Next Article in Journal
Strengthening Mechanism for the Mechanical Properties of Cement-Based Materials after Internal Nano-SiO2 Production
Next Article in Special Issue
3D Composite PDMS/MWCNTs Aerogel as High-Performing Anodes in Microbial Fuel Cells
Previous Article in Journal
A Novel Strategy to Enhance the Photostability of InP/ZnSe/ZnS Quantum Dots with Zr Doping
Previous Article in Special Issue
Two-Dimensional Transition Metal-Hexaaminobenzene Monolayer Single-Atom Catalyst for Electrocatalytic Carbon Dioxide Reduction
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Nanomaterials
Volume 12
Issue 22
10.3390/nano12224049
nanomaterials-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Two-Dimensional (2D) TM-Tetrahydroxyquinone Metal–Organic Framework for Selective CO2 Electrocatalysis: A DFT Investigation

by
Xianshi Zeng
1,2,
Chuncai Xiao
3,
Luliang Liao
2,3,
Zongxing Tu
4,
Zhangli Lai
1,
Kai Xiong
5,6 and
Yufeng Wen
1,*
1
School of Mathematical Sciences and Physics, Jinggangshan University, Ji’an 343009, China
2
Institute for Advanced Study, School of Physics and Materials Science, Nanchang University, Nanchang 330031, China
3
School of Mechanical and Electrical Engineering, Xinyu University, Xinyu 338004, China
4
School of Chemistry and Chemical Engineering, Nanchang University, Nanchang 330031, China
5
Materials Genome Institute, National Center for International Research on Photoelectric and Energy Materials, School of Materials and Energy, Yunnan University, Kunming 650091, China
6
Advanced Computing Center, Information Technology Center, Yunnan University, Kunming 650091, China
*
Author to whom correspondence should be addressed.
Nanomaterials 2022, 12(22), 4049; https://doi.org/10.3390/nano12224049
Submission received: 29 October 2022 / Revised: 14 November 2022 / Accepted: 14 November 2022 / Published: 17 November 2022
(This article belongs to the Special Issue 1D and 2D Nanomaterials for Energy Storage and Conversion)
Browse Figures
Review Reports Versions Notes

Abstract

:
The resource utilization of CO 2 is one of the essential avenues to realize the goal of “double carbon”. The metal–organic framework (MOF) has shown promising applications in CO 2 catalytic reduction reactions due to its sufficient pore structure, abundant active sites and functionalizability. In this paper, we investigated the electrocatalytic carbon dioxide reduction reactions of single-atom catalysts created by MOF two-dimensional coordination network materials constructed from transition metal-tetrahydroxybenzoquinone using density function theory calculations. The results indicate that for 10 transition metals, TM-THQ single levels ranging from Sc to Zn, the metal atom binding energy to the THQ is large enough to allow the metal atoms to be stably dispersed in the THQ monolayer. The Ni-THQ catalyst does not compete with the HER reaction in an electrocatalytic CO 2 reduction. The primary product of reduction for Sc-THQ is HCOOH, but the major product of Co-THQ is HCHO. The main product of Cu-THQ is CO, while the main product of six catalysts, Ti, V, Cr, Mn, Fe, and Zn, is CH 4 . The limit potential and overpotential of Ti-THQ are the highest, 1.043 V and 1.212 V, respectively. The overpotentials of the other monolayer catalysts ranged from 0.172 to 0.952 V, and they were all relatively low. Therefore, we forecast that the TM-HQ monolayer will show powerful activity in electrocatalytic carbon dioxide reduction, making it a prospective electrocatalyst for carbon dioxide reduction.

1. Introduction

From the industrial revolution onwards, the excessive use of fossil fuels has resulted in a significant rise in the concentration of carbon dioxide (CO 2 ) in the atmospheres, which could lead to devastating outcomes for the modern world. The conversion of carbon dioxide into useful chemical raw materials can help to ease environmental issues including the “greenhouse effect” and conventional methods’ reliance on fossil raw materials such as crude oil [1,2,3]. Therefore, CO 2 -based conversion reactions have received a lot of attention. CO 2 reduction reaction is one of the typical representatives, which can directly obtain C 1 -C 3 high value-added chemical products (such as CO, CH 4 , HCOOH, HCOH, CH 3 OH, C 2 H 4 , C 2 H 6 , C 2 H 5 OH, C 3 H 6 , etc.) through electrochemistry [4,5], chemical reforming [6], photochemistry [7], biochemistry [8], etc. Among them, electrocatalytic reaction conditions are milder, and the process is the high cleanliness of the process is of great practical importance. However, this technology also faces the problems of low catalytic efficiency, limited yield and insufficient catalyst life, so there is an urgent need to devise and fabricate new catalysts with high efficiencies and low overheads.
A crystal structure known as a metal–organic framework (MOF) is made up of inorganic metal ions and organic ligands. It can be made using a bottom–up assembly method under solvothermal conditions and has the advantages of having an extremely diverse structural makeup, being highly porous, and having a high specific surface area [9,10,11,12,13,14], thus showing excellent performance in sensing, separation, energy storage, and other fields, especially in the field of catalysis [15,16,17,18,19,20,21,22,23,24]. MOFs have the following advantages over conventional catalytic materials: (1) The porous characteristics provide a rich particular surface area for reaction, which promoted the adsorption of reactants. (2) The confinement of pore channels produces effects such as spatial and electron limitation, optimizing reaction intermediates and selectivity [25]. (3) The metal centers, as catalytic active sites, can be uniformly distributed on the internal and external surfaces of the material at the atomic level. This usually results in higher catalytic efficiency than conventional catalysts with active sites concentrated on the external surface. (4) The metal centers and ligands are matched electronically to form a characteristic energy band structure, and some MOFs have certain electrical conductivity, which is suitable for the absorption and transmission of electrical energy. (5) The well-defined crystalline configuration of MOF can help to study the reaction mechanism and establish the correspondence between structure and catalytic performance. In addition, the high affinity of MOF for CO 2 greatly enhances the correlation between reactants and catalysts, which promotes the efficient reaction. Therefore, MOF has become one of the popular materials at the frontier of CO 2 electrocatalytic reduction. In recent years, several researchers have conducted extensive work on MOF electrocatalytic CO 2 reduction. For instance, Zhu et al. [26] presented a strategic approach for the in situ electrosynthesis of hollow copper MOF and its reduction to a multistage Cu dendrimer catalyst in a reaction in which the Cu-MOF film was prepared in 5 min. The Cu dendrimer catalyst obtained by this strategy has a high surface area with an open reactive site, which is favorable for the reduction of CO 2 to formate. In the electrolyte of the ionic liquid, the current density of the system was up to 102.1 mA/cm 2 and the selectivity was 98.2%. Kang et al. [27] used copper foam as a substrate to control the MOF growth kinetics by using a ligand with high spatial site resistance, resulting in the rapid growth of Cu-MOF with a large number of defects on copper foam. The catalyst was able to reduce CO 2 to formate in an acetonitrile ionic liquid electrolyte with a Faraday efficiency of 90.5%. In addition, other researchers have constructed MOFs by ligand doping, which have also shown excellent performance for electrocatalytic CO 2 reduction [28,29]. More interestingly, conductive materials facilitate charge transport and are more advantageous in electrocatalysis. In a mixed electrolyte of 1 mol/L choline chloride and 1 mol/L potassium hydroxide, Majidi et al. [30] created a copper-based, conductive, two-dimensional MOF: copper-tetrahydroxyquinone (Cu-THQ) nanosheets, which required only a low overpotential of 16 mV for CO 2 reduction. The catalytic activity was excellent. The current density was around 173 mA/cm 2 , and the average CO Faraday efficiency was approximately 91% at an applied voltage of −0.45 V (with respect to the reversible hydrogen electrode). Their great progress in the laboratory inspired us to explore the application of TM-THQ electrocatalytic CO 2 reduction in depth. Here, we have constructed a series of TM-THQ metal–organic framework materials with 3D transition metals and conducted a systematic study by DFT in CO 2 electrocatalytic reduction reactions, where computational simulations are performed to screen possible pathways for cost-effective novel catalysts.

2. Details of The Calculation

Using spin-polarized density generalized function theory (DFT), the Dmol3 package was used for all computations in this study [31]. Under the generalized gradient approximation, the Perdew–Burke–Ernzerhof (PBE) function describes the exchange correlations between electrons (GGA) [32]. The DNP basis group is used in conjunction with the effective potential DSPP approximation to address the basis group, which substitutes the kernel electron with a single effective potential and incorporates relativistic corrections [33]. A van der Waals correction (DFT-D2) was included to the computations to better explain the adsorption of molecules on the surface due to the weak long-range interactions between the layers [34,35,36,37]. The conductor approximation shielding model (COSMO) was used as the solventization model since the real catalytic process takes place in an aqueous environment. This choice improved agreement with the experiment. The water (relative permittivity ϵ = 78.54) was used as the solvent to simulate the effect of the solvent on all systems [38]. The interaction between adjacent heterogeneous joints was eliminated by selecting a vacuum layer thickness of 25. The Monkhorst–Pack method [39] K-point grid with 2 × 2 × 1 and 6 × 6 × 1 are used for the structural determination and electronic structure calculations, respectively. To increase the computational accuracy, the energy convergence criterion is 10 − 6 eV.
For the purpose of discussing the strength of the interactions between intermediates and THQ monolayers, Equation (1) provides a defined energy of adsorption (Eads) (as exemplified by the adsorption energy of CH 4 ).
E a d s = E T M − T H Q − C H 4 − E T M − T H Q − E C H 4
where E T M − T H Q − C H 4 , E T M − T H Q and E C H 4 denote the sum energy of CH 4 that is adsorbed on the surface of TM-THQ, the sum energy of the TM-THQ unilayer and the sum energy of individual CH 4 molecules, respectively. Since CO 2 RR is characterized by a large number of reaction paths, the notion of Gibbs free energy was introduced to enable the determination of the most suitable reaction path. When the reaction involves the transfer of electrons, the energy of the reaction can be calculated by the standard electrode model for hydrogen presented by Nørskov and coworkers [40,41,42]. Equation (2) is the equation for the Gibbs free energy.
Δ G = Δ E + Δ E Z P E − T Δ S + Δ G p H + Δ G U
where Δ E is a reaction energy of the reaction, Δ E Z P E and Δ S is the change in zero-point energies and entropy values. Here, T is the reaction’s thermodynamic temperature (298.15 K). Δ G p H is the free energy correction ( Δ G p H = 2.303 k B T p H ) introduced by the different acidity of the solution (different H+ concentrations), assuming a p H of 0 in acidic solutions. While Δ G U is the free energy correction brought about by the various electrode potentials, Δ G U may be calculated using Equation (3) as follows:
Δ G U = − n e U
where U is the applied electrode potential and n is the total number of transferred electrons. When determining if the catalyst has great catalytic activity, the limiting potential ( U L ) and overpotential ( η ) are crucial considerations. The limiting potential is calculated from Equation (4).
U L = − Δ G m a x / n e
Δ G m a x is the value of the change in the free energy of the decisive step. The over-potential can be derived by computing the differential between the equilibrium potential (Uequilibrium) and the limiting potential and the limiting potential obtained as the difference shown in Equation (5).
η = U e q u i l i b r i u m − U L

3. Results and Discussion

3.1. The Structural Characteristics and Features of TM-THQ Monolayer

The structure of the MOF material constructed by TM-THQ is shown in Figure 1. Here, (a) and (b) are, respectively, the top and side views of a single cell, and (c) is a top view of a 2 × 2 supercell. The specific lattice constant values of these ten MOF materials after optimization are presented in Table S1. The top view of the monocell clearly shows that each monocell contains 12 C atoms, 12 O atoms, and 3 transition metal atoms, and that each metal atom is coordinated to 4 O atoms in the tetrahydroxybenzoquinone. Each atom of the 10 transition metals (from Sc to Zn) we considered resides in the same plane (Figure 1). The bond lengths between metal atoms and their nearest O atoms are in the range of 1.858 to 2.066 Å (Figure 2). The bond length of Sc-O is 2.066 Å, which is consistent with the fact that Sc has the largest atomic radius among the 10 metals. Furthermore, in order to study the electronic state of the monolayer, we performed a Hirshfeld charge analysis, and it can be seen from Table 1 that all the metal atoms in the 10 metals of the first transition metal series considered have a partial positive charge, while the nearest O atom has an opposite negative charge, which indicates that the metal atoms transfer some of their electrons to the THQ monolayer, making the metal atoms and O atoms interact with each other as ionic bonds in addition to ligand bonds. The analysis of the spin states of the metal atoms shows that Cr exhibits a spin state with a magnetic moment of 2.977 μ B , while the rest of the metal atoms are in the non-spin state.

3.2. The Stabilization of TM-HQ Single Layer

The stability is an essential parameter for evaluate the catalytic performance of catalysts. To investigate the stability of the TM-THQ monolayer, we have calculated the cohesion values of the bulk metal and the binding values of the TM-THQ monolayer. The cohesion energy can be obtained by the equation: E c = ( E T M ( b u l k ) − n E T M ) / n , where E M ( b u l k ) and E T M are the energies of the bulk and individual metal atoms, respectively. The number of n is the number of metal atoms in the volume. The binding energy is calculated by the equation: E b = E T M − P c − E T M − E P c , where E T M − P c , E T M and E P c are the energies of TM-Pc monolayer, individual metal atoms and phthalocyanine monolayer, respectively. For single-atom accelerators, the stronger the binding ability between the metal atoms and the substrate, the more difficult it is for the metal atoms to agglomerate with each other; this results in a uniform and stable mosaic of metal atoms on the substrate. Table S2 gives the binding energy and the cohesion energy of the corresponding metals for these ten TM-THQ catalysts. The cohesion energies of the bulk metal parts are in the range of −6.578 to −1.054 eV, while the binding energies in the case of transition metal atoms and tetrahydroxyquinone monolayer are in the range of −11.045 to −4.628 eV.
It is obvious from Figure 3 that the cohesion energy of the metal bulk is below the binding energy of the corresponding metal TM-HTQ monolayer, which indicates that the metal atoms tend to bind to the tetrahydroxyquinone monolayer more than the metal atom agglomeration, thus making the metal atoms uniformly mosaic into the cavities of the tetrahydroxyquinone monolayer, and thus, the TM-HTQ monolayer has good stability. Meanwhile, the binding energy between these 10 transition metals (from Sc to Zn) and the tetrahydroxybenzoquinone monolayer shows a gradual increasing trend and weakening bond solidity. This is because the oxygen atom is a strong non-metallic atom, while Sc to Zn are of the same period, and the metallicity gradually decreases. Generally speaking, the stronger the metallicity, the stronger the bonding with the surrounding oxygen atoms, and conversely, the weaker the metallicity, the weaker the bonding with the oxygen atoms, thus showing a gradual increase in the bonding energy. The reason for the irregular fluctuations of the cohesion energy of the ten metals is that the ten transition metals belong to different crystal systems, among which Sc, Ti, Co, and Zn belong to a hexagonal structure; V, Cr, Fe, Ni, and Cu belong to a cubic crystal system structure, and Mn belongs to a trigonal crystal system structure. Different crystal systems have different atomic arrangements, which affect different ground state energies and thus exhibit irregular fluctuations.

3.3. TM-THQ Single Layer for CO 2 RR and HER Specificity

Generally, electrocatalytic CO 2 reduction takes place in solution as a multiple electron step process. The proton–electron pairs (H+ + e−) in solution are increasingly involved in the reaction under the action of external voltage, and after the molecules of carbon dioxide are adsorbed on the surface of the catalyst, two separate intermediates are produced during the first protonation step, depending on the position of the added H. If H is included in the oxygen atom (* + CO2 + H+ + e− → *COOH ), the intermediate *COOH will be obtained. Conversely, if H is included in the carbon atom (* + CO2 + H+ + e− → *OCHO), the intermediate *OCHO will be developed. However, H can be also added to the metal atom in the catalyst (* + H+ + e− → *H), resulting in a hydrogen precipitation reaction (HER), which is undesirable for CO 2 RR. In fact, the two reactions, CO 2 RR and HER, are in competition, so for CO 2 RR catalysts, we have to consider the material selectivity for CO 2 RR and HER.
Figure 4 compares the variations of *OCHO, *COOH and *H Gibbs free energies formed by the first-step protonation reaction. As shown in Figure 4, without considering the HER reaction, the first transition metal series of Mn, Fe, Co, Ni, and Cu are more likely to form intermediates *COOH, while Cr, V, Ti, Sc, and Zn are more likely to form intermediates *OCHO. When considering the competition with HER, it is obvious that for both Cu-THQ and Zn-THQ catalysts, the Gibbs free energy is lower than that of *H, regardless of whether *COOH or *OCHO intermediates are formed, showing a good inhibition of HER reaction and good electrocatalytic CO 2 reduction activity. For Ni-THQ catalysts, the formation energy is higher than that of *H, regardless of whether *COOH or *OCHO intermediates are formed, which indicates that once the active site receives protons to generate *H, mainly hydrogen precipitation reaction occurs, and thus, it can be concluded that Ni-THQ does not compete with the HER reaction for CO 2 electrocatalysis.
In addition, from Figure 4, it can be seen that the Gibbs free energy formed of *OCHO intermediates is higher than that for the formation of *H for the metals Mn, Fe, and Co, but the Gibbs free energy for the generation of *COOH intermediates is lower than that for the generation of *H. For the metals V, Ti, and Sc, the formation energy for the obtained of *COOH intermediates is also higher than that for the obtained of *H, but the production of *OCHO intermediates with Gibbs free energy is lower than at the time for the production of *H. Once the active site of the metal is occupied by O*CHO or C*OOH, there is no excess active site to accept H*. Therefore, it can be concluded that the six catalysts Mn, Fe, Co, V, Ti, and Sc are also catalytically active for the CO 2 RR reaction.

3.4. Potential Product Routes and Adsorbed Energy

Owing to TM-THQ electrocatalytic CO 2 reduction is a single-atom catalytic procedure, it is widely assumed that it is difficult to produce poly-carbon products because the monoatomic catalytic process cannot achieve C–C coupling between intermediates. Therefore, theoretically, the single-atom catalytic CO 2 reduction process is predicted as long as the C 1 productos is considered. The most common C 1 products in the electrocatalytic reduction of carbon dioxide are CO, CH 4 , HCOOH, CH 3 OH, and HCHO. Figure 4 shows the scheme of electrocatalytic reduction of CO 2 to obtain C 1 products [43].
As can be seen in Figure 5, the reduction of CO 2 to produce CO, HCOOH is a 2e process. The reduction paths are CO2 → *COOH → *CO → CO and CO2 → *OCHO → *OCHOH → HCOOH. The generation of HCHO is a 4e process, and the reduction paths are CO2 → *COOH → *CO → *CHO → *OCH2 → HCHO. The acquisition of CH 3 OH products is a 6e process, and the reduction paths are CO2 → *COOH →*CO → *CHO → *OCH2 → *OCH3 → *OHCH3 → CH3OH. The most complicated is the obtaining of the CH4 product, which is an 8e process with three possible paths, namely: (1) CO2 → *COOH → *CO → *COH → *C → *CH → *CH2 → *CH3 →* + CH4; (2) CO2 → *COOH → *CO → *CHO → *OCH2 → *OCH3 → *OHCH3 → *O + CH4 → *OH → H2O and (3) CO2 → *COOH → *CO → *CHO → *OCH2 → *OCH3 → *OHCH3 → *OH + CH4 → * + H 2 O.
In order to predict the most likely product for each catalyst based on the complexity of the CO 2 electrocatalytic reduction reaction pathway, we first calculated the adsorption energy of the catalyst for the C 1 product, as shown in Table 2.
As can be seen in Table 2, Sc, Co as well as Cu have a weak adsorption capacity for all five C 1 products and can be obtained by smooth desorption from the catalyst surface once the products are generated. Although Ni exhibits the same weak adsorption capacity for the five C 1 products, it is mainly manifested as an HER reaction process according to Figure 3 and thus is not considered. For the three single-atom catalysts, Ti, V and Cr, they have a strong adsorption capacity for CO, HCOOH, HCHO and CH 3 OH, and therefore, these products are firmly adsorbed in the catalysts and cannot be desorbed, leading to the poisoning of the catalytic process to obtain the products. Fortunately, the adsorption capacity for CH 4 is not strong, thus making it possible to obtain the CH 4 products. The C 1 products that can be desorbed from the surface of Mn-THQ are HCOOH, HCHO, and CH 4 . The Zn-THQ catalyst is strongly adsorbed for CH 3 OH, and this product cannot be obtained, but the other four C 1 products are not strongly adsorbed, and thus, CO, HCOOH, HCHO, and CH 4 can be obtained.

3.5. The Reaction Route of Electro-Chemical Reduction of Carbon Dioxide

3.5.1. HCOOH as the Main Catalytic Product

According to the scheme in Figure 5, the first-step protonation of CO 2 after the adsorption of Sc-THQ occurs in the presence of external electricity potential to form *COOH or *OCHO intermediates. However, according to Figure 4, it can be seen that the Sc-HQ catalyst requires crossing a relatively high energy bar for the formation of *COOH intermediates in the first step of protonation, and the competitive reaction with HER shows weakness; thus, we only consider the generation of an *OCHO intermediate step in the electrocatalytic CO 2 reduction process.
As can be seen from Figure 6, the generation of *OCHO intermediate is a Gibbs free energy drop process and the reaction is easy to proceed, and the second paper protonation step occurring on this basis to generate *OCHOH intermediate is also a free energy drop process. Then, after the formation of *OCHOH, this intermediate has the potential to undergo a *OCHOH → H+ + e−) → *CHO/*OCH + H2O protonation reaction, but it needs to cross the energy barrier of 1.289/1.677 eV. In contrast, the direct desorption of *OCHOH to form HCOOH requires crossing only an energy barrier of 0.816 eV. The detailed values of the free energy are given in Table S4. Thus, HCOOH desorption prevails overwhelmingly, and the product is obtained while the reduction reaction is terminated. The reaction path of the whole process is * + CO2 → *OCHO →*OCHOH → HCOOH where the rate-determining step is *OCHOH → * + HCOOH and the limiting potential is 0.816 V.

3.5.2. HCHO Is the Main Catalytic Product

We found that for the Co-THQ catalyst, the main product is HCHO. Figure 7 shows the step diagram for each step of Co-THQ electrocatalytic CO 2 reduction. Detailed values of the Gibbs free energy change at every protonation step are displayed in Table S5. According to Figure 4, the Co-THQ catalyst needs to require crossing a high energy bar in the first step of protonation to form a *OCHO intermediate, and the competitive reaction with HER shows weakness; thus, we only consider the step of generating *COOH intermediate in the electrocatalytic CO 2 reduction process. As can be seen from Figure 7, after the adsorption of CO 2 molecules onto the surface of Co-THQ, the first step of protonation to form *COOH is a free energy rise process, which requires overcoming an energy barrier of 0.242 eV. The second step of protonation to form *CO intermediates is also a free energy rise process, but the energy barrier to be overcome is relatively small, with a value of 0.179 eV. After the formation of *CO intermediates, further protonation to form *CHO/*COH is possible, and CO desorption may also occur to obtain CO products. However, according to Table S5, it can be seen that the formation of *COH as well as CO desorption requires overcoming a higher energy barrier of 1.294 eV and 0.528 eV, respectively, while the formation of *CHO is a free energy drop process. Thus, we consider this step as the formation of *CHO. Further protonation to form *OCH 2 is also an exothermic reaction with a free energy drop. After the formation of *OCH 2 intermediate, further protonation to form *OCH 3 requires crossing a higher energy barrier of 0.533 eV, while HCHO desorption only requires overcoming an energy barrier of 0.196 eV. Therefore, HCHO desorption occurs at this step to obtain the product and terminate the reaction. The whole process of HCHO product generation is * + CO2 → *COOH → *CO → *CHO → *OCH2 → HCHO. The rate-determining step is * + CO2 + H+ + e−) → *COOH, and the corresponding limiting potential is 0.242 V.

3.5.3. With CH 4 as the Main Catalytic Product

From the adsorption energies in Table 2, it is clear that the MOF materials constructed with three atoms of Ti, V and Cr and tetrahydroxybenzoquinone have strong adsorption of CO, HCOOH, HCHO and CH 3 OH, and the products cannot be obtained by desorption. When these three metal-tetrahydroxybenzoquinones were used as electrocatalytic CO 2 reduction, only CH 4 products were obtained. Gibbs free energy calculations after the protonation step showed that the main products obtained by the electrocatalytic CO 2 reduction of Mn, Fe, and Zn atoms were also CH 4 . The free energy step curves for each protonation step of these six catalysts are given in Figure 8.
From Figure 4, it can be seen that the energy barrier to be crossed in the first step of protonation to form *COOH in the electrocatalytic CO 2 reduction process of both Ti and V atoms is high and cannot compete with HER. Therefore, we only consider the formation of the *OCHO intermediate step in the first step of the protonation process. Figure 8a shows Ti-THQ and Figure 8b shows the step diagram of the V-THQ electrocatalytic CO 2 reduction process. The two atom-catalyzed processes are similar, and the formation of *OCHO intermediates is an exothermic reaction as a free energy drop process. The further protonation process to form *OCHOH also shows a free energy drop and is prone to reaction. After *OCHOH formation, the further protonation process of both atoms has a higher energy barrier for the formation of *OCH than for the formation of *CHO, and thus, the formation of *OCH intermediates is not considered. In the subsequent *CHO → *OCH2 → *OCH3 → *O/*CH3OH → *OH are both free energy decreasing processes, but in the final 8e process they are both free energy increasing processes, 0.473 eV (see Table S6) and 0.241 eV (see Table S7), respectively. Therefore, the main products of both Ti and V atomic electrocatalytic CO 2 reduction are CH 4 , and the rate decisive steps are *OCHOH + H+ + e−) → *CHO + H2O, but the corresponding limiting potentials are different, with 1.043 eV for Ti-THQ and 0.663 eV for V-THQ. It is obvious that the electrocatalytic performance of V-THQ is due to Ti-THQ.
Although the adsorption energy of Cr-THQ for C 1 products behaves in line with Ti and V, and only CH 4 can be obtained by desorption from the catalyst surface, the Gibbs free energy of Cr-THQ for the *COOH/*OCHO formation in the first protonation step is below that for the formation of *H according to Figure 4, which shows a good inhibition of hydrogen precipitation reaction. Figure 8c shows the free energy step diagram of the Cr-THQ electrocatalytic CO 2 reduction process. Table S8 shows the Cr-THQ electrocatalytic CO 2 reduction protonation steps and the corresponding free energy changes. In the first step, protonation to form *COOH/*OCHO consists of free energy reduction processes, and the subsequent protonation to form *CO/*OCHOH also consists of free energy reduction processes. In the next step, *CO/*OCHOH → *COH needs to cross a higher energy barrier of 1.488 eV and 1.622 eV, respectively (see Table S8), while the energy barrier for the formation of *CHO is lower. Thus, in this step, we only consider the *CHO intermediate, where the energy barrier of the *CO → *CHO process is 0.211 eV, which is slightly lower than that of *OCHOH → *CHO at 0.254 eV (Table S8). In the subsequent protonation steps, almost all of them are free energy reduction processes, except that the energy barrier of 0.032 eV needs to be crossed in the 8e process. Therefore, we believe that the main product of Cr-THQ electrocatalytic CO 2 reduction is CH 4 , and the decisive step is: *CO + H2O + H+ + e−) → *CHO + H2O, with the corresponding limiting potential of 0.211 eV.
According to Figure 4, the energy barrier to be crossed in the first step of protonation to form *OCHO in the electrocatalytic CO 2 reduction process of both Mn and Fe atoms is high and cannot compete with HER. Therefore, we only consider the formation of the *COOH intermediate step in the first protonation step. Figure 8d shows Mn-THQ, and Figure 8e shows the step diagram of the Fe-THQ electrocatalytic CO 2 reduction process. Tables S9 and S10 show the Mn-THQ and Fe-THQ electrocatalytic CO 2 reduction protonation steps and the corresponding free energy changes, respectively. The two atom-catalyzed processes are similar in that the formation of the *COOH intermediate is an exothermic reaction with decreasing free energy. The further protonation process to form *CO also exhibits a free energy drop and is readily reactive. After *CO formation, both atomic further protonation processes exhibit a higher energy barrier for the formation of *COH than for the formation of *CHO, and thus, the formation of *COH intermediates is not considered. After the formation of *OCH 2 intermediates, both catalysts are relatively difficult to desorb to generate HCHO, and the energy barriers to be overcome for Mn-THQ and Fe-THQ are 1.105 eV (see Table S9) and 0.716 eV (see Table S10), respectively, so that HCHO need not be considered as a product to desorb. Therefore, the main products of both Mn and Fe monoatoms are CH 4 . The rate-determining steps are *CO + H2O + H+ + e−) → *CHO + H2O and *CHO + H2O + H+ + e−) → *OCH2 + H2O, corresponding to the ultimate potentials are 0.145 V and 0.147 V, respectively.
The free energy step diagram for each intermediate step of the Zn-THQ electrocatalytic CO 2 reduction is shown in Figure 8f. Table S11 shows the reaction equations of each protonation step of Zn-THQ and the corresponding Gibbs free energy changes. Figure 8f shows that the first step of protonation to form *COOH/*OCHO are both free energy step-up processes, which need to overcome the barriers of 0.783 eV and 0.307 eV, respectively. The subsequent formation of *CO/*OCHOH consists of free-energy lowering processes. However, among the subsequent steps, only the *CO → *CHO step requires a smaller energy barrier to be overcome and is the main step that occurs. Unfortunately, the energy barrier that needs to be overcome for the HCOOH desorption step is 0.841 eV (Table S11), which is higher than the energy barrier of 0.783 eV for the formation of *COOH, and thus, the first step of protonation to form *OCHO need not be considered. The main product of Zn-THQ electrocatalytic CO 2 reduction is CH 4 , and the reaction path is: * + CO2 → *COOH → *CO → *CHO → *OCH2 → *OCH3 → *CH3OH → *OH → * + H2O. The reaction rate-determining step is * + CO2 + H+ + e−) → *COOH, which corresponds to a limiting potential of 0.783 V.

3.5.4. Carbon Monoxide Is the Main Catalytic Product

Figure 9 shows the Cu-THQ free energy steps for each step of the protonated carbon dioxide reduction. The reaction equations and the corresponding Gibbs free energy variations for each protonation step are shown in Table S12. After carbon dioxide is attracted to the Cu-HQ surface, the protonation reduction reaction proceeds in the presence of an external voltage. It can be seen in Figure 9 that the first step of protonation to form *COOH requires overcoming a lower energy barrier, and therefore, the formation of *COOH intermediates dominates. The second step of protonation to form *CO is a free energy reduction process. After *CO formation, the formation of *CHO/*COH by possible further protonation requires overcoming an energetic barrier of 0.767 eV/1.897 eV (Table S12), whereas the step where CO desorption occurs to obtain the product only requires the overcoming of an energetic barrier of 0.65 eV (Table S12). Therefore, the reaction *CO + H2O → * + CO + H2O dominates to obtain the product of CO and terminate the reaction. The reaction path of the whole process is * + CO2 → *COOH → *CO → CO. The step that determines the rate is * + CO2 + H+ + e−) → *COOH, which corresponds to a potential limit of −0.888 V.

3.6. Electronic Structure Analysis

Following the Gibbs free energy change for each intermediate step in Section 3.5, we discuss the rate-determining step, the limiting potential, and the corresponding major products for each catalyst. Among the ten 3D transition metal elements, the Ni-HTQ catalysts for electrocatalytic CO 2 in solution indicate that the HER reaction is absolutely dominant. The primary reduction product of Sc-THQ is HCOOH. The main product of Co-THQ is HCHO. The main product of Cu-THQ is CO. The main products of the six elements Ti, V, Cr, Mn, Fe, and Zn are CH 4 .
The rate-determining steps, limiting potentials and overpotentials of these nine metal-catalyzed processes are given in Table 3. Ti-HQ has the highest limiting and overpotential of 1.043 V and 1.212 V, whereas the overpotentials of the other monolayer catalysts are between 0.172 and 0.952 V, which is comparable to the surface of the most active step Cu(211) ( η = 0.77 V) and the surface of the metal Pt(111) ( η = 0.46 V) [44]. Thus, our results of theory suggest a very prospective single-atom catalyst for electrocatalytic CO 2 abatement.
Organometallic catalysts with metal–ligand bonding theory suggest that the interaction between catalyst and intermediate is mainly σ - and π -bonds. Figure 10 shows a clear overlap between the 3D orbits of metallic atoms and the 2p orbits of O or C atoms in the determining step intermediates (*OCHOH,*CO,*CHO or *COOH), either spinning up or spinning down, which indicates a good interaction between the TM-HQ monolayer and the intermediate. All these TM-THQs have non-zero electronic density of states at the Fermi energy level and exhibit metallicity, with the most obvious metallicity of Cr and Mn. However, the overlap effect of the 3D and 2P orbitals in Figure 10a–c is better than that of the 3D and 2P orbitals in Figure 10e–g). This indicates a stronger interaction of Sc, Ti and V with the respective intermediates than that of Cr, Mn and Fe. The stronger the interaction, the more stable the adsorption intermediate system is and the higher the energy barrier that needs to be overcome to ensure the catalytic reaction, which leads to a larger increase in the free energy of the decisive step of the Ti-THQ-catalyzed CO 2 reduction, resulting in a more negative limiting potential for the reduction reaction. As can be seen in Table 3, the limiting potentials U L for the Sc-THQ, Ti-THQ, and V-THQ electrocatalytic CO 2 reduction are 0.816 eV, 1.043 eV, and 0.633 eV, respectively, which are higher than those of the Cr, Mn, and Fe catalysts. This is very consistent with the results of PDOS. In addition, the limiting potential of Co is 0.242 V, which is lower than that of Cu and Zn. The overlap effect of 3D orbitals and 2P orbitals in Figure 10g is better than that in Figure 10h,i, which indicates that Co has stronger interaction with *COOH than Cu and Zn and exhibits a more stable structure. Thus, the energy barrier to be crossed for the formation of *COOH by the first step of protonation after CO 2 adsorption on the surface of Co-THQ is lower than that of Cu and Zn.

4. Conclusions

In the present work, electrocatalytic CO 2 reduction reactions with single-atom catalysts creating from transition metal-tetrahydroxyquinone two-dimensional ligand networking materials are investigated. Density functional theory measurements show that metallic atom binding energies to THQ are large enough for 10 transition metal TM-THQ monolayers ranging from Sc to Zn to allow the stable dispersion of metal atoms in the THQ monolayer.The Ni-THQ catalyst does not compete for HER reactions during electrocatalytic CO 2 reduction. The major reduction product of Sc-THQ is HCOOH, and the major product of Co-THQ is HCHO. The main product of Cu-THQ is CO. The main product of six elements, Ti, V, Cr, Mn, Fe and Zn, is CH 4 . Ti-THQ has the highest limiting potential and overpotential of 1.043 V and 1.212 V, respectively, while the overpotential of other monolayer catalysts ranges from 0.172 to 0.952 V, all of which are relatively low. Therefore, we predict that the TM-THQ monolayer will show great catalysis activities in the electocatalytic CO 2 reduction process, making it a promising electrocatalyst for CO 2 reduction.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/nano12224049/s1, Table S1. Lattice constant a and b of TM–THQ in Å, where TM are the metal atoms of the first transition metal series; Table S2. E c is the cohesive energy of the bulk TM, E b is the binding energy between the TM and the TM–THQ, where TM are the metal atoms of the first transition metal series; Table S3. Gibbs free energy change ( Δ G /eV) of the first protonation step in the CO 2 reduction reaction (CO 2 RR) and H 2 evolution reaction (HER) on the TM–THQ; Table S4. Gibbs free energy change for ench protonation step of Sc-THQ electrocatalytic CO 2 reduction; Table S5. Gibbs free energy change for each protonation step of Co-THQ electrocatalytic CO 2 reduction; Table S6. Gibbs free energy change for each protonation step of Ti-THQ electrocatalytic CO 2 reduction; Table S7. Gibbs free energy change for ench protonation step of V-THQ electrocatalytic CO 2 reduction; Table S8. Gibbs free energy change for each protonation step of Cr-THQ electrocatalytic CO 2 reduction; Table S9. Gibbs free energy change for each protonation step of Mn-THQ electrocatalytic CO 2 reduction; Table S10. Gibbs free energy change for each protonation step of Fe-THQ electrocatalytic CO 2 reduction; Table S11. Gibbs free energy change for each protonation step of Zn-THQ electrocatalytic CO 2 reduction; Table S12. Gibbs free energy change for each protonation step of Cu-THQ electrocatalytic CO 2 reduction.

Author Contributions

Conceptualization, X.Z. and Y.W.; methodology, C.X. and Z.L; software, K.X. and Y.W.; validation, X.Z., C.X. and Y.W.; formal analysis, Z.T. and K.X.; investigation, Z.T. and Z.L.; data curation, L.L. and C.X.; writing—original draft preparation, X.Z., C.X.; writing—review and editing, Z.T., Z.L. and Y.W.; visualization, X.Z., C.X. and Y.W.; project administration, C.X., L.L. and Y.W.; funding acquisition, C.X., L.L. and Y.W.; All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the National Natural Science Foundation of China (grant numbers 12064019 and 51661013), and Science and Technology Program of Education Office of Jiangxi Province(grant numbers GJJ212326 and GJJ202321).

Data Availability Statement

The data presented in this study are available in Supplementary Material.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Zhang, E.; Wang, T.; Yu, K.; Liu, J.; Chen, W.; Li, A.; Rong, H.; Lin, R.; Ji, S.; Zheng, X.; et al. Bismuth single atoms resulting from transformation of metal–organic frameworks and their use as electrocatalysts for CO2 reduction. J. Am. Chem. Soc. 2019, 141, 16569–16573. [Google Scholar] [CrossRef] [PubMed]
  2. Zhao, C.; Dai, X.; Yao, T.; Chen, W.; Wang, X.; Wang, J.; Yang, J.; Wei, S.; Wu, Y.; Li, Y. Ionic Exchange of Metal-Organic Frameworks to Access Single Nickel Sites for Efficient Electroreduction of CO2. J. Am. Chem. Soc. 2017, 139, 8078–8081. [Google Scholar] [CrossRef]
  3. Nguyen, D.L.T.; Kim, Y.; Hwang, Y.J.; Won, D.H. Progress in development of electrocatalyst for CO2 conversion to selective CO production. Carbon Energy 2020, 2, 72–98. [Google Scholar] [CrossRef] [Green Version]
  4. Ye, L.; Liu, J.; Gao, Y.; Gong, C.; Addicoat, M.; Heine, T.; Wöll, C.; Sun, L. Highly oriented MOF thin film-based electrocatalytic device for the reduction of CO2 to CO exhibiting high faradaic efficiency. J. Mater. Chem. 2016, 4, 15320–15326. [Google Scholar] [CrossRef]
  5. Deng, P.; Yang, F.; Wang, Z.; Chen, S.; Zhou, Y.; Zaman, S.; Xia, B.Y. Metal–Organic Framework-Derived Carbon Nanorods Encapsulating Bismuth Oxides for Rapid and Selective CO2 Electroreduction to Formate. Angew. Chem. 2020, 132, 10899–10905. [Google Scholar] [CrossRef]
  6. Graciani, J.; Mudiyanselage, K.; Xu, F.; Baber, A.E.; Evans, J.; Senanayake, S.D.; Stacchiola, D.J.; Liu, P.; Hrbek, J.; Sanz, J.F.; et al. Highly active copper-ceria and copper-ceria-titania catalysts for methanol synthesis from CO2. Science 2014, 345, 546–550. [Google Scholar] [CrossRef]
  7. Ouyang, T.; Huang, H.H.; Wang, J.; Zhong, D.C.; Lu, T. A Dinuclear Cobalt Cryptate as a Homogeneous Photocatalyst for Highly Selective and Efficient Visible-Light Driven CO2 Reduction to CO in CH3CN/H2O Solution. Angew. Chem. 2017, 56, 738–743. [Google Scholar] [CrossRef] [PubMed]
  8. Schuchmann, K.; Müller, V. Direct and reversible hydrogenation of CO2 to formate by a bacterial carbon dioxide reductase. Science 2013, 342, 1382–1385. [Google Scholar] [CrossRef]
  9. Zhao, M.; Huang, Y.; Peng, Y.; Huang, Z.; Ma, Q.; Zhang, H. Two-dimensional metal–organic framework nanosheets: Synthesis and applications. Chem. Soc. Rev. 2018, 47, 6267–6295. [Google Scholar] [CrossRef]
  10. Wu, H.B.; Lou, X.W. Metal-organic frameworks and their derived materials for electrochemical energy storage and conversion: Promises and challenges. Sci. Adv. 2017, 3, eaap9252. [Google Scholar] [CrossRef] [PubMed]
  11. Wu, D.; Guo, Z.; Yin, X.; Pang, Q.; Tu, B.; Zhang, L.; Wang, Y.G.; Li, Q. Metal-organic frameworks as cathode materials for Li-O2 batteries. Adv. Mater. 2014, 26, 3258–3262. [Google Scholar] [CrossRef]
  12. Zhao, R.; Liang, Z.; Zou, R.; Xu, Q. Metal-organic frameworks for batteries. Joule 2018, 2, 2235–2259. [Google Scholar] [CrossRef] [Green Version]
  13. Yuan, S.; Feng, L.; Wang, K.; Pang, J.; Bosch, M.; Lollar, C.; Sun, Y.; Qin, J.; Yang, X.; Zhang, P.; et al. Stable metal–organic frameworks: Design, synthesis, and applications. Adv. Mater. 2018, 30, 1704303. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  14. Huang, L.; Zhang, X.; Han, Y.; Wang, Q.; Fang, Y.; Dong, S. In situ synthesis of ultrathin metal organic framework nanosheets: A new method for 2D metal-based nanoporous carbon electrocatalysts. J. Mater. Chem. A 2017, 5, 18610–18617. [Google Scholar] [CrossRef]
  15. Deng, X.; Li, R.; Wu, S.; Wang, L.; Hu, J.; Ma, J.; Jiang, W.; Zhang, N.; Zheng, X.; Gao, C.; et al. Metal–organic framework coating enhances the performance of Cu2O in photoelectrochemical CO2 reduction. J. Am. Chem. Soc. 2019, 141, 10924–10929. [Google Scholar] [CrossRef] [PubMed]
  16. Trickett, C.A.; Helal, A.; Al-Maythalony, B.A.; Yamani, Z.H.; Cordova, K.E.; Yaghi, O.M. The chemistry of metal–organic frameworks for CO2 capture, regeneration and conversion. Nat. Rev. Mater. 2017, 2, 17045. [Google Scholar] [CrossRef]
  17. Zhou, H.C.; Long, J.R.; Yaghi, O.M. Introduction to metal-organic frameworks. Chem. Rev. 2012, 112, 673. [Google Scholar] [CrossRef]
  18. Furukawa, H.; Cordova, K.E.; O’Keeffe, M.; Yaghi, O.M. The chemistry and applications of metal-organic frameworks. Science 2013, 341, 1230444. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  19. Nam, D.H.; Bushuyev, O.S.; Li, J.; De Luna, P.; Seifitokaldani, A.; Dinh, C.T.; Garciá de Arquer, F.P.; Wang, Y.; Liang, Z.; Proppe, A.H. Metal–organic frameworks mediate Cu coordination for selective CO2 electroreduction. J. Am. Chem. Soc. 2018, 140, 11378–11386. [Google Scholar] [CrossRef]
  20. Chen, E.X.; Qiu, M.; Zhang, Y.F.; Zhu, Y.S.; Liu, L.Y.; Sun, Y.Y.; Bu, X.H.; Zhang, J.; Lin, Q.P. Acid and base resistant zirconium polyphenolate-metalloporphyrin scaffolds for efficient CO2 photoreduction. Adv. Mater. 2018, 30, 1704388. [Google Scholar] [CrossRef]
  21. Xu, H.Q.; Hu, J.; Wang, D.; Li, Z.; Zhang, Q.; Luo, Y.; Yu, S.H.; Jiang, H.L. Visible-light photoreduction of CO2 in a metal–organic framework: Boosting electron–hole separation via electron trap states. J. Am. Chem. Soc. 2015, 137, 13440–13443. [Google Scholar] [CrossRef]
  22. Li, J.R.; Yu, J.; Lu, W.; Sun, L.-B.; Sculley, J.; Balbuena, P.B.; Zhou, H. Porous materials with pre-designed single-molecule traps for CO2 selective adsorption. Nat. Commun. 2013, 4, 1538. [Google Scholar] [CrossRef] [Green Version]
  23. Liu, J.; Chen, L.; Cui, H.; Zhang, J.; Zhang, L.; Su, C.Y. Applications of metal–organic frameworks in heterogeneous supramolecular catalysis. Chem. Soc. Rev. 2014, 43, 6011–6061. [Google Scholar] [CrossRef] [Green Version]
  24. Cui, Y.; Xu, H.; Yue, Y.; Guo, Z.; Yu, J.; Chen, Z.; Gao, J.; Yang, Y.; Qian, G.; Chen, B. A luminescent mixed-lanthanide metal–organic framework thermometer. J. Am. Chem. Soc. 2012, 134, 3979–3982. [Google Scholar] [CrossRef]
  25. Smit, B.; Maesen, T.L. Towards a molecular understanding of shape selectivity. Nature 2008, 451, 671–678. [Google Scholar] [CrossRef] [Green Version]
  26. Zhu, Q.; Yang, D.; Liu, H.; Sun, X.; Chen, C.; Bi, J.; Liu, J.; Wu, H.; Han, B. Hollow Metal–Organic-Framework-Mediated In Situ Architecture of Copper Dendrites for Enhanced CO2 Electroreduction. Angew. Chem. 2020, 132, 8981–8986. [Google Scholar] [CrossRef]
  27. Kang, X.; Li, L.; Sheveleva, A.; Han, X.; Li, J.; Liu, L.; Tuna, F.; McInnes, E.J.; Han, B.; Yang, S.; et al. Electro-reduction of carbon dioxide at low over-potential at a metal–organic framework decorated cathode. Nat. Commun. 2020, 11, 5464. [Google Scholar] [CrossRef]
  28. Dou, S.; Song, J.; Xi, S.; Du, Y.; Wang, J.; Huang, Z.F.; Xu, Z.J.; Wang, X. Boosting electrochemical CO2 reduction on metal–organic frameworks via ligand doping. Angew. Chem. 2019, 131, 4081–4085. [Google Scholar] [CrossRef]
  29. Yi, J.D.; Si, D.H.; Xie, R.; Yin, Q.; Zhang, M.D.; Wu, Q.; Chai, G.L.; Huang, Y.B.; Cao, R. Conductive Two-Dimensional Phthalocyanine-based Metal–Organic Framework Nanosheets for Efficient Electroreduction of CO2. Angew. Chem. 2021, 133, 17245–17251. [Google Scholar] [CrossRef]
  30. Majidi, L.; Ahmadiparidari, A.; Shan, N.; Misal, S.N.; Kumar, K.; Huang, Z.; Rastegar, S.; Hemmat, Z.; Zou, X.; Zapol, P.; et al. 2D Copper Tetrahydroxyquinone Conductive Metal–Organic Framework for Selective CO2 Electrocatalysis at Low Overpotentials. Adv. Mater. 2021, 33, 2004393. [Google Scholar] [CrossRef]
  31. Delley, B. From molecules to solids with the DMol 3 approach. J. Chem. Phys. 2000, 113, 7756–7764. [Google Scholar] [CrossRef]
  32. Perdew, J.P.; Ernzerhof, M.; Burke, K. Rationale for mixing exact exchange with density functional approximations. J. Chem. Phys. 1996, 105, 9982–9985. [Google Scholar] [CrossRef]
  33. Delley, B. Hardness conserving semilocal pseudopotentials. Phys. Rev. 2002, 66, 155125. [Google Scholar] [CrossRef]
  34. Grimme, S. Semiempirical GGA-type density functional constructed with a long-range dispersion correction. J. Comput. Chem. 2006, 27, 1787–1799. [Google Scholar] [CrossRef] [PubMed]
  35. Sun, Q.; Sun, C.; Du, A.; Dou, S.; Li, Z. In-plane graphene/boron-nitride heterostructures as an efficient metal-free electrocatalyst for the oxygen reduction reaction. Nanoscale 2016, 8, 14084–14091. [Google Scholar] [CrossRef]
  36. Qin, G.; Du, A.; Sun, Q. A theoretical insight into a feasible strategy for the fabrication of borophane. Phys. Chem. Chem. Phys. 2018, 20, 16216–16221. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  37. Qin, G.; Cui, Q.; Yun, B.; Sun, L.; Du, A.; Sun, Q. High capacity and reversible hydrogen storage on two dimensional C2N monolayer membrane. Int. J. Hydrogen Energy 2018, 43, 9895–9901. [Google Scholar] [CrossRef]
  38. Klamt, A.; Schüürmann, G. COSMO: A new approach to dielectric screening in solvents with explicit expressions for the screening energy and its gradient. J. Chem. Soc. Perkin Trans. 1993, 2, 799–805. [Google Scholar] [CrossRef]
  39. Monkhorst, H.J.; Pack, J.D. Special points for Brillouin-zone integrations. Phys. Rev. 1976, 13, 5188. [Google Scholar] [CrossRef]
  40. Back, S.; Yeom, M.; Jung, Y. Active Sites of Au and Ag Nanoparticle Catalysts for CO2 Electroreduction to CO. ACS Catal. 2015, 5, 5089–5096. [Google Scholar] [CrossRef]
  41. Rossmeisl, J.; Logadottir, A.; Nørskov, J.K. Electrolysis of water on (oxidized) metal surfaces. Chem. Phys. 2005, 319, 178–184. [Google Scholar] [CrossRef]
  42. Nørskov, J.K.; Rossmeisl, J.; Logadottir, A.; Lindqvist, L.; Kitchin, J.R.; Bligaard, T.; Jonsson, H. Origin of the overpotential for oxygen reduction at a fuel-cell cathode. J. Phys. Chem. 2004, 108, 17886–17892. [Google Scholar] [CrossRef]
  43. Liu, S.; Liu, Y.; Gao, X.; Tan, Y.; Cheng, Z.; Shen, Z.; Fan, M. Two-dimensional transition metal porphyrin sheets as a promising single-atom-catalyst for dinitrogen electrochemical reduction to ammonia: A theoretical study. J. Phys. Chem. 2019, 124, 1492–1499. [Google Scholar] [CrossRef]
  44. Shi, C.; Chan, K.; Yoo, J.S.; Nørskov, J.K. Barriers of electrochemical CO2 reduction on transition metals. Org. Process. Res. Dev. 2016, 20, 1424–1430. [Google Scholar] [CrossRef]
Nanomaterials 12 04049 g001 550
Figure 1. Structural diagram of TM-THQ single layer. (a) The top view of the single layer, (b) the side view of the single layer, and (c) the top view of the 2 × 2 super unit.
Figure 1. Structural diagram of TM-THQ single layer. (a) The top view of the single layer, (b) the side view of the single layer, and (c) the top view of the 2 × 2 super unit.
Nanomaterials 12 04049 g001
Nanomaterials 12 04049 g002 550
Figure 2. Bond length of the metal atom to the nearest O atom in the TM-THQ monolayer.
Figure 2. Bond length of the metal atom to the nearest O atom in the TM-THQ monolayer.
Nanomaterials 12 04049 g002
Nanomaterials 12 04049 g003 550
Figure 3. E c is the cohesion energy of the bulk metal, E b is the binding energy between the transition metal atoms and the tetrahydroxybenzoquinone monolayer.
Figure 3. E c is the cohesion energy of the bulk metal, E b is the binding energy between the transition metal atoms and the tetrahydroxybenzoquinone monolayer.
Nanomaterials 12 04049 g003
Nanomaterials 12 04049 g004 550
Figure 4. CO 2 RR versus HER at the first step of protonation Gibbs free energy on the TM-THQ monolayer surface. The catalyst is below the dashed line indicating good CO 2 RR selectivity.
Figure 4. CO 2 RR versus HER at the first step of protonation Gibbs free energy on the TM-THQ monolayer surface. The catalyst is below the dashed line indicating good CO 2 RR selectivity.
Nanomaterials 12 04049 g004
Nanomaterials 12 04049 g005 550
Figure 5. Flow chart of electrocatalytic CO 2 reduction to C 1 product scheme; red is the final product [43].
Figure 5. Flow chart of electrocatalytic CO 2 reduction to C 1 product scheme; red is the final product [43].
Nanomaterials 12 04049 g005
Nanomaterials 12 04049 g006 550
Figure 6. Gibbs free energy profile of CO 2 RR following the path of most favorable Zn-HAB at the zero potentiation. CO 2 molecules in the gaseous phase is given a free energy of zero on the clean catalytic surface.
Figure 6. Gibbs free energy profile of CO 2 RR following the path of most favorable Zn-HAB at the zero potentiation. CO 2 molecules in the gaseous phase is given a free energy of zero on the clean catalytic surface.
Nanomaterials 12 04049 g006
Nanomaterials 12 04049 g007 550
Figure 7. Gibbs free energy profile of CO 2 RR at zero potential along the most favorable route of Co-THQ. In the aseous stage, the free energy of a CO 2 molecule with a clean catalytic surface is zero.
Figure 7. Gibbs free energy profile of CO 2 RR at zero potential along the most favorable route of Co-THQ. In the aseous stage, the free energy of a CO 2 molecule with a clean catalytic surface is zero.
Nanomaterials 12 04049 g007
Nanomaterials 12 04049 g008 550
Figure 8. Gibbs free energy curves for (a) Ti-THQ, (b) V-THQ, (c) Cr-THQ, (d) Mn-THQ, (e) Fe-THQ, and (f) Zn-THQ, at zero potential, along the most favorable path of the CO 2 RR. The free energy zero point was set as the carbon dioxide molecule in the gaseous phase with a squeaky clean surface for the catalyst.
Figure 8. Gibbs free energy curves for (a) Ti-THQ, (b) V-THQ, (c) Cr-THQ, (d) Mn-THQ, (e) Fe-THQ, and (f) Zn-THQ, at zero potential, along the most favorable path of the CO 2 RR. The free energy zero point was set as the carbon dioxide molecule in the gaseous phase with a squeaky clean surface for the catalyst.
Nanomaterials 12 04049 g008
Nanomaterials 12 04049 g009 550
Figure 9. The Gibbs free-energy curve of CO 2 RR along the most favorable route of Cu-HQ at zero potential. The CO 2 molecules with clean catalytic surfaces in the gas phase are assigned a free energy of zero.
Figure 9. The Gibbs free-energy curve of CO 2 RR along the most favorable route of Cu-HQ at zero potential. The CO 2 molecules with clean catalytic surfaces in the gas phase are assigned a free energy of zero.
Nanomaterials 12 04049 g009
Nanomaterials 12 04049 g010a 550Nanomaterials 12 04049 g010b 550
Figure 10. Predicted partial density of states of *OCHOH adsorbed on Sc, Ti, V, and Cr (a–d). *CO adsorbs on Mn (e), *CHO adsorbs on Fe (f), and *COOH adsorbs on Co, Cu, and Zn (g–i). The dashed lines indicate Fermi levels. The red, blue and green wires represent the 3D orbitals of metallic atoms, the 2P orbitals of the oxygen atoms and the 2P orbitals of the carbon atoms, respectively.
Figure 10. Predicted partial density of states of *OCHOH adsorbed on Sc, Ti, V, and Cr (a–d). *CO adsorbs on Mn (e), *CHO adsorbs on Fe (f), and *COOH adsorbs on Co, Cu, and Zn (g–i). The dashed lines indicate Fermi levels. The red, blue and green wires represent the 3D orbitals of metallic atoms, the 2P orbitals of the oxygen atoms and the 2P orbitals of the carbon atoms, respectively.
Nanomaterials 12 04049 g010aNanomaterials 12 04049 g010b
Table
Table 1. Hirshfeld charges on the metal atom Q T M and oxygen atom Q O of the 10 TM-THQ system, the spin of the metal atom and the length of the TM-O.
Table 1. Hirshfeld charges on the metal atom Q T M and oxygen atom Q O of the 10 TM-THQ system, the spin of the metal atom and the length of the TM-O.
TM-THQQ TM /eSpin-TMQ O /eR TM − O /Å
Sc0.8790.000−0.2602.066
Ti0.7450.000−0.2301.968
V0.6070.000−0.2041.925
Cr0.659−2.977−0.2271.900
Mn0.4030.000−0.1731.881
Fe0.3290.000−0.1621.874
Co0.2830.000−0.1561.858
Ni0.2750.000−0.1581.885
Cu0.4800.000−0.2101.995
Zn0.5820.000−0.2262.029
Table
Table 2. Adsorption energies ( E a d s / e V ) with different reduced carbon dioxide products.
Table 2. Adsorption energies ( E a d s / e V ) with different reduced carbon dioxide products.
TM-THQCOHCOOHHCHOCH 3 OHCH 4
Sc−0.681−0.952−0.135−0.879−0.043
Ti−1.128−1.026−1.108−1.160−0.176
V−1.454−1.196−1.217−1.161−0.174
Cr−1.491−1.047−1.044−1.031−0.204
Mn−1.624−0.840−0.631−1.099−0.368
Fe−1.323−1.367−0.745−1.054−0.415
Co−0.557−0.406−0.351−0.499−0.138
Ni−0.314−0.311−0.266−0.242−0.096
Cu−0.539−0.637−0.448−0.611−0.313
Zn−0.918−0.8597−0.899−1.013−0.619
Table
Table 3. TM-HTQ is used as a rate-determining step for electrocatalytic CO 2 reduction, limiting potential ( U L /V), overpotential ( η /V).
Table 3. TM-HTQ is used as a rate-determining step for electrocatalytic CO 2 reduction, limiting potential ( U L /V), overpotential ( η /V).
TM-THQPDS U L η
Sc*OCHOH → * + HCOOH−0.8160.566
Ti*OCHOH + H+ + e−) → *CHO + H2O−1.0431.212
V*OCHOH + H+ + e−) → *CHO + H2O−0.6630.832
Cr*OCHOH + H+ + e−) → *CHO + H2O−0.2110.38
Mn*CO + H2O + H+ + e−) → *CHO + H2O−0.1450.314
Fe*CHO + H2O + H+ + e−) → *OCH2 + H2O−0.1470.316
Co* + CO2 + H+ + e−) → *COOH−0.2420.172
Cu* + CO2 + H+ + e−) → *COOH−0.8880.782
Zn* + CO2 + H+ + e−) → *COOH−0.7830.952
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Zeng, X.; Xiao, C.; Liao, L.; Tu, Z.; Lai, Z.; Xiong, K.; Wen, Y. Two-Dimensional (2D) TM-Tetrahydroxyquinone Metal–Organic Framework for Selective CO2 Electrocatalysis: A DFT Investigation. Nanomaterials 2022, 12, 4049. https://doi.org/10.3390/nano12224049

AMA Style

Zeng X, Xiao C, Liao L, Tu Z, Lai Z, Xiong K, Wen Y. Two-Dimensional (2D) TM-Tetrahydroxyquinone Metal–Organic Framework for Selective CO2 Electrocatalysis: A DFT Investigation. Nanomaterials. 2022; 12(22):4049. https://doi.org/10.3390/nano12224049

Chicago/Turabian Style

Zeng, Xianshi, Chuncai Xiao, Luliang Liao, Zongxing Tu, Zhangli Lai, Kai Xiong, and Yufeng Wen. 2022. "Two-Dimensional (2D) TM-Tetrahydroxyquinone Metal–Organic Framework for Selective CO2 Electrocatalysis: A DFT Investigation" Nanomaterials 12, no. 22: 4049. https://doi.org/10.3390/nano12224049

APA Style

Zeng, X., Xiao, C., Liao, L., Tu, Z., Lai, Z., Xiong, K., & Wen, Y. (2022). Two-Dimensional (2D) TM-Tetrahydroxyquinone Metal–Organic Framework for Selective CO2 Electrocatalysis: A DFT Investigation. Nanomaterials, 12(22), 4049. https://doi.org/10.3390/nano12224049

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop