Advanced Metal Welding and Joining Technologies

A special issue of Metals (ISSN 2075-4701). This special issue belongs to the section "Welding and Joining".

Deadline for manuscript submissions: closed (31 December 2023) | Viewed by 11291

Special Issue Editor

Institute of Light Alloy and Processing, Faculty of Materials and Manufacturing, Beijing University of Technology, Beijing 100124, China
Interests: welding metallurgy; light metals; resistance spot welding
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

Welding and joining is the key assembling process in modern industry. The application of next-generation structural materials demands novel welding and joining technologies to yield high-quality products. Across this trend, the fundamental research involved not only the evolution of material properties during processing, but also the development of suitable equipment and necessary methods. This Special Issue is focused on advanced metal welding and joining technologies, of which the concerned topics include: (1) advanced metals that trigger demands for specific processing techniques; (2) fundamental research on the issue of material evolution during processing; (3) the service performance of the advanced metal joints; and (4) novel welding and joining devices and methods. Furthermore, any research which is related to metal processing technology will also be considered.

Dr. Yu Zhang
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Metals is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • welding metallurgy
  • light metals
  • high-entropy alloy
  • bulk metallic glass
  • mechanical property
  • corrosion
  • hybrid joining technique
  • dissimilar metal joining

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Related Special Issue

Published Papers (6 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Jump to: Review

13 pages, 33709 KiB  
Article
In Situ Observations of the Strain Competition Phenomenon in Aluminum Alloy Resistance Spot Welding Joints during Lap Shear Testing
by Yu Zhang, Jiaxi Tang, Tong Liu, Xiaoyu Ma and Yipeng Wang
Metals 2023, 13(9), 1601; https://doi.org/10.3390/met13091601 - 15 Sep 2023
Cited by 3 | Viewed by 1123
Abstract
The real-time evolution of the deformation and strain field of non-heat-treatable aluminum alloy 5754 and heat-treatable aluminum alloy 6061 resistance spot welding joints during the lap shear test was extracted using the digital image correlation (DIC) technique. The strain competition phenomenon between the [...] Read more.
The real-time evolution of the deformation and strain field of non-heat-treatable aluminum alloy 5754 and heat-treatable aluminum alloy 6061 resistance spot welding joints during the lap shear test was extracted using the digital image correlation (DIC) technique. The strain competition phenomenon between the nugget and its peripheral metal was quantitatively analyzed by applying 2D and 3D DIC analyses. The quantitative data show the tensile strain concentrated in the peripheral metal of the AA5754-O joint, which fractured in the pull-out mode. In comparison, a significant shear strain appears in the nugget of the AA6061-T6 joint, leading to its fracture in the interfacial failure mode during the lap shear test. The phase evolution of the nugget was analyzed using the thermodynamics database JMatPro, which was further used to calculate the local strength of the joints. The results indicate that the nugget strength of AA5754 is 223 MPa, the nugget strength of AA6061 is 178 MPa, and the heat-affected zone (HAZ) strength of AA6061 is 263 MPa. By inputting the local strength data, the calculated result of the analytical load-bearing competition model is in accordance with the experimental data of the lap shear test. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Figure 1

20 pages, 19640 KiB  
Article
Features of Intermetallic Formation in the Solid Phase on a Steel–Titanium Bimetal Interface under the Conditions of Arc Welding
by Volodymyr Korzhyk, Yupeng Zhang, Vladyslav Khaskin, Oleg Ganushchak, Valeryi Kostin, Viktor Kvasnytskyi, Andrii Perepichay and Andrii Grynyuk
Metals 2023, 13(8), 1338; https://doi.org/10.3390/met13081338 - 26 Jul 2023
Viewed by 1129
Abstract
The object of this study is the formation of intermetallic phases (IMPhs) in the heat-affected zone (HAZ) of joints of steel–titanium bimetal plates produced by arc welding. A titanium layer (2 mm) was welded by the plasma method (PAW), a barrier layer of [...] Read more.
The object of this study is the formation of intermetallic phases (IMPhs) in the heat-affected zone (HAZ) of joints of steel–titanium bimetal plates produced by arc welding. A titanium layer (2 mm) was welded by the plasma method (PAW), a barrier layer of Cusi3Mn1 bronze was deposited on it by the TIG method, the first steel layer was deposited by CMT, and Puls-MAG was used for filling the groove. Here, heating in the solid phase takes place in the HAZ, which may lead to undesirable formation of brittle IMPhs and further welded joint failure. Mathematical modeling was performed and metallurgical features formed during the processes of heating of the HAZ in bimetal steel–titanium plates were studied to identify the risk of IMPh formation. It was found that at a temperature increase from 900 to 1450 °C, a continuous intermetallic layer formed on the steel–titanium interface, which contained FeTi IMPh, and the width of which increased from 1 to 10 μm. In the temperature range 1300…1430 °C, an intermetallic TiFe2-type phase additionally formed from the titanium side. In the temperature range 1430…1450 °C, the TiFe2 phase was replaced by the TiXFe phase, which formed both from the steel side and from the titanium side. This phase consists of intermetallics (73–75% Ti + 27–25% Fe) and (80–85% Ti + 20–15% Fe), and it is close to the Ti2Fe-type phase. The interlayer of intermetallics, formed at temperatures of 900…1300 °C, has a continuous morphology (HV0.01–650…690). At temperatures rising above 1300 °C, the IMPh interlayer became more ramified (HV0.01–590…610) because of the formation of a larger number of pores and microcracks within it. In the temperature range 900…1450 °C, solid-phase diffusion proceeded in the steel–titanium bimetal near the interface of the two metals. A zone of iron diffusion, 5–10 μm to 40–60 μm in width, formed in titanium. In steel, a zone of titanium diffusion 15–20 μm to 120–150 μm in width formed, starting from 1300 °C and higher. It is recommended to perform industrial welding of steel–titanium bimetal in modes, for which the heat input is equal to 200…400 J/mm. Here, during the period 10–12 s, the heating temperature of the HAZ 1.5–3.5 mm in width is equal to 900–1150 °C. It promotes formation of an intermetallic FeTi-type interlayer of up to 1–2 μm width. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Figure 1

13 pages, 6106 KiB  
Article
Experimental and Simulation Studies of Micro-Swing Arc Welding Process for X80M Pipeline
by Zhili Luo, Yan Li, Hong Zhang and Pengyu Wang
Metals 2023, 13(7), 1228; https://doi.org/10.3390/met13071228 - 3 Jul 2023
Cited by 2 | Viewed by 1445
Abstract
Pipe girth welds are prone to incomplete fusion problems in the automatic welding process of long-distance pipelines, which is often related to temperature inhomogeneity in the weld bead. The narrow gap and micro-swing welding technique was applied in pipeline construction to improve welding [...] Read more.
Pipe girth welds are prone to incomplete fusion problems in the automatic welding process of long-distance pipelines, which is often related to temperature inhomogeneity in the weld bead. The narrow gap and micro-swing welding technique was applied in pipeline construction to improve welding quality. The manuscript provides a detailed investigation of the micro-swing welding technique with a combination of welding experiments and numerical simulation. A swing welding strategy was proposed according to the actual welding condition in pipeline construction to study the formation mechanism of weld joints. The swing width grew to 1.25–1.35 times from the 3 to 6 o’clock position in the same filling layer. It also increased with filling layers, and filling layer 5 had the biggest swing width, almost two times that of filling layer 2. “Middle concave” morphology appeared at the 3 o’clock position, which could effectively avoid the occurrence of incomplete fusion, while “hump” morphology may appear at the 6 o’clock position, and incomplete fusion defects occurred if the next pass failed to eliminate the influence of the “hump”. The temperature field presented an obvious “sawtooth” shape at small swing frequencies, which could cause temperature inhomogeneity. It could be effectively eliminated when swing frequency reached over 5 Hz. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Graphical abstract

15 pages, 6066 KiB  
Article
Effect of Brazing Temperature on Microstructure, Tensile Strength, and Oxide Film-Breaking Synergy of 5A06 Aluminum Alloy Welded by TG-TLP
by Yi Chen, Qiang Liu, Peiyun Xia, Tiesong Lin, Chengcong Zhang, Nengtao Zhou and Yongde Huang
Metals 2023, 13(6), 1048; https://doi.org/10.3390/met13061048 - 30 May 2023
Cited by 1 | Viewed by 1564
Abstract
5A06 aluminum alloy bar was brazed by temperature gradient transient liquid phase diffusion welding (TG-TLP). The effects of brazing temperature on the microstructure and the tensile strength of the brazing joints were investigated. Three typical brazing filler alloys (1# Al-20Cu-6Si-2Ni, 2# [...] Read more.
5A06 aluminum alloy bar was brazed by temperature gradient transient liquid phase diffusion welding (TG-TLP). The effects of brazing temperature on the microstructure and the tensile strength of the brazing joints were investigated. Three typical brazing filler alloys (1# Al-20Cu-6Si-2Ni, 2# Al-10Cu-10Si-3Mg-1Ga, and 3# Al-6Cu-10Si-2Mg-10Zn) were prepared by smelting, and TG-TLP diffusion bonding was carried out at different brazing temperatures (550 °C~590 °C). The results show that with the increase in brazing temperature, the oxide films at the brazing junction are easier to be broken and dispersed, but the oxidation extent will also increase. The oxidation products enriched were mainly Al2O3 and SiO2 at the brazing junction. There are different optimal brazing temperatures corresponding to the different filler alloys. For 1#, the optimal temperature is 570 °C; for 2# is 580 °C; for 3# is 580 °C. For 1# brazing joints, the maximum tensile strength was 113 MPa, and for 2# was 122.4 MPa. Under the experimental conditions of this study, the maximum tensile strength of the TG-TLP joint is 147.4 MPa of 3# brazing sample (at 580 °C), which has increased by 30% and 20% compared to 1# and 2# respectively. The nickel-rich phase at the interface (of 1# brazing filler) could form a brittle fracture, which was unfavorable for interface bonding. For TG-TLP brazing of 5A06, the filler alloy with high Al:Cu ratio (12:1 wt.%) needs a sufficient temperature gradient to exert the film-breaking effect, while the filler alloy with low Al:Cu ratio (3.6:1 wt.%) needs to accurately control its brazing temperature to avoid excessive oxidation. There are many research gaps in the influence of brazing material composition and brazing temperature on the microstructure and mechanical properties of 5A06 aluminum alloy TG-TLP joints. The research results can provide a theoretical basis for formulating the TG-TLP brazing specification of 5A06 aluminum alloy. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Figure 1

Review

Jump to: Research

18 pages, 5310 KiB  
Review
Quality Assurance in Resistance Spot Welding: State of Practice, State of the Art, and Prospects
by Panagiotis Stavropoulos and Kyriakos Sabatakakis
Metals 2024, 14(2), 185; https://doi.org/10.3390/met14020185 - 2 Feb 2024
Cited by 7 | Viewed by 2470
Abstract
Resistance spot welding is a process with high variability regarding the quality of the produced joints. This means that key performance indicators (KPIs) such as geometrical and mechanical features as well as failure modes can deviate from the initial design even if the [...] Read more.
Resistance spot welding is a process with high variability regarding the quality of the produced joints. This means that key performance indicators (KPIs) such as geometrical and mechanical features as well as failure modes can deviate from the initial design even if the same process parameters are used. The industry has developed quality assurance programs and quality control methods for tracking these KPIs; however, most of them are based on offline or/and destructive practices. On the other hand, state-of-the-art approaches have made online quality assessment feasible and proved its necessity if a 100% quality rate is required. However, limited attention has been given to “closing the loop” and providing feedback for preventing and correcting process anomalies that cause quality variations in real time. In this study, the main gaps between the state of practice and the state of the art are discussed in the context of quality assurance for resistance spot welding. Finally, the role and importance of digital twins by taking into consideration the entire welding ecosystem in quality assurance are discussed in order to form the prospects for the road ahead. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Figure 1

23 pages, 5008 KiB  
Review
Solid-State Welding of Aluminum to Magnesium Alloys: A Review
by Hao Chen, Zhengqiang Zhu, Yunming Zhu, Liang Sun and Yukun Guo
Metals 2023, 13(8), 1410; https://doi.org/10.3390/met13081410 - 7 Aug 2023
Cited by 6 | Viewed by 3015
Abstract
With the continuous improvement of lightweight requirements, the preparation of Mg/Al composite structures by welding is in urgent demand and has broad prospective applications in the industrial field. However, it is easy to form a large number of brittle intermetallic compounds when welding [...] Read more.
With the continuous improvement of lightweight requirements, the preparation of Mg/Al composite structures by welding is in urgent demand and has broad prospective applications in the industrial field. However, it is easy to form a large number of brittle intermetallic compounds when welding Mg/Al dissimilar alloys, and it is difficult to obtain high-quality welded joints. The solid-state welding method has the characteristics of low energy input and high efficiency, which can inhibit the formation of brittle intermetallic compounds and help to solve the problem of the poor strength of welded joints using Mg/Al dissimilar alloys in engineering applications. Based on the literature of ultrasonic welding, friction welding, diffusion welding, explosive welding, magnetic pulse welding, and resistance spot welding of Al/Mg in recent years, this paper summarized and prospected the research status of solid-state welding using Mg/Al dissimilar alloys from three aspects: the optimization of welding parameters, the addition of interlayers, and hybrid welding process. Full article
(This article belongs to the Special Issue Advanced Metal Welding and Joining Technologies)
Show Figures

Figure 1

Back to TopTop