endres, F.; Hess, J.; Sturm, J.; Cremers, D.; Burgard, W. 3-D Mapping with an RGB-D camera. IEEE Trans. Robot. 2014, 30, 177–187. [Google Scholar] [CrossRef]
  13. Butkiewicz, T. Low-cost coastal mapping using Kinect v2 time-of-flight cameras. In Proceedings of the 2014 Oceans—St. John’s, St. John’s, NL, Canada, 14–19 September 2014; pp. 1–9. [Google Scholar]
  14. Pan, H.; Guan, T.; Luo, Y.; Duan, L.; Tian, Y.; Yi, L.; Zhao, Y.; Yu, J. Dense 3D reconstruction combining depth and RGB information. Neurocomputing 2016, 175, 644–651. [Google Scholar] [CrossRef]
  15. Herbst, E.; Henry, P.; Ren, X.; Fox, D. Toward object discovery and modeling via 3-D scene comparison. In Proceedings of the 2011 IEEE International Conference on Robotics and Automation, Shanghai, China, 9–13 May 2011; pp. 2623–2629. [Google Scholar]
  16. Wang, K.; Zhang, G.; Bao, H. Robust 3D Reconstruction with an RGB-D Camera. IEEE Trans. Image Process. 2014, 23, 4893–4906. [Google Scholar] [CrossRef] [Green Version]
  17. Benos, L.; Bechar, A.; Bochtis, D. Safety and ergonomics in human-robot interactive agricultural operations. Biosyst. Eng. 2020, 200, 55–72. [Google Scholar] [CrossRef]
  18. Benos, L.; Tsaopoulos, D.; Bochtis, D. A Review on Ergonomics in Agriculture. Part II: Mechanized Operations. Appl. Sci. 2020, 10, 3484. [Google Scholar] [CrossRef]
  19. Hernández-López, J.-J.; Quintanilla-Olvera, A.-L.; López-Ramírez, J.-L.; Rangel-Butanda, F.-J.; Ibarra-Manzano, M.-A.; Almanza-Ojeda, D.-L. Detecting objects using color and depth segmentation with Kinect sensor. Procedia Technol. 2012, 3, 196–204. [Google Scholar] [CrossRef] [Green Version]
  20. Marin, G.; Agresti, G.; Minto, L.; Zanuttigh, P. A multi-camera dataset for depth estimation in an indoor scenario. Data Br. 2019, 27, 104619. [Google Scholar] [CrossRef]
  21. Tran, T.M.; Ta, K.D.; Hoang, M.; Nguyen, T.V.; Nguyen, N.D.; Pham, G.N. A study on determination of simple objects volume using ZED stereo camera based on 3D-points and segmentation images. Int. J. Emerg. Trends Eng. Res. 2020, 8, 1990–1995. [Google Scholar] [CrossRef]
  22. Sarker, M.M.; Ali, T.A.; Abdelfatah, A.; Yehia, S.; Elaksher, A. A cost-effective method for crack detection and measurement on concrete surface. ISPRS-Int. Arch. Photogramm. Remote Sens. Spat. Inf. Sci. 2017, 42, 237–241. [Google Scholar] [CrossRef] [Green Version]
  23. Burdziakowski, P. Low cost real time UAV stereo photogrammetry modelling technique-accuracy considerations. In Proceedings of the E3S Web of Conferences; EDP Sciences: Les Ulis, France, 2018; Volume 63, p. 00020. [Google Scholar]
  24. Gupta, T.; Li, H. Indoor mapping for Smart Cities—An affordable approach: Using kinect sensor and ZED stereo camera. In Proceedings of the 2017 International Conference on Indoor Positioning and Indoor Navigation, IPIN 2017, Sapporo, Japan, 18–21 September 2017; Institute of Electrical and Electronics Engineers Inc.: New York, NY, USA, 2017; Volume 2017, pp. 1–8. [Google Scholar]
  25. Condotta, I.C.F.S.; Brown-Brandl, T.M.; Pitla, S.K.; Stinn, J.P.; Silva-Miranda, K.O. Evaluation of low-cost depth cameras for agricultural applications. Comput. Electron. Agric. 2020, 173, 105394. [Google Scholar] [CrossRef]
  26. Andújar, D.; Dorado, J.; Fernández-Quintanilla, C.; Ribeiro, A. An Approach to the Use of Depth Cameras for Weed Volume Estimation. Sensors 2016, 16, 972. [Google Scholar] [CrossRef] [Green Version]
  27. Azzari, G.; Goulden, M.L.; Rusu, R.B. Rapid Characterization of Vegetation Structure with a Microsoft Kinect Sensor. Sensors 2013, 13, 2384–2398. [Google Scholar] [CrossRef] [Green Version]
  28. Andújar, D.; Ribeiro, A.; Fernández-Quintanilla, C.; Dorado, J. Using depth cameras to extract structural parameters to assess the growth state and yield of cauliflower crops. Comput. Electron. Agric. 2016, 122, 67–73. [Google Scholar] [CrossRef]
