Next Article in Journal
Relationship of Carbohydrate Intake during a Single-Stage One-Day Ultra-Trail Race with Fatigue Outcomes and Gastrointestinal Problems: A Systematic Review
Next Article in Special Issue
Analysis of the LNAPL Migration Process in the Vadose Zone under Two Different Media Conditions
Previous Article in Journal
One-Year Lesson: Machine Learning Prediction of COVID-19 Positive Cases with Meteorological Data and Mobility Estimate in Japan
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Spatial Analysis of Groundwater Hydrochemistry through Integrated Multivariate Analysis: A Case Study in the Urbanized Langat Basin, Malaysia

by
Nur Fatihah Mohamad Zainol
1,
Azim Haziq Zainuddin
2,
Ley Juen Looi
1,
Ahmad Zaharin Aris
2,
Noorain Mohd Isa
1,*,
Anuar Sefie
3 and
Ku Mohd Kalkausar Ku Yusof
4
1
Department of Environment, Faculty of Forestry and Environment, Universiti Putra Malaysia, Serdang 43400 UPM, Malaysia
2
International Institute of Aquaculture and Aquatic Sciences, Universiti Putra Malaysia, Port Dickson 71050, Malaysia
3
National Water Research Institute of Malaysia, Lot 5377, Jalan Putra Permai, Seri Kembangan 43300, Malaysia
4
Department of Chemistry, Universiti Malaysia Terengganu, Kuala Terengganu 21300, Malaysia
*
Author to whom correspondence should be addressed.
Int. J. Environ. Res. Public Health 2021, 18(11), 5733; https://doi.org/10.3390/ijerph18115733
Submission received: 9 April 2021 / Revised: 16 May 2021 / Accepted: 20 May 2021 / Published: 27 May 2021
(This article belongs to the Special Issue Groundwater Contamination in Urbanized Areas)

Abstract

:
Rapid urbanization and industrial development in the Langat Basin has disturbed the groundwater quality. The populations’ reliance on groundwater sources may induce possible risks to human health such as cancer and endocrine dysfunction. This study aims to determine the groundwater quality of an urbanized basin through 24 studied hydrochemical parameters from 45 groundwater samples obtained from 15 different sampling stations by employing integrated multivariate analysis. The abundance of the major ions was in the following order: bicarbonate (HCO3) > chloride (Cl) > sodium (Na+) > sulphate (SO42−) > calcium (Ca2+) > potassium (K+) > magnesium (Mg2+). Heavy metal dominance was in the following order: Fe > Mn > Zn > As > Hg > Pb > Ni > Cu > Cd > Se > Sr. Classification of the groundwater facies indicated that the studied groundwater belongs to the Na-Cl with saline water type and Na-HCO3 with mix water type characteristics. The saline water type characteristics are derived from agricultural activities, while the mixed water types occur from water–rock interaction. Multivariate analysis performance suggests that industrial, agricultural, and weathering activities have contributed to groundwater contamination. The study will help in the understanding of the groundwater quality issue and serve as a reference for other basins with similar characteristics.

1. Introduction

Many parts of the world are experiencing a shortage of water supply; hence, groundwater acts as a substitute for the lack of available surface water. In most cases, groundwater possesses a valuable property in comparison to surface water. Half of the world’s total potable water is pumped from groundwater aquifers, with the highest dependency on groundwater consumption occurring in megacities [1].
Following the rapid pace of economic growth and coupled with pressures from an increasing population, development has inevitably encroached into groundwater areas. This encroachment is further exacerbated by the rising demands of the manufacturing industry, along with the usage of chemicals and the never-ending demand for food, both locally and globally, that has led to a tremendous increase in the application of fertilizers and pesticides [2]. In many developing countries, improper disposal of wastewater coming from municipal, industrial, and agricultural sources with little to no treatment before discharge is considered a common practice, and this has led to the eventual leaching of contaminants into the soil, which causes the significant depletion of groundwater quality [3]. All of these, in addition to unexpected climate change and the indiscriminate use of groundwater, have put pressure on groundwater resources in various aspects and created an imbalance in groundwater hydrology [4]. These contaminations will deteriorate the groundwater quality, which makes it unsafe to be used and results in adverse health effects.
Owing to the slow movement of groundwater flow, polluted groundwater takes a very long time to purify as it takes a more extended period to flush out the contaminants. Groundwater quality and its characteristics hugely depend on the nature of the soil through which the water percolates, as well as the rock matrix comprising the aquifer. Chemical characteristics such as groundwater mineralogical composition; contact time between the groundwater and its surroundings; the chemical phases through the rock formation process; water temperature and pressure; and other factors including its pH, the presence of organic matter, and dissolved oxygen can be useful in determining the degree of contamination in a groundwater system [5].
Malaysia’s total groundwater reserve is reported to be 5000 billion cubic meters, which is nine times the volume of water flowing into Malaysian rivers annually [6]. Around 70% of the total groundwater usage in Malaysia is served for domestic purposes, 25% for industrial usage, and the remainder for agricultural uses. In 2008, the extraction of groundwater in Selangor alone was estimated to be approximately 10.8 billion liters, with more than 300 active tube wells recorded, most of which could be found in schools and mosques, as well as in industrial and rural areas [7]. The demand for groundwater usage has increased in this country due to several reasons such as the lower cost and effort required for its extraction, causing many factories and other consumers to start to shift their freshwater sources to groundwater [8]. Apart from that, potable water is a critical component for human survival. Hence, its dependence should not only focus on surface water sources for meeting this requirement but also on alternative water sources such as groundwater.
Despite the rising cases of groundwater contamination and the proven importance of clean groundwater resources, research exploration focusing on Malaysian groundwater contamination is still scarce, while it is crucial for evaluating the quality and suitability of groundwater for various utilitarian purposes [9]. This is in accordance with the Strategies to Enhance Water Demand Management in Malaysia under strategy 19, which highlighted several points for groundwater, which include undertaking detailed groundwater assessment studies to develop and maintain the groundwater for use in emergencies and in major urban areas in relatively dry regions [10]. The necessity of this study is aligned with sustainable development goals (SDG), which ensure the availability and sustainable management of water and sanitation for all. Aside from that, most groundwater studies reported in Malaysia show a focus on island-based discussion, while 40% of groundwater studies focus on inland study areas. Table 1 summarizes the available inland groundwater contamination studies in Malaysia. From that, it is observed that contamination concentrated around landfill areas has become a popular subject for inland groundwater contamination studies; moreover, the previous researchers have discussed more about geophysical investigation. The lack of comprehensive hydrogeochemical studies in these studies has resulted in a limited understanding of groundwater chemistry variation, where additional factors such as intensive agriculture in coastal areas and excessive chemical fertilizer application could have a negative impact on water quality. Groundwater chemical composition alone may not be able to distinguish between natural and anthropogenic factors. The exploration of groundwater contamination involves processing a variety of parameters and factors leading to a complex and broad data collection [11]. Hence, the identification of the mechanisms and the determination of the most critical factors responsible for hydrogeochemistry require a powerful data interpretation tool. Through modern approaches such as multivariate analysis, it is possible to identify the variables that affect the outcomes, thereby offering a more accurate conclusion including apportioning pollution sources/factors (natural or anthropogenic), designing a monitoring network for effective water resource management, and finding practical solutions to pollution problems. This current study shows the relevance of this research application and will eventually fill the existing gap in evaluating the factors contributing to the pollution of groundwater.
It is necessary to conduct a comprehensive groundwater quality analysis, as it can help to identify the sources of the factors that influence groundwater quality, and the results can be used as reference data and initial guidance for decision-making and mitigation schemes for pollution control and technology by the relevant authorities [26,27,28]. The use of spatial analysis has made assessing environmental issues, such as groundwater, much easier [29]. Furthermore, the outcomes of this study will provide the information used to alert society to the importance of maintaining a pollutant-free groundwater system. Hence, the aims of the study are (i) to demonstrate the variation in the hydrogeochemistry of the Langat basin and (ii) to identify the most significant factor or source that influences the groundwater quality along the Langat Basin through a statistical approach. This study attempts to elucidate the spatial distribution of the groundwater quality of the Langat Basin along with the groundwater contamination. The results will later be compared with the appropriate national or international standard to ascertain its suitability as a water source.

2. Materials and Methods

2.1. Study Area

The Langat Basin is located on the west side of Peninsular Malaysia. It is a flat lowland with a catchment area of 1815 km2. The estimated total area of the Langat Basin is 2350 km2. The basin is drained by four large sub-basins, which are the Langat River, the Labu River, the Semenyih River, and the Beranang River, which flow west to the Strait of Melaka. The basin is among one of the most urbanized basins in Malaysia and is a highly developed urban zone. The Langat Basin consists of the Kuala Langat, Ulu Langat, and Sepang districts. In 1995, the population of the Langat Basin was 1,050,990, and this number has risen significantly over the years, with the total population of the studied area in 2019 being reported as 1,928,000 [30]. The increasing trend in the population has occurred due to several factors, which include rapid development, the migration of residents from other districts, and the economic conditions in the Langat Basin. There is an average of 22 industrial categories operating around the Langat Basin alone, with electrical and electronic industries dominating the area, followed by manufacturing industries, with at least 337 factories actively operating in this basin.
The geology of the Langat Basin consists of the oldest known rocks (Middle Cambrian or earliest Paleozoic), which include granite, alluvium, sedimentary, and volcanic rocks [31]; the alluvium was found to be consisting of sand, clay, gravel, and silt. The Langat mountainous areas consist of Permian igneous rock and pre-Devonian schist and phyllite [32]. Meanwhile, the lowland part of the Langat Basin is formed from unconsolidated gravel, sand silt, and clay formations. The formation of Kenny Hill and the Kajang formation was build up from sandstone, phyllite, shale, and quartzite [7]. The study area’s aquifer system is made up of alluvial sand, silt, and gravel deposits that form a shallow, confined aquifer, with the unsaturated zone of the aquifer consisting of clay with a thickness ranging between 1 and 3 m [33]. Most of the aquifer ranges from 5 to 80 m in depth. Table 2 shows the geological profile setting of the Langat Basin. The groundwater of the Langat Basin is replenished from the rainfall and river water by (1) downward flow through the aquitard, (2) the intrusion of water along the surfaces of geological outcrops where the aquitard is shallow or unavailable, (3) intrusion from comparatively more porous bedrock, (4) penetration from river bottoms in areas where the river floor is in contact with more porous sand horizons, and (5) intrusion from wetlands and brackish water where the higher aquifer and the aquitard have been removed and replaced by more permeable materials [34].
The Langat Basin has a tropical climate with humid, hot, and wet season conditions throughout the year. The basin is influenced by two types of monsoons, namely the northeast (November–March) and the southwest (May–September) [35]. It receives an annual rainfall ranging from 1500 to 2900 mm (Table 3). The average temperature throughout the year is 27 °C, with high temperatures expected around April and May, while low temperatures occur in November and December. Forty-five groundwater samples were collected from 15 different sampling stations distributed evenly across the Langat basin. The land use of the studied area is approximately comprised of landfill, plantation, residential, and coastal areas. This study was conducted in July 2018. Most of the sampling stations were located in areas that practice industrial and agricultural activities (Table 4). Figure 1 shows the location and the distribution of groundwater sampling stations in the Langat Basin.

2.2. Physicochemical Parameter, Major Ions, and Heavy Metals

The sampling locations were determined during the site reconnaissance survey with a sampling design that focused on spatial variations. A total of 45 groundwater samples were collected from 15 boreholes labeled LW1 to LW15 (Figure 1). The groundwater samples were pumped out for about 10–15 min to eliminate stagnant water that could interfere with the analysis of the experiment. During the sampling activities, the in situ data measurements were assessed to obtain a representative measure of the quality of the water and to prevent any possibility of biochemical changes occurring in the samples. In this research study, physicochemical parameters were obtained with triplicate measurement, and the studied parameters involved temperature (Temp, °C), electrical conductivity (EC, µS/cm), total dissolved solids (TDS, mg/L), salinity (ppt), pH level, and dissolved oxygen (DO, mg/L). In situ analyses were measured using a multi-parameter probe YSI 556. All of the probes were calibrated with buffer solutions before and after the sampling to ensure that they functioned accurately and to prevent erroneous measurements from occurring. For major anion analysis, the groundwater samples collected were un-acidified and non-filtered with the exception of sulfate (SO42−), which required filtered samples to determine its concentration. The filtered groundwater samples had SulfaVer 4 reagent powder pillow added, which formed a white precipitate with the presence of SO4. The amount of precipitate formed was proportional to the concentration of the SO4, which was detected using a HACH spectrophotometer (DR/2500 HACH Odyssey, Loveland, CO, USA). Bicarbonate (HCO3) and chloride (Cl) were measured by the titration method according to the standard American Public Health Association method [36].
Concerning the major cations and heavy metals, the groundwater samples were filtered using a 0.45 µm millipore filter (Whatman Milipores, Clifton, NJ, USA) and acidified with nitric acid before being transported to the laboratory of the Faculty of Forestry and Environment, Universiti Putra Malaysia for further analysis. The acidification process was carried out to reduce any chance of precipitation, adsorption, or bacterial activities that would affect the outcome of the results. Groundwater samples were stored and kept at 4 °C to minimize and reduce potential microbial activity in the water samples [37]. The studied heavy metals were iron (Fe), manganese (Mn), arsenic (As), copper (Cu), lead (Pb), zinc (Zn), cadmium (Cd), chromium (Cr), mercury (Hg), nickel (Ni), and selenium (Se). Major ions and heavy metals were analyzed using inductively coupled plasma mass spectrometry (ICP-MS, ELAN DRC-e, Perkin Elmer, Shelton, CT, USA). A variety of standard solutions were freshly prepared using stock standard solutions diluted (ICP Multi-Element Mixed Standard III, Perkin Elmer) with Milli-Q water.

2.3. Data Analysis

2.3.1. Statistical Analysis

The statistical data analysis was carried out using the application of IBM SPSS Statistic 23 software version (International Business Machines, New York, USA) to perform univariate analysis and multivariate statistical techniques such as correlation analysis, principal component analysis (PCA), and hierarchical cluster analysis (HCA). The collected data were subjected to descriptive statistics analysis present by its mean and standard deviation. Correlation coefficient analysis was performed to study the association of the parameters with each other [38]. PCA and HCA are reported to be helpful supplemental tools for identifying similarities among geochemical behaviors or common sources for chemicals in groundwater [39,40,41]. Each sampling station was attributed to a large number of physicochemical variables, which make the regional hydrogeochemical study a multivariate problem [42]. Additionally, it was used for evaluating statistical data and identifying the source of the pollutants. There are several methods for determining the limit of detection (LOD) in the analysis. The most commonly used is treating the LOD value as the absolute value (for example, if the limitation was <0.5, then the value of 0.5 would be used); secondly, the researchers would treat the LOD values as zero; third, the LOD values would be excluded from the data set; and finally, the LOD value would be substituted with a value between zero and the LOD value (new average value) [43]. For the current study, this practice was the first choice, but fortunately, all parameters for each station had solid concentration values (Tables S1–S3).

2.3.2. Hydrochemical Facies

Hydrochemical facies of the groundwater can be better explained through the plotting of major cations and anions using a piper trilinear diagram from the application of GW Chart software 1.30.0 software [44,45,46]. It explains the variation of the dominance of anion and cation concentrations. It is also one of the graphical methods that are most commonly used in groundwater chemistry studies [47].

2.3.3. Hierarchical Analysis Component (HCA)

An HCA produces classes that group the groundwater sampling locations or studied quality parameters for enabling a better interpretation of the origin of groundwater contamination [48]. Ward’s method is one of the most common methods used in applying the HCA. The interpretation can be made through the visual inspection of the dendrogram produced by the HCA [49]. The application of an HCA has been widely used in hydrogeochemical studies by grouping the studied parameters based on their similarities [50].

2.3.4. Principal Component Analysis (PCA)

Principle component analysis (PCA) is a powerful multivariate statistical technique used for reducing a large number of variables into smaller components to help interpret data quickly [51]. It provides important information for the whole data set while maintaining the relationships in the original data. The varimax method was applied to execute the rotation of the PCA, and where the PCs had an eigenvalue greater than 1.00, they were retained and discussed. The strength of the physicochemical parameter loading is classified as ‘strong’ (>0.75), ‘moderate’ (0.75 to 0.50), or ‘weak’ (0.50 to 0.30) [52].

3. Results and Discussion

3.1. Descriptive Analyses

3.1.1. Physicochemical Properties of the Groundwater in the Langat Basin

The descriptive statistics of the hydrogeochemistry of the Langat Basin are outlined in Table 5. Most of the variables range widely, thereby specifying the complexity of the hydrogeochemical conditions occurring in the groundwater. The pH values varied from 4.40 to 7.42 (Table S1), indicating a range between acidic to basic conditions of the groundwater. This condition may be attributed to the application of fertilizer in the surrounding plantation areas, which seeps into the groundwater. Additionally, the low pH value in the study area, showing acidic conditions, is most probably caused by the close distance to the recharge area and, in part, by saltwater intrusion [53,54]. Moreover, the occurrence of natural processes such as water flowing through non-carbonate rock leads towards the range of the recorded pH values. Aside from the presence of an alluvial aquifer in the basin, 73% of the Langat Basin is comprised of the acid intrusive geological unit, which may contribute to the following event [55]. Besides, the experience of an unpleasant odor of rotten eggs, or H2S, in some of the sampling stations could be the chemical reaction of the product of SO4 reduction where pH values fluctuate. H2S describes the anaerobic process in the groundwater that produces the unpleasant odor and could responsible for the pH fluctuation and also subject to the SO4 concentration in the groundwater. The groundwater temperature ranged between 28.10 °C and 31.10 °C.
Meanwhile, the DO values ranged from 0.70 mg/L to 2.19 mg/L. The depletion of DO values in the groundwater was influenced by the intrusion or existence of waste discharges or natural organic matter into the groundwater system. The Langat Basin is predominantly occupied by industrial activities dominated by manufacturing activities and plantation activities, and this may have led to the discharge of contaminants from these activities into the groundwater system [56,57]. Furthermore, agricultural activities make up 60% of the total area of the Langat Basin, with many types of pesticides being applied to optimize agricultural production [8]. Thus, the stations in close proximity to these areas have a high tendency to be exposed to the pollution produced by these sources, thus exhibiting low DO values. LW10 experiences high salinity, TDS, and EC values as the location is near to coastal and agricultural activities (Table S1). This has exposed the area to saltwater intrusion and fertilizer seepage [58,59].

3.1.2. Major Ions Distribution in the Langat Basin

The abundance of major ions was in the following order: HCO3− > Cl > Na+ > SO42− > Ca2+ > K+ > Mg2+ (Table S2). The concentration of HCO3− might have been influenced by mineral dissolution such as water–rock interaction, carbonate minerals, or weathering processes that occur in the groundwater [60]. The Cl concentration for the present study ranged between 19.99 mg/L and 499.85 mg/L, while SO42− readings ranged between 0.07 mg/L and 244 mg/L, with all the water samples found containing SO42− is below the set limit of 250 mg/L [61,62]. SO42− naturally exists in most of the freshwater, but its presence may originate from the application of ammonia sulphate fertilizers in agricultural activities as the basin is dense with agricultural activities. Cl ions are one of the most important inorganic anions in the groundwater, and may present in the groundwater systems through wastewater, chemical fertilizers, irrigation, or industrial effluents [52]. Since some of the sampling points have high Cl values, the elevated levels of Cl will lead to problems, including an increase in water corrosivity and taste interference [5].
Mg2+ concentration was found to be between 0.21 mg/L and 25.85 mg/L, and none of the groundwater samples exceeded the limit of 100 mg/L [62]. Mg2+ could be originated from carbonate minerals or weathering and leaching processes. For Na+, the average threshold is 200 mg/L. High levels of Na+ in the groundwater are related to the aquifer recharge from lateral limestone formations or clays by cation exchanges or silicate weathering [63]. The domination of cations found in the studied area shows that the sources are silicate weathering and agricultural runoff [64,65]. The concentration of Ca2+ ranged between 0.05 mg/L and 82.65 mg/L. It is commonly found as part of the alkaline earth metal and rock mineral components or from calcium carbonate (CaCO3) and dolomite (CaMg(CO3)) [66]. The current study indicates that Ca2+ is introduced to the groundwater through the weathering of silicate and limestone alterations. The lithology of the Langat Basin comprises six geological units, including limestone [55]. The K+ value varied between 0.92 mg/L and 40.51 mg/L. A higher concentration of K+ at certain stations indicates that it was derived from the effluent coming from either industrial activities or fertilizer application from the agricultural areas [40].

3.1.3. Occurrences and Distribution of Heavy Metals in the Groundwater of the Langat Basin

The order of heavy metal dominance is as follows: Fe > Mn > Zn > As > Hg > Pb > Ni > Cu > Cd > Se > Cr (Table S3). All the groundwater samples were found to be within the limit set by the Ministry of Health Malaysia [62] and the World Health Organization [61], except for Hg, Mn, and Fe (Table 5). The analysis of the spatial distribution of Hg indicates that the highest concentration was in the areas of residential, coastal, and agricultural practices. Considering that the geology of the Langat Basin consists of pre-Cambrian rock, Hg may originate naturally in the groundwater, but at low concentrations. The Langat Basin has a high amount of industrial activities, which may lead to the atmospheric emission of Hg, which later accumulating in the soil and water [67]. This can be worsened by the wind flow and direction; Malaysia in particular is highly influenced by the tropical monsoon season [68]. The concentrations of Hg in the Langat Basin groundwater are comparatively higher than the maximum Hg detected in other regions such as the Isonzo River Alluvial, Italy (0.0008 mg/L) and Revdalin, Norway (0.0001 mg/L) [69,70]. This can be explained by the urban density development and the site area’s historical land use. The Pearl River Delta, similar to the Langat Basin, was influenced by industrialization in urban and peri-urban areas, with elevated Hg concentrations three times higher than the Hg concentrations in rural areas [39]. However, studies focusing on the occurrences of Hg in urban areas are still scarce, and more attention in future studies is needed for a better understanding regarding the sources, transportation, and fate in groundwater of Hg.
The variation of heavy metal concentrations between stations is probably attributed to the distance factor. The groundwater systems that experienced an increase in contaminants were located closer to pollution sources such as agricultural activities and industrial activities. Fe shows the highest abundance among other types of heavy metals, due to it being among the abundant elements making up the earth’s crust and also being released through intermixed processes such as water–rock interaction and anthropogenic activities [71]. The increased Fe intensity in groundwater is linked to natural origins such as chemical processes in rocks and biological systems. Meanwhile, Mn is considered among the “macro-elements”, which indicates that these elements were by ‘land-based’ discharge, which leads to its release into the groundwater [72]. Other than that, some of the sampling stations were located near industry, urban, and agricultural areas. Anthropogenic activities, such as piping services for industrial and domestic uses, are other potential sources that could have led to these variations in concentration. This includes metals, in particular Mn, which are used in the production of steel. Moreover, metals are widely used in industry, and the corrosion from underground steel pipelines also transfers these elements into the aquifer [54]. The other heavy metals may originate naturally due to geological features or through anthropogenic activities such as direct leachate percolation from landfills and industrial waste dumping [47].

3.2. Correlation Matrix

The correlation coefficient between physicochemical parameters was evaluated to determine any significant variations between the variables (Table 6). A robust positive correlation coefficient was found between TDS-Sal, TDS-EC, and Sal-EC (r = 1.000, p < 0.01). EC measures the ability of the water to transmit electric current by dissolved ions. Meanwhile, TDS is described as the sum of ions, cations, and anions in the water. Hence, TDS could indicate the behavior of the EC of the water [73]. It is also used to reflect the salinity of the groundwater. Therefore, salinity, TDS, and EC are correlated to each other, in which the increase of one gives rise to another. HCO3 also shows a moderate positive correlation with TDS, EC, and salinity r = 0.625 to 0.641 (p < 0.01). The moderate correlation between TDS, EC, and salinity and HCO3 suggests that this type of ion mostly controls these parameters. HCO3 shows a strong correlation with Cl (r = 0.761, p < 0.01). Thus, it suggests that these ions may come from the same source, which might indicate the chemical characteristics of a meteoric water mix, with water coming from anthropogenic activities [74].
A positive correlation was found between SO4 with Cl (r = 0.544) at a significant level p < 0.01. A moderate relationship between these major salinity components, SO42− with C, indicates that it either occurs due to saltwater intrusion in the groundwater system or is discharged from industrial and agricultural activities [73]. Na, K, Mg, and Ca show a positive and significant correlation with each other (r = 0.689 to 0.981) at a significant level p < 0.01. The anions may reflect the occurrence of silicate weathering in the groundwater system, as this process can release major cations into the groundwater [75]. It was also found that these ions might present in the groundwater through anthropogenic brine [47]. A positive correlation (r = 0.981, p < 0.01) of Mg-K may signify the leaching of salts from secondary salts [66]. Na-K strong positive correlation (r = 0.930, p < 0.01) signifies that these ions have a common origin, where the presence of these ions may come from clay [76]. Mg-Na correlation (r = 0.915, p < 0.01) reflects the occurrence of cation exchange between Mg and Na occurring in the groundwater system.
The Pearson correlation performed for heavy metals with physicochemical parameters shows that they have a moderate correlation with each other. This may reflect that these elements did not originate from single sources [77]. Instead, the presence of these heavy metals may be due to various anthropogenic processes and geogenic processes [78]. Some of the metals show a strong positive relationship with other elements and parameters. Mn was found to have strong positive correlation with TDS (r = 0.820, p < 0.01), salinity (r = 0.832, p < 0.01), and EC (r = 0.827, p < 0.01). This may reflect that these parameters were influenced by the concentration of Mn. Se and Fe also showed a moderate correlation with some of the studied parameters (Table 6). The varied correlation between heavy metals and pH is related to the mobility of the heavy metals. This is dependent on the psychochemical parameters, where the solubility of the heavy metals increased with the decrease of pH values, which clarifies that the correlation occurs between heavy metals and physicochemical parameters. Fe is highly correlated with Mn, which suggests that they might come from a common source [79]. Fe and Mn can be released from geogenic sources as they are common elements in rocks and minerals [80,81]. Cd showed a moderate correlation with Zn (r = 0.549, p < 0.01) and Pb (r = 0.548, p < 0.01). These demonstrate that these heavy metals may originate from the same industrial activities, such as through leachate release [81].

3.3. Hydrochemical Facies

The hydrochemical facies of the groundwater samples were Na-HCO3 (Circle I) and Na-Cl (Circle II) water types (Figure 2). A Na-HCO3 water type suggests that there is an occurrence of water–rock interaction in the groundwater system [82]. Na-HCO3 presence is due to the cation exchange process with clay and clay minerals. Generally, it shows mix-water type characteristics [83]. Meanwhile, the Na-Cl water type that dominates the groundwater indicates a saline water type. The source for this water type is likely due to the salt deposits from agricultural activities that flow into the groundwater [55]. However, this also suggests that it is probably governed by silicate weathering and mineral dissolution [80]. Na+ and Cl may also originate from clay materials, which may introduce these ions into the groundwater system, hence influencing the water type [84]. The piper plot reveals that the groundwater chemistry of the Langat Basin belongs to the Na-HCO3-Cl water type. This mixing is also directed to the freshwater mixed with saline that is influenced by agricultural, urban, and industrial activities that contribute to the salinization of the groundwater.
The Gibbs diagram (Microsoft Corporation, Washington, USA) [85] is an important tool for evaluating the functional source of dissolved ions in water such as the dominance of precipitation, rock weathering, and evaporation dominance that govern the water chemistry. From the plots, it is evident that the groundwater chemistry of the Langat Basin has not been regulated by any dominant mechanism (Figure 3). The Gibbs diagram plot revealed that anions of the groundwater samples had been driven by rock weathering processes. The presence of HCO3 in the groundwater occurs due to the dissolution of rock weathering processes [60]. It was also revealed that precipitation factors and anthropogenic activities have also played a role in the cation concentration in the groundwater. Anthropogenic activities may have introduced not only HCO3 but also Cl into the groundwater of the Langat Basin through the precipitation process, consequently leading to elevated concentrations of both anions in the groundwater, especially in the wells labeled LW10, LW11, LW13, and LW14. It is also evident that the ionic mechanism of cations in the groundwater of the Langat Basin appears to be influenced mostly by rock-weathering and anthropogenic processes. The groundwater samples that fell outside of the diagram are suggested to have been influenced by anthropogenic mechanisms [58]. Despite the inclusion of anthropogenic processes, the cations in the groundwater system are still within the limits.

3.4. Principal Component Analysis (PCA)

PCA helps to determine the most significant factors that account for the significant patterns [86]. The Kaiser–Meyer–Olkin (KMO) test values of 0.557 and Barlett’s test of sphericity (p < 0.001) showed that the data were sufficient for analysis using PCA [87]. PCA produced four major components with eigenvalues, explaining 81% of the variance in the data set (Figure 4). PC1 explained 26.97% of the total variance, with a strong positive loading found for all major cations, which were K+, Mg2+, Na+, and Ca2+. The loading of the major cations indicates that the weathering of rock minerals occurred in the groundwater [26]. Cations are commonly presented in clay minerals and become a source for groundwater through silicate weathering or carbonate weathering. Nevertheless, this may also be attributed to the anthropogenic activities adjacent to the land use [50]. PC2 accounts for 26.83%, with the loading showing a strong positive loading between TDS, salinity, and EC. This represents that the same factor might influence these parameters. Based on the findings, these parameters show a moderate correlation with HCO3, and this suggests that the parameters are directly affected by this ion (Table 7) (Figure 5).
PC3 exhibits a moderate to strong positive loading of major anions (HCO3, SO42− and Cl) with a total variance of 17.89% The interaction between water, soils, and rock and the weathering of silicate might result in releasing major anions into the groundwater [56,88]. The presence of this ion may be due to anthropogenic activities that introduce these ions into the water body, mostly through the application of chemical fertilizers in agricultural activities [89,90]. The presence of HCO3 can be due to the decaying of soil organic matter incorporated with the dissolving of CO2, reflecting the influence of fertilizer [91]. PC1 to PC3 might imply that these loadings are related to anthropogenic and natural occurrences. PC4 explains 8.88% of the total variance and is characterized by the moderate loading of pH and DO and the negative loading of temperature. This represents that the high value for DO and pH is more likely at low-temperature values. For the pH level, ionization might occur where the H+ in solution will decrease with temperature and increase the pH level. As for the inverse relationship between DO and temperature, this is due to the solubility of oxygen in the water.

3.5. Hierarchical Component Analysis (HCA)

HCA classified the sampling stations into two major clusters, with 80% of the stations belong to cluster 1 and the other stations being classified under cluster 2 (Figure 6). Cluster 1 consists of stations LW1 to LW9, LW12, LW13, and LW15. In this cluster group, the sampling stations had lower pollution levels. It was found that the stations belonging to this cluster were located far from pollution sources such as industrial discharge, construction projects, or farming activities. These sampling stations were therefore less exposed to groundwater pollution, which is supported by the results obtained from the present study, which show that almost all of the stations in this cluster did not exceed any permissible limit established by the World Health Organization (WHO) and Ministry of Health Malaysia (MOH).
Cluster 2 consists of the sampling stations LW10, LW11, and LW14; these stations have been recognized as having a mix-water type. LW10 was located near the coastal area, whereas stations LW11 and LW14 were located in an area that was close to a palm oil plantation and a residential area. Station LW11 was also located within an area with active farming activities, and a construction site was also located nearby to station LW14. Station LW14 had the highest Cl value, which might be attributed to the nearby agricultural activities (Table S2) (Figure S1). The Langat Basin comprises the alluvial aquifer, and the groundwater recharge in the alluvial aquifer occurs via a few mechanisms, such as the direct infiltration of rainfall and the return flow of irrigated water [92]. These mechanisms will introduce pollutants to the groundwater system through seepage.

4. Conclusions

The hydrogeochemical characteristics and the processes affecting the chemistry of the groundwater of the Langat Basin have been evaluated based on the physicochemical parameters and the major ions. The current study revealed that the dominant cations were Na+ > K+ > Mg2+ > Ca2+, while the dominant anions were HCO3 > Cl > SO42−. The water types found in the groundwater system were Na-HCO3, Na-Cl, and Na-HCO3-Cl. The TDS and EC in certain wells (stations LW9, LW10, LW11, LW13, and LW14) exceeded permissible limits and showed high values reflecting that the groundwater was unfit to use without proper treatment and management. The dominance of heavy metals was as follows: Fe > Mn > Zn > As > Hg > Pb > Ni > Cu > Cd > Se > Sr. For the studied heavy metals, only Hg was found to exceed the permissible limits. Natural and anthropogenic activities, specifically industrial and agricultural activities, have demonstrated an effect and dominant influence over the Langat Basin’s groundwater chemistry. Most of the sampling stations with contaminated groundwater were located near pollution sources.
Considering the intense industrialization and urbanization in the Langat Basin, it is crucial to have continuous monitoring and risk assessments to prevent future deterioration of the groundwater and to develop practical groundwater management. The findings of the study are decisive in evaluating the current quality of the groundwater and the sources of contamination of the groundwater system. Despite most of the parameters being below the permissible limits, the contaminants found were significant. The results could help to design more efficient land development to reduce groundwater contamination. Furthermore, the multivariate analysis approach is important for understanding the environmental condition, allowing for the evaluation of the ecological risk of groundwater, and assisting in identifying the priorities for sustainable groundwater management, specifically in the tropical basins in other parts of the region. Future groundwater quality studies for carrying out seasonal sampling in the Langat Basin are recommended.

Supplementary Materials

The following are available online at https://www.mdpi.com/article/10.3390/ijerph18115733/s1, Table S1: Descriptive analysis for in-situ parameters., Table S2: Major ions descriptive analysis., Table S3. Heavy metals descriptive analysis. Figure S1. Major ions concentration distribution along with sampling station.

Author Contributions

Writing—original draft, investigation and visualization, N.F.M.Z.; writing—review and editing A.H.Z., L.J.L. and A.Z.A.; methodology, conceptualization, and format analysis, N.F.M.Z. and N.M.I.; validation, L.J.L., A.Z.A., N.M.I. and K.M.K.K.Y.; sampling design, A.S.; supervision, funding acquisition, and project administration, N.M.I.; resources, A.S. and N.M.I.; data analysis, K.M.K.K.Y. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Grant Putra-GP IPM/2018/9592700 from Universiti Putra Malaysia.

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

Not applicable.

Acknowledgments

This research was funded by the Grant Putra-GP IPM/2018/9592700 from Universiti Putra Malaysia. The authors gratefully acknowledge all the people involved in this study. Special thanks and gratitude to all fellow research members, the staff of the Faculty of Forestry and Environment, and the National Water Research Institute of Malaysia for their assistance and guidance.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Giordano, M. Global Groundwater? Issues and Solutions. Annu. Rev. Environ. Resour. 2009, 34, 153–178. [Google Scholar] [CrossRef]
  2. Zainuddin, A.H.; Wee, S.Y.; Aris, A.Z. Occurrence and potential risk of organophosphorus pesticides in urbanised Linggi River, Negeri Sembilan, Malaysia. Environ. Geochem. Health 2020, 1–13. [Google Scholar] [CrossRef]
  3. Usman, U.N.; Toriman, M.E.; Juahir, H. Assessment of Groundwater Quality Using Multivariate Statistical Techniques in Terengganu. Sci. Technol. 2015. [Google Scholar] [CrossRef]
  4. Gude, V.G. Desalination of deep groundwater aquifers for freshwater supplies–Challenges and strategies. Groundw. Sustain. Dev. 2018, 6, 87–92. [Google Scholar] [CrossRef]
  5. Sayyed, J.A.; Bhosle, A.B. Analysis of Chloride, Sodium and Potassium in Groundwater Samples of Nanded City in Mahabharata, India. Eur. J. Exp. Bio. 2011, 1, 74–82. [Google Scholar]
  6. Abdullah, S.; Chand, F.; Zakaria, S.; Loganathan, P. Transforming the Water Sector: National Integrated Water Resources Management Plan. Strategies and Road Map Volume 2—Appendices. J. Chem. Inf. Modeling 2019, 53. [Google Scholar] [CrossRef]
  7. Mridha, G.C.; Hossain, M.M.; Uddin, M.S.; Masud, M.S. Study on availability of groundwater resources in Selangor state of Malaysia for an efficient planning and management of water resources. J. Water Clim. Chang. 2019, 11, 1050–1066. [Google Scholar] [CrossRef] [Green Version]
  8. Mohamed, A.F.; Yaacob, W.W.; Taha, M.R.; Samsudin, A.R. Groundwater and soil vulnerability in the Langat Basin Malaysia. Eur. J. Sci. Res. 2009, 27, 628–635. [Google Scholar]
  9. Kusin, F.M.; Azani, N.N.M.; Hasan, S.N.M.S.; Sulong, N.A. Distribution of heavy metals and metalloid in surface sediments of heavily-mined area for bauxite ore in Pengerang, Malaysia and associated risk assessment. Catena 2018, 165, 454–464. [Google Scholar] [CrossRef]
  10. Academy of Sciences Malaysia. Strategies to Enhance Water Demand Management in Malaysia, 2016. Available online: www.akademisains.gov.my/asm-publication/water-demand-management/ (accessed on 17 February 2021).
  11. Bodrud-Doza, M.D.; Islam, A.T.; Ahmed, F.; Das, S.; Saha, N.; Rahman, M.S. Characterization of groundwater quality using water evaluation indices, multivariate statistics and geostatistics in central Bangladesh. Water Sci. 2016, 30, 19–40. [Google Scholar] [CrossRef] [Green Version]
  12. Crowther, J. Groundwater chemistry and cation budgets of tropical karst outcrops, Peninsular Malaysia, I. Calcium and magnesium. J. Hydrol. 1989, 107, 169–192. [Google Scholar] [CrossRef]
  13. Ahmed, A.M.; Sulaiman, W.N. Evaluation of groundwater and soil pollution in a landfill area using electrical resistivity imaging survey. Environ. Manag. 2001, 28, 655–663. [Google Scholar] [CrossRef]
  14. Samuding, K.; Abustan, I.; Rahman, M.T.A.; Isa, M.H. Distribution of Heavy Metals Profile in Groundwater System at Solid Waste Disposal Site. Eur. J. Sci. Res. 2009, 37, 58–66. [Google Scholar]
  15. Rahim, B.E.A.; Yusoff, I.; Samsudin, A.R.; Yaacob, W.Z.W.; Rafek, A.G.M. Deterioration of groundwater quality in the vicinity of an active open-tipping site in West Malaysia. Hydrogeol. J. 2010, 18, 997–1006. [Google Scholar] [CrossRef]
  16. Kato, M.; Onuma, S.; Kato, Y.; Thang, N.D.; Yajima, I.; Hoque, M.Z.; Shekhar, H.U. Toxic elements in well water from Malaysia. Toxicol. Environ. Chem. 2010, 92, 1609–1612. [Google Scholar] [CrossRef]
  17. Taha, M.R.; Yaacob, W.Z.W.; Samsudin, A.R.; Yaakob, J. Groundwater quality at two landfill sites in Selangor, Malaysia. Bull. Geol. Soc. Malays. 2011, 57, 13–18. [Google Scholar] [CrossRef]
  18. Islami, N.; Taib, S.H.; Yusoff, I.; Ghani, A.A. Integrated geoelectrical resistivity, hydrochemical and soil property analysis methods to study shallow groundwater in the agriculture area, Machang, Malaysia. Environ. Earth Sci. 2012, 65, 699–712. [Google Scholar] [CrossRef]
  19. Ashraf, M.A.; Yusoff, I.; Yusof, M.; Alias, Y. Study of contaminant transport at an open-tipping waste disposal site. Environ. Sci. Pollut. Res. 2013, 20, 4689–4710. [Google Scholar] [CrossRef] [PubMed]
  20. Juanah, M.S.E.; Ibrahim, S.; Sulaiman, W.N.A.; Latif, P.A. Groundwater resources assessment using integrated geophysical techniques in the southwestern region of Peninsular Malaysia. Arab. J. Geosci. 2013, 6, 4129–4144. [Google Scholar] [CrossRef]
  21. Shirazi, S.M.; Imran, H.M.; Akib, S.; Yusop, Z.; Harun, Z.B. Groundwater vulnerability assessment in the Melaka State of Malaysia using DRASTIC and GIS techniques. Environ. Earth Sci. 2013, 70, 2293–2304. [Google Scholar] [CrossRef]
  22. Shamsuddin, M.K.N.; Sulaiman, W.N.A.; Suratman, S.; Zakaria, M.P.; Samuding, K. Groundwater and surface-water utilisation using a bank infiltration technique in Malaysia. Hydrogeol. J. 2014, 22, 543–564. [Google Scholar] [CrossRef]
  23. Mogaji, K.A.; Lim, H.S.; Abdullar, K. Modeling groundwater vulnerability to pollution using Optimized DRASTIC model. IOP Conf. Ser. Earth Environ. Sci. 2014, 20. [Google Scholar] [CrossRef] [Green Version]
  24. Atta, M.; Yaacob, W.Z.W.; Jaafar, O.B. The potential impact of leachate-contaminated groundwater of an ex-landfill site at Taman Beringin Kuala Lumpur, Malaysia. Environ. Earth Sci. 2015, 73, 3913–3923. [Google Scholar] [CrossRef]
  25. Haque, S.; Roslan, N. Groundwater Quality Aspect Owing to Urbanization in Langat Basin (Kajang, Semenyih) Malaysia. Asian J. Environ. Ecol. 2017, 4, 1–9. [Google Scholar] [CrossRef]
  26. Machiwal, D.; Jha, M.K. Regional Studies Identifying sources of groundwater contamination in a hard-rock aquifer system using multivariate statistical analyses and GIS-based geostatistical modeling techniques. J. Hydrol. Reg. Stud. 2015, 4, 80–110. [Google Scholar] [CrossRef] [Green Version]
  27. Gunaalan, K.; Ranagalage, M.; Gunarathna, M.; Kumari, M.; Vithanage, M.; Srivaratharasan, T.; Saravanan, S.; Warnasuriya, T.W.S. Application of geospatial techniques for groundwater quality and availability assessment: A case study in Jaffna Peninsula, Sri Lanka. ISPRS Int. J. Geo Inf. 2018, 7, 20. [Google Scholar] [CrossRef] [Green Version]
  28. Vasileiou, E.; Papazotos, P.; Dimitrakopoulos, D.; Perraki, M. Expounding the origin of chromium in groundwater of the Sarigkiol basin, Western Macedonia, Greece: A cohesive statistical approach and hydrochemical study. Environ. Monit. 2019, 1–34. [Google Scholar] [CrossRef] [PubMed]
  29. Pande, C.B.; Moharir, K. Spatial analysis of groundwater quality mapping in hard rock area in the Akola and Buldhana districts of Maharashtra, India. Appl. Water Sci. 2018, 8, 1–17. [Google Scholar] [CrossRef] [Green Version]
  30. DOSM. Poket Stats Negeri Selangor ST 2 2020. Jabatan Perangkaan Malaysia. 2020. Available online: www.dosm.gov.my/v1/index.php?r=column/cone&menu_id=dFc3aExhVktPbUpoZys1dWoyUWFPQT09# (accessed on 10 October 2018).
  31. Nampak, H.; Pradhan, B.; Abd, M. Application of GIS based data driven evidential belief function model to predict groundwater potential zonation. J. Hydrol. 2014, 513, 283–300. [Google Scholar] [CrossRef]
  32. Hutchison, C.S.; Tan, D.N.K. Geology of Peninsular Malaysia; Published jointly by the University of Malaya [and] the Geological Society of Malaysia: Kuala Lumpur, Malaysia, 2009. [Google Scholar]
  33. Shamsuddin, M.K.N.; Sulaiman, W.N.A.; Suratman, S.; Zakaria, M.P.; Samuding, K. Conjunctive use of surface water and groundwater via the bank infiltration method. Arab. J. Geosci. 2014, 7, 3731–3753. [Google Scholar] [CrossRef]
  34. The Study on the Sustainable Groundwater Resources and Environmental Management for the Langat Basin in Malaysia. Available online: https://openjicareport.jica.go.jp/pdf/11684388.pdf (accessed on 21 May 2021).
  35. Memarian, H.; Balasundram, S.K. Hydrological Trend Analysis Integrated with Landscape Analysis at the Watershed Scale (Case Study: Langat Basin, Malaysia). Landsc. Ecol. Influ. Land Use Anthropog. Impacts Landscape Creat. 2016. [Google Scholar] [CrossRef] [Green Version]
  36. APHA. Standard Methods for the Examination of Water and Wastewater, 22nd ed.; American Water Works Association, Water Environment Federation: Washington, DC, USA, 2010. [Google Scholar]
  37. Chidambaram, S.; Karmegam, U.; Prasanna, M.V.; Sasidhar, P. A study on evaluation of probable sources of heavy metal pollution in groundwater of Kalpakkam region, South India. Environmentalist 2012, 32, 371–382. [Google Scholar] [CrossRef]
  38. Thirumalini, S.; Joseph, K. Correlation between electrical conductivity and total dissolved solids in natural waters. Malays. J. Sci. 2009, 28, 55–61. [Google Scholar] [CrossRef]
  39. Huang, G.; Zhang, M.; Liu, C.; Li, L.; Chen, Z. Heavy metal (loid) s and organic contaminants in groundwater in the Pearl River Delta that has undergone three decades of urbanization and industrialization: Distributions, sources, and driving forces. Sci. Total Environ. 2018, 635, 913–925. [Google Scholar] [CrossRef]
  40. Selvakumar, S.; Ramkumar, K.; Chandrasekar, N.; Magesh, N.S.; Kaliraj, S. Groundwater quality and its suitability for drinking and irrigational use in the Southern Tiruchirappalli district, Tamil Nadu, India. Appl. Water Sci. 2017, 7, 411–420. [Google Scholar] [CrossRef] [Green Version]
  41. Zhang, B.; Song, X.; Zhang, Y.; Han, D.; Tang, C. Hydrochemical characteristics and water quality assessment of surface water and groundwater in Songnen plain, Northeast China. Water Res. 2012, 46, 2737–2748. [Google Scholar] [CrossRef] [PubMed]
  42. Zhu, B.; Wang, X.; Rioual, P. Multivariate indications between environment and ground water recharge in a sedimentary drainage basin in northwestern China. J. Hydrol. 2017, 549, 92–113. [Google Scholar] [CrossRef]
  43. Wood, M.D.; Beresford, N.A.; Copplestone, D. Limit of detection values in data analysis: Do they matter? Radioprotection 2011, 46, S85–S90. [Google Scholar] [CrossRef] [Green Version]
  44. Annapoorna, H.; Janardhana, M.R. Assessment of groundwater quality for drinking purpose in rural areas surrounding a defunct copper mine. Aquat. Procedia 2015, 4, 685–692. [Google Scholar] [CrossRef]
  45. Ravikumar, P.; Venkatesharaju, K.; Somashekar, R.K. Major ion chemistry and hydrochemical studies of groundwater of Bangalore South Taluk, India. Environ. Monit. Assess. 2010, 163, 643–653. [Google Scholar] [CrossRef] [PubMed]
  46. Piper, A.M. A graphic procedure in the geochemical interpretation of water-analyses. Eos Trans. Am. Geophys. Union 1944, 25, 914–928. [Google Scholar] [CrossRef]
  47. Kura, N.U.; Ramli, M.F.; Sulaiman, W.N.A.; Ibrahim, S.; Aris, A.Z. An overview of groundwater chemistry studies in Malaysia. Environ. Sci. Pollut. Res. 2018, 25, 7231–7249. [Google Scholar] [CrossRef] [PubMed]
  48. Souid, F.; Agoubi, B.; Telahigue, F.; Chahlaoui, A.; Kharroubi, A. Groundwater salinization and seawater intrusion tracing based on Lithium concentration in the shallow aquifer of Jerba Island, southeastern Tunisia. J. Afr. Earth Sci. 2018, 138, 233–246. [Google Scholar] [CrossRef]
  49. Masoud, A.A.; El-Horiny, M.M.; Atwia, M.G.; Gemail, K.S.; Koike, K. Assessment of groundwater and soil quality degradation using multivariate and geostatistical analyses, Dakhla Oasis, Egypt. J. Afr. Earth Sci. 2018, 142, 64–81. [Google Scholar] [CrossRef]
  50. Voutsis, N.; Kelepertzis, E.; Tziritis, E.; Kelepertsis, A. Assessing the hydrogeochemistry of groundwaters in ophiolite areas of Euboea Island, Greece, using multivariate statistical methods. J. Geochem. Explor. 2015, 159, 79–92. [Google Scholar] [CrossRef]
  51. Lezzaik, K.; Milewski, A.; Mullen, J. The groundwater risk index: Development and application in the Middle East and North Africa region. Sci. Total Environ. 2018, 628, 1149–1164. [Google Scholar] [CrossRef]
  52. Selvakumar, S.; Chandrasekar, N.; Kumar, G. Hydrogeochemical characteristics and groundwater contamination in the rapid urban development areas of Coimbatore, India. Water Res Ind. 2017, 17, 26–33. [Google Scholar] [CrossRef]
  53. Signes-Pastor, A.; Burló, F.; Mitra, K.; Carbonell-Barrachina, A.A. Arsenic biogeochemistry as affected by phosphorus fertilizer addition, redox potential and pH in a west Bengal (India) soil. Geoderma 2007, 137, 504–510. [Google Scholar] [CrossRef]
  54. Isa, N.M.; Aris, A.Z.; Sulaiman, W.N.A. Extent and severity of groundwater contamination based on hydrochemistry mechanism of sandy tropical coastal aquifer. Sci. Total Environ. 2012, 438, 414–425. [Google Scholar] [CrossRef]
  55. Abd Manap, M.; Sulaiman, W.N.A.; Ramli, M.F.; Pradhan, B.; Surip, N. A knowledge-driven GIS modeling technique for groundwater potential mapping at the Upper Langat Basin, Malaysia. Arab. J. Geosci. 2013, 6, 1621–1637. [Google Scholar] [CrossRef]
  56. Chenini, I.; Farhat, B.; Mammou, A.B.; Chenini, I.; Farhat, B.; Mammou, A.B. Identification of major sources controlling groundwater chemistry from a multilayered aquifer system Identification of major sources controlling groundwater chemistry from a multilayered aquifer system. Chem. Speciat. Bioavailab. 2015, 22, 183–189. [Google Scholar] [CrossRef]
  57. Lim, W.Y.; Aris, A.Z.; Zakaria, M.P. Spatial variability of metals in surface water and sediment in the Langat river and geochemical factors that influence their water-sediment interactions. Sci. World J. 2012. [Google Scholar] [CrossRef] [Green Version]
  58. Sefie, A.; Aris, A.Z.; Ramli, M.F.; Narany, T.S.; Shamsuddin, M.K.N.; Saadudin, S.B.; Zali, M.A. Hydrogeochemistry and groundwater quality assessment of the multilayered aquifer in Lower Kelantan Basin, Kelantan, Malaysia. Environ. Earth Sci. 2018, 77, 1–15. [Google Scholar] [CrossRef] [Green Version]
  59. Kamal, Z.A.; Sulaiman, M.S.; Hakim, M.K.; Syahira, A.; Hamzah, Z.; Khan, M.M.A. Investigation of Seawater Intrusion in Coastal Aquifers of Kelantan, Malaysia using Geophysical and Hydrochemical Techniques. In IOP Conference Series: Earth and Environmental Science; IOP Publishing: Kelantan Malaysia, 2020; Volume 549, p. 012018. Available online: https://iopscience.iop.org/article/10.1088/1755-1315/549/1/012018/meta (accessed on 21 May 2021).
  60. Singh, K.C.; Kumar, A.A.; Shashtri, S.; Kumar, A.A.; Kumar, P.; Mallick, J. Multivariate statistical analysis and geochemical modeling for geochemical assessment of groundwater of Delhi, India. J. Geochem. Explor. 2017, 175, 59–71. [Google Scholar] [CrossRef]
  61. WHO. (2017); Guidelines for Drinking-Water Quality: Fourth Edition Incorporating the First Addendum; World Health Organization: Geneva, Switzerlands; Available online: apps.who.int/iris/bitstream/handle/10665/254637/9789241549950-eng.pdf (accessed on 8 August 2020).
  62. MOH. Drinking and Raw Water Quality Standard. Engineering Services Division Malaysia. 2016. Available online: environment.com.my/wp-content/uploads/2016/05/Drinking-Water-MOH.pdf (accessed on 8 August 2020).
  63. Zereg, S.; Boudoukha, A.; Benaabidate, L. Impacts of natural conditions and anthropogenic activities on groundwater quality in Tebessa plain, Algeria. Sustain. Environ. Res. 2018, 28, 340–349. [Google Scholar] [CrossRef]
  64. Yang, L.; Zhu, G.; Shi, P.; Li, J.; Liu, Y.; Tong, H.; Zhang, Y. Spatiotemporal characteristics of hydrochemistry in Asian arid inland basin–a case study of Shiyang River Basin. Environ. Sci. Pollut. Res. 2018, 25, 2293–2302. [Google Scholar] [CrossRef]
  65. Keesari, T.; Sharma, D.A.; Rishi, M.S.; Pant, D.; Mohokar, H.V.; Jaryal, A.K.; Sinha, U.K. Isotope investigation on groundwater recharge and dynamics in shallow and deep alluvial aquifers of southwest Punjab. Appl. Radiat. Isot. 2017, 129, 163–170. [Google Scholar] [CrossRef]
  66. Ramachandran, A.; Krishnamurthy, R.R.; Jayaprakash, M.; Shanmugasundharam, A. Environmental impact assessment of surface water and groundwater quality due to flood hazard in Adyar River Bank. Acta Ecol. Sin. 2019, 39, 125–132. [Google Scholar] [CrossRef]
  67. González-Fernández, B.; Menéndez-Casares, E.; Meléndez-Asensio, M.; Fernández-Menéndez, S.; Ramos-Muñiz, F.; Cruz-Hernández, P.; González-Quirós, A. Sources of mercury in groundwater and soils of west Gijón (Asturias, NW Spain). Sci. Total Environ. 2014, 481, 217–231. [Google Scholar] [CrossRef]
  68. Wang, L.; Hou, D.; Cao, Y.; Sik, Y.; Tack, F.M.G.; Rinklebe, J.; Connor, D.O. Remediation of mercury contaminated soil, water, and air: A review of emerging materials and innovative technologies. Environ. Int. 2020, 134, 105281. [Google Scholar] [CrossRef] [PubMed]
  69. Andrea, C.; Stefano, C.; Andrea, E.; Elena, P.; Elisa, P.; Asta, G.; Urbanc, J.; Enrico, Z.; Luca, Z. Mercury in the unconfined aquifer of the Isonzo/Soča River alluvial plain downstream from the Idrija mining area. Chemosphere 2018, 195, 749–761. [Google Scholar] [CrossRef]
  70. Abiriga, D.; Vestgarden, L.S.; Klempe, H. Groundwater contamination from a municipal landfill: Effect of age, landfill closure, and season on groundwater chemistry. Sci. Total Environ. 2020, 737, 140307. [Google Scholar] [CrossRef]
  71. Melegy, A.A.; Shaban, A.M.; Hassaan, M.M.; Salman, S.A. Geochemical mobilization of some heavy metals in water resources and their impact on human health in Sohag Governorate, Egypt. Arab. J. Geosci. 2013, 7, 4541–4552. [Google Scholar] [CrossRef]
  72. Tao, Y.; Yuan, Z.; Wei, M.; Xiaona, H. Characterization of heavy metals in water and sediments in Taihu Lake, China. Environ. Monit. Assess. 2012, 184, 4367–4382. [Google Scholar] [CrossRef] [PubMed]
  73. Patil, V.T.; Patil, P.R. Physicochemical analysis of selected groundwater samples of Amalner town in Jalgaon District, Maharashtra, India. Eur. J.Chem. 2010, 7, 111–116. [Google Scholar] [CrossRef] [Green Version]
  74. Ledesma-Ruiz, R.; Mahlknecht, J. Geochemical and Isotopic Characterization of Groundwater in Tecate, Baja California, Mexico. Procedia Earth Planet. Sci. 2017, 17, 516–519. [Google Scholar] [CrossRef]
  75. Sheikhy Narany, T.; Ramli, M.F.; Aris, A.Z.; Nor, W.; Sulaiman, A.; Juahir, H.; Fakharian, K. Identification of the Hydrogeochemical Processes in Groundwater Using Classic Integrated Geochemical Methods and Geostatistical Techniques, in Amol-Babol Plain, Iran. Sci. World J. 2014, 1–15. [Google Scholar] [CrossRef] [PubMed]
  76. Varughese, S.; Devi Prasad, K.V. Physico-chemical analysis of groundwater samples in the Varahanadi watershed, India. Agris Line Papers Econ. Inform. 2012, 2, 1662–1669. [Google Scholar] [CrossRef]
  77. Rezaei, A.; Hassani, H.; Jabbari, N. Evaluation of groundwater quality and assessment of pollution indices for heavy metals in North of Isfahan Province, Iran. Sustain. Water Resour. Manag. 2017, 5, 491–512. [Google Scholar] [CrossRef]
  78. Tirkey, P.; Bhattacharya, T.; Chakraborty, S.; Baraik, S. Groundwater for Sustainable Development Assessment of groundwater quality and associated health risks: A case study of Ranchi city, Jharkhand, India. Groundw. Sustain. Dev. 2017, 5, 85–100. [Google Scholar] [CrossRef]
  79. Kumar, P.S.; Delson, P.D.; Babu, P.T. Appraisal of heavy metals in groundwater in Chennai city using a HPI model. Bull. Environ. Contam. Toxicol. 2012, 89, 793–798. [Google Scholar] [CrossRef] [PubMed]
  80. Wongsasuluk, P.; Chotpantarat, S.; Siriwong, W.; Robson, M. Heavy metal contamination and human health risk assessment in drinking water from shallow groundwater wells in an agricultural area in Ubon Ratchathani province, Thailand. Environ. Geochem. Health 2014, 36, 169–182. [Google Scholar] [CrossRef] [PubMed]
  81. Hepburn, E.; Northway, A.; Bekele, D.; Liu, G.; Currell, M. A method for separation of heavy metal sources in urban groundwater using multiple lines of evidence. Environ. Pollut. 2018, 241, 787–799. [Google Scholar] [CrossRef]
  82. Kura, N.U.; Ramli, M.F.; Sulaiman, W.N.A.; Ibrahim, S.; Aris, A.Z.; Mustapha, A. Evaluation of factors influencing the groundwater chemistry in a small tropical island of Malaysia. Int. J. Environ. Res. Public Health 2013, 10, 1861–1881. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  83. Sefie, A.; Aris, A.Z.; Shamsuddin, M.K.N.; Tawnie, I.; Suratman, S.; Idris, A.N.; BahrenSaadudin, S.; Wan Ahmad, W.K. Hydrogeochemistry of Groundwater from Different Aquifer in Lower Kelantan Basin, Kelantan, Malaysia. Procedia Environ. Sci. 2015, 30, 151–156. [Google Scholar] [CrossRef] [Green Version]
  84. Mrazovac, S.; Vojinović-Miloradov, M. Correlation of main physicochemical parameters of some groundwater in northern Serbia. J. Geochem. Explor. 2011, 108, 176–182. [Google Scholar] [CrossRef]
  85. Gibbs, R.J. Mechanism controlling world water chemistry. Science 1970, 170, 1088–1090. [Google Scholar] [CrossRef] [PubMed]
  86. Gulgundi, M.S.; Shetty, A. Groundwater quality assessment of urban Bengaluru using multivariate statistical techniques. Appl. Water Sci. 2018, 8, 43. [Google Scholar] [CrossRef] [Green Version]
  87. Adelopo, A.O.; Haris, P.I.; Alo, B.I.; Huddersman, K.; Jenkins, R.O. Multivariate analysis of the effects of age, particle size and landfill depth on heavy metals pollution content of closed and active landfill precursors. Waste Manag. 2018, 78, 227–237. [Google Scholar] [CrossRef]
  88. Kumar, P.J.S.; James, E.J. Physicoche mical parameters and their sources in groundwater in the Thirupathur region, Tamil Nadu, South India. Appl. Water Sci. 2013, 3, 219–228. [Google Scholar] [CrossRef] [Green Version]
  89. Khan, M.N.; Mobin, M.; Abbas, Z.K.; Arabia, S. Fertilizers and Their Contaminants in Soils, Surface and Groundwater. Encycl. Anthr. 2018, 5, 225–240. [Google Scholar]
  90. Dash, A.; Das, H.K.; Mishra, B. Hydrogeochemistry and ground water quality in and around Joda of Keonjhar District, Odisha, India. Int. J. Innov. Sci. Res. 2014, 12, 409–419. [Google Scholar]
  91. Zghibi, A.; Merzougui, A.; Zouhri, L.; Tarhouni, J. Journal of African Earth Sciences Understanding groundwater chemistry using multivariate statistics techniques to the study of contamination in the Korba unconfined aquifer system of Cap-Bon (North-east of Tunisia). J. Afr. Earth Sci. 2014, 89, 1–15. [Google Scholar] [CrossRef]
  92. Κίρλας, Μ.Χ. Simulation of Groundwater Flow Using the MODFLOW Code in the Alluvial Aquifer of Korisos Basin, NW Greece. Available online: https://www.researchgate.net/publication/321012204_Simulation_of_groundwater_flow_using_the_MODFLOW_code_in_the_alluvial_aquifer_of_Korisos_basin_NW_Greece (accessed on 21 May 2021).
Figure 1. The land use map of the Langat basin.
Figure 1. The land use map of the Langat basin.
Ijerph 18 05733 g001
Figure 2. Piper trilinear diagram showing hydrogeochemical facies. Na-HCO3 water type (Circle I) and Na-Cl water type (circle II).
Figure 2. Piper trilinear diagram showing hydrogeochemical facies. Na-HCO3 water type (Circle I) and Na-Cl water type (circle II).
Ijerph 18 05733 g002
Figure 3. The Gibbs diagram showing the mechanism governing groundwater chemistry.
Figure 3. The Gibbs diagram showing the mechanism governing groundwater chemistry.
Ijerph 18 05733 g003
Figure 4. Scree plot for PCA.
Figure 4. Scree plot for PCA.
Ijerph 18 05733 g004
Figure 5. Rotated component of PCA.
Figure 5. Rotated component of PCA.
Ijerph 18 05733 g005
Figure 6. Classification of the sampling stations based on HCA outputs.
Figure 6. Classification of the sampling stations based on HCA outputs.
Ijerph 18 05733 g006
Table 1. Summary of inland groundwater contamination studies in Malaysia.
Table 1. Summary of inland groundwater contamination studies in Malaysia.
Study AreaMethodStudied ElementsReference
North of Kuala Lumpur, Kinta Valley, Perak and Alor Setar, KedahHydrochemistry analysisMajor ions[12]
Disposal site in Seri Petaling, Selangor2D electrical resistivity, geochemistry, and Analysis of variance (ANOVA)Resistivity image, in situ parameters, major ions and trace elements[13]
Disposal site in Taiping PerakHydrochemistry analysis, surfer softwareSoil samples, heavy metals[14]
Langat Basin, Selangor2D resistivity measurement, MODFLOW (modular finite-difference flow model), and SWOT (Strengths, Weaknesses, Opportunities, and Threats) analysisIn situ parameters, major ions, and heavy metals[8]
Ampar Tenang landfill, SelangorSodium adsorption ratio (SAR), piper diagram, 2D resistivity techniqueResistivity image and major ions[15]
Rosob Village, SabahHydrochemistry analysisHeavy metals[16]
Ampar Tenang and Bukit Tagar landfill, SelangorHydrochemistry analysisMajor ions, trace elements, and heavy metals[17]
North Kelantan2D resistivity measurement, hydrochemistry, and soil particle size analysisResistivity image, soil samples, major ions[18]
Ampar Tenang landfill, SelangorPhysiochemical and biochemical analysisPhysiochemical parameters, organic contaminants, and heavy metals[19]
North of Gemas, Negeri Sembilan2D electrical resistivity measurement, induced polarization, and borehole geophysical techniquesResistivity images, pumping test data, and rock and soil data[20]
Melaka stateDRASTIC model (Depth to water, Recharge, Aquifer media, Soil media, Topography, Impact of the vadose zone, Hydraulic conductivity) with GIS and remote sensingGroundwater level, recharge, lithology, soil type, topography, hydraulic conductivity, and land use data[21]
Southwest state of Selangor within the Langat BasinBank infiltration (BI), pumping test, 2D resistivity survey, soil sieve analysesResistivity images, isotope and major ions[22]
Batang Padang, PerakGIS-based optimized DRASTIC model and analytic Process (AHP)Borehole data, average annual rainfall, geophysical data, soil map, remote sensing imagery, and geophysical data[23]
Ex-landfill Taman Beringin, SelangorHydrochemical analysis, physicochemical analysis, and water quality analysisPhysicochemical parameters, heavy metals, NH3-N, Cl, F, Pb, Ni, and Fe[24]
Semenyih and Kajang, SelangorGeological analysis, hydrochemical analysis, piper diagram, and well water chemistry interpretationMajor ions, physicochemical parameters,[25]
Langat BasinHydrochemical analysis, piper diagram, multivariate analysisPhysicochemical parameters, major ions, and heavy metalsCurrent study
Table 2. The geological profile setting of the Langat Basin [34].
Table 2. The geological profile setting of the Langat Basin [34].
A.s.l (m)Geological Setting
>30acid intrusives (undifferentiated)
>20Phyllite, schist, and slate; limestone and sandstone
>10Peat, humic clay, and silt; clay, silt, sand, and gravel
>1Clay and silt
A.s.l, average sea level.
Table 3. The description of hydrogeological and hydrochemical properties of the Langat Basin [34].
Table 3. The description of hydrogeological and hydrochemical properties of the Langat Basin [34].
HydrologyMean
Temperature27 °C
Annual precipitation2200 mm
Annual evapotranspiration1284 mm
Groundwater recharge rate108 mm
Groundwater discharge rate846 mm
Transmissivity0.024 m2/s
Vertical hydraulic conductivity/permeability7 × 10−9 m/s
Aquifer thickness10–100 m
Sustainable pumping rate26,849 million liter per day (MLD)
Water typeCa-Mg-Cl [15]
Na-Cl (current study)
MLD: million liters/day.
Table 4. Site description of the study areas.
Table 4. Site description of the study areas.
StationsA.s.lCoordinateWater TableDepth of BoreholeSite Description
mNEmm
LW1303.00705101.7735.3511.0Residential area
LW2473.00409101.8731.00NAResidential area and near to a palm oil plantation
LW3502.88834101.8863.50NAResidential area
LW4202.89599101.7743.1245.0Near to a river and a shrub area
LW5362.85851101.7322.9122.7Residential area
LW6262.86136101.5574.9613.0Residential area and near to a river
LW7112.87883101.6214.2311.7Wetland and near to a palm oil plantation
LW842.82795101.5463.4249.5Part of agricultural activities
LW962.78176101.5274.58NANear to a l palm oil plantation and a lake, and part of agricultural activities
LW1052.73455101.4722.0065.0Residential area, near to a coastal area and agricultural activities
LW11102.81993101.6393.715.8Residential area, near to a palm oil plantation and farming activities
LW1282.83261101.6058.7516.0Residential area, and near to industrial activities
LW13112.81055101.6028.87NANear to industrial areas and a palm oil plantation
LW1472.79758101.5590.83NAResidential area, near to a palm oil plantation and a construction site
LW15112.87069101.6762.9318.0Residential area
A.s.l., average sea level. NA, not available from the database. Borehole screening, 4.00−10.00 m (current study). Clay covering, 1–3 m [33].
Table 5. Statistical summary of the physiochemical and heavy metal parameters in the groundwater of the Langat Basin.
Table 5. Statistical summary of the physiochemical and heavy metal parameters in the groundwater of the Langat Basin.
ParametersUnitMean (SD)WHOMOH
pH 6.13 ± 0.896.5–8.56.5–9.0
Temperature°C29.64 ± 0.90--
DOmg/L1.25 ± 0.35--
Salinityppt1.14 ± 2.22--
ECµS/cm2286.38 ± 4318.75500-
TDSmg/L1352.58 ± 2534.345001000
HCO3mg/L185.93 ± 241.87500-
Clmg/L74.64 ± 86.77250250
SO42−mg/L38.6 ± 58.22250250
Ca2+mg/L14.58 ± 22.0175-
Mg2+mg/L6.94 ± 6.7450150
K+mg/L12.85 ± 13.87--
Na+mg/L24.41 ± 19.64200200
Femg/L6.035 ± 9.027NA0.3
Mnmg/L0.378 ± 0.600NA0.1
Asmg/L0.01 ± 0.0190.010.01
Cumg/L0.002 ± 0.00221
Pbmg/L0.005 ± 0.0020.010.01
Znmg/L0.023 ± 0.024NA3
Nimg/L0.003 ± 0.0010.070.02
Cdmg/L0.001 ± 0.0000.0030.003
Semg/L0.001 ± 0.0010.040.01
Crmg/L0.001 ± 0.0020.050.05
Hgmg/L0.010 ± 0.0130.00060.001
SD, standard deviation; WHO, World Health Organization; MOH, Ministry of Health Malaysia. NA, not available.
Table 6. Pearson’s product moment correlation of the physicochemical parameters and major ions.
Table 6. Pearson’s product moment correlation of the physicochemical parameters and major ions.
pHTempSalCondDOTDSHCO3ClCa2+Mg2+K+Na+SO42−
pH1−0.0550.1910.2010.1270.2060.429 **0.398 **0.0130.0410.0520.1030.261
Temp 10.306 *0.307 *−0.0100.302 *−0.047−0.0610.1150.2350.2100.1990.056
Sal 11.000 **0.1001.000 **0.625 **0.2660.1790.2560.2180.2440.018
Cond 10.1111.000 **0.631 **0.2720.1840.2650.2280.2530.021
DO 10.110−0.155−0.2130.0740.2350.2050.149−0.126
TDS 10.641 **0.2810.1860.2690.2320.2560.026
HCO3 10.761 **0.1610.2160.2290.2240.342 *
Cl 1−0.0260.0040.0320.0480.544 **
Ca2+ 10.688 **0.692 **0.689 **0.165
Mg2+ 10.981 **0.915 **0.097
K+ 10.930 **0.131
Na+ 10.018
SO42− 1
** Correlation is significant at the 0.01 level (2-tailed). * Correlation is significant at the 0.05 level (2-tailed).
Table 7. Principal component loading of the measured variables.
Table 7. Principal component loading of the measured variables.
ParametersPC1PC2PC3PC4
K+0.9580.1120.0410.024
Mg+0.9400.1050.0760.139
Na+0.9290.1470.0220.026
Ca+0.8140.0600.057−0.091
Salinity0.1110.9810.0970.011
EC0.1200.9800.1020.022
TDS0.1230.9790.1110.026
Cl−0.0370.2120.8820.038
SO42−0.146−0.1020.745−0.100
HCO30.1050.5710.7140.096
DO0.2150.121−0.3850.734
pH level0.0420.1570.5100.576
Temperature0.2340.373−0.178−0.482
Eigenvalue3.5053.4882.3261.154
Total variance26.96526.83117.8918.880
Total cumulative26.96553.79671.68680.566
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Zainol, N.F.M.; Zainuddin, A.H.; Looi, L.J.; Aris, A.Z.; Isa, N.M.; Sefie, A.; Ku Yusof, K.M.K. Spatial Analysis of Groundwater Hydrochemistry through Integrated Multivariate Analysis: A Case Study in the Urbanized Langat Basin, Malaysia. Int. J. Environ. Res. Public Health 2021, 18, 5733. https://doi.org/10.3390/ijerph18115733

AMA Style

Zainol NFM, Zainuddin AH, Looi LJ, Aris AZ, Isa NM, Sefie A, Ku Yusof KMK. Spatial Analysis of Groundwater Hydrochemistry through Integrated Multivariate Analysis: A Case Study in the Urbanized Langat Basin, Malaysia. International Journal of Environmental Research and Public Health. 2021; 18(11):5733. https://doi.org/10.3390/ijerph18115733

Chicago/Turabian Style

Zainol, Nur Fatihah Mohamad, Azim Haziq Zainuddin, Ley Juen Looi, Ahmad Zaharin Aris, Noorain Mohd Isa, Anuar Sefie, and Ku Mohd Kalkausar Ku Yusof. 2021. "Spatial Analysis of Groundwater Hydrochemistry through Integrated Multivariate Analysis: A Case Study in the Urbanized Langat Basin, Malaysia" International Journal of Environmental Research and Public Health 18, no. 11: 5733. https://doi.org/10.3390/ijerph18115733

APA Style

Zainol, N. F. M., Zainuddin, A. H., Looi, L. J., Aris, A. Z., Isa, N. M., Sefie, A., & Ku Yusof, K. M. K. (2021). Spatial Analysis of Groundwater Hydrochemistry through Integrated Multivariate Analysis: A Case Study in the Urbanized Langat Basin, Malaysia. International Journal of Environmental Research and Public Health, 18(11), 5733. https://doi.org/10.3390/ijerph18115733

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop