Next Article in Journal
Optimization of the Surface Roughness and Chip Compression Ratio of Duplex Stainless Steel in a Wet Turning Process Using the Taguchi Method
Next Article in Special Issue
Experimental Investigation and NSGA-III Multi-Criteria Optimization of 60CrMoV18-5 Cold-Work Tool Steel Machinability Under Dry CNC Hard Turning Conditions
Previous Article in Journal
An Accurate and Rapid Docking Algorithm for Four-Way Shuttle in High-Density 3D Warehousing Environment
Previous Article in Special Issue
Optimizing Machining Efficiency in High-Speed Milling of Super Duplex Stainless Steel with SiAlON Ceramic Inserts
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Machines
Volume 12
Issue 7
10.3390/machines12070436
machines-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles thumb_up
...
Endorse textsms
...
Comment
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments

by
Tufan Zerooğlu
1,
Ünal Değirmenci
2,* and
Serhat Şap
3,*
1
Department of Mechanical Engineering, Bingöl University, 12000 Bingöl, Türkiye
2
Department of Machinery and Metal Technologies, Bingöl University, 12000 Bingöl, Türkiye
3
Department of Electricity and Energy, Bingöl University, 12000 Bingöl, Türkiye
*
Authors to whom correspondence should be addressed.
Machines 2024, 12(7), 436; https://doi.org/10.3390/machines12070436
Submission received: 31 May 2024 / Revised: 22 June 2024 / Accepted: 23 June 2024 / Published: 26 June 2024
(This article belongs to the Special Issue Recent Advances in Surface Integrity with Machining and Milling)
Browse Figures
Versions Notes

Abstract

:
AISI 5140 steel is an alloy frequently used in the manufacturing and automotive industries. This steel alloy is shaped using different manufacturing methods and cooling is required during this process. This research study included the milling of AISI 5140 steel utilizing various cutting settings and cooling/lubrication procedures. For this purpose, two cutting speeds (75–100 m/min), two feed rates (0.075–0.100 mm/rev), and four cooling media (dry, MQL, flood, nanofluid) were used. Then, 5% Mo nanoparticles were added to the nanofluid cutting fluid. Machinability and power consumption analyses were carried out using the input parameters selected in light of the manufacturer’s recommendations and studies in the literature. The effects of sustainable cutting fluids and their parameters on machinability and power consumption were investigated through experiments. This study concluded that the use of nanofluid led to improvements in surface roughness, flank wear, and power consumption characteristics. It was determined that the flood environment is the most effective in reducing the cutting temperature. As a result, it is predicted that nanofluid cutting fluids can be used during machining.

