Polymers

Research

18 pages, 3302 KiB

Open AccessArticle

Secondary Raw Materials from Residual Carbon Fiber-Reinforced Composites by An Upgraded Pyrolysis Process

by Alexander Lopez-Urionabarrenechea, Naia Gastelu, Alberto Jiménez-Suárez, Silvia G. Prolongo, Adriana Serras-Malillos, Esther Acha and Blanca María Caballero

Polymers 2021, 13(19), 3408; https://doi.org/10.3390/polym13193408 - 4 Oct 2021

Cited by 12 | Viewed by 2581

Abstract

This paper presents a process where carbon fibers and hydrogen can be recovered simultaneously through a two-stage thermal treatment of an epoxy-carbon fiber composite. For this purpose, some pieces of epoxy resin reinforced with carbon fiber fabrics have been fabricated and, after curing, [...] Read more.

This paper presents a process where carbon fibers and hydrogen can be recovered simultaneously through a two-stage thermal treatment of an epoxy-carbon fiber composite. For this purpose, some pieces of epoxy resin reinforced with carbon fiber fabrics have been fabricated and, after curing, have been pyrolyzed in an installation consisting of two reactors. In the first one, the thermal decomposition of the resin takes place, and in the second one, the gases and vapors coming from the first reactor are thermally treated. Once this process is completed, the solid generated is oxidized with air to eliminate the resin residues and carbonaceous products from the fibers surface. The recovered carbon fiber fabrics have been reused to make new cured parts and their electrical and mechanical properties have been measured. The results show that it is possible to obtain carbon fiber fabrics that can be processed as they leave the recycling process and that retain 80% of the tensile modulus, 70% of the flexural strength, and 50% of the interlaminar shear strength. At the same time, a gaseous stream with more than 66% by volume of hydrogen can be obtained, reaching a maximum of 81.7%. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Graphical abstract

14 pages, 2286 KiB

Open AccessArticle

A “Wastes-Treat-Wastes” Technology: Role and Potential of Spent Fluid Catalytic Cracking Catalysts Assisted Pyrolysis of Discarded Car Tires

by Baishun Zhao, Chuansheng Wang and Huiguang Bian

Polymers 2021, 13(16), 2732; https://doi.org/10.3390/polym13162732 - 15 Aug 2021

Cited by 7 | Viewed by 2868

Abstract

Spent fluid catalytic cracking catalysts (FCC catalysts) produced by the petrochemical industry are considered to be environmentally hazardous waste, and precious metals and heavy metals deposited on the surface make them difficult to treat. Even so, these catalysts retain some of their activity. [...] Read more.

Spent fluid catalytic cracking catalysts (FCC catalysts) produced by the petrochemical industry are considered to be environmentally hazardous waste, and precious metals and heavy metals deposited on the surface make them difficult to treat. Even so, these catalysts retain some of their activity. The pyrolysis of waste tires is considered to be one of the most effective ways to solve the fossil fuel resource crisis, and this study attempts to catalyze the pyrolysis of waste tires using spent catalysts to increase the value of both types of waste. FCC catalysts reduced the activation energy (E) of waste tire pyrolysis. When the catalyst dosage was 30 wt.%, the E of tread rubber decreased from 238.87 kJ/mol to 181.24 kJ/mol, which was a 19.94% reduction. The E of the inner liner decreased from 288.03 kJ/mol to 209.12 kJ/mol, a 27.4% reduction. The spent catalyst was more effective in reducing the E and solid yield of the inner liner made of synthetic rubber. It should be emphasized that an appropriate increase in the heating rate can fully exert the selectivity of the catalyst. The catalyst could also be effectively used twice, and the optimum ratio of catalyst/waste tires was about 1/4.5. Compared with specially prepared catalysts, it is more cost-effective to use such wastes as a catalyst for waste tire pyrolysis. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Graphical abstract

24 pages, 11472 KiB

Open AccessArticle

Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials

by Jerzy Korol, Aleksander Hejna, Klaudiusz Wypiór, Krzysztof Mijalski and Ewelina Chmielnicka

Polymers 2021, 13(9), 1383; https://doi.org/10.3390/polym13091383 - 23 Apr 2021

Cited by 17 | Viewed by 4142

Abstract

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated [...] Read more.

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were modified with 2.5 wt % of commercially available compatibilizers. The mechanical and thermal performance of modified wastes were evaluated by tensile tests, thermogravimetric analysis, and differential scanning calorimetry. It was found that incorporation of such a small amount of modifiers may overcome the drawbacks caused by the presence of impurities. The incorporation of maleic anhydride-grafted compounds enhanced the tensile strength of wastes by 13–25%. The use of more ductile compatibilizers—ethylene-vinyl acetate and paraffin increased the elongation at break by 55–64%. The presence of compatibilizers also reduced the stiffness of materials resulting from the presence of solid particles. It was particularly emphasized for styrene-ethylene-butadiene-styrene and ethylene-vinyl acetate copolymers, which caused up to a 20% drop of Young’s modulus. Such effects may facilitate the further applications of analyzed wastes, e.g., in polymer film production. Thermal performance was only slightly affected by compatibilization. It caused a slight reduction in polyethylene melting temperatures (up to 2.8 °C) and crystallinity degree (up to 16%). For more contaminated materials, the addition of compatibilizers caused a minor reduction in the decomposition onset (up to 6 °C). At the same time, for the waste after three washing cycles, thermal stability was improved. Moreover, depending on the desired properties and application, materials do not have to go through the whole recycling line, simplifying the process, reducing energy and water consumption. The presented results indicate that it is possible to efficiently use the materials, which do not have to undergo the whole recycling process. Despite the presence of impurities, they could be applied in the manufacturing of products which do not require exceptional mechanical performance. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Graphical abstract

11 pages, 8354 KiB

Open AccessArticle

Effects of a Twin-Screw Extruder Equipped with a Molten Resin Reservoir on the Mechanical Properties and Microstructure of Recycled Waste Plastic Polyethylene Pellet Moldings

by Hikaru Okubo, Haruka Kaneyasu, Tetsuya Kimura, Patchiya Phanthong and Shigeru Yao

Polymers 2021, 13(7), 1058; https://doi.org/10.3390/polym13071058 - 27 Mar 2021

Cited by 10 | Viewed by 5364

Abstract

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion [...] Read more.

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion can restore the mechanical properties; thus, we propose a twin-screw extruder with a molten resin reservoir (MSR), a cavity between the screw zone and twin-screw extruder discharge, which retains molten polymer after mixing in the twin-screw zone, thus influencing the polymer properties. Re-extruded recycled polyethylene (RPE) pellets were produced, and the tensile properties and microstructure of virgin polyethylene (PE), unextruded RPE, and re-extruded RPE moldings prepared with and without the MSR were evaluated. Crucially, the elongation at break of the MSR-extruded RPE molding was seven times higher than that of the original RPE molding, and the Young’s modulus of the MSR-extruded RPE molding was comparable to that of the virgin PE molding. Both the MSR-extruded RPE and virgin PE moldings contained similar striped lamellae. Thus, MSR re-extrusion improved the mechanical performance of recycled polymers by optimizing the microstructure. The use of MSRs will facilitate the reuse of waste plastics as value-added materials having a wide range of industrial applications. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Figure 1

17 pages, 3737 KiB

Open AccessEditor’s ChoiceArticle

A Win–Win Combination to Inhibit Persistent Organic Pollutant Formation via the Co-Incineration of Polyvinyl Chloride E-Waste and Sewage Sludge

by Gerard Gandon-Ros, Samuel S. Nuñez, Nuria Ortuño, Ignacio Aracil, María Francisca Gómez-Rico and Juan A. Conesa

Polymers 2021, 13(5), 835; https://doi.org/10.3390/polym13050835 - 9 Mar 2021

Cited by 9 | Viewed by 3246

Abstract

Persistent organic pollutant inhibition in the combustion process of polyvinyl chloride (PVC) by prior addition of an inhibitor is currently being studied, reducing the emission of pollutants, and thus reducing the large amount of waste PVC destined for landfill. In this work, the [...] Read more.

Persistent organic pollutant inhibition in the combustion process of polyvinyl chloride (PVC) by prior addition of an inhibitor is currently being studied, reducing the emission of pollutants, and thus reducing the large amount of waste PVC destined for landfill. In this work, the use of sewage sludge (SS) as an alternative to chemical inhibitors to improve the quality emissions of the incineration of polyvinyl chloride waste (PVC e-waste) was studied and optimized. Different combustion runs were carried out at 850 °C in a laboratory tubular reactor, varying both the molar ratio R_i (0.25, 0.50, 0.75) between inhibitors (N + S) and chlorine (Cl) and the oxygen ratio λ (0.15, 0.50) between actual oxygen and stoichiometric oxygen. The emissions of several semivolatile compounds families such as polycyclic aromatic hydrocarbons (PAHs), polychlorobenzenes (ClBzs), and polychlorophenols (ClPhs), with special interest in the emissions of the most toxic compounds, i.e., polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs), were analyzed. A notable decrease in PCDD/F and dl-PCB formation was achieved in most of the experiments, especially for those runs performed under an oxygen-rich atmosphere (λ = 0.50), where the addition of sludge was beneficial with inhibition ratios Ri ≥ 0.25. An inhibition ratio of 0.75 showed the best results with almost a 100% reduction in PCDD/F formation and a 95% reduction in dl-PCB formation. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Figure 1

17 pages, 3536 KiB

Open AccessArticle

Py–FTIR–GC/MS Analysis of Volatile Products of Automobile Shredder Residue Pyrolysis

by Bin Yang and Ming Chen

Polymers 2020, 12(11), 2734; https://doi.org/10.3390/polym12112734 - 18 Nov 2020

Cited by 13 | Viewed by 3387

Abstract

Automobile shredder residue (ASR) pyrolysis produces solid, liquid, and gaseous products, particularly pyrolysis oil and gas, which could be used as renewable alternative energy resources. Due to the primary pyrolysis reaction not being complete, the yield of gaseous product is low. The pyrolysis [...] Read more.

Automobile shredder residue (ASR) pyrolysis produces solid, liquid, and gaseous products, particularly pyrolysis oil and gas, which could be used as renewable alternative energy resources. Due to the primary pyrolysis reaction not being complete, the yield of gaseous product is low. The pyrolysis tar comprises chemically unstable volatiles before condensing into liquid. Understanding the characteristics of volatile products will aid the design and improvement of subsequent processes. In order to accurately analyze the chemical characteristics and yields of volatile products of ASR primary pyrolysis, TG–FTIR–GC/MS analysis technology was used. According to the analysis results of the Gram–Schmidt profiles, the 3D stack plots, and GC/MS chromatograms of MixASR, ASR, and its main components, the major pyrolytic products of ASR included alkanes, olefins, and alcohols, and both had dense and indistinguishable weak peaks in the wavenumber range of 1900–1400 cm⁻¹. Many of these products have unstable or weaker chemical bonds, such as =CH–, =CH2, –C=C–, and –C=CH2. Hence, more syngas with higher heating values can be obtained with further catalytic pyrolysis gasification, steam gasification, or higher temperature pyrolysis. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Figure 1

10 pages, 1547 KiB

Open AccessArticle

Pyrolysis for Nylon 6 Monomer Recovery from Teabag Waste

by Soosan Kim, Nahyeon Lee and Jechan Lee

Polymers 2020, 12(11), 2695; https://doi.org/10.3390/polym12112695 - 16 Nov 2020

Cited by 31 | Viewed by 4429

Abstract

In this work, we used pyrolysis to treat teabag waste (TBW). Changes in the pyrolysis temperature affected the composition and yield of the products. For example, more non-condensable gases and less char were produced with an increase in the pyrolysis temperature. Pyrolysis conducted [...] Read more.

In this work, we used pyrolysis to treat teabag waste (TBW). Changes in the pyrolysis temperature affected the composition and yield of the products. For example, more non-condensable gases and less char were produced with an increase in the pyrolysis temperature. Pyrolysis conducted under a nitrogen environment yielded caprolactam at temperatures between 400 and 700 °C. An increase in the pyrolysis temperature from 400 to 500 °C increased the caprolactam yield from 3.1 to 6.2 wt.%. At 700 °C, the yield decreased to 4.6 wt.%. The highest caprolactam yield (i.e., 6.2 wt.% at 500 °C) was equivalent to 59.2 wt.% on the basis of the weight of the non-biomass part of the TBW. The pyrolytic products other than caprolactam (e.g., combustible gases, pyrolytic liquid, and char) can function as fuels to supply energy during pyrolysis in order to increase and maintain the temperature. The higher heating values (HHVs) of the combustible gases and pyrolytic liquid produced at 500 °C were 7.7 and 8.3 MJ kg⁻¹, respectively. The HHV of the char produced at 500 °C was 23 MJ kg⁻¹, which is comparable to the HHV of coal. This work will help to develop effective pyrolysis processes to valorize everyday waste by recovering value-added chemicals such as polymer monomers and by producing alternative fuels. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Figure 1

10 pages, 9331 KiB

Open AccessArticle

Crystallization and Alkaline Degradation Behaviors of Poly(l-Lactide)/4-Armed Poly(ε-Caprolactone)-Block-Poly(d-Lactide) Blends with Different Poly(d-Lactide) Block Lengths

by Suyang Dai, Min Wang, Zhuoxin Zhuang and Zhenbo Ning

Polymers 2020, 12(10), 2195; https://doi.org/10.3390/polym12102195 - 25 Sep 2020

Cited by 7 | Viewed by 2353

Abstract

Four-armed poly(ε-caprolactone)-block-poly(d-lactide) (4-C-D) copolymers with different poly(d-lactide) (PDLA) block lengths (M_n,PDLAs) were synthesized by sequential ring-opening polymerization (ROP). The formation of stereocomplex (SC) crystallites in the 80/20 poly(l-lactide) (PLLA)/4-C-D blends were investigated [...] Read more.

Four-armed poly(ε-caprolactone)-block-poly(d-lactide) (4-C-D) copolymers with different poly(d-lactide) (PDLA) block lengths (M_n,PDLAs) were synthesized by sequential ring-opening polymerization (ROP). The formation of stereocomplex (SC) crystallites in the 80/20 poly(l-lactide) (PLLA)/4-C-D blends were investigated with the change of M_n,PDLA from 0.5 to 1.5 kg/mol. It was found that the crystallization and alkaline degradation of the blends were profoundly affected by the formed SC crystallites. The PLLA/4-C-D0.5 blend had the lowest crystallization rate of the three blends, and it was difficult to see spherulites in this blend by polarized optical microscopy (POM) observation after isothermal crystallization at 140 °C for 4 h. Meanwhile, when M_n,PDLA was 1 kg/mol or 1.5 kg/mol, SC crystallites could be formed in the PLLA/4-C-D blend and acted as nucleators for the crystallization of PLLA homo-crystals. However, the overall crystallization rates of the two blends were still lower than that of the neat PLLA. In the PLLA/4-C-D1.5 blend, the Raman results showed that small isolated SC spherulites were trapped inside the big PLLA homo-spherulites during isothermal crystallization. The degradation rate of the PLLA/4-C-D blend decreased when M_n,PDLA increased from 0.5 to 1.5 kg/mol, and the degradation morphologies had a close relationship with the crystallization state of the blends. This work revealed the gradual formation of SC crystallites with the increase in M_n,PDLA in the PLLA/4-C-D blends and its significant effect on the crystallization and degradation behaviors of the blend films. Full article

(This article belongs to the Special Issue Studies on Polymer Degradation and Recycling)

► Show Figures

Graphical abstract

Journal Menu

Journal Browser

Studies on Polymer Degradation and Recycling

Share This Special Issue

Special Issue Editor

Special Issue Information

Keywords

Benefits of Publishing in a Special Issue

Published Papers (8 papers)

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI