Geotechnics, Volume 1, Issue 2 (December 2021) – 15 articles

Although there has been a substantial body of research on the chemical stabilization of sewage sludge, most of these results are project-specific and relate mainly to the use of new binders and sewage sludge from specific sources. In this sense, much of the work to date is context-specific. At present, there is still no general framework for estimating the strength of the chemically treated sludge. This paper proposes one such general framework, based on data from some recent studies. An in-depth re-interpretation of the data is first conducted, leading to the observation that sludge, which has coarse, hard particulate inclusions, such as sand, premixed into it, gives significantly higher strength. This was attributed to the hard coarse particles that lower the void ratio of treated soil, are much less susceptible to volume collapse under pressure, and contribute to the strength through frictional contacts and interlocking. This motivates the postulation of a general framework, based on the premise that coarse, hard particulate inclusions in the sludge which do not react with the binders can nonetheless contribute to the strength of the treated soil. The overall void ratio, defined as the volume of voids in the cementitious matrix normalised by the overall volume, is proposed as a parameter for quantifying the combined effect of the coarse particulate inclusions and the cementitious matrix. The binder-sludge ratio is another parameter which quantifies the strength of the cementitious matrix, excluding the hard particulate inclusions. Back-analysis of the data suggests that the significance of the binder-sludge ratio may diminish as the content of hard particulate inclusions increases. Full article

Expansive soils generally recognized as swell-shrink soils have been a problem for civil infrastructure for a long time. Engineers are in search of sustainable stabilization alternatives to counter these problematic soils. Microbial-induced calcium carbonate precipitation (MICP) is a promising biocementation process that can improve the properties of expansive soil through calcium carbonate precipitation. Past research has shown promise for the use of MICP in mitigating swelling distress from expansive soils. In this research, MICP via biostimulation was attempted by mixing enrichment and cementation solutions with soils in an effort to develop a new alternative to shallow chemical stabilization. Three soils with varying clay contents (30%, 40%, and 70%) and plasticity characteristics were selected, and soils were treated by mixing with enrichment solutions followed by cementation solutions. Five different mellowing periods, three different curing periods, and two types of cementation solutions were studied to optimize the method. Treatment effectiveness was evaluated using unconfined compression tests, calcium carbonate tests, and free swell index tests. Results showed that an increase in the mellowing period beyond two days was not beneficial for any of the three soils tested in this research. It was determined that the best improvement was observed at two days of mellowing and seven days of curing. Full article

The objective of this study is to develop data-driven predictive models for seismic energy dissipation of rocking shallow foundations during earthquake loading using multiple machine learning (ML) algorithms and experimental data from a rocking foundations database. Three nonlinear, nonparametric ML algorithms are considered: k-nearest neighbors regression (KNN), support vector regression (SVR) and decision tree regression (DTR). The input features to ML algorithms include critical contact area ratio, slenderness ratio and rocking coefficient of rocking system, and peak ground acceleration and Arias intensity of earthquake motion. A randomly split pair of training and testing datasets is used for initial evaluation of the models and hyperparameter tuning. Repeated k-fold cross validation technique is used to further evaluate the performance of ML models in terms of bias and variance using mean absolute percentage error. It is found that all three ML models perform better than multivariate linear regression model, and that both KNN and SVR models consistently outperform DTR model. On average, the accuracy of KNN model is about 16% higher than that of SVR model, while the variance of SVR model is about 27% smaller than that of KNN model, making them both excellent candidates for modeling the problem considered. Full article

This paper provides an in-depth review of research developments on a common phenomenon in oil and gas exploration: sand production. Due to its significant impact to reservoir productivity and production efficiency, sand production has been widely researched in recent years. This paper focused on the review of historical progress in experimental and analytical studies which helped to understand the nature of the sanding mechanism and identify conditions that favour the process. Collation of the experimental data and analytical solutions and formulations enabled the authors to comment on effectiveness and also limitations of the existing experimental protocols and analytical models. Sand production models were then grouped into categories based on initiation of sanding, rate and amount of sanding as well as the failure criterion incorporated in their formulation so that it will be more convenient for future researchers to identify and adopt an appropriate model for their own research. The review also confirms that there are still some aspects of sand production requiring further investigation, and maybe a hybrid approach combining experimental, analytical and numerical methods could be the best solution for future explorations. Full article

Colloidal silica (CS) is a kind of nanomaterial used in soil/rock grouting techniques in different branches of civil engineering. Many studies have recently been performed to investigate the potential of CS in improving the mechanical behavior of cohesionless soils and mitigating the risk of seismic liquefaction in urbanized areas. CS grout is chemically and biologically inert and, when injected into a subsoil, it can form a silica gel and stabilize the desired soil layer, thus representing an attractive, environmentally friendly alternative to standard chemical grouting techniques. This paper firstly describes the characteristics of CS grout, the gelation process and the main features of the behavior of the pure gelled material. The grout delivery mechanisms through porous media are then explained, pointing out the crucial issues for practical application of CS grouting. All the grouting-induced effects on the soil behavior, which have been investigated by laboratory tests on small-sized soil elements, are reviewed, including the modifications to soil strength and stiffness under both static and seismic loading conditions, to soil compressibility and hydraulic conductivity. Published results from physical model tests and in situ applications are also presented. Finally, some aspects related to the mechanism of soil improvement are discussed. A critical discussion of each topic is presented, drawing particular attention to the controversial or not yet fully examined aspects to which future research on colloidal silica grouting should be directed. Full article

The need to transit to greener options in soil stabilisation has revamped research on the use of industrial and agricultural by-products in order to cut down on the current carbon footprint from the use of ordinary Portland cement (OPC) and lime related binders for the treatment of problematic soils. This study is a review on the use of geopolymers constituted by alkali activation of several industrial wastes such as pulverised fuel ash (PFA), ground granulated blast furnace slag (GGBS), metakaolin (MK), glass powder (GP), palm oil fuel ash (POFA), silica fume (SF), rice husk ash (RHA), volcanic ash (VA), and marble powder (MP) for the stabilisation of weak clays. The performance of stabilised clays as subgrade and subbase materials for road pavement construction was evaluated by comparing the 7 day UCS of the treated clays with the strength requirement for stabilised materials as outlined in BS EN 16907-4. The result of the study shows that geopolymers can be employed in improving the engineering properties of problematic clays to meet practical applications. Strength improvement was observed in the stabilised clays with increased precursor content, molarity of alkaline activator, and curing period. Full article

The construction industry’s current dependence on primary aggregates is unsustainable as these are non-renewable resources and the consumption of these materials has a high environmental impact. The global annual production of primary aggregates is estimated to be 50 billion tonnes. In Europe, where 2 billion tonnes of primary aggregates are produced annually, approximately 90% of aggregates are utilised by the construction industry, whilst over 1 Gt of waste are sent to landfill; in the UK, 44% of landfilled waste arises from the construction industry. The drive to adopt a circular economy necessitates changes in resource use (including non-renewable aggregates). Recycling wastes, such as aggregates, could help this situation; whilst this concept is not new, it does not appear to have been widely embraced in geotechnical engineering. The aim of this paper is to highlight the benefits of increasing the use of alternative aggregates as this would enable the reserves of primary aggregates to be better maintained and less material would be landfilled—a win-win situation and a contributing step towards developing a truly circular economy. Full article

Gypseous soils are capable of presenting ground construction challenges to civil and geotechnical engineers due to their unpredictable deformation characteristics. These undesirable responses are sometimes caused by environmental changes in moisture content due to temperature variations, fluctuation of underground water table, surface water, and gypsum content. Hence, the adoption of effective and economical means of stabilising gypseous soils is imperative. This study’s focus is on the early age strength and microstructural characteristics of gypseous soils treated with lime and GGBS. Treated and untreated gypseous soils with 5%, 15%, and 25% gypsum content were subjected to wet–dry cycles while investigating unconfined compressive strength (UCS), water absorption, pH, microstructural changes, and swell. The analysis of the results shows that at zero cycle, the UCS of the untreated gypseous soils increases from 0.62 to 0.79 MPa and swell decreases from 69 to 23%, respectively, as gypsum content increases. However, upon subjection to wet–dry cycles, the UCS reduced from 0.16 to 0.08 MPa at the end of the sixth cycle due to dissolution of gypsum within the soil pores which reduced the strength. The result also shows that gypsum content increases water absorption and reduces the pH of the untreated gypseous soils because of the neutral pH of gypsum. Furthermore, lime-GGBS-treated gypseous soils maintained a higher pH after six wet–dry cycles compared to untreated gypseous soils due to the high pH of lime and the increase in calcium content which improved bonding. In addition, microstructural analysis using SEM indicated early age precipitation of cementitious compounds (CSH) for increasing strength of lime-GGBS-treated gypseous soils compared to untreated gypseous soils. Full article

Temperature differences between the surrounding ground and the tunnel lining will cause a variation of the tunnel lining forces. The hyperstatic reaction method (HRM) could be efficiently and simply used to investigate the impact of thermal load on tunnel linings. First, the steady state numerical solution is derived for a shallow circular tunnel to estimate the internal forces and displacements of tunnel lining caused by thermal load. The effective strain coefficient β_Tl is deduced to calculate the thermal stresses in tunnel lining. Secondly, the influence of the temperature difference on the internal forces of tunnel lining is investigated using the HRM method considering different lining elastic modulus, lining thickness and ground coefficient of thermal expansion. Lastly, the impact of fires which will be able to modify the elastic modulus of tunnel lining is investigated, which makes it possible to predict the damage of tunnel lining caused by fires. Full article

In this work, a quantitative uncertainty estimation of the random distribution of the soil material properties to the probability density functions of the failure load and failure displacements of a shallow foundation loaded with an oblique load is portrayed. A modified Cam Clay yield constitutive model is adopted with a stochastic finite element model. The random distribution of the reload path inclination $\kappa$, the critical state line inclination c of the soil and the permeability k of the Darcian water flow relation, has been assessed with Monte Carlo simulations accelerated by using Latin hypercube sampling. It is proven that both failure load and failure displacements follow Gaussian normal distribution despite the excessive non-linear behaviour of the soil. In addition, as the obliquity increases the mean value of failure load and the failure displacement always increases. The uncertainty of the output failure stress with the increase of the obliquity of the load remains the same. The failure spline of clays can be calculated within an acceptable accuracy with the proposed numerical scheme in every possible geometry and load conditions, considering the obliquity of the load in conjunction with non-linear constitutive relations. Full article

This paper illustrates two novel methods for computing the small-strain hysteretic material damping ratio, λ_min, of soils from the cyclic torsional shear (TS) and computing the small-strain viscous material damping ratio, D_min, from the free-vibration decay (FVD) testing. Both λ_min and D_min are challenging to measure, due to the significant level of ambient noise at small strains (<10⁻⁴%). A two-step method is proposed combining the Fourier Transform and a phase-based data fitting method for torsional shear testing, and this method can effectively eliminate the ambient noise at small strains. A Hilbert Transform-based method is proposed for the free-vibration decay testing in order to achieve a more accurate measurement of the viscous material damping ratio, D, at different strain levels, especially at small strains. The improved λ_min and D_min at small strains are compared to data available in the literature. The two novel methods are shown to be accurate in computing the small-strain damping ratios. Full article

Subgrade materials refer to the original ground underneath a road pavement, when these materials are made up of expansive soil it is referred to as expansive subgrade. Sometimes, these materials do not have sufficient capacity to support the weight of the road pavement and traffic load, which means they require some form of modification and re-engineering to enhance their load capacity. Chemical modification techniques using traditional stabilisers (such as cement and lime) have proved to be an effective means of subgrade stabilisation. However, high costs and environmental concerns associated with the use and production of these additives have highlighted the need for more sustainable and environmentally friendly substitutes. This study reviews the use of industrial by-products and other waste materials used for subgrade stabilisation, focusing on the sustainability of using processed wastes and how they alter the engineering properties of weak subgrade, compared to the use of cement and also reviews the availability of processed waste materials in quantities sufficient to meet the current demand for subgrade stabilisation. The findings illustrate that, processed waste is less expensive and has better sustainability credentials compared to cement. Moreover, processed wastes are available in sufficient quantities to meet existing demands for subgrade stabilisation. Therefore, it is recommended that the use of processed wastes should be promoted and utilised to improve and enhance the geotechnical properties of weak subgrade materials where possible. Full article

Natural soils are usually heterogeneous and characterized with complex microstructures. Sand–clay mixtures are often used as simplified soils to investigate the mechanical properties of soils with various compositions (from clayey to sandy soils) in the laboratory. Performing laboratory tests on a sand–clay mixture with definite clay fraction can provide information to understand the simplified soils’ mechanical behavior and better predict natural soils’ behavior at the engineering scale. This paper reviews previous investigations on sand–clay mixture and soil–structure interface direct shear test. It finds that even though there are many investigations on sand–clay mixtures and soil–structure interfaces that consider pure sand or pure clay, limited data on the mechanical behavior of the interface between sand–clay mixture and structure materials are available. Knowledge is missing on how the clay content influences the mechanical behavior of interface and how the soil particles’ arrangement changes as the clay content increases. Further study should be performed to investigate the interface in terms of a reconstituted sand–clay mixture and structure by interface direct shear test, to highlight the influence of clay fraction on the interface response, under various loading conditions. Full article

This paper presents a laboratory investigation into the mechanical response of a silty sand, with a fines content of 10%, stabilized with colloidal silica (CS). To this end, a series of unconfined compression tests as well as monotonic and cyclic triaxial tests was performed on a silty sand, comprising a mixture of a clean sand and a silty sand, stabilized with two concentrations of CS. The effect of various parameters on the behaviour of the stabilized silty sand was studied, such as CS concentration, soil density, and the presence of fines. The test results were compared with the corresponding of the untreated silty sand as well as the parent clean sand. It is shown that stabilization, even at the lowest CS = 6% concentration studied, significantly improves the undrained shear strength as well as the liquefaction resistance of the stabilized silty sand. Both the monotonic and cyclic response of the stabilized soil are only slightly affected by density. Furthermore, cyclic straining up to at least 5% of double-amplitude axial strain does not influence the undrained shear strength of the stabilized silty sand. Full article

This paper presents the results of a laboratory investigation into the effect of non-plastic fines on the correlation between liquefaction resistance and the shear wave velocity of sand. For this purpose, undrained stress-controlled cyclic triaxial and bender element tests were performed on clean sand and its mixtures with non-plastic silt. It is shown that the correlation between liquefaction resistance and shear wave velocity depends on fines content and confining effective stress. Based on the test results, correlation curves between field liquefaction resistance and overburden stress corrected shear wave velocity for sand containing various contents of fines are derived. These curves are compared to other previously proposed by field and laboratory studies. Full article