  29. Hui, F.; Zhu, J.; Hu, P.; Meng, L.; Zhu, B.; Guo, Y.; Li, B.; Ma, Y. Image-based dynamic quantification and high-accuracy 3D evaluation of canopy structure of plant populations. Ann. Bot. 2018, 121, 1079–1088. [Google Scholar] [CrossRef] [PubMed]
  30. Jiang, Y.; Li, C.; Paterson, A.H.; Sun, S.; Xu, R.; Robertson, J. Quantitative Analysis of Cotton Canopy Size in Field Conditions Using a Consumer-Grade RGB-D Camera. Front. Plant. Sci. 2018, 8, 2233. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  31. Vit, A.; Shani, G. Comparing RGB-D Sensors for Close Range Outdoor Agricultural Phenotyping. Sensors 2018, 18, 4413. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  32. Wang, Z.; Walsh, K.B.; Verma, B. On-Tree Mango Fruit Size Estimation Using RGB-D Images. Sensors 2017, 17, 2738. [Google Scholar] [CrossRef] [Green Version]
  33. Wang, D.; Li, W.; Liu, X.; Li, N.; Zhang, C. UAV environmental perception and autonomous obstacle avoidance: A deep learning and depth camera combined solution. Comput. Electron. Agric. 2020, 175, 105523. [Google Scholar] [CrossRef]
  34. Milella, A.; Marani, R.; Petitti, A.; Reina, G. In-field high throughput grapevine phenotyping with a consumer-grade depth camera. Comput. Electron. Agric. 2019, 156, 293–306. [Google Scholar] [CrossRef]
  35. Sa, I.; Lehnert, C.; English, A.; McCool, C.; Dayoub, F.; Upcroft, B.; Perez, T. Peduncle Detection of Sweet Pepper for Autonomous Crop Harvesting—Combined Color and 3-D Information. IEEE Robot. Autom. Lett. 2017, 2, 765–772. [Google Scholar] [CrossRef] [Green Version]
  36. Konolige, K. Projected texture stereo. In Proceedings of the 2010 IEEE International Conference on Robotics and Automation, Anchorage, AK, USA, 3–7 May 2010; pp. 148–155. [Google Scholar]
  37. Hornung, A.; Wurm, K.M.; Bennewitz, M.; Stachniss, C.; Burgard, W. OctoMap: An efficient probabilistic 3D mapping framework based on octrees. Auton. Robot. 2013, 34, 189–206. [Google Scholar] [CrossRef] [Green Version]
  38. ROS—Robot Operating System. Available online: https://www.ros.org/ (accessed on 13 December 2021).
  39. De Silva, K.T.D.S.; Cooray, B.P.A.; Chinthaka, J.I.; Kumara, P.P.; Sooriyaarachchi, S.J. Comparative Analysis of Octomap and RTABMap for Multi-Robot Disaster Site Mapping; Institute of Electrical and Electronics Engineers (IEEE): New York, NY, USA, 2019; pp. 433–438. [Google Scholar]
  40. Anagnostis, A.; Tagarakis, A.C.; Kateris, D.; Moysiadis, V.; Sørensen, C.G.; Pearson, S.; Bochtis, D. Orchard Mapping with Deep Learning Semantic Segmentation. Sensors 2021, 21, 3813. [Google Scholar] [CrossRef]
  41. Zhang, C.; Kovacs, J.M. The application of small unmanned aerial systems for precision agriculture: A review. Precis. Agric. 2012, 13, 693–712. [Google Scholar] [CrossRef]
  42. Christiansen, M.; Laursen, M.; Jørgensen, R.; Skovsen, S.; Gislum, R. Designing and Testing a UAV Mapping System for Agricultural Field Surveying. Sensors 2017, 17, 2703. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  43. Gašparović, M.; Zrinjski, M.; Barković, Đ.; Radočaj, D. An automatic method for weed mapping in oat fields based on UAV imagery. Comput. Electron. Agric. 2020, 173, 105385. [Google Scholar] [CrossRef]
  44. Veeranampalayam Sivakumar, A.N.; Li, J.; Scott, S.; Psota, E.; JJhala, A.; Luck, J.D.; Shi, Y. Comparison of Object Detection and Patch-Based Classification Deep Learning Models on Mid- to Late-Season Weed Detection in UAV Imagery. Remote Sens. 2020, 12, 2136. [Google Scholar] [CrossRef]
  45. Kerkech, M.; Hafiane, A.; Canals, R. Vine disease detection in UAV multispectral images using optimized image registration and deep learning segmentation approach. Comput. Electron. Agric. 2020, 174, 105446. [Google Scholar] [CrossRef]
  46. Barrero, O.; Perdomo, S.A. RGB and multispectral UAV image fusion for Gramineae weed detection in rice fields. Precis. Agric. 2018, 19, 809–822. [Google Scholar] [CrossRef]
  47. Grimstad, L.; From, P.J. The Thorvald II Agricultural Robotic System. Robotics 2017, 6, 24. [Google Scholar] [CrossRef] [Green Version]
  48. MeshLab. Available online: https://www.meshlab.net/ (accessed on 17 November 2020).
  49. CloudCompare. Available online: http://www.cloudcompare.org/ (accessed on 17 November 2020).
  50. Moysiadis, V.; Tsolakis, N.; Katikaridis, D.; Sørensen, C.G.; Pearson, S.; Bochtis, D. Mobile Robotics in Agricultural Operations: A Narrative Review on Planning Aspects. Appl. Sci. 2020, 10, 3453. [Google Scholar] [CrossRef]
  51. Paulus, S.; Behmann, J.; Mahlein, A.-K.; Plümer, L.; Kuhlmann, H. Low-Cost 3D Systems: Suitable Tools for Plant Phenotyping. Sensors 2014, 14, 3001–3018. [Google Scholar] [CrossRef] [Green Version]
  52. Guzman, R.; Navarro, R.; Beneto, M.; Carbonell, D. Robotnik—Professional service robotics applications with ROS. Stud. Comput. Intell. 2016, 625, 253–288. [Google Scholar] [CrossRef]
  53. Benos, L.; Kokkotis, C.; Tsatalas, T.; Karampina, E.; Tsaopoulos, D.; Bochtis, D. Biomechanical Effects on Lower Extremities in Human-Robot Collaborative Agricultural Tasks. Appl. Sci. 2021, 11, 11742. [Google Scholar] [CrossRef]
  54. Rodríguez-Quiñonez, J.C.; Sergiyenko, O.; Flores-Fuentes, W.; Rivas-lopez, M.; Hernandez-Balbuena, D.; Rascón, R.; Mercorelli, P. Improve a 3D distance measurement accuracy in stereo vision systems using optimization methods’ approach. Opto-Electron. Rev. 2017, 25, 24–32. [Google Scholar] [CrossRef]
  55. Lindner, L.; Sergiyenko, O.; Rodríguez-Quiñonez, J.C.; Tyrsa, V.; Mercorelli, P.; Fuentes, W.F.; Murrieta-Rico, F.N.; Nieto-Hipolito, J.I. Continuous 3D scanning mode using servomotors instead of stepping motors in dynamic laser triangulation. In Proceedings of the 2015 IEEE 24th International Symposium on Industrial Electronics (ISIE), Buzios, Brazil, 3–5 June 2015; pp. 944–949. [Google Scholar]
  56. Rueda-Ayala, V.P.; Peña, J.M.; Höglind, M.; Bengochea-Guevara, J.M.; Andújar, D. Comparing UAV-Based Technologies and RGB-D Reconstruction Methods for Plant Height and Biomass Monitoring on Grass Ley. Sensors 2019, 19, 535. [Google Scholar] [CrossRef] [PubMed] [Green Version]
Sensors 22 01571 g001 550
Figure 1. Setup of the ground-based scanning system mounted on Thorvald unmanned ground vehicle.
Figure 1. Setup of the ground-based scanning system mounted on Thorvald unmanned ground vehicle.
Sensors 22 01571 g001
Sensors 22 01571 g002 550
Figure 2. Location and orientation of the RGB-D camera in the relative coordinate system using the IMU (a) and georeferencing of the vehicle and the RGB-D to UTM coordinate system (b).
Figure 2. Location and orientation of the RGB-D camera in the relative coordinate system using the IMU (a) and georeferencing of the vehicle and the RGB-D to UTM coordinate system (b).
Sensors 22 01571 g002
Sensors 22 01571 g003 550
Figure 3. Flow chart of the procedure for the 3D point cloud construction using data from ZED 2 camera and its comparison with the UAV derived point cloud.
Figure 3. Flow chart of the procedure for the 3D point cloud construction using data from ZED 2 camera and its comparison with the UAV derived point cloud.
Sensors 22 01571 g003
Sensors 22 01571 g004 550
Figure 4. The projection of the point cloud (top view) of the orchard in 2D, mapped with the two methods used in the study; the ground-based system using depth camera mounted on Thorvald UGV and the orthomosaic exported from aerial images acquired using UAV.
Figure 4. The projection of the point cloud (top view) of the orchard in 2D, mapped with the two methods used in the study; the ground-based system using depth camera mounted on Thorvald UGV and the orthomosaic exported from aerial images acquired using UAV.
Sensors 22 01571 g004
Sensors 22 01571 g005 550
Figure 5. Comparison between the canopy size estimated by the ground-based and the aerial-based systems used in the study; the colored area shows the lower and upper confidence (95%) limits.
Figure 5. Comparison between the canopy size estimated by the ground-based and the aerial-based systems used in the study; the colored area shows the lower and upper confidence (95%) limits.
Sensors 22 01571 g005
Sensors 22 01571 g006 550
Figure 6. The side view of the georeferenced 3D point cloud of a sample tree captured by the ground-based system using the ZED camera (a) and by the UAV aerial-based system (b), used to estimate the tree height.
Figure 6. The side view of the georeferenced 3D point cloud of a sample tree captured by the ground-based system using the ZED camera (a) and by the UAV aerial-based system (b), used to estimate the tree height.
Sensors 22 01571 g006
Sensors 22 01571 g007 550
Figure 7. Comparison between the trees dimension measurements; trees height (a) and trees volume (b), derived by using the two sensing methods; the UAV aerial-based system and the UGV-ZED depth camera ground-based system; the colored areas show the lower and upper confidence (95%) limits.
Figure 7. Comparison between the trees dimension measurements; trees height (a) and trees volume (b), derived by using the two sensing methods; the UAV aerial-based system and the UGV-ZED depth camera ground-based system; the colored areas show the lower and upper confidence (95%) limits.
Sensors 22 01571 g007
Sensors 22 01571 g008 550
Figure 8. Point clouds of a sample tree derived by the UGV-ZED depth camera ground-based system (a), the UAV based aerial system (b), and the fusion of the two point clouds (c).
Figure 8. Point clouds of a sample tree derived by the UGV-ZED depth camera ground-based system (a), the UAV based aerial system (b), and the fusion of the two point clouds (c).
Sensors 22 01571 g008
Sensors 22 01571 g009 550
Figure 9. The 3D projection of the point clouds exported with the two methods used in the study; the ground-based system using depth camera mounted on Thorvald UGV ((a), white dots) and the orthomosaic exported from aerial images acquired using UAV ((b), colored dots).
Figure 9. The 3D projection of the point clouds exported with the two methods used in the study; the ground-based system using depth camera mounted on Thorvald UGV ((a), white dots) and the orthomosaic exported from aerial images acquired using UAV ((b), colored dots).
Sensors 22 01571 g009
Table
Table 1. Main characteristics of ZED camera used in the study.
Table 1. Main characteristics of ZED camera used in the study.
SensorRGB
Lensf/1.8 aperture
Depth range0.2–20 m
Field of view (horizontal, vertical, diagonal)110° (H), 70° (V), 120° (D)
Single image and depth resolution (pixels) Resolution (pixels)Frame rate (Frames per second)
HD2K2208 × 124215 FPS
HD10801920 × 108030/15 FPS
HD7201280 × 72060/30/15 FPS
VGA672 × 376100/60/30/15 FPS
Complementary sensorsAccelerometer, Gyroscope, Barometer, Magnetometer, Temperature sensor
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Tagarakis, A.C.; Filippou, E.; Kalaitzidis, D.; Benos, L.; Busato, P.; Bochtis, D. Proposing UGV and UAV Systems for 3D Mapping of Orchard Environments. Sensors 2022, 22, 1571. https://doi.org/10.3390/s22041571

AMA Style

Tagarakis AC, Filippou E, Kalaitzidis D, Benos L, Busato P, Bochtis D. Proposing UGV and UAV Systems for 3D Mapping of Orchard Environments. Sensors. 2022; 22(4):1571. https://doi.org/10.3390/s22041571

Chicago/Turabian Style

Tagarakis, Aristotelis C., Evangelia Filippou, Damianos Kalaitzidis, Lefteris Benos, Patrizia Busato, and Dionysis Bochtis. 2022. "Proposing UGV and UAV Systems for 3D Mapping of Orchard Environments" Sensors 22, no. 4: 1571. https://doi.org/10.3390/s22041571

APA Style

Tagarakis, A. C., Filippou, E., Kalaitzidis, D., Benos, L., Busato, P., & Bochtis, D. (2022). Proposing UGV and UAV Systems for 3D Mapping of Orchard Environments. Sensors, 22(4), 1571. https://doi.org/10.3390/s22041571

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop