Efficient Catalytic Dehydration of High-Concentration 1-Butanol with Zn-Mn-Co Modified γ-Al2O3 in Jet Fuel Production
by
,
Jing Wu
1
,
Hong-Juan Liu
1,
Xiang Yan
1,
Yu-Jie Zhou
1,
Zhang-Nan Lin
1,
Shuo Mi
1,
Ke-Ke Cheng
2,* and
Jian-An Zhang
1,* 1
Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084, China
2
School of Chemical Engineering and Energy Technology, Dongguan University of Technology, Dongguan 523808, China
*
Authors to whom correspondence should be addressed.
Catalysts 2019, 9(1), 93; https://doi.org/10.3390/catal9010093
Submission received: 14 November 2018
/
Revised: 8 January 2019
/
Accepted: 11 January 2019
/
Published: 16 January 2019
(This article belongs to the Special Issue Catalysis for Energy Production)
Abstract
:It is important to develop full-performance bio-jet fuel based on alternative feedstocks. The compound 1-butanol can be transformed into jet fuel through dehydration, oligomerization, and hydrogenation. In this study, a new catalyst consisting of Zn-Mn-Co modified γ-Al2O3 was used for the dehydration of high-concentration 1-butanol to butenes. The interactive effects of reaction temperature and butanol weight-hourly space velocity (WHSV) on butene yield were investigated with response surface methodology (RSM). Butene yield was enhanced when the temperature increased from 350 °C to 450 °C but it was reduced as WHSV increased from 1 h−1 to 4 h−1. Under the optimized conditions of 1.67 h−1 WHSV and 375 °C reaction temperature, the selectivity of butenes achieved 90%, and the conversion rate of 1-butanol reached 100%, which were 10% and 6% higher, respectively, than when using unmodified γ-Al2O3. The Zn-Mn-Co modified γ-Al2O3 exhibited high stability and a long lifetime of 180 h, while the unmodified γ-Al2O3 began to deactivate after 60 h. Characterization with X-ray diffraction (XRD), nitrogen adsorption-desorption, pyridine temperature-programmed desorption (Py-TPD), pyridine adsorption IR spectra, and inductively coupled plasma atomic emission spectrometry (ICP-AES), showed that the crystallinity and acid content of γ-Al2O3 were obviously enhanced by the modification with Zn-Mn-Co, and the loading amounts of zinc, manganese, and cobalt were 0.54%, 0.44%, and 0.23%, respectively. This study provides a new catalyst, and the results will be helpful for the further optimization of bio-jet fuel production with a high concentration of 1-butanol.
1. Introduction
Recently, the consumption of jet fuel has been increasing due to the development of the aviation industry, which has resulted in many environmental problems and energy security issues. Therefore, developing full-performance bio-jet fuel based on alternative feedstocks is urgent. The compound 1-butanol can be transformed into jet fuel through dehydration, oligomerization, and hydrogenation [1,2]. Efficient catalytic dehydration of 1-buanol to butenes is the first step and an important guarantee for further processing.
Considerable researches have focused on the conversion of sugars obtained from biomass to 1-butanol, where sugars can be fermented to ‘acetone-butanol-ethanol’ (ABE) using Clostridium acetobutylicum or Clostridium beijerinckii [3,4]. Fermented 1-butanol can be separated from the fermentation broth by techniques such as gas-stripping, distillation, membrane separation, and extraction. Generally, fermented 1-butanol is separated into an aqueous phase with 7.7 wt % 1-butanol and an organic phase including 79.9 wt % bio-butanol and 20.1 wt % water at 20 °C. Lin et al. used fed-batch fermentation coupled with gas-stripping for 1-butanol production, and an aqueous phase (84.64 g/L 1-butanol) and an organic phase (624 g/L 1-butanol) were obtained [5]. Xue et al. developed a two-stage gas-stripping technology coupled with 1-butanol fermentation, and the concentrations of 1-butanol in the organic phase and aqueous phase were 612.3–623.3 g/L and 91.3–101.3 g/L, respectively; the aqueous phase was heated and gas-stripped again to concentrate 1-butanol [6,7]. Some researches focusing on the dehydration of low-concentration 1-butanol [8] and pure 1-butanol [9,10] have been reported. However, using a high-concentration 1-butanol solution as feedstock seems more economical than using low-concentration 1-butanol or pure 1-butanol, because low-concentration 1-butanol leads to low productivity of butene and the pure 1-butanol needs to be separated further. Unfortunately, the dehydration of high-concentration 1-butanol solutions is seldom studied.
γ-Al2O3 and zeolites show high activity in the alcohol catalytic dehydration reaction. Zeolites with 10-ring unidirectional channels such as Theta-1 and ZSM-23 can efficiently catalyze butanol to butenes, but by-products would be produced such as propylene and C5 olefins [11]. When using γ-Al2O3 as a catalyst, the composition of the products is relatively easier to control, and the product distribution depends on the process temperature and strength of catalyst acidity [12,13]. It has been proven that there is more dibutylether than butenes in the products when the reaction temperature is below 310 °C, and, as the temperature rises, butenes supersede dibutylether [14]. Transition metal catalysts such as cobalt [15,16], manganese, iron [17], nickel [18], and zinc oxides [19] are often utilized for the alcohol dehydration reaction. Metal-loaded catalysts with high catalytic activity and low cost are more adaptable to industrialization requirements. Osman reported that Cu/γ-Al2O3 showed a high degree of activity and stability in a catalytic methanol dehydration reaction [20]. Said used phosphotungstic acid-supported γ-Al2O3 to catalyze the dehydration of ethanol to diethyl ether. The results indicated that the catalytic performance of supported catalysts was correlated with the strong and intermediate Brønsted acid sites due to the presence of Keggin structure and tungsten oxide [21].
In this study, Zn-Mn-Co modified γ-Al2O3 was prepared, and the catalytic performance of 1-butanol dehydration to butenes was investigated with 620 g/L 1-butanol as the raw material. This concentration of raw material is more consistent with the concentration range of bio-butanol separated from the fermentation broth. The experiments were designed by the central composite design method for optimizing the dehydration process of 1-butanol with respect to temperature (350–450 °C) and WHSV (1.0–4.0) and maximizing butene yield. This study provides a new catalyst, and the results have great significance for the goal of reducing the production cost of bio-jet fuel from 1-butanol.
2. Results and Discussion
2.1. Catalyst Characterization
The XRD pattern of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3 are shown in Figure 1. The position of the diffraction peaks of the modified sample was well matched with that of the original sample, which indicated the modification of Zn-Mn-Co had no effects on the crystalline phase of γ-Al2O3. The intensity of the diffraction peaks became stronger, which suggested that the crystallinity of Zn-Mn-Co modified γ-Al2O3 was higher than that of γ-Al2O3. The improvement of crystallinity may be attributed to the fact that zinc, manganese, and cobalt formed a spinel solid solution with γ-Al2O3, which improved the stability of the catalyst in the reaction environment with water [22]. Zinc, manganese, and cobalt oxides were not detected in the spectra, showing that zinc, manganese, and cobalt were highly dispersed on the catalyst surface. Research has suggested that manganese ions play an important role in improving the dispersion of other metal ions [23]. To verify whether metal ions were loaded onto γ-Al2O3, the metal loadings of the modified catalyst were measured by the inductively coupled plasma atomic emission spectrometry (ICP-AES) method, and the loading amounts of zinc, manganese, and cobalt were 0.54%, 0.44%, and 0.23%, respectively.
Figure 2 shows the nitrogen adsorption–desorption isotherms at liquid nitrogen temperature (77 K) for γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3 samples. Both of the isotherms belong to type IV, and the close hysteresis loops were classified as H3 [24]. The specific surface areas, average pore size, and total pore volume of the catalysts are presented in Table 1. The specific surface area of Zn-Mn-Co/γ-Al2O3 was smaller than that of γ-Al2O3, and the total pore volume was reduced by 15% after modification. However, the average pore radius had a slight increase. This may be due to the modification of the metal ions: some of the micropores were blocked. Figure 3 shows the pore size distribution and cumulative pore volume obtained for the catalysts. The pore sizes of both catalysts were mainly distributed in the range of 5–20 nm. The number of micropores in the modified catalyst was less than that in the original sample, which further proved that the modification of metal ions blocked some of the micropores.
The catalytic efficiency of the catalyst is intensively affected by the surface acid sites [8]. In general, most Lewis acids react with water before reacting with the substrate in the presence of water, which results in the deactivation of the catalyst. However, it has been well established that surface Lewis acid sites of alumina catalyze the dehydration of alcohols. Phung et al. reported that the activity of alumina was observed in the dehydration of ethanol (in which water is a reaction product) because of its high surface acidity. Lewis acidity does not require dehydroxylation if the basic substrates can displace water. Substrates that have sufficient basicity to compete with water can also be activated by alumina in the presence of water [14,25].
The pyridine temperature-programmed desorption (Py-TPD) profiles of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3 are shown in Figure 4. The desorption peak at 200 °C was enhanced after modification, which proved that there were more weak acid sites on Zn-Mn-Co modified γ-Al2O3. A weak desorption peak appeared at 390 °C, indicating the increase of strong acid sites. The surface acidity values of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3 were quantified by pyridine adsorption IR spectra (Figure 5 and Table 2). The bands distinguished at 1620 cm−1 were assigned to pyridine coordinated to tetrahedral and octahedral Al3+. The area of the 19b band at 1451 cm−1 was used to quantify the total amount of Lewis acid sites (LAS) using its molar adsorption coefficient (ε = 1.5 cm/μmol) [10,26,27,28]. The amount of LAS is given in Table 3. The acidic concentration of total acidity and the strong LAS were measured at 200 °C and 300 °C, respectively. After being modified by zinc, manganese, and cobalt, the total acid content of the catalyst increased by about 10.5%.
2.2. Catalytic Activity of γ-Al2O3 and Zn-Mn-Co/γ-Al2O3
The catalytic activity of γ-Al2O3 and Zn-Mn-Co/γ-Al2O3 was investigated at different reaction temperatures (Table 3 and Table 4) and WSHV (Table 5 and Table 6), with a reaction time of 6 h. The higher reaction temperature had positive effects on the conversion of 1-butanol and the selectivity of butenes, but a too high reaction temperature worked against the selectivity of butenes. The conversion rates of 1-butanol were 71.21% and 82.63% when the reaction temperature was 300 °C and 350 °C, respectively, with γ-Al2O3 as a catalyst, and increased by 12.82% and 15.27% when Zn-Mn-Co/γ-Al2O3 was employed. When the reaction temperature increased from 300 °C to 450 °C, the selectivity of butenes increased to a maximum and then decreased. The highest selectivity of butenes (96.24%) was obtained at the reaction temperature of 400 °C when using Zn-Mn-Co/γ-Al2O3 as the catalyst. A lower reaction temperature led to the formation of dibutyl ether (DBE) and butene, which increased with the increase of the temperature. When the reaction temperature was 450 °C, there was no DBE formation, and some other hydrocarbons such as methane, ethylene, and propylene appeared. Furthermore, the selectivity of butene isomers was strongly influenced by the reaction temperature. More 1-butene was formed at a lower temperature, and higher temperatures led to increased isomerization of 1-butene.
The conversion of 1-butanol dropped rapidly with the increase of WHSV. When the WHSV increased from 1 h−1 to 4 h−1, the conversion rate of 1-butanol decreased from 98.01% to 51.04% with γ-Al2O3 as the catalyst. The same trend was obtained when the reaction was catalyzed by Zn-Mn-Co/γ-Al2O3, and the conversion of 1-butanol was much higher than that when γ-Al2O3 was used as the catalyst. With the increase of WHSV from 1 h−1 to 4 h−1, the proportion of 1-butene in the product increased, and the proportion of butylene isomers decreased. WHSV had little effect on the total selectivity of butenes, which was about 80% and 90% when using γ-Al2O3 and Zn-Mn-Co/γ-Al2O3, respectively.
The catalytic performance of Zn-Mn-Co/γ-Al2O3 was much better than that of γ-Al2O3. The high conversion rate of 1-butanol and the selectivity of butenes indicated that Zn-Mn-Co/γ-Al2O3 exhibited excellent activity at low temperature. Zinc, manganese, and cobalt oxides exhibited high activity in alcohol dehydration, as already proven [15,16,17,29]. The modification of metal ions improved the acidity of the catalyst, and the Lewis acid sites played an important role in the catalytic dehydration of alcohols [30]. A synergistic effect between different metal ions and catalyst carriers improved the catalytic efficiency [23,31].
2.3. Optimization of Temperature and WHSV for Butanol Dehydration
To optimize the temperature and WHSV of the 1-butanol dehydration process, experiments were performed in accordance with the conditions listed in Table 7, which was designed by a central composite design. The values of butene yield (Y) obtained in the 1-butanol dehydration experiments at different temperatures and WHSV are shown in Table 7. The results of ANOVA for a fitted quadratic polynomial model are shown in Table 8. The ‘‘Model F-value” of 642.51 and the lowest p value of less than 0.0001 implied that the model was highly significant and there was only a 0.01% chance that a “Model F-value” this large could occur because of noise. The value of R2 for Y was 0.9978. Butene yield was significantly affected by reaction temperature and WHSV, which could be deduced from the higher absolute value of F and the lower p value (Table 8). The yield of butanol can be predicted by the following equation:
where X1, X2 are the temperature and WHSV, respectively.
Y = −462.49961 + 2.91441X1 − 30.82659X2 + 0.067214 X1X2 − 0.00374651 X12 − 0.66761X22,
X1X2 was significant, suggesting that temperature and WHSV interacted. Figure 6 shows the response surface diagram of temperature and WHSV interactions for the total yield of butenes. Butene yield was enhanced as the temperature increased but reduced as WHSV increased. The temperature and WHSV were optimized by the model with the hypothetical conditions of minimum temperature, maximum WHSV, and maximum butene selectivity. The optimum conditions were found to be 375.78 °C and 1.67 h−1 of WHSV and, under the optimum conditions, the predicted value of total yield of butenes was 92.61%. In a real catalytic reaction of 1-butanol dehydration, the total yield of butenes was 90% at optimum conditions, and the conversion of 1-butanol reached 100%, which were 10% and 6% higher than that when using unmodified γ-Al2O3 in the first 60 h of the reaction. After 60 h of reaction, the unmodified γ-Al2O3 deactivated rapidly, while the Zn-Mn-Co modified γ-Al2O3 showed high stability and long life (Figure 7). Rehydration of γ-Al2O3 is the main reason of deactivation in the presence of water. The rehydration of γ-Al2O3 results in a decrease of the crystallinity of the catalyst and in a significant decrease in the specific surface area of the catalyst [32]. In addition, there is a higher level of by-products of DBE generated with γ-Al2O3 as the catalyst. The DBE may be adsorbed on the surface of the catalyst which leads to the decrease of catalytic efficiency and deactivation of γ-Al2O3. The crystallinity of γ-Al2O3 was enhanced after modification by Zn-Mn-Co (Figure 1), which improves the stability of the catalyst in the reaction environment with water [22]. The enhancement of surface acidity reduces DBE formation, which also prolongs the life of the catalyst.
The application of γ-Al2O3 for the dehydration of 1-butanol has been reported, and the process temperature appeared to play a decisive role in the distribution of olefins and ethers in the products [12]. The proportion of ethers in the product was larger than that of olefin when the reaction temperature was below 300 °C, and olefin superseded ethers with an increasing temperature [13]. The range of reaction temperature in this study was 350–450 °C, and the main products were butenes, which is consistent with the literature. WHSV mainly affected the retention time of 1-butanol in the catalyst micro-reactor system, and high WHSV was not conducive to the adsorption of butanol by a catalyst, which resulted in a decline of the conversion rate of 1-butanol. Zinc, manganese, and cobalt oxides exhibited excellent catalytic activity in the dehydration reaction of alcohol [15,16,17] and they are also used as active components to be loaded onto a catalyst carrier [16,19]. In this study, zinc, manganese, and cobalt were loaded onto γ-Al2O3, and the modified catalyst showed superior catalytic activity, which was attributed to the catalytic ability of the active components and the increase of the catalyst’s acidity. In addition, the enhancement of the crystallinity and acidity of the catalyst made it stable and gave it a long lifetime.
3. Materials and Methods
3.1. Materials
The pseudo-boehmite was provided by the Catalyst Plant of Nankai University, Tianjin, China.
3.2. Catalyst Preparation
The catalysts tested in this study were γ-Al2O3 and Zn-Mn-Co/γ-Al2O3. Pseudo-boehmite was converted to γ-Al2O3 after being calcined at 600 °C for 5 h. One hundred milliliters of a solution containing 1% Zn(NO3)2, 4% Mn(NO3)2, and 3% Co(NO3)2 was added to 10 g γ-Al2O3 with continuous stirring. The resulting solution was placed in an autoclave and treated at 150 °C for 4 h. The treated γ-Al2O3 was washed with distilled water, then dried at 120 °C for 12 h, and calcined at 600 °C in air for 5 h. The resultant powder was molded under 20 MPa pressure to tablets, which were then crushed into particles and sieved to size 20–40 mesh.
3.3. Experimental Design
The interaction effects of reaction temperature and WHSV on 1-butanol dehydration were investigated by response surface methodology (RSM). The experimental scheme in this study was designed by Design-Expert 8.0.5 Trial. The catalytic performance was evaluated using the butene yield. In order to express the effect of factors including reaction temperature and WHSV on the dependent variable (Y), the responses were fitted by the regression model expressed in Equation (2). The optimal point was predicted by a quadratic model, which was expressed as:
where Y is the predicted response, xi and xj are independent variables, b0 is the intercept, bi is the linear coefficient, bii is the quadratic coefficient, and bij is the interaction coefficient.
Y = b0 + ∑bixi + ∑biixi2 + ∑bijxixj
i = 1, 2, …, k; j = 1, 2, …, k; i ≠ j,
i = 1, 2, …, k; j = 1, 2, …, k; i ≠ j,
The experiments were performed in accordance with the conditions listed in Table 7, which were designed by a central composite design. The experimental data were used to calculate the second-order polynomial coefficients, and the model was evaluated by the analysis of variance (ANOVA) technique in the Design-Expert 8.0.5 Trial. The coefficient of determination R2 was used to evaluate the quality of the fit of the polynomial model equation. F-test and t-test were used to check the statistical and regression coefficient significance.
3.4. 1-Butanol Dehydration Experiments
The experiments on the catalytic dehydration of 1-butanol were performed in a micro-reactor device (Figure 8). First, 1.3 g 20–40 mesh catalyst was loaded in the middle of a reactive tube, fixed bed reactor (440 mm length, 8 mm I.D.), and the space under the catalyst bed in the reactor was filled with ceramic chips. The catalyst was pretreated at 450 °C in N2 for 1 h and then cooled to the test temperature. The feed rate of 620 g/L 1-butanol solution was controlled by a micro peristaltic pump, and the 1-butanol was vaporized by a vaporizer.
3.5. Analytical Methods
The analysis of gas phase products was performed on Shimadzu-2010 gas chromatograph (Shimadzu, Kyoto, Japan) equipped with a flame ionization detector (FID), and the components in the product were separated by a capillary column (Alumina/NaSO4, 30 mm × 0.5 mm × 10 um) with nitrogen (pressure 60 kPa) as the carrier gas. The temperatures of the injector and detector were maintained at 150 °C and 250 °C, respectively. The temperature of the column oven was programmed to initially remain at 100 °C for 2 min, then rise to 113 °C at a rate of 10 °C/min, and finally reach 153 °C at a rate of 20 °C/min and remain at that temperature for 2.7 min. The flow rates of hydrogen and air were 40 and 400 mL/min, respectively.
HPLC (Shimadzu LC 20A, Kyoto, Japan) equipped with a refractive index detector and an Aminex HPX-87H column was used to analyze the liquid products. The compound 1-Butanol was analyzed at 65 °C with 5 mM H2SO4 as the mobile phase at 0.8 mL/min.
3.6. Catalyst Characterization
Polymorphs of the catalysts were characterized by an X-ray diffraction system using a D8 Advance instrument (Bruker, Karlsruhe, Germany). The X-ray wavelength was 1.5406 Å, and the step size was 0.01°. The voltage and current were 40 KV and 40 mA, respectively. The scan speed and the scan range were 0.1 s/step and 10–80°, respectively.
The specific surface areas and porosity of the catalysts were examined using Tristar 3020 II (Micromeritics, Norcross, GA, USA), and the structural parameters were determined by the BET method. Nitrogen was used as the gas adsorbate at 77 K.
The acid strength of the catalysts was measured by the Py-TPD method with an Autochem II2920 (Micromeritics, Norcross, GA, USA). The acidity measurements were carried out by pyridine adsorption IR spectra with Nicolet 6700. The powder samples were molded to thin wafers (~20 mg) and then placed in a treatment cell for 2 h, where the temperature was raised to 500 °C, and in a high vacuum with 1.0 × 10−3 Pa.
The metal loadings of the modified catalysts were measured by ICP-AES with VISTA-MPX (Varian, Palo Alto, CA, USA).
4. Conclusions
The dehydration of 1-butanol to butenes is a major step in the process of converting 1-butanol to jet fuel and accounts for a significant portion of the total costs. An efficient and economic catalytic dehydration process was developed in this study. A high-concentration 1-butanol solution was used as feedstock, which was more consistent with the concentration of butanol from fermentation. Zn-Mn-Co modified γ-Al2O3 was prepared, and the catalytic performance of the catalysts in 1-butanol dehydration to butenes was investigated. The catalytic performance of Zn-Mn-Co/γ-Al2O3 was superior to that of unmodified γ-Al2O3 at different reaction temperatures and WHSV. The reaction temperature and WHSV were optimized by RSM, and, at the optimal conditions, (375 °C and a WHSV of 1.67 h−1), the total selectivity of butene achieved 90%, and the conversion rate of 1-butanol reached 100%, which were 10% and 6% higher than those obtained using unmodified γ-Al2O3. According to the results of characterization, the loading amounts of zinc, manganese, and cobalt were 0.54%, 0.44%, and 0.23%, respectively, and the crystallinity and acidity of γ-Al2O3 were enhanced after the modification. These results provide a theoretical basis for the further optimization of bio-jet fuel production with a high concentration of 1-butanol.
Author Contributions
Methodology, K.-K.C. and J.-A.Z.; software, H.-J.L.; formal analysis, X.Y. and Y.-J.Z.; investigation, J.W.; data curation, Z.-N.L. and S.M.; writing—original draft preparation, J.W.; writing—review and editing, J.W., K.-K.C. and J.-A.Z.; supervision, K.-K.C. and J.-A.Z.; project administration, J.-A.Z.; funding acquisition, J.-A.Z.
Acknowledgments
This research was funded by the National Key R&D Program of China (No. 2016YFE0131300), the project of NSFC-NRCT (No. 51861145103), the Boeing Company (No. 2015-156), and the Foundation of Key Laboratory for Industrial Biocatalysis (Tsinghua Univesity), Ministry of Education (No. 2015302).
Conflicts of Interest
The authors declare no conflict of interest.
References
- Chiaramonti, D.; Prussi, M.; Buffi, M.; Tacconi, D. Sustainable bio kerosene: Process routes and industrial demonstration activities in aviation biofuels. Appl. Energy 2014, 136, 767–774. [Google Scholar] [CrossRef]
- Danilo, S.B.; Adriano, P.M. Jet fuel production in eucalyptus pulp mills: Economics and carbon footprint of ethanol vs. butanol pathway. Bioresour. Technol. 2018, 268, 9–19. [Google Scholar]
- Zhang, W.L.; Liu, Z.Y.; Liu, Z.; Li, F.L. Butanol production from corncob residue using Clostridium beijerinckii NCIMB 8052. Lett. Appl. Microbiol. 2012, 55, 240–246. [Google Scholar] [CrossRef]
- Ujor, V.; Agu, C.V.; Gopalan, V.; Ezeji, T.C. Allopurinol-mediated lignocellulose-derived microbial inhibitor tolerance by Clostridium beijerinckii during acetone-butanol-ethanol (ABE) fermentation. Appl. Microbiol. Biotechnol. 2015, 99, 3729–3740. [Google Scholar] [CrossRef] [PubMed]
- Lin, Z.N.; Liu, H.J.; Yan, X.; Zhou, Y.J.; Cheng, K.K.; Zhang, J.A. High-efficiency acetone-butanol-ethanol production and recovery in non-strict anaerobic gas-stripping fed-batch fermentation. Appl. Microbiol. Biotechnol. 2017, 101, 8029–8039. [Google Scholar] [CrossRef] [PubMed]
- Xue, C.; Zhao, J.B.; Liu, F.F.; Lu, C.C.; Yang, S.T.; Bai, F.W. Two-stage in situ gas stripping for enhanced butanol fermentation and energy-saving product recovery. Bioresour. Technol. 2013, 135, 396–402. [Google Scholar] [CrossRef] [PubMed]
- Xue, C.; Du, G.Q.; Sun, J.X.; Chen, L.J.; Gao, S.S.; Yu, M.L.; Yang, S.T.; Bai, F.W. Characterization of gas stripping and its integration with acetone-butanol-ethanol fermentation for high-efficient butanol production and recovery. Biochem. Eng. J. 2014, 83, 55–61. [Google Scholar] [CrossRef]
- West, R.M.; Braden, D.J.; Dumesic, J.A. Production of alkanes from biomass derived carbohydrates on bi-functional catalysts employing niobium-based supports. J. Catal. 2009, 10, 1743–1746. [Google Scholar] [CrossRef]
- Sun, H.; Blass, S.; Michor, E.; Schmidt, L. Autothermal reforming of butanol to butenes in a staged millisecond reactor: Effect of catalysts and isomers. Appl. Catal. A Gen. 2012, 445–446, 35–41. [Google Scholar] [CrossRef]
- Sedjame, H.J.; Lafaye, G.; Barbier, J., Jr. N-butanol removal over alumina supported platinum catalysts. Appl. Catal. B Environ. 2013, 132–133, 132–141. [Google Scholar] [CrossRef]
- Zhang, D.; Alhajri, R.; Barri, S.A.; Chadwick, D. One-step dehydration and isomerisation of n-butanol to iso-butene over zeolite catalysts. Chem. Commun. 2010, 46, 4088–4090. [Google Scholar] [CrossRef] [PubMed]
- Macho, V.; Jurecekova, E.; Hudec, J. Dehydration of C4 alkanols conjugated with a positional and skeletal isomerisation of the formed C4 alkenes. Appl. Catal. A Gen. 2001, 214, 251–257. [Google Scholar] [CrossRef]
- Wang, L.; Chen, H.Z. Increased fermentability of enzymatically hydrolyzed steam-exploded corn stover for butanol production by removal of fermentation inhibitors. Process Biochem. 2001, 46, 604–607. [Google Scholar] [CrossRef]
- Nahreen, S.; Gupta, R.B. Conversion of the acetone-butanol-ethanol (ABE) mixture to hydrocarbons by catalytic dehydration. Eenergy Fuel 2013, 27, 2116–2125. [Google Scholar] [CrossRef]
- Lopez-Pedrajas, S.; Estevez, R.; Schnee, J.; Schnee, J.; Gaigneaux, E.M.; Luna, D.; Bautista, F.M. Study of the gas-phase glycerol oxidehydration on systems based on transition metals (Co, Fe, V) and aluminium phosphate. Mol. Catal. 2018, 455, 68–77. [Google Scholar] [CrossRef]
- Popa, A.; Sasca, V.; Verdes, O.; Oszko, A. Preparation and catalytic properties of cobalt salts of Keggin type heteropolyacids supported on mesoporous silica. Catal. Today 2018, 306, 233–242. [Google Scholar] [CrossRef]
- Armenta, M.A.; Valdez, R.; Silva-Rodrigo, R.; Olivas, A. Diisopropyl ether production via 2-propanol dehydration using supported iron oxides catalysts. Fuel 2019, 236, 934–941. [Google Scholar] [CrossRef]
- Li, F.Y.; Liu, Z.Z.; Shen, D.J.; Zhang, M.H. Catalytic dehydration of ethanol to ethylene over nickel modified HZSM-5 catalysts. Mod. Chem. Ind. 2013, 33, 54–57. [Google Scholar]
- Wang, W.; Cheng, K.K.; Xue, J.W.; Zhang, J.A. Optimization of ethylene production from ethanol dehydration using Zn-Mn-Co/HZSM-5 by response surface methodology. Chin. J. Biotechnol. 2011, 27, 412–418. [Google Scholar]
- Osman, A.I.; Abu-Dahrieh, J.K.; Rooney, D.W.; Thompson, J.; Halawy, S.A.; Mohamed, M.A. Surface hydrophobicity and acidity effect on alumina catalyst in catalytic methanol dehydration reaction. J. Chem. Technol. Biotechnol. 2017, 92, 2952–2962. [Google Scholar] [CrossRef] [PubMed] [Green Version]
- Said, E.A.A.; El-Wahab, M.M.M.A.; Abdelhak, M.M. The role of Brønsted acid site strength on the catalytic performance of phosphotungstic acid supported on nano γ-alumina catalysts for the dehydration of ethanol to diethyl ether. React. Kinet. Mech. Catal. 2017, 122, 1–17. [Google Scholar] [CrossRef]
- Yu, F.; Zhang, M.H.; Ye, G. Influence of different metal ions on the rehydration properties of aluminas. Acta Sini Pet Process Sect. 1999, 15, 25–27. [Google Scholar]
- Fei, J.H.; Yang, M.X.; Hou, Z.Y.; Zheng, X.M. Effect of the addition of manganese and zinc on the properties of copper-based catalyst for the synthesis of syngas to dimethyl ether. Eenergy Fuel 2004, 18, 1584–1587. [Google Scholar] [CrossRef]
- Thommes, M.; Kaneko, K.; Neimark, A.V.; Olivier, J.P.; Rodriguez-Reinoso, F.; Rouquerol, J.; Sing, K.S.W. Physisorption of gases with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report). Pure Appl. Chem. 2015, 87, 1051–1069. [Google Scholar] [CrossRef]
- Phung, T.K.; Lagazzo, A.; Crespo, M.Á.R.; Escribano, V.S.; Busca, G.A. Study of commercial transition aluminas and of their catalytic activity in the dehydration of ethanol. J. Catal. 2014, 311, 102–113. [Google Scholar] [CrossRef]
- Abattista, F.; Delmastro, S.; Gozzelino, G.; Mazza, D.; Vallino, M.; Busca, G.; Lorenzelli, V.; Ramis, G. Surface characterization of amorphous alumina and its crystallization products. J. Catal. 1989, 117, 42–51. [Google Scholar] [CrossRef]
- Morterra, C.; Magnacca, G. A case study: Surface chemistry and surface structure of catalytic aluminas, as studied by vibrational spectroscopy of adsorbed species. Catal. Today 1996, 27, 497–532. [Google Scholar] [CrossRef]
- Khabtou, S.; Chevreau, T.; Lavalley, J.C. Quantitative infrared study of the distinct acidic hydroxyl groups contained in modified Y zeolites. Microporous Mater. 1994, 3, 133–148. [Google Scholar] [CrossRef]
- Zheng, H.D.; Lin, Y.; Wang, M.C.; Liu, J.; Wu, D.; Chen, J.J.; Yin, G.H.; Oyama, S.T.; Zhao, S.Y. The influence of solvent polarity on the dehydrogenation of isoborneol over a Cu/ZnO/Al2O3 catalyst. Catal. Today 2019, 323, 44–53. [Google Scholar] [CrossRef]
- Ashour, S.S. Factors Affecting the Activity and Selectivity of Alumina Catalysts in the Dehydration of 1-Butanol. Adsorpt. Sci. Technol. 2004, 22, 475–483. [Google Scholar] [CrossRef] [Green Version]
- El-Molla, S.A. Surface and catalytic properties of Cr2O3/MgO system doped with manganese and cobalt oxides. Appl. Catal. A Gen. 2005, 280, 189–197. [Google Scholar] [CrossRef]
- Li, G.; Liu, Y.; Tang, Z.; Liu, C.G. Effects of rehydration of alumina on its structural properties, surface acidity, and HDN activity of quinoline. Appl. Catal. A Gen. 2012, 437–438, 79–89. [Google Scholar] [CrossRef]
Figure 1.
X-ray diffraction patterns of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 2.
Cryogenic nitrogen adsorption-desorption isotherms for γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 2.
Cryogenic nitrogen adsorption-desorption isotherms for γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 3.
Pore size distribution patterns of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 4.
The pyridine temperature-programmed desorption (Py-TPD) profiles of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 4.
The pyridine temperature-programmed desorption (Py-TPD) profiles of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 5.
The Py-IR profiles of γ-Al2O3 and Zn-Mn-Co modified γ-Al2O3.
Figure 6.
Contour plot of the combined effects of temperature and WHSV on butenes yield obtained with Zn-Mn-Co modified γ-Al2O3.
Figure 6.
Contour plot of the combined effects of temperature and WHSV on butenes yield obtained with Zn-Mn-Co modified γ-Al2O3.
Figure 7.
Dehydration of 1-butanol under optimal conditions (375.78 °C and 1.67 h−1 of WHSV) (A): Zn-Mn-Co modified γ-Al2O3. (B): Unmodified γ-Al2O3.
Figure 7.
Dehydration of 1-butanol under optimal conditions (375.78 °C and 1.67 h−1 of WHSV) (A): Zn-Mn-Co modified γ-Al2O3. (B): Unmodified γ-Al2O3.
Figure 8.
Apparatus for butanol dehydration.
Table 1.
Textural properties of the catalysts.
| Catalyst | SBET (m2/g) | Vad (cm3/g) | r (nm) |
|---|---|---|---|
| γ-Al2O3 | 264.46 | 0.67 | 10.14 |
| Zn-Mn-Co/γ-Al2O3 | 211.70 | 0.57 | 10.72 |
Note. SBET is the Brunner-Emmet-Teller (BET) specific surface area, Vad is the cumulative volume of pores, r is the average pore radius.
Table 2.
Amount of the Lewis acid sites on the catalysts. LAS, Lewis acid sites.
| Catalyst | Weak LAS (μmol/g) | Strong LAS (μmol/g) |
|---|---|---|
| γ-Al2O3 | 240.8 | 153.8 |
| Zn-Mn-Co/γ-Al2O3 | 266.2 | 170.2 |
Table 3.
Catalytic properties of γ-Al2O3 at different temperatures. DBE, dibutyl ether.
| Temperature (°C) | Conversion of 1-Butanol (%) | Selectivity of Butenes (%) | Selectivity of DBE (%) | Other Hydrocarbons (%) | ||||
|---|---|---|---|---|---|---|---|---|
| 1- | Trans- | Cis- | Iso- | Total | ||||
| 300 | 71.21 | 65.72 | 3.87 | 6.96 | 0.77 | 77.32 | 21.88 | - |
| 350 | 82.63 | 63.18 | 7.32 | 9.61 | 1.76 | 81.87 | 16.76 | 0.43 |
| 400 | 98.56 | 56.97 | 17.13 | 12.29 | 2.61 | 89.00 | 6.74 | 2.16 |
| 450 | 100 | 47.15 | 20.06 | 17.54 | 2.94 | 87.69 | - | 10.43 |
Note: The weight-hourly space velocity (WHSV) was 2.0 h−1.
Table 4.
Catalytic properties of Zn-Mn-Co/γ-Al2O3 at different temperatures.
| Temperature (°C) | Conversion of 1-Butanol (%) | Selectivity of Butenes (%) | Selectivity of DBE (%) | Other Hydrocarbons (%) | ||||
|---|---|---|---|---|---|---|---|---|
| 1- | Trans- | Cis- | Iso- | Total | ||||
| 300 | 80.34 | 65.11 | 5.70 | 9.77 | 0.82 | 81.39 | 17.21 | - |
| 350 | 95.25 | 64.67 | 9.59 | 12.98 | 1.25 | 88.49 | 9.35 | 0.51 |
| 400 | 100 | 57.79 | 20.45 | 15.13 | 2.87 | 96.24 | - | 2.59 |
| 450 | 100 | 33.62 | 25.05 | 24.29 | 3.77 | 86.73 | - | 11.77 |
Note: The WHSV was 2.0 h−1.
Table 5.
Catalytic properties of γ-Al2O3 at different WHSV.
| WHSV (h−1) | Conversion of 1-Butanol (%) | Selectivity of Butenes (%) | Selectivity of DBE (%) | Other Hydrocarbons (%) | ||||
|---|---|---|---|---|---|---|---|---|
| 1- | Trans- | Cis- | Iso- | Total | ||||
| 1 | 98.01 | 55.58 | 11.21 | 11.05 | 2.48 | 80.32 | 17.89 | 0.37 |
| 2 | 82.63 | 63.18 | 7.31 | 9.62 | 1.76 | 81.87 | 16.76 | 0.43 |
| 3 | 68.56 | 68.69 | 4.82 | 6.70 | 0.83 | 81.04 | 17.22 | 0.39 |
| 4 | 51.04 | 70.75 | 4.28 | 4.53 | 0.13 | 79.69 | 18.52 | 0.32 |
Note: The reaction temperature was 350 °C.
Table 6.
Catalytic properties of Zn-Mn-Co/γ-Al2O3 at different WHSV.
| WHSV (h−1) | Conversion of 1-Butanol (%) | Selectivity of Butenes (%) | Selectivity of DBE (%) | Other Hydrocarbons (%) | ||||
|---|---|---|---|---|---|---|---|---|
| 1- | Trans- | Cis- | Iso- | Total | ||||
| 1 | 100 | 60.60 | 11.58 | 15.29 | 2.90 | 90.37 | 8.05 | 0.48 |
| 2 | 95.25 | 64.67 | 9.59 | 12.98 | 1.25 | 88.49 | 9.35 | 0.51 |
| 3 | 79.45 | 72.65 | 7.16 | 9.69 | 0.74 | 90.24 | 8.87 | 0.41 |
| 4 | 65.49 | 74.97 | 5.74 | 8.10 | 0.36 | 89.17 | 9.01 | 0.48 |
Note. The reaction temperature was 350 °C.
Table 7.
Central composite design and experimental results obtained with Zn-Mn-Co modified γ-Al2O3.
| Run | Temperature (°C) | WHSV (h−1) | Butenes Yield (%) |
|---|---|---|---|
| 1 | 400 | 2.5 | 90.15 |
| 2 | 400 | 2.5 | 90.54 |
| 3 | 350 | 4.0 | 58.80 |
| 4 | 450 | 4.0 | 77.64 |
| 5 | 400 | 2.5 | 89.79 |
| 6 | 450 | 1.0 | 89.23 |
| 7 | 350 | 1.0 | 90.57 |
| 8 | 400 | 2.5 | 89.96 |
| 9 | 400 | 4.0 | 77.21 |
| 10 | 350 | 2.5 | 76.31 |
| 11 | 400 | 1.0 | 99.33 |
| 12 | 400 | 2.5 | 89.82 |
| 13 | 450 | 2.5 | 84.43 |
| 14 | 400 | 2.5 | 88.26 |
Table 8.
Analysis of variance for fitted quadratic polynomial model for total yield of butenes.
| Source | Sum of Squares | F Value | p-Value Prob > F |
|---|---|---|---|
| Model | 1240.91 | 642.51 | <0.0001 |
| X1 (Temperature) | 108.98 | 282.14 | <0.0001 |
| X2 (WHSV) | 715.32 | 1851.86 | <0.0001 |
| X1X2 | 101.65 | 263.15 | <0.0001 |
| X1X1 | 239.26 | 619.40 | <0.0001 |
| X2X2 | 6.15 | 15.93 | <0.0052 |
| Residual | 2.70 | ||
| Lack of Fit | 0.58 | 0.36 | 0.7855 |
| Pure Error | 2.13 | ||
| Cor Total | 1268.49 |
© 2019 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).
Share and Cite
MDPI and ACS Style
Wu, J.; Liu, H.-J.; Yan, X.; Zhou, Y.-J.; Lin, Z.-N.; Mi, S.; Cheng, K.-K.; Zhang, J.-A. Efficient Catalytic Dehydration of High-Concentration 1-Butanol with Zn-Mn-Co Modified γ-Al2O3 in Jet Fuel Production. Catalysts 2019, 9, 93. https://doi.org/10.3390/catal9010093
AMA Style
Wu J, Liu H-J, Yan X, Zhou Y-J, Lin Z-N, Mi S, Cheng K-K, Zhang J-A. Efficient Catalytic Dehydration of High-Concentration 1-Butanol with Zn-Mn-Co Modified γ-Al2O3 in Jet Fuel Production. Catalysts. 2019; 9(1):93. https://doi.org/10.3390/catal9010093
Chicago/Turabian StyleWu, Jing, Hong-Juan Liu, Xiang Yan, Yu-Jie Zhou, Zhang-Nan Lin, Shuo Mi, Ke-Ke Cheng, and Jian-An Zhang. 2019. "Efficient Catalytic Dehydration of High-Concentration 1-Butanol with Zn-Mn-Co Modified γ-Al2O3 in Jet Fuel Production" Catalysts 9, no. 1: 93. https://doi.org/10.3390/catal9010093
APA StyleWu, J., Liu, H. -J., Yan, X., Zhou, Y. -J., Lin, Z. -N., Mi, S., Cheng, K. -K., & Zhang, J. -A. (2019). Efficient Catalytic Dehydration of High-Concentration 1-Butanol with Zn-Mn-Co Modified γ-Al2O3 in Jet Fuel Production. Catalysts, 9(1), 93. https://doi.org/10.3390/catal9010093
Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.