1. Introduction

In today’s world where technology is rapidly developing, the processing of high-performance materials for industrial applications is of critical importance in terms of the efficiency and quality of production processes [1]. In this context, metalworking operations require controlling various parameters that arise while processing the material. Some of these parameters directly affect outputs such as machinability features and energy consumption [2]. Material machinability is a crucial determinant of production process efficiency and end-product quality in the metalworking industry [3]. Particularly in difficult-to-machine materials such as high-strength steels, appropriate cooling techniques can significantly affect machining performance [4,5].
One of the important materials that need to be investigated in terms of machining performance is AISI 5140 steel. AISI 5140 steel consists of alloy components that provide high strength, hardness, and wear resistance [6,7]. This material is generally used in tools such as bearings, gears, shafts, gearboxes, axles, pipe and rod applications requiring high strength and hardness, screwdriver bits, and drill bits due to its suitability for hot processing and moderate weldability [8]. The high chromium concentration in the chemical composition of this steel, known as manufacturing steel for its many applications, might provide challenges in terms of its machinability [9]. Due to the mechanical [10], chemical [11,12], and thermal effects occurring during the processing of this material, surface roughness (Ra) and tool wear are inevitable. When evaluating tool life in the context of machining, flank and crater wear are frequently the primary types of tool wear considered [13]. Several research studies on AISI 5140 steel may be found in the literature. Kahraman [14] utilized the Taguchi method to analyze the turning performance of AISI 5140 steel and determine the most effective cutting parameters for reducing surface irregularity. A minimum Ra could be achieved under the following conditions: a cutting depth of 0.5 mm, a feed rate (fn) of 0.2 mm/rev, and a rotation speed of 2000 rpm. An investigation was undertaken by Aslan [15] to assess the effects of various machining parameters such as depth of cut, cutting speed (Vc), fn, cutting force on cutting tool tip side attrition, vibration levels, and cutting force. The analysis of variance (ANOVA) method was used in the investigation. Consequently, it was discovered that the occurrence of vibration and cutting pressures during the turning process has a substantial impact on Vb. In another study, Grzesik and Wanat [16] conducted a research study where they analyzed the roughness of the surface of a component during the continuous cylindrical dry turning of AISI 5140 steel. The results suggest that hard turning produces unique surface profiles and microstructures, exhibiting Ra values of approximately 0.25 mm, which are comparable to the outcomes obtained through post-grinding. Kuntoğlu et al. [17] examined the vibration and Ra characteristics of AISI 5140 steel by employing the response surface approach. The optimal cutting conditions were ascertained through the manipulation of cutting velocities, fn, and cutting edge angles. The results of the study revealed that the most significant influence on the increase in axial vibration (65.8%) and surface irregularity (69.4%) was the input rate. The primary determinants of radial vibration (75.5%) and tangential vibration, conversely, were the cutting edge angle and Vc.
The effects of using different cooling/lubrication (c/l) conditions during machining on machining performance are also an important research topic [18]. Usca et al. [19] examined the machining properties of AISI 5140 steel under various c/l conditions, including dry, minimum quantity lubrication (MQL), and cryogenic liquid nitrogen (cryo-LN2). As a result, Cryo-LN2 gave good results in all machinability parameters compared to dry media. Kara et al. [20] investigated the efficiency of the cooling and cutting parameters that were used in the cylindrical grinding process of AISI 5140 steel. According to their research, the cryogenically treated samples achieved the most favorable Ra. In another study, Yıldırım et al. [21] evaluated the effects of a dry environment, traditional cutting fluid, and MQL system. They concluded that lowering the use of cutting fluid resulted in improved machining performance. In recent years, the use of nanofluids as a c/l environment has provided significant improvements in machinability and processing efficiency. It has been observed that cooling lubricants containing nanoparticles may have higher specific surface areas and heat transfer coefficients compared to pure cutting oils [22,23]. Nanoparticles have the ability to decrease the amount of friction between surfaces and enhance resistance to wear by forming a thin layer of a lubricating coating [24,25,26,27]. Nanoparticles can exhibit a more stable performance at high temperatures, which may be advantageous due to the high temperatures that occur during processing [28]. Consequently, they enhance the lubricating effectiveness and tribological characteristics of the coolant [29,30]. Yıldırım [31] investigated the machinability of AISI 420 steel under a nanofluid cutting fluid and a cryogenic coolant containing 0.5% graphene nanoplates by volume. Consequently, the study determined that cryogenic cooling outperformed the nanofluid in terms of surface temperature, chip shape, tool life, and tool wear. However, the nanofluid exhibited superior performance in Ra and surface topography. Maruda et al. [32] examined the machining performances of Ti6Al4V Titanium alloy by performing the turning process in different c/l environments such as dry machining, pure MQL technique, and MQL technique with the addition of copper nanoparticles. They stated that after the addition of copper nanoparticles of different sizes, the least tool crater and side wear occurred in the MQL environment with the smallest copper addition, and that this gave better results compared to dry and pure MQL. In another study, Yıldırım et al. [33] investigated the machinability of nickel-based Hastelloy C4 alloy in three different vegetable oil environments with the addition of TiO2 and SiO2 nanoparticles. As a result, it was found that machining with corn oil and TiO2 nanofluid provided a 58.57%, 53.18%, 36.1%, and 34.88% improvement in Ra, tool wear, power consumption (Pd), and cutting temperature (Tc), respectively, compared to dry machining. Makkesana et al. [34] examined the impact of incorporating graphite and molybdenum disulfide into a nanofluid–MQL system on tool wear, machinability, and microhardness during the machining of Inconel 625. While sunflower oil with MoS2 produced better Ra results than other conditions, it was noted that nano MQL had beneficial outcomes in terms of tool wear and Tc.
According to the literature, the process of machining materials causes a substantial rise in temperature in the cutting area, which plays a crucial role in determining the quality of the product. Despite the widespread use of traditional cutting fluids for heat dissipation in machining, they pose a significant risk to the environment and the well-being of workers. Hence, it is important to ascertain eco-friendly and user-centric substitutes for conventional cutting fluids. Within this framework, nanoparticles are believed to provide a potential solution to issues related to Ra and temperature management by facilitating the creation of a protective coating during material processing. Although there are partial studies on the machinability of AISI 5140 steel in the literature, there are no studies on its machining performance under nanofluid cooling fluids containing nanoparticles. Therefore, in this study, output parameters such as tool wear, Ra, Tc, and energy consumption during the milling of AISI 5140 steel were investigated using a new nanofluid coolant with molybdenum additives and compared with machining parameters under different c/l conditions.

2. Materials and Methods

2.1. Workpiece and Cutting Tools

In this experimental study, AISI 5140 manufacturing steel was used as the workpiece. The metal industry often utilizes AISI 5140 steel due to its notable strength and hardness characteristics. AISI 5140 steel has a hardness of 238 HB, a tensile strength of 804 N/mm2, and an elongation at break of 21%. All test samples were cut into Ø50 × 20 mm dimensions and made ready for milling. Table 1 displays the chemical makeup of the samples.
Coded HM 90 APKT 1003PDR IC908 inserts from Iscar, located in Konya, Türkiