Sustainability

Editorial

Jump to: Research

2 pages, 161 KiB

Open AccessEditorial

Sustainable Building Materials and Life Cycle Assessment

by Adriana Estokova and Dagmar Samesova

Sustainability 2021, 13(4), 2012; https://doi.org/10.3390/su13042012 - 13 Feb 2021

Cited by 3 | Viewed by 2516

Abstract

Today, sustainability principles should be applied to all industries, including the building sector, which ranks among the sectors with the most negative environmental impacts [...] Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

Research

Jump to: Editorial

21 pages, 3252 KiB

Open AccessArticle

Life Cycle Assessment Framework for Embodied Environmental Impacts of Building Construction Systems

by Mona Abouhamad and Metwally Abu-Hamd

Sustainability 2021, 13(2), 461; https://doi.org/10.3390/su13020461 - 6 Jan 2021

Cited by 41 | Viewed by 6277

Abstract

This paper develops a life cycle assessment framework for embodied environmental impacts of building construction systems. The framework is intended to be used early in the design stage to assist decision making in identifying sources of higher embodied impacts and in selecting sustainable [...] Read more.

This paper develops a life cycle assessment framework for embodied environmental impacts of building construction systems. The framework is intended to be used early in the design stage to assist decision making in identifying sources of higher embodied impacts and in selecting sustainable design alternatives. The framework covers commonly used building construction systems such as reinforced concrete construction (RCC), hot-rolled steel construction (HRS), and light steel construction (LSC). The system boundary is defined for the framework from cradle-to-grave plus recycling and reuse possibilities. Building Information Modeling (BIM) and life cycle assessment are integrated in the developed framework to evaluate life cycle embodied energy and embodied greenhouse emissions of design options. The life cycle inventory data used to develop the framework were extracted from BIM models for the building material quantities, verified Environmental Product Declarations (EPD) for the material production stage, and the design of construction operations for the construction and end-of-life stages. Application of the developed framework to a case study of a university building revealed the following results. The material production stage had the highest contribution to embodied impacts, reaching about 90%. Compared with the conventional RCC construction system, the HRS construction system had 41% more life cycle embodied energy, while the LSC construction system had 34% less life cycle embodied energy. When each system was credited with the net benefits resulting from possible recycling/reuse beyond building life, the HRS construction system had 10% less life cycle embodied energy, while the LSC construction system had 68% less life cycle embodied energy. Similarly, the HRS construction system had 29% less life cycle greenhouse gas (GHG) emissions, while the LSC construction system had 62% less life cycle GHG emissions. Sustainability assessment results showed that the RCC construction system received zero Leadership in Energy and Environmental Design (LEED) credit points, the HRS construction system received three LEED credit points, while the LSC construction system received five LEED credit points. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

17 pages, 2893 KiB

Open AccessArticle

Life Cycle Environmental Assessment of Light Steel Framed Buildings with Cement-Based Walls and Floors

by Mona Abouhamad and Metwally Abu-Hamd

Sustainability 2020, 12(24), 10686; https://doi.org/10.3390/su122410686 - 21 Dec 2020

Cited by 12 | Viewed by 4371

Abstract

The objective of this paper is to apply the life cycle assessment methodology to assess the environmental impacts of light steel framed buildings fabricated from cold formed steel (CFS) sections. The assessment covers all phases over the life span of the building from [...] Read more.

The objective of this paper is to apply the life cycle assessment methodology to assess the environmental impacts of light steel framed buildings fabricated from cold formed steel (CFS) sections. The assessment covers all phases over the life span of the building from material production, construction, use, and the end of building life, in addition to loads and benefits from reuse/recycling after building disposal. The life cycle inventory and environmental impact indicators are estimated using the Athena Impact Estimator for Buildings. The input data related to the building materials used are extracted from a building information model of the building while the operating energy in the use phase is calculated using an energy simulation software. The Athena Impact Estimator calculates the following mid-point environmental measures: global warming potential (GWP), acidification potential, human health potential, ozone depletion potential, smog potential, eutrophication potential, primary and non-renewable energy (PE) consumption, and fossil fuel consumption. The LCA assessment was applied to a case study of a university building. Results of the case study related to GWP and PE were as follows. The building foundations were responsible for 29% of the embodied GWP and 20% of the embodied PE, while the CFS skeleton was responsible for 30% of the embodied GWP and 49% of the embodied PE. The production stage was responsible for 90% of the embodied GWP and embodied PE. When benefits associated with recycling/reuse were included in the analysis according to Module D of EN 15978, the embodied GWP was reduced by 15.4% while the embodied PE was reduced by 6.22%. Compared with conventional construction systems, the CFS framing systems had much lower embodied GWP and PE. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

26 pages, 3733 KiB

Open AccessArticle

Abrasive Wear Resistance of Concrete in Connection with the Use of Crushed and Mined Aggregate, Active and Non-Active Mineral Additives, and the Use of Fibers in Concrete

by Lenka Bodnárová, Martin Ťažký, Lucia Ťažká, Rudolf Hela, Ondřej Pikna and Libor Sitek

Sustainability 2020, 12(23), 9920; https://doi.org/10.3390/su12239920 - 27 Nov 2020

Cited by 6 | Viewed by 3068

Abstract

Virtually every concrete structure comes into contact with abrasive effects of flowing media or solids, which have a direct impact on the durability of concrete. An abrasive effect is most pronounced in transport or water management structures, and these structures are often designed [...] Read more.

Virtually every concrete structure comes into contact with abrasive effects of flowing media or solids, which have a direct impact on the durability of concrete. An abrasive effect is most pronounced in transport or water management structures, and these structures are often designed for a significantly longer service life (usually 100 years). This research evaluates the influence of the filler component in terms of the type of aggregate and its mineralogical composition on concrete abrasion resistance. As part of the impact of the binder component, several concrete mixtures were produced using the same aggregate and maintaining the same strength class with the addition of different types of active and inert mineral additives. In other parts of the research, the effect of adding fiber reinforcement on the abrasion resistance of concrete was verified. Mutual connections and correlations in different age groups (7, 28 and 90 days) were sought for all obtained results. The abrasion resistance of the composite was monitored by using standard procedures, especially using a Böhm device. It was found that for good abrasion resistance of concrete, it is not necessary to produce concretes with high strength classes using often expensive mineral additives (microsilica) and quality aggregates, but the maturation time of the composite and its microstructure plays an important role. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

20 pages, 3281 KiB

Open AccessArticle

Sustainability Potential Evaluation of Concrete with Steel Slag Aggregates by the LCA Method

by Vojtěch Václavík, Marcela Ondová, Tomáš Dvorský, Adriana Eštoková, Martina Fabiánová and Lukáš Gola

Sustainability 2020, 12(23), 9873; https://doi.org/10.3390/su12239873 - 25 Nov 2020

Cited by 19 | Viewed by 3400

Abstract

Sustainability in the construction industry refers to all resource-efficient and environmentally responsible processes throughout the life cycle of a structure. Green buildings may incorporate reused, recycled, or recovered materials in their construction. Concrete is as an important building material. Due to the implementation [...] Read more.

Sustainability in the construction industry refers to all resource-efficient and environmentally responsible processes throughout the life cycle of a structure. Green buildings may incorporate reused, recycled, or recovered materials in their construction. Concrete is as an important building material. Due to the implementation of by-products and waste from various industries into its structure, concrete represents a significant sustainable material. Steel slag has great potential for its reuse in concrete production. Despite its volume changes over time, steel slag can be applied in concrete as a cement replacement (normally) or as a substitute for natural aggregates (rarely). This paper focused on an investigation of concrete with steel slag as a substitute of natural gravel aggregate. Testing physical and mechanical properties of nontraditional concrete with steel slag as a substitute for natural aggregates of 4/8 mm and 8/16 mm fractions confirmed the possibility of using slag as a partial replacement of natural aggregate. Several samples of concrete with steel slag achieved even better mechanical parameters (e.g., compressive strength, frost resistance) than samples with natural aggregate. Moreover, a life cycle assessment (LCA) was performed within the system boundaries cradle-to-gate. The LCA results showed that replacements of natural aggregates significantly affected the utilization rate of nonrenewable raw materials and reduced the overall negative impacts of concrete on the environment up to 7%. The sustainability indicators (SUI), which considered the LCA data together with the technical parameters of concrete, were set to evaluate sustainability of the analyzed concretes. Based on the SUI results, replacing only one fraction of natural gravel aggregate in concrete was a more sustainable solution than replacing both fractions at once. These results confirmed the benefits of using waste to produce sustainable materials in construction industry. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

21 pages, 1261 KiB

Open AccessArticle

Environmental Overcost of Single Family Houses in Insular Context: A Comparative LCA Study of Reunion Island and France

by Leslie Ayagapin and Jean Philippe Praene

Sustainability 2020, 12(21), 8937; https://doi.org/10.3390/su12218937 - 27 Oct 2020

Cited by 4 | Viewed by 3854

Abstract

The building and public works sector is, in France as in Europe, a major consumer of raw materials for both the manufacture of products and the construction of buildings and structures. This sector has a direct impact on the natural and built environment. [...] Read more.

The building and public works sector is, in France as in Europe, a major consumer of raw materials for both the manufacture of products and the construction of buildings and structures. This sector has a direct impact on the natural and built environment. This effect is even more pronounced in the case of isolated territories, such as islands. The latter have their own constraints (geographical location, production of the local grid mix) and particularities: very small territory, massive importation of goods in all fields, such as food, automobile, building, and others). In this study, we focus on the building branch of the construction industry, which covers housing (single-family houses and apartment blocks). The study is based on the analysis of about twenty single-family houses built in metropolitan France and Reunion Island. The construction standards for these two regions comply with European standards (CE) and French regulations. However, in the case of Reunion Island, a tropical island, it applies in particular to the Thermal, Acoustic, and Ventilation Regulations for New Buildings in Overseas Departments and Regions (RTAA DROM). The approach that is used for the environmental assessment of single-family homes is the Life Cycle Assessment (LCA), from cradle to grave. The results initially showed that there is an additional environmental cost in the construction sector between France and Reunion Island. This is initially due to the choice of origin of materials and products, which can greatly contribute to the impacts of construction. Secondly, to the use of the countries’ electricity mix, which also contributes, in part, to the impact of the construction of these single-family homes during the assembly and transformation of the products. Finally, this additional cost also differs according to the transport used (sea, air, rail, road). For the Global Warming Potential (GWP) indicator, in our study we note that the additional environmental cost is 37% higher in Reunion Island. This figure explains the additional impact of the 218 kg-

{CO}_{2 eq} / m^{2}

of built-up area built for Reunion Island. This study is one of the first analyses demonstrating the additional environmental cost that exists between mainland France and overseas France. Thus, the results demonstrate the importance of creating a specialized and regionalized database for the case of remote islands. Thus, this database would allow for professionals to have a precise environmental assessment, not on a national but on a regional scale. This document also provides a framework and guideline for policy decision-making in the overseas islands. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Graphical abstract

14 pages, 5476 KiB

Open AccessArticle

A Prolongation of the Service Life of Cement-Based Composites by Controlling the Development of Their Strength and Volume Changes

by Peter Briatka, Peter Makýš and Jozef Gašparík

Sustainability 2020, 12(20), 8479; https://doi.org/10.3390/su12208479 - 14 Oct 2020

Cited by 2 | Viewed by 1542

Abstract

As several studies and authors have already proved, the curing of fresh concrete affects the development of its strength and volume changes, which goes hand in hand with the durability and service life of concrete structure. Several studies concerning internal curing (IC) have [...] Read more.

As several studies and authors have already proved, the curing of fresh concrete affects the development of its strength and volume changes, which goes hand in hand with the durability and service life of concrete structure. Several studies concerning internal curing (IC) have also been published. They were dedicated to identifying the action of IC by Differential Thermal Analysis (DTA), especially for mixes with low w/c ratios. Some studies have presented various approaches for the design of mixes with IC. Some discrepancies between conventional designs and reality have been identified. A significant one is the calculation of water losses. The initial (conventional) approach defined water losses based on Menzel’s equation. However, in reality, it is valid for only the first few hours. As water losses are essential to an appropriate design of IC, we will demonstrate in this paper the effect of IC on the development of changes in the volume and strength of cement-based composites. Both parameters come into mutual interaction during actual construction and affect the internal stresses of the structure/matrix, which may lead to the formation and development of cracks. The general goal is to mitigate cracks and, thus, prolong the concrete’s service life, which may be achieved by controlling the development of changes in volume along with the development of strength, e.g., by IC. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

28 pages, 4215 KiB

Open AccessArticle

Evaluation of Family Houses in Slovakia Using a Building Environmental Assessment System

by Eva Krídlová Burdová, Iveta Selecká, Silvia Vilčeková, Dušan Burák and Anna Sedláková

Sustainability 2020, 12(16), 6524; https://doi.org/10.3390/su12166524 - 12 Aug 2020

Cited by 4 | Viewed by 2569

Abstract

The presented study is focused on the verification of a Building Environmental Assessment System (BEAS). A total of 13 detached family houses representing typical construction sites in Slovakia were chosen for analysis, evaluation and certification by using a BEAS which contains several main [...] Read more.

The presented study is focused on the verification of a Building Environmental Assessment System (BEAS). A total of 13 detached family houses representing typical construction sites in Slovakia were chosen for analysis, evaluation and certification by using a BEAS which contains several main fields: A—Site Selection and Project Planning; B—Building Construction; C—Indoor Environment; D—Energy Performance; E—Water Management; and F—Waste Management. The results of this study show that the current construction method for family houses does not respect the criteria of sustainable construction as much as it possibly can. The reason for this is that investment costs for construction are prioritized over environmental and social aspects. Therefore, one house with a score of 1.10 is certified as BEAS BRONZE, ten family houses with scores of 1.56–2.88 are certified as BEAS SILVER and only two family houses with total scores of 3.59 and 3.87, respectively, are certified as BEAS GOLD. The overall results show that the weakest fields of sustainability are Waste management, Energy performance and Building construction. The best-rated fields are Site Selection and Project Planning, Indoor Environment and Water Management. In the future, it is essential to pay attention to those areas where the sustainability criteria have not been reached, as well as to raise project teams’ awareness of sustainability issues and subsequently to transfer them to building practices. Full article

(This article belongs to the Special Issue Sustainable Building Materials and Life Cycle Assessment (LCA))

► Show Figures

Figure 1

Journal Menu

Journal Browser

Sustainable Building Materials and Life Cycle Assessment (LCA)

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Benefits of Publishing in a Special Issue

Published Papers (8 papers)

Editorial

Research

Further Information

Guidelines

MDPI Initiatives

Follow MDPI