Membranes

14 pages, 3596 KiB

Open AccessArticle

Features of Electrochemical Hydrogen Pump Based on Irradiated Proton Exchange Membrane

by Nataliya A. Ivanova, Boris V. Ivanov, Ruslan M. Mensharapov, Dmitry D. Spasov, Matvey V. Sinyakov, Seraphim V. Nagorny, Evgeny D. Kazakov, Petr V. Dmitryakov, Artem V. Bakirov and Sergey A. Grigoriev

Membranes 2023, 13(11), 885; https://doi.org/10.3390/membranes13110885 - 20 Nov 2023

Cited by 2 | Viewed by 2346

Abstract

An electrochemical hydrogen pump (EHP) with a proton exchange membrane (PEM) used as part of fusion cycle systems successfully combines the processes of hydrogen extraction, purification and compression in a single device. This work comprises a novel study of the effect of ionizing [...] Read more.

An electrochemical hydrogen pump (EHP) with a proton exchange membrane (PEM) used as part of fusion cycle systems successfully combines the processes of hydrogen extraction, purification and compression in a single device. This work comprises a novel study of the effect of ionizing radiation on the properties of the PEM as part of the EHP. Radiation exposure leads to nonspecific degradation of membranes, changes in their structure, and destruction of side and matrix chains. The findings from this work reveal that the replacement of sulfate groups in the membrane structure with carboxyl and hydrophilic groups leads to a decrease in conductivity from 0.115 to 0.103 S cm⁻¹, which is reflected in halving the device performance at a temperature of 30 °C. The shift of the ionomer peak of small-angle X-ray scattering curves from 3.1 to 4.4 nm and the absence of changes in the water uptake suggested structural changes in the PEM after the irradiation. Increasing the EHP operating temperature minimized the effect of membrane irradiation on the pump performance, but enhanced membrane drying at low pressure and 50 °C, which caused a current density drop from 0.52 to 0.32 A·cm⁻² at 0.5 V. Full article

(This article belongs to the Special Issue Recent Progress in Polymer Electrolyte Membrane Fuel Cells and Water Electrolyzers)

► Show Figures

Figure 1

30 pages, 5698 KiB

Open AccessReview

An Overview of Microbial Fuel Cell Technology for Sustainable Electricity Production

by Wilgince Apollon

Membranes 2023, 13(11), 884; https://doi.org/10.3390/membranes13110884 - 17 Nov 2023

Cited by 3 | Viewed by 6500

Abstract

The over-exploitation of fossil fuels and their negative environmental impacts have attracted the attention of researchers worldwide, and efforts have been made to propose alternatives for the production of sustainable and clean energy. One proposed alternative is the implementation of bioelectrochemical systems (BESs), [...] Read more.

The over-exploitation of fossil fuels and their negative environmental impacts have attracted the attention of researchers worldwide, and efforts have been made to propose alternatives for the production of sustainable and clean energy. One proposed alternative is the implementation of bioelectrochemical systems (BESs), such as microbial fuel cells (MFCs), which are sustainable and environmentally friendly. MFCs are devices that use bacterial activity to break down organic matter while generating sustainable electricity. Furthermore, MFCs can produce bioelectricity from various substrates, including domestic wastewater (DWW), municipal wastewater (MWW), and potato and fruit wastes, reducing environmental contamination and decreasing energy consumption and treatment costs. This review focuses on recent advancements regarding the design, configuration, and operation mode of MFCs, as well as their capacity to produce bioelectricity (e.g., 2203 mW/m²) and fuels (i.e., H₂: 438.7 mg/L and CH₄: 358.7 mg/L). Furthermore, this review highlights practical applications, challenges, and the life-cycle assessment (LCA) of MFCs. Despite the promising biotechnological development of MFCs, great efforts should be made to implement them in a real-time and commercially viable manner. Full article

► Show Figures

Graphical abstract

23 pages, 2923 KiB

Open AccessReview

Electric Fields at the Lipid Membrane Interface

by Yury A. Ermakov

Membranes 2023, 13(11), 883; https://doi.org/10.3390/membranes13110883 - 16 Nov 2023

Cited by 3 | Viewed by 2299

Abstract

This review presents a comprehensive analysis of electric field distribution at the water–lipid membrane interface in the context of its relationship to various biochemical problems. The main attention is paid to the methodological aspects of bioelectrochemical techniques and quantitative analysis of electrical phenomena [...] Read more.

This review presents a comprehensive analysis of electric field distribution at the water–lipid membrane interface in the context of its relationship to various biochemical problems. The main attention is paid to the methodological aspects of bioelectrochemical techniques and quantitative analysis of electrical phenomena caused by the ionization and hydration of the membrane–water interface associated with the phase state of lipids. One of the objectives is to show the unique possibility of controlling changes in the structure of the lipid bilayer initiated by various membrane-active agents that results in electrostatic phenomena at the surface of lipid models of biomembranes—liposomes, planar lipid bilayer membranes (BLMs) and monolayers. A set of complicated experimental facts revealed in different years is analyzed here in order of increasing complexity: from the adsorption of biologically significant inorganic ions and phase rearrangements in the presence of multivalent cations to the adsorption and incorporation of pharmacologically significant compounds into the lipid bilayer, and formation of the layers of macromolecules of different types. Full article

(This article belongs to the Special Issue Synergy of Proteins, Peptides and Lipid Membranes in Vital Cellular Processes)

► Show Figures

Graphical abstract

16 pages, 2564 KiB

Open AccessArticle

Immunogenicity of Escherichia coli Outer Membrane Vesicles: Elucidation of Humoral Responses against OMV-Associated Antigens

by Lorenzo Croia, Giulia Boscato Sopetto, Ilaria Zanella, Elena Caproni, Assunta Gagliardi, Silvia Tamburini, Enrico König, Mattia Benedet, Gabriele Di Lascio, Riccardo Corbellari, Alberto Grandi, Michele Tomasi and Guido Grandi

Membranes 2023, 13(11), 882; https://doi.org/10.3390/membranes13110882 - 16 Nov 2023

Cited by 3 | Viewed by 2692

Abstract

Outer membrane vesicles (OMVs) produced by Gram-negative bacteria have emerged as a novel and flexible vaccine platform. OMVs can be decorated with foreign antigens and carry potent immunostimulatory components. Therefore, after their purification from the culture supernatant, they are ready to be formulated [...] Read more.

Outer membrane vesicles (OMVs) produced by Gram-negative bacteria have emerged as a novel and flexible vaccine platform. OMVs can be decorated with foreign antigens and carry potent immunostimulatory components. Therefore, after their purification from the culture supernatant, they are ready to be formulated for vaccine use. It has been extensively demonstrated that immunization with engineered OMVs can elicit excellent antibody responses against the heterologous antigens. However, the definition of the conditions necessary to reach the optimal antibody titers still needs to be investigated. Here, we defined the protein concentrations required to induce antigen-specific antibodies, and the amount of antigen and OMVs necessary and sufficient to elicit saturating levels of antigen-specific antibodies. Since not all antigens can be expressed in OMVs, we also investigated the effectiveness of vaccines in which OMVs and purified antigens are mixed together without using any procedure for their physical association. Our data show that in most of the cases OMV–antigen mixtures are very effective in eliciting antigen-specific antibodies. This is probably due to the capacity of OMVs to “absorb” antigens, establishing sufficiently stable interactions that allow antigen–OMV co-presentation to the same antigen presenting cell. In those cases when antigen–OMV interaction is not sufficiently stable, the addition of alum to the formulation guarantees the elicitation of high titers of antigen-specific antibodies. Full article

(This article belongs to the Special Issue Recent Advances in Outer Membrane Vesicles)

► Show Figures

Figure 1

17 pages, 7257 KiB

Open AccessArticle

Research on the Performance of Self-Made Open-Cathode Fuel Cell Stacks under Different Operating Conditions

by Qiang Bai, Zhenghong Liu and Chuangyu Hsieh

Membranes 2023, 13(11), 881; https://doi.org/10.3390/membranes13110881 - 13 Nov 2023

Cited by 1 | Viewed by 2120

Abstract

The traditional fuel cell power system requires external ventilation and humidification systems for both the anode and cathode, which not only increases the application cost but also restrict its widespread use. In order to further enhance the applicability and reduce the operating costs [...] Read more.

The traditional fuel cell power system requires external ventilation and humidification systems for both the anode and cathode, which not only increases the application cost but also restrict its widespread use. In order to further enhance the applicability and reduce the operating costs of fuel cell power systems, this paper investigates the open-cathode proton exchange membrane fuel cell power system. This approach not only lowers the cost but also reduces the weight of the power system, enabling its potential application in a wider range of vehicles. In this study, two versions of the open-cathode fuel cell stacks were developed and performance and stability tests were conducted under various operating conditions. Additionally, tests were carried out with different materials of carbon paper to find a balance between performance and stability. Through the research presented in this paper, the application scope of fuel cells has been expanded, providing valuable insights for their further development. Full article

(This article belongs to the Special Issue Fabrication, Characterization and Application of Organic/Inorganic Film Membranes and Advanced Materials (Volume III))

► Show Figures

Figure 1

14 pages, 4352 KiB

Open AccessArticle

Innovative Approaches to Poultry Processing Wastewater Treatment: The Stainless Steel Ultrafiltration Membrane as a Viable Option

by Saubana Olorunsola Dada, Chidambaram Thamariselvan, Mahmood Jebur and Sumith Ranil Wickramasinghe

Membranes 2023, 13(11), 880; https://doi.org/10.3390/membranes13110880 - 11 Nov 2023

Viewed by 2108

Abstract

In pursuit of sustainability, we explored replacing conventional dissolved air floatation (DAF) in poultry processing wastewater (PPW) treatment with a precisely tuned 0.02 µm stainless-steel ultrafiltration (SSUF) membrane. SSUF is a robust, homogenously porous membrane with strong chemical resistance, ease of cleaning, and [...] Read more.

In pursuit of sustainability, we explored replacing conventional dissolved air floatation (DAF) in poultry processing wastewater (PPW) treatment with a precisely tuned 0.02 µm stainless-steel ultrafiltration (SSUF) membrane. SSUF is a robust, homogenously porous membrane with strong chemical resistance, ease of cleaning, and exceptional resistance to organic fouling. Unlike polymeric membranes, it can be regenerated multiple times, making it a cost-effective choice due to its compatibility with harsh chemical cleaning. The PPW used for the study was untreated wastewater from all processing units and post-initial screening. Our study revealed the SSUF membrane’s exceptional efficiency at eliminating contaminants. It achieved an impressive removal rate of up to 99.9% for total suspended solids (TSS), oil, grease, E. coli, and coliform. Additionally, it displayed a notable reduction in chemical oxygen demand (COD), biochemical oxygen demand (BOD), and total Kjeldahl nitrogen (TKN), up to 90%, 76%, and 76%, respectively. Our investigation further emphasized the SSUF membrane’s ability in pathogen removal, affirming its capacity to effectively eradicate up to 99.99% of E. coli and coliform. The measured critical flux of the membrane was 48 Lm⁻²h⁻¹ at 38 kPa pressure and 1.90 m/s cross-flow velocity. In summary, our study highlights the considerable potential of the SSUF membrane. Its robust performance treating PPW offers a promising avenue for reducing its environmental impact and advocating for sustainable wastewater management practices. Full article

► Show Figures

Figure 1

11 pages, 1735 KiB

Open AccessArticle

Brownian Aging as One of the Mechanistic Components That Shape the Single-Channel Ionic Currents through Biological and Synthetic Membranes

by Agata Wawrzkiewicz-Jałowiecka and Andrzej Fuliński

Membranes 2023, 13(11), 879; https://doi.org/10.3390/membranes13110879 - 11 Nov 2023

Viewed by 1479

Abstract

Semipermeable membranes enable the separation of a given system from its environment. In biological terms, they are responsible for cells’ identity. In turn, the functioning of ion channels is crucial for the control of ionic fluxes across the membranes and, consequently, for the [...] Read more.

Semipermeable membranes enable the separation of a given system from its environment. In biological terms, they are responsible for cells’ identity. In turn, the functioning of ion channels is crucial for the control of ionic fluxes across the membranes and, consequently, for the exchange of chemical and electrical signals. This paper presents a model and simulations of currents through ionic nanochannels in an attempt to better understand the physical mechanism(s) of open/closed (O/C) sequences, i.e., random interruptions of ionic flows through channels observed in all known biochannels and in some synthetic nanopores. We investigate whether aging, i.e., the changes in Brownian motion characteristics with the lapse of time, may be at least one of the sources of the O/C sequences (in addition to the gating machinery in biochannels). The simulations based on the approximated nanostructure of ion channels confirm this postulation. The results also show the possibility of changing the O/C characteristics through an appropriate alteration of the channel surroundings. This observation may be valuable in technical uses of nanochannels in synthetic membranes and allow for a better understanding of the reason for the differences between the biochannels’ activity in diverse biological membranes. Proposals of experimental verification of this aging O/C hypothesis are also presented. Full article

(This article belongs to the Special Issue Function and Malfunction of Ion Channels in Biological Cell Membrane)

► Show Figures

Graphical abstract

18 pages, 2604 KiB

Open AccessEditor’s ChoiceArticle

The Effect of Calcium Ions on hIAPP Channel Activity: Possible Implications in T2DM

by Daniela Meleleo, Giuseppe Cibelli, Anna Valenzano, Maria Mastrodonato and Rosanna Mallamaci

Membranes 2023, 13(11), 878; https://doi.org/10.3390/membranes13110878 - 9 Nov 2023

Cited by 1 | Viewed by 1967

Abstract

The calcium ion (Ca²⁺) has been linked to type 2 diabetes mellitus (T2DM), although the role of Ca²⁺ in this disorder is the subject of intense investigation. Serum Ca²⁺ dyshomeostasis is associated with the development of insulin resistance, reduced [...] Read more.

The calcium ion (Ca²⁺) has been linked to type 2 diabetes mellitus (T2DM), although the role of Ca²⁺ in this disorder is the subject of intense investigation. Serum Ca²⁺ dyshomeostasis is associated with the development of insulin resistance, reduced insulin sensitivity, and impaired glucose tolerance. However, the molecular mechanisms involving Ca²⁺ ions in pancreatic β-cell loss and subsequently in T2DM remain poorly understood. Implicated in the decline in β-cell functions are aggregates of human islet amyloid polypeptide (hIAPP), a small peptide secreted by β-cells that shows a strong tendency to self-aggregate into β-sheet-rich aggregates that evolve toward the formation of amyloid deposits and mature fibrils. The soluble oligomers of hIAPP can permeabilize the cell membrane by interacting with bilayer lipids. Our study aimed to evaluate the effect of Ca²⁺ on the ability of the peptide to incorporate and form ion channels in zwitterionic planar lipid membranes (PLMs) composed of palmitoyl-oleoyl-phosphatidylcholine (POPC) and on the aggregation process of hIAPP molecules in solution. Our results may help to clarify the link between Ca²⁺ ions, hIAPP peptide, and consequently the pathophysiology of T2DM. Full article

(This article belongs to the Special Issue Structure-Function Relationships and Biological Processes of Membrane Proteins)

► Show Figures

Graphical abstract

25 pages, 5272 KiB

Open AccessArticle

Sterilized Polyhexanide-Releasing Chitosan Membranes with Potential for Use in Antimicrobial Wound Dressings

by Luís M. Vaz, Rita Branco, Paula V. Morais and António Jorge Guiomar

Membranes 2023, 13(11), 877; https://doi.org/10.3390/membranes13110877 - 8 Nov 2023

Cited by 1 | Viewed by 2029

Abstract

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan [...] Read more.

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited a water swelling capacity of 748%, a water drop penetration time of 11 s in a dry membrane and a water vapor transmission rate of 34,400 g H₂O/m²/24 h when in contact with water. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. When these membranes and a commercial PHMB-releasing AMD were assayed under the same conditions, albeit far from the in vivo conditions, their drug release kinetics were comparable, releasing PHMB for ca. 6 and 4 h, respectively. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds and blood clotting activity. The obtained results suggest that these membranes may have potential for use in the development of AMDs. Full article

(This article belongs to the Section Membrane Applications)

► Show Figures

Figure 1

16 pages, 1899 KiB

Open AccessReview

Application of Metal Oxide Nanoparticles in the Field of Potentiometric Sensors: A Review

by Nikola Lenar, Robert Piech, Cecylia Wardak and Beata Paczosa-Bator

Membranes 2023, 13(11), 876; https://doi.org/10.3390/membranes13110876 - 7 Nov 2023

Cited by 5 | Viewed by 2394

Abstract

Recently, there has been rapid development of electrochemical sensors, and there have been numerous reports in the literature that describe new constructions with improved performance parameters. Undoubtedly, this is due to the fact that those sensors are characterized by very good analytical parameters, [...] Read more.

Recently, there has been rapid development of electrochemical sensors, and there have been numerous reports in the literature that describe new constructions with improved performance parameters. Undoubtedly, this is due to the fact that those sensors are characterized by very good analytical parameters, and at the same time, they are cheap and easy to use, which distinguishes them from other analytical tools. One of the trends observed in their development is the search for new functional materials. This review focuses on potentiometric sensors designed with the use of various metal oxides. Metal oxides, because of their remarkable properties including high electrical capacity and mixed ion-electron conductivity, have found applications as both sensing layers (e.g., of screen-printing pH sensors) or solid-contact layers and paste components in solid-contact and paste-ion-selective electrodes. All the mentioned applications of metal oxides are described in the scope of the paper. This paper presents a survey on the use of metal oxides in the field of the potentiometry method as both single-component layers and as a component of hybrid materials. Metal oxides are allowed to obtain potentiometric sensors of all-solid-state construction characterized by remarkable analytical parameters. These new types of sensors exhibit properties that are competitive with those of the commonly used conventional electrodes. Different construction solutions and various metal oxides were compared in the scope of this review based on their analytical parameters. Full article

(This article belongs to the Section Membrane Surfaces and Interfaces)

► Show Figures

Figure 1

14 pages, 8112 KiB

Open AccessArticle

Hydrogen-Tolerant La_0.6Ca_0.4Co_0.2Fe_0.8O_3–d Oxygen Transport Membranes from Ultrasonic Spray Synthesis for Plasma-Assisted CO₂ Conversion

by Aasir Rashid, Hyunjung Lim, Daniel Plaz, Giamper Escobar Cano, Marc Bresser, Katharina-Sophia Wiegers, Giorgia Confalonieri, Sungho Baek, Guoxing Chen, Armin Feldhoff, Andreas Schulz, Anke Weidenkaff and Marc Widenmeyer

Membranes 2023, 13(11), 875; https://doi.org/10.3390/membranes13110875 - 7 Nov 2023

Cited by 1 | Viewed by 2185

Abstract

La_0.6Ca_0.4Co_1–xFe_xO_3–d in its various compositions has proven to be an excellent CO₂-resistant oxygen transport membrane that can be used in plasma-assisted CO₂ conversion. With the goal of incorporating green [...] Read more.

La_0.6Ca_0.4Co_1–xFe_xO_3–d in its various compositions has proven to be an excellent CO₂-resistant oxygen transport membrane that can be used in plasma-assisted CO₂ conversion. With the goal of incorporating green hydrogen into the CO₂ conversion process, this work takes a step further by investigating the compatibility of La_0.6Ca_0.4Co_1–xFe_xO_3–d membranes with hydrogen fed into the plasma. This will enable plasma-assisted conversion of the carbon monoxide produced in the CO₂ reduction process into green fuels, like methanol. This requires the La_0.6Ca_0.4Co_1–xFe_xO_3–d membranes to be tolerant towards reducing conditions of hydrogen_. The hydrogen tolerance of La_0.6Ca_0.4Co_1–xFe_xO_3–d (x = 0.8) was studied in detail. A faster and resource-efficient route based on ultrasonic spray synthesis was developed to synthesise the La_0.6Ca_0.4Co_0.2Fe_0.8O_3–d membranes. The La_0.6Ca_0.4Co_0.2Fe_0.8O_3–d membrane developed using ultrasonic spray synthesis showed similar performance in terms of its oxygen permeation when compared with the ones synthesised with conventional techniques, such as co-precipitation, sol–gel, etc., despite using 30% less cobalt. Full article

► Show Figures

Figure 1

22 pages, 1869 KiB

Open AccessEditor’s ChoiceReview

Adsorptive Membranes Incorporating Ionic Liquids (ILs), Deep Eutectic Solvents (DESs) or Graphene Oxide (GO) for Metal Salts Extraction from Aqueous Feed

by Liyan Qalyoubi, Ioannis Zuburtikudis, Hadil Abu Khalifeh and Enas Nashef

Membranes 2023, 13(11), 874; https://doi.org/10.3390/membranes13110874 - 3 Nov 2023

Cited by 4 | Viewed by 2461

Abstract

Water scarcity is a significant concern, particularly in arid regions, due to the rapid growth in population, industrialization, and climate change. Seawater desalination has emerged as a conventional and reliable solution for obtaining potable water. However, conventional membrane-based seawater desalination has drawbacks, such [...] Read more.

Water scarcity is a significant concern, particularly in arid regions, due to the rapid growth in population, industrialization, and climate change. Seawater desalination has emerged as a conventional and reliable solution for obtaining potable water. However, conventional membrane-based seawater desalination has drawbacks, such as high energy consumption resulting from a high-pressure requirement, as well as operational challenges like membrane fouling and high costs. To overcome these limitations, it is crucial to enhance the performance of membranes by increasing their efficiency, selectivity, and reducing energy consumption and footprint. Adsorptive membranes, which integrate adsorption and membrane technologies, offer a promising approach to address the drawbacks of standalone membranes. By incorporating specific materials into the membrane matrix, composite membranes have demonstrated improved permeability, selectivity, and reduced pressure requirements, all while maintaining effective pollutant rejection. Researchers have explored different adsorbents, including emerging materials such as ionic liquids (ILs), deep eutectic solvents (DESs), and graphene oxide (GO), for embedding into membranes and utilizing them in various applications. This paper aims to discuss the existing challenges in the desalination process and focus on how these materials can help overcome these challenges. It will also provide a comprehensive review of studies that have reported the successful incorporation of ILs, DESs, and GO into membranes to fabricate adsorptive membranes for desalination. Additionally, the paper will highlight both the current and anticipated challenges in this field, as well as present prospects, and provide recommendations for further advancements. Full article

► Show Figures

Figure 1

12 pages, 2830 KiB

Open AccessArticle

Electrotransport Properties of Perfluorinated Cation-Exchange Membranes of Various Thickness

by Irina Falina, Natalia Loza, Marina Brovkina, Ekaterina Titskaya, Sergey Timofeev and Natalia Kononenko

Membranes 2023, 13(11), 873; https://doi.org/10.3390/membranes13110873 - 3 Nov 2023

Viewed by 1668

Abstract

The present work discusses the influence of the thickness of MF-4SK perfluorinated sulfonic cation-exchange membranes on their electrotransport properties in hydrochloric acid solutions. It is found that diffusion permeability and conductivity are primarily determined with the specific water content of the membranes and [...] Read more.

The present work discusses the influence of the thickness of MF-4SK perfluorinated sulfonic cation-exchange membranes on their electrotransport properties in hydrochloric acid solutions. It is found that diffusion permeability and conductivity are primarily determined with the specific water content of the membranes and increase with their increase. Analysis of the contribution of reverse diffusion through the membrane to the value of the limiting current shows that it can reach 20% for membranes with a thickness of 60 μm. A study of the characteristics of the fuel cell with perfluorinated membranes of different thicknesses shows that the membrane thickness affects both the ohmic resistance of the membrane-electrode assembly and the diffusion limitations of proton transport in polymer electrolytes. Full article

(This article belongs to the Special Issue Electromembrane Processes: From Fundamentals to Applications)

► Show Figures

Figure 1

38 pages, 3896 KiB

Open AccessReview

A Comprehensive Review of Performance of Polyacrylonitrile-Based Membranes for Forward Osmosis Water Separation and Purification Process

by Nada Abounahia, Arqam Azad Shahab, Maryam Mohammad Khan, Hazim Qiblawey and Syed Javaid Zaidi

Membranes 2023, 13(11), 872; https://doi.org/10.3390/membranes13110872 - 3 Nov 2023

Cited by 2 | Viewed by 3368

Abstract

Polyacrylonitrile (PAN), with its unique chemical, electrical, mechanical, and thermal properties, has become a crucial acrylic polymer for the industry. This polymer has been widely used to fabricate ultrafiltration, nanofiltration, and reverse osmosis membranes for water treatment applications. However, it recently started to [...] Read more.

Polyacrylonitrile (PAN), with its unique chemical, electrical, mechanical, and thermal properties, has become a crucial acrylic polymer for the industry. This polymer has been widely used to fabricate ultrafiltration, nanofiltration, and reverse osmosis membranes for water treatment applications. However, it recently started to be used to fabricate thin-film composite (TFC) and fiber-based forward osmosis (FO) membranes at a lab scale. Phase inversion and electrospinning methods were the most utilized techniques to fabricate PAN-based FO membranes. The PAN substrate layer could function as a good support layer to create TFC and fiber membranes with excellent performance under FO process conditions by selecting the proper modification techniques. The various modification techniques used to enhance PAN-based FO performance include interfacial polymerization, layer-by-layer assembly, simple coating, and incorporating nanofillers. Thus, the fabrication and modification techniques of PAN-based porous FO membranes have been highlighted in this work. Also, the performance of these FO membranes was investigated. Finally, perspectives and potential directions for further study on PAN-based FO membranes are presented in light of the developments in this area. This review is expected to aid the scientific community in creating novel effective porous FO polymeric membranes based on PAN polymer for various water and wastewater treatment applications. Full article

(This article belongs to the Special Issue Membranes Desalination of Sea/Brackish Water)

► Show Figures

Figure 1

13 pages, 1020 KiB

Open AccessArticle

Membrane-Mediated Cooperative Interactions of CD47 and SIRPα

by Long Li, Chen Gui, Jinglei Hu and Bartosz Różycki

Membranes 2023, 13(11), 871; https://doi.org/10.3390/membranes13110871 - 2 Nov 2023

Cited by 3 | Viewed by 2100

Abstract

The specific binding of the ubiquitous ‘marker of self’ protein CD47 to the SIRP

α

protein anchored in the macrophage plasma membrane results in the inhibition of the engulfment of ‘self’ cells by macrophages and thus constitutes a key checkpoint of our innate [...] Read more.

The specific binding of the ubiquitous ‘marker of self’ protein CD47 to the SIRP

α

protein anchored in the macrophage plasma membrane results in the inhibition of the engulfment of ‘self’ cells by macrophages and thus constitutes a key checkpoint of our innate immune system. Consequently, the CD47–SIRP

α

protein complex has been recognized as a potential therapeutic target in cancer and inflammation. Here, we introduce a lattice-based mesoscale model for the biomimetic system studied recently in fluorescence microscopy experiments where GFP-tagged CD47 proteins on giant plasma membrane vesicles bind to SIRP

α

proteins immobilized on a surface. Computer simulations of the lattice-based mesoscale model allow us to study the biomimetic system on multiple length scales, ranging from single nanometers to several micrometers and simultaneously keep track of single CD47–SIRP

α

binding and unbinding events. Our simulations not only reproduce data from the fluorescence microscopy experiments but also are consistent with results of several other experiments, which validates our numerical approach. In addition, our simulations yield quantitative predictions on the magnitude and range of effective, membrane-mediated attraction between CD47–SIRP

α

complexes. Such detailed information on CD47–SIRP

α

interactions cannot be obtained currently from experiments alone. Our simulation results thus extend the present understanding of cooperative effects in CD47–SIRP

α

interactions and may have an influence on the advancement of new cancer treatments. Full article

(This article belongs to the Section Biological Membrane Dynamics and Computation)

► Show Figures

Figure 1

16 pages, 4078 KiB

Open AccessArticle

Chemically Stable Styrenic Electrospun Membranes with Tailorable Surface Chemistry

by Maura Sepesy, Tuli Banik, Joelle Scott, Luke A. F. Venturina, Alec Johnson, Bernadette L. Schneider, Megan M. Sibley and Christine E. Duval

Membranes 2023, 13(11), 870; https://doi.org/10.3390/membranes13110870 - 2 Nov 2023

Cited by 1 | Viewed by 2429

Abstract

Membranes with tailorable surface chemistry have applications in a wide range of industries. Synthesizing membranes from poly(chloromethyl styrene) directly incorporates an alkyl halide surface-bound initiator which can be used to install functional groups via S_N2 chemistry or graft polymerization techniques. In [...] Read more.

Membranes with tailorable surface chemistry have applications in a wide range of industries. Synthesizing membranes from poly(chloromethyl styrene) directly incorporates an alkyl halide surface-bound initiator which can be used to install functional groups via S_N2 chemistry or graft polymerization techniques. In this work, poly(chloromethyl styrene) membranes were synthesized through electrospinning. After fabrication, membranes were crosslinked with a diamine, and the chemical resistance of the membranes was evaluated by exposure to 10 M nitric acid, ethanol, or tetrahydrofuran for 24 h. The resulting membranes had diameters on the order of 2–5 microns, porosities of >80%, and permeance on the order of 10,000 L/m²/h/bar. Crosslinking the membranes generally increased the chemical stability. The degree of crosslinking was approximated using elemental analysis for nitrogen and ranged from 0.5 to 0.9 N%. The poly(chloromethyl styrene) membrane with the highest degree of crosslinking did not dissolve in THF after 24 h and retained its high permeance after solvent exposure. The presented chemically resistant membranes can serve as a platform technology due to their versatile surface chemistry and can be used in membrane manufacturing techniques that require the membrane to be contacted with organic solvents or monomers. They can also serve as a platform for separations that are performed in strong acids. Full article

(This article belongs to the Special Issue Women’s Special Issue Series: Membrane Materials and Applications)

► Show Figures

Graphical abstract

26 pages, 18195 KiB

Open AccessArticle

Influence of Intramineral Proteins on the Growth of Carbonate Crystals Using as a Scaffold Membranes of Ratite Birds and Crocodiles Eggshells

by Nerith R. Elejalde-Cadena, Denisse Hernández, Francesco Capitelli, Selene R. Islas, Maria J. Rosales-Hoz, Michele Zema, Serena C. Tarantino, Dritan Siliqi and Abel Moreno

Membranes 2023, 13(11), 869; https://doi.org/10.3390/membranes13110869 - 1 Nov 2023

Cited by 1 | Viewed by 2280

Abstract

The lack of information on structural basis where proteins are involved, as well as the biomineralization processes of different systems such as bones, diatom frustules, and eggshells, have intrigued scientists from different fields for decades. This scientific curiosity has led to the use [...] Read more.

The lack of information on structural basis where proteins are involved, as well as the biomineralization processes of different systems such as bones, diatom frustules, and eggshells, have intrigued scientists from different fields for decades. This scientific curiosity has led to the use of methodologies that help understand the mechanism involved in the formation of these complex structures. Therefore, this work focuses on the use of eggshell membranes from different species of ratites (emu and ostrich) and reptiles (two species of crocodiles) as a model to differentiate biocalcification and biosilicification by introducing calcium phosphate or silica inside the membrane fiber mantles. We performed this to obtain information about the process of eggshell formation as well as the changes that occur in the membrane during crystal formation. In order to identify and understand the early processes leading to the formation of the microstructures present in the eggshell, we decided to carry out the synthesis of silica-carbonate of calcium, barium, and strontium called biomorph in the presence of intramineral proteins. This was carried out to evaluate the influence of these proteins on the formation of specific structures. We found that the proteins on untreated membranes, present a structural growth similar to those observed in the inner part of the eggshell, while in treated membranes, the structures formed present a high similarity with those observed in the outer and intermediate part of the eggshell. Finally, a topographic and molecular analysis of the biomorphs and membranes was performed by scanning electron microscopy (SEM), Raman and Fourier-transform Infrared (FTIR) spectroscopies. Full article

(This article belongs to the Special Issue Structure-Function Relationships and Biological Processes of Membrane Proteins)

► Show Figures

Graphical abstract

15 pages, 1517 KiB

Open AccessArticle

Prediction of Flux and Rejection Coefficients in the Removal of Emerging Pollutants Using a Nanofiltration Membrane

by Asunción M. Hidalgo, María Gómez, María D. Murcia, Elisa Gómez, Gerardo León and Irene Alfaro

Membranes 2023, 13(11), 868; https://doi.org/10.3390/membranes13110868 - 1 Nov 2023

Cited by 1 | Viewed by 2447

Abstract

The removal of three emerging pollutants: carbamazepine, ketoprofen, and bisphenol A, has been studied using the nanofiltration flat sheet membrane NF99HF. The removal efficiencies of the membrane have been evaluated by two system characteristic parameters: permeate flux and rejection coefficient. The influence of [...] Read more.

The removal of three emerging pollutants: carbamazepine, ketoprofen, and bisphenol A, has been studied using the nanofiltration flat sheet membrane NF99HF. The removal efficiencies of the membrane have been evaluated by two system characteristic parameters: permeate flux and rejection coefficient. The influence of two operating variables has been analysed: operating pressure and feed concentration. Before and after the tests with emerging pollutants, the membrane has been characterized by determining its water permeability coefficient and its magnesium chloride rejection coefficient to find out if the removal of emerging pollutants causes membrane fouling. The results show that operating pressure has significant separation effects, obtaining the highest efficiencies at a pressure of 20 bar for pollutant concentrations between 5 and 25 mg/L. Moreover, rejection of ketoprofen was found to be dependent on electrostatic repulsion, while rejection of bisphenol A was significantly affected by adsorption onto the membrane. Finally, the experimental data have been fitted to the solution diffusion model and to the simplified model of Spiegler-Kedem-Katchalsky to predict the behaviour of the nanofiltration membrane in the removal of the tested pollutants. Good agreement between the experimental and predicted carbamazepine and bisphenol A data has been obtained with each model, respectively. Full article

(This article belongs to the Collection New Challenges in Membranes for Water and Wastewater Application)

► Show Figures

Figure 1

14 pages, 4181 KiB

Open AccessArticle

Comparative Study of Membrane Fouling with Aeration Shear Stress in Filtration of Different Substances

by Weihao Yao, Bing Wang and Kaisong Zhang

Membranes 2023, 13(11), 867; https://doi.org/10.3390/membranes13110867 - 1 Nov 2023

Cited by 1 | Viewed by 1841

Abstract

The formation process of membrane fouling is complex and diverse, which is an important problem that needs to be overcome in membrane applications. In this paper, three foulant systems consisting of humic acid, humic acid plus Ca²⁺ and humic acid plus Ca [...] Read more.

The formation process of membrane fouling is complex and diverse, which is an important problem that needs to be overcome in membrane applications. In this paper, three foulant systems consisting of humic acid, humic acid plus Ca²⁺ and humic acid plus Ca²⁺ plus yeast were selected to compare membrane fouling processes with different aeration intensities. The aim was to establish the quantitative relationship between membrane fouling rate and shear stress, respectively, in a large-scale flat sheet MBR (FSMBR). The shear stress values at different aeration intensities were obtained using computational fluid dynamics (CFD). The membrane fouling rate during the filtration of different substances was measured by performing experiments. The comparison results showed that the membrane fouling rate varied greatly during the filtration of different substances. With the help of particle size distribution, the effect of different shear forces on floc size was further explored. Using the dual control of fouling rate and floc size, the recommended aeration intensity was 6~8 L/(m²·min). Full article

(This article belongs to the Special Issue Membrane Fouling and Antifouling Strategies in Water and Wastewater Treatment)

► Show Figures

Figure 1

22 pages, 3267 KiB

Open AccessReview

Electrometric and Electron Paramagnetic Resonance Measurements of a Difference in the Transmembrane Electrochemical Potential: Photosynthetic Subcellular Structures and Isolated Pigment–Protein Complexes

by Alexey Yu. Semenov and Alexander N. Tikhonov

Membranes 2023, 13(11), 866; https://doi.org/10.3390/membranes13110866 - 1 Nov 2023

Viewed by 1931

Abstract

A transmembrane difference in the electrochemical potentials of protons (Δμ_H+) serves as a free energy intermediate in energy-transducing organelles of the living cell. The contributions of two components of the Δμ_H+ (electrical, Δψ, and concentrational, ΔpH) to the overall Δμ [...] Read more.

A transmembrane difference in the electrochemical potentials of protons (Δμ_H+) serves as a free energy intermediate in energy-transducing organelles of the living cell. The contributions of two components of the Δμ_H+ (electrical, Δψ, and concentrational, ΔpH) to the overall Δμ_H+ value depend on the nature and lipid composition of the energy-coupling membrane. In this review, we briefly consider several of the most common instrumental (electrometric and EPR) methods for numerical estimations of Δψ and ΔpH. In particular, the kinetics of the flash-induced electrometrical measurements of Δψ in bacterial chromatophores, isolated bacterial reaction centers, and Photosystems I and II of the oxygenic photosynthesis, as well as the use of pH-sensitive molecular indicators and kinetic data regarding pH-dependent electron transport in chloroplasts, have been reviewed. Further perspectives on the application of these methods to solve some fundamental and practical problems of membrane bioenergetics are discussed. Full article

(This article belongs to the Special Issue Artificial Models of Biological Membranes—2nd Edition)

► Show Figures

Graphical abstract

18 pages, 4450 KiB

Open AccessArticle

Preparation and Characterization of New and Low-Cost Ceramic Flat Membranes Based on Zeolite-Clay for the Removal of Indigo Blue Dye Molecules

by Yassine Khmiri, Afef Attia, Hajer Aloulou, Lasâad Dammak, Lassaad Baklouti and Raja Ben Amar

Membranes 2023, 13(11), 865; https://doi.org/10.3390/membranes13110865 - 31 Oct 2023

Cited by 6 | Viewed by 2040

Abstract

Composite flat membranes were prepared using a dry uniaxial pressing process. The effect of the sintering temperature (850–950 °C) and smectite proportion (10–50 wt.%) on membrane properties, such as microstructure, mechanical strength, water permeability, and treatment performances, was explored. It was observed that [...] Read more.

Composite flat membranes were prepared using a dry uniaxial pressing process. The effect of the sintering temperature (850–950 °C) and smectite proportion (10–50 wt.%) on membrane properties, such as microstructure, mechanical strength, water permeability, and treatment performances, was explored. It was observed that increasing the sintering temperature and adding higher amounts of smectite increased the mechanical strength and shrinkage. Therefore, 850 °C was chosen as the optimum sintering temperature because the composite membranes had a very low shrinkage that did not exceed 5% with high mechanical strength, above 23 MPa. The study of smectite addition (10–50 wt.%) showed that the pore size and water permeability were significantly reduced from 0.98 to 0.75 µm and from 623 to 371 L·h⁻¹·m⁻²·bar⁻¹, respectively. Furthermore, the application of the used membranes in the treatment of indigo blue (IB) solutions exhibited an almost total turbidity removal. While the removal of color and COD decreased from 95% to 76%, respectively, they decreased from 95% to 52% when the amount of smectite increased. To verify the treated water’s low toxicity, a germination test was performed. It has been shown that the total germination of linseed grains irrigated by M_S10-Z90 membrane permeate was identical to that irrigated with distilled water. Finally, based on its promising properties, its excellent separation efficiency, and its low energy consumption, the M_S10-Z90 (10 wt.% smectite and 90 wt.% zeolite) sintered at 850 °C could be recommended for the treatment of colored industrial wastewater. Full article

(This article belongs to the Special Issue Research on Polymeric, Composite and Biological Membranes at UPEC: State-of-the-Art and Perspectives)

► Show Figures

Figure 1

13 pages, 5277 KiB

Open AccessArticle

Effect of CM15 on Supported Lipid Bilayer Probed by Atomic Force Microscopy

by Olivia D. Walsh, Leona Choi and Krishna P. Sigdel

Membranes 2023, 13(11), 864; https://doi.org/10.3390/membranes13110864 - 28 Oct 2023

Cited by 1 | Viewed by 2143

Abstract

Antimicrobial peptides are key components of the immune system. These peptides affect the membrane in various ways; some form nano-sized pores, while others only produce minor defects. Since these peptides are increasingly important in developing antimicrobial drugs, understanding the mechanism of their interactions [...] Read more.

Antimicrobial peptides are key components of the immune system. These peptides affect the membrane in various ways; some form nano-sized pores, while others only produce minor defects. Since these peptides are increasingly important in developing antimicrobial drugs, understanding the mechanism of their interactions with lipid bilayers is critical. Here, using atomic force microscopy (AFM), we investigated the effect of a synthetic hybrid peptide, CM15, on the membrane surface comprising E. coli polar lipid extract. Direct imaging of supported lipid bilayers exposed to various concentrations of the peptide revealed significant membrane remodeling. We found that CM15 interacts with supported lipid bilayers and forms membrane-spanning defects very quickly. It is found that CM15 is capable of remodeling both leaflets of the bilayer. For lower CM15 concentrations, punctate void-like defects were observed, some of which re-sealed themselves as a function of time. However, for CM15 concentrations higher than 5 µM, the defects on the bilayers became so widespread that they disrupted the membrane integrity completely. This work enhances the understanding of CM15 interactions with the bacterial lipid bilayer. Full article

(This article belongs to the Special Issue Membrane Interaction between Lipids, Proteins and Peptides)

► Show Figures

Figure 1

12 pages, 5108 KiB

Open AccessArticle

Stability of Filled PDMS Pervaporation Membranes in Bio-Ethanol Recovery from a Real Fermentation Broth

by Cédric Van Goethem, Parimal V. Naik, Miet Van de Velde, Jim Van Durme, Alex Verplaetse and Ivo F. J. Vankelecom

Membranes 2023, 13(11), 863; https://doi.org/10.3390/membranes13110863 - 27 Oct 2023

Cited by 2 | Viewed by 2296

Abstract

Mixed matrix membranes (MMMs) have shown great potential in pervaporation (PV). As for many novel membrane materials however, lab-scale testing often involves synthetic feed solutions composed of mixed pure components, overlooking the possibly complex interactions and effects caused by the numerous other components [...] Read more.

Mixed matrix membranes (MMMs) have shown great potential in pervaporation (PV). As for many novel membrane materials however, lab-scale testing often involves synthetic feed solutions composed of mixed pure components, overlooking the possibly complex interactions and effects caused by the numerous other components in a real PV feed. This work studies the performance of MMMs with two different types of fillers, a core-shell material consisting of ZIF-8 coated on mesoporous silica and a hollow sphere of silicalite-1, in the PV of a real fermented wheat/hay straw hydrolysate broth for the production of bio-ethanol. All membranes, including a reference unfilled PDMS, show a declining permeability over time. Interestingly, the unfilled PDMS membrane maintains a stable separation factor, whereas the filled PDMS membranes rapidly lose selectivity to levels below that of the reference PDMS membrane. A membrane autopsy using XRD and SEM-EDX revealed an almost complete degradation of the crystalline ZIF-8 in the MMMs. Reference experiments with ZIF-8 nanoparticles in the fermentation broth demonstrated the influence of the broth on the ZIF-8 particles. However, the observed effects from the membrane autopsy could not exactly be replicated, likely due to distinct differences in conditions between the in-situ pervaporation process and the ex-situ reference experiments. These findings raise significant questions regarding the potential applicability of MOF-filled MMMs in real-feed pervaporation processes and, potentially, in harsh condition membrane separations in general. This study clearly confirms the importance of testing membranes in realistic conditions. Full article

► Show Figures

Figure 1

11 pages, 2843 KiB

Open AccessArticle

Obtaining Electrospun Membranes of Chitosan/PVA and TiO₂ as a Solid Polymer Electrolyte with Potential Application in Ion Exchange Membranes

by Elio Enrique Ruiz Gómez and Jose Herminsul Mina Hernandez

Membranes 2023, 13(11), 862; https://doi.org/10.3390/membranes13110862 - 27 Oct 2023

Cited by 3 | Viewed by 2209

Abstract

A binary polymeric blend was prepared using chitosan (CS) and polyvinyl alcohol (PVA) at a ratio of 80:20, respectively, to obtain a solid polymeric electrolyte with possible application for the generation of an electric current in proton or anion exchange electrochemical cells. With [...] Read more.

A binary polymeric blend was prepared using chitosan (CS) and polyvinyl alcohol (PVA) at a ratio of 80:20, respectively, to obtain a solid polymeric electrolyte with possible application for the generation of an electric current in proton or anion exchange electrochemical cells. With a 6% m/m solution, a membrane was formed using the electrospinning technique, and the influence of the incorporation of titanium oxide (TiO₂) nanoparticles, at a concentration between 1000 and 50,000 ppm, on the physicochemical properties of the material was evaluated. The micrographs obtained by SEM revealed that the diameter of the nanofibers was close to 100 nm. Likewise, it was found that the incorporation of the nanoparticles affected the moisture absorption of the material, reaching a predominantly hydrophobic behavior in the composite with the highest concentrations of these (2% absorption), while for the lowest content of the filler, the absorption reached values close to 13%. On the other hand, Thermogravimetric Analysis (TGA) showed lower dehydration in the fibrous composite with a 1000 ppm TiO₂ content, while Differential Scanning Calorimetry (DSC) showed that these nanoparticles did not significantly affect the thermal transition (Tm) of the composite. Additionally, with the incorporation of nanoparticles, a shift in the Tg from 44 to 37 °C was found concerning the unfilled binary membrane, which increased the possibility of achieving higher ionic conductivities with the nanocomposites at room temperature. Complex Impedance Spectroscopy determined the material’s activation energy, decreasing this by adding the TiO₂ filler at a concentration of 1000 ppm. On the other hand, when the membranes were doped with a 1 M KOH solution, the fibrous structure of the membrane changed to a porous cork-like configuration. In future research, the electrospun membrane could be used in the development of a composite to validate the energy efficiency of the new solid polymer electrolyte. Full article

(This article belongs to the Special Issue Eco-Friendly Membrane Materials and Technology)

► Show Figures

Figure 1

13 pages, 2617 KiB

Open AccessArticle

Prolonged Anesthesia Effects of Locally Administered Ropivacaine via Electrospun Poly(caprolactone) Fibrous Membranes

by Li Wang, Jiaming Chen, Zicen Li and Fei Guo

Membranes 2023, 13(11), 861; https://doi.org/10.3390/membranes13110861 - 27 Oct 2023

Viewed by 1959

Abstract

Prolonged analgesia is important to safeguard the patient’s comfort and safety during and after surgery in clinical practice. To meet the demand for prolonged analgesia, medical professionals often resort to increasing drug frequency, which may lead to poor patient compliance and serious complications [...] Read more.

Prolonged analgesia is important to safeguard the patient’s comfort and safety during and after surgery in clinical practice. To meet the demand for prolonged analgesia, medical professionals often resort to increasing drug frequency, which may lead to poor patient compliance and serious complications due to drug overdose. Therefore, it is of great interest to develop controlled-release drug delivery systems for local anesthetics, enabling slow and controlled drug release to prolong the analgesic effect and minimize systemic toxicity. In this study, we utilized an electrospinning technique to fabricate nonwoven poly(caprolactone) (PCL) fibrous membranes loaded with Ropivacaine and performed proof-of-principle experiments on both in vitro drug release tests and in vivo animal tests, to further prolong the analgesic effect of Ropivacaine and improve postoperative local pain management and chronic pain treatment. Material characterization and in vitro drug release studies confirmed the feasibility of the Ropivacaine-loaded PCL fibrous membranes for sustained release. The drug loading content and drug loading efficiency of Ropivacaine-loaded fibrous membrane are 8.7 ± 0.3 wt% and 96 ± 3 wt%, respectively. Evaluation in an animal model demonstrated prolonged anesthesia effects along with excellent biocompatibility and stability. At 72 h, the cumulative release accounted for approximately 50% of the drug loading content. This study offers novel approaches and strategies for clinical postoperative pain management and chronic pain treatment, while providing new insights and directions for the design of local anesthetic controlled-release delivery systems. Full article

(This article belongs to the Section Membrane Applications)

► Show Figures

Figure 1

16 pages, 3647 KiB

Open AccessReview

Latest Update on Outer Membrane Vesicles and Their Role in Horizontal Gene Transfer: A Mini-Review

by Beatrice Marinacci, Paweł Krzyżek, Benedetta Pellegrini, Gabriele Turacchio and Rossella Grande

Membranes 2023, 13(11), 860; https://doi.org/10.3390/membranes13110860 - 26 Oct 2023

Cited by 4 | Viewed by 2723

Abstract

Outer membrane vesicles (OMVs) are spherical, lipid-based nano-structures, which are released by Gram-negative bacteria in both in vitro and in vivo conditions. The size and composition of OMVs depend on not only the producer bacterial species but also cells belonging to the same [...] Read more.

Outer membrane vesicles (OMVs) are spherical, lipid-based nano-structures, which are released by Gram-negative bacteria in both in vitro and in vivo conditions. The size and composition of OMVs depend on not only the producer bacterial species but also cells belonging to the same strain. The mechanism of vesicles’ biogenesis has a key role in determining their cargo and the pattern of macromolecules exposed on their surface. Thus, the content of proteins, lipids, nucleic acids, and other biomolecules defines the properties of OMVs and their beneficial or harmful effects on human health. Many studies have provided evidence that OMVs can be involved in a plethora of biological processes, including cell-to-cell communication and bacteria–host interactions. Moreover, there is a growing body of literature supporting their role in horizontal gene transfer (HGT). During this process, OMVs can facilitate the spreading of genes involved in metabolic pathways, virulence, and antibiotic resistance, guaranteeing bacterial proliferation and survival. For this reason, a deeper understanding of this new mechanism of genetic transfer could improve the development of more efficient strategies to counteract infections sustained by Gram-negative bacteria. In line with this, the main aim of this mini-review is to summarize the latest evidence concerning the involvement of OMVs in HGT. Full article

(This article belongs to the Special Issue Recent Advances in Outer Membrane Vesicles)

► Show Figures

Figure 1

14 pages, 517 KiB

Open AccessArticle

Enhancing Palladium Recovery Rates in Industrial Residual Solutions through Electrodialysis

by Pauline Zimmermann, Önder Tekinalp, Øivind Wilhelmsen, Liyuan Deng and Odne Stokke Burheim

Membranes 2023, 13(11), 859; https://doi.org/10.3390/membranes13110859 - 26 Oct 2023

Cited by 1 | Viewed by 1830

Abstract

Palladium is a vital commodity in the industry. To guarantee a stable supply in the future, it is imperative to adopt more effective recycling practices. In this proof-of-concept study, we explore the potential of electrodialysis to enhance the palladium concentration in a residual [...] Read more.

Palladium is a vital commodity in the industry. To guarantee a stable supply in the future, it is imperative to adopt more effective recycling practices. In this proof-of-concept study, we explore the potential of electrodialysis to enhance the palladium concentration in a residual solution of palladium recycling, thus promoting higher recovery rates. Experiments were conducted using an industrial hydrochloric acid solution containing around 1000 mg/L of palladium, with a pH below 1. Two sets of membranes, Selemion AMVN/CMVN and Fujifilm Type 12 AEM/CEM, were tested at two current levels. The Fujifilm membranes, which are designed for low permeability of water, show promising results, recovering around 40% of palladium within a two-hour timeframe. The Selemion membranes were inefficient due to excessive water transport. All membranes accumulated palladium in their structures. Anion-exchange membranes showed higher palladium accumulation at lower currents, while cation-exchange membranes exhibited increased palladium accumulation at higher currents. Owing to the low concentration of palladium and the presence of abundant competing ions, the current efficiency remained below 2%. Our findings indicate a strong potential for augmenting the palladium stage in industrial draw solutions through electrodialysis, emphasizing the importance of membrane properties and process parameters to ensure a viable process. Beyond the prominent criteria of high permselectivity and low resistance, minimizing the permeability of water within IEMs remains a key challenge to mitigating the efficiency loss associated with uncontrolled mixing of the electrolyte solution. Full article

(This article belongs to the Special Issue Advances in Electromembrane Processes for Resource Recovery, 2nd Edition)

► Show Figures

Figure 1

16 pages, 6238 KiB

Open AccessEditor’s ChoiceArticle

High-Performance FAU Zeolite Membranes Derived from Nano-Seeds for Gas Separation

by Qing Wang, Huiyuan Chen, Feiyang He, Qiao Liu, Nong Xu, Long Fan, Chuyan Wang, Lingyun Zhang and Rongfei Zhou

Membranes 2023, 13(11), 858; https://doi.org/10.3390/membranes13110858 - 26 Oct 2023

Cited by 5 | Viewed by 3291

Abstract

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na₂ [...] Read more.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na₂O: 1Al₂O₃: 19 SiO₂: 5000H₂O, the effects of synthesis temperature, crystallization time, and porous support (α-Al₂O₃ or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al₂O₃ support at 368 K for 8 h and had good reproducibility. The H₂ permeance of the membrane was as high as 5.34 × 10⁻⁷ mol/(m² s Pa), and the H₂/C₃H₈ and H₂/i-C₄H₁₀ selectivities were 183 and 315, respectively. The C₃H₆/C₃H₈ selectivity of the membrane was as high as 46, with a remarkably high C₃H₆ permeance of 1.35 × 10⁻⁷ mol/(m² s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and the relatively wide pore size (0.74 nm). Full article

(This article belongs to the Section Membrane Applications)

► Show Figures

Figure 1

21 pages, 5655 KiB

Open AccessArticle

Application of Machine Learning to Characterize the Permeate Quality in Pilot-Scale Vacuum-Assisted Air Gap Membrane Distillation Operation

by Isabel Requena, Juan Antonio Andrés-Mañas, Juan Diego Gil and Guillermo Zaragoza

Membranes 2023, 13(11), 857; https://doi.org/10.3390/membranes13110857 - 26 Oct 2023

Viewed by 1819

Abstract

Membrane distillation (MD) is a thermal desalination technique proposed for the valorization of residual brines that other operations such as reverse osmosis cannot treat. Previous studies have shown that vacuum-assisted air gap (V-AGMD) operation in commercial multi-envelope modules improves the performance of MD [...] Read more.

Membrane distillation (MD) is a thermal desalination technique proposed for the valorization of residual brines that other operations such as reverse osmosis cannot treat. Previous studies have shown that vacuum-assisted air gap (V-AGMD) operation in commercial multi-envelope modules improves the performance of MD noticeably. However, the permeate quality at pilot scale has not been thoroughly characterized so far. The aim of this study is, therefore, to assess and model the effect of the main operating conditions (feed flow rate, inlet temperatures, and feed salinity) on the permeate quality. Results from different steady-state experiments allowed to estimate descriptive metrics such as the salt rejection factor (SRF) and the membrane leak ratio (MLR). Given their non-linear behavior, these metrics were subsequently modeled using artificial neural networks (ANN) to estimate the permeate quality in the whole scope of operating conditions. Acceptable SRF results with MLR values lower than 0.2% confirmed the validity of MD as an operation for the treatment of concentrated brines, although the salinity of the resulting permeate does not comply in all cases with that permitted for human consumption. Full article

(This article belongs to the Special Issue Advances in Modeling, Control, and Optimization of Membrane Distillation and Membrane Separation Processes)

► Show Figures

Figure 1

19 pages, 3856 KiB

Open AccessArticle

Oxyanion Removal from Impaired Water by Donnan Dialysis Plug Flow Contactors

by Shalom Fox, Kristina Stadnik, Amit K. Thakur, Lior Farkash, Zeev Ronen, Yoram Oren and Jack Gilron

Membranes 2023, 13(11), 856; https://doi.org/10.3390/membranes13110856 - 26 Oct 2023

Viewed by 1568

Abstract

In the last twenty-five years, extensive work has been done on ion exchange membrane bioreactors (IEMB) combining Donnan dialysis and anaerobic reduction to remove trace oxyanions (e.g., perchlorate, nitrate, chlorate, arsenate) from contaminated water sources. Most studies used Donnan dialysis contactors with high [...] Read more.

In the last twenty-five years, extensive work has been done on ion exchange membrane bioreactors (IEMB) combining Donnan dialysis and anaerobic reduction to remove trace oxyanions (e.g., perchlorate, nitrate, chlorate, arsenate) from contaminated water sources. Most studies used Donnan dialysis contactors with high recirculation rates on the feed side, so under continuous operation, the effective concentration on the feed side of the membrane is the same as the exit concentration (CSTR mode). We have built, characterized, and modelled a plug flow Donnan dialysis contactor (PFR) that maximizes concentration on the feed side and operated it on feed solutions spiked with perchlorate and nitrate ion using ACS and PCA-100 anion exchange membranes. At identical feed inlet concentrations with the ACS membrane, membrane area loading rates are three-fold greater, and fluxes are more than double in the PFR contactor than in the CSTR contactor. A model based on the nonlinear adsorption of perchlorate in ACS membrane correctly predicted the trace ion concentration as a function of space-time in experiments with ACS. For PCA membrane, a linear flux dependence on feed concentration correctly described trace ion feed concentration as a function of space-time. Anion permeability for PCA-100 was high enough that the overall mass transfer was affected by the film boundary layer resistance. These results provide a basis for efficiently scaling up Donnan dialysis contactors and incorporating them in full-scale IEMB setups. Full article

(This article belongs to the Special Issue Honorary Issue for Prof João G. Crespo)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Membranes, Volume 13, Issue 11 (November 2023) – 36 articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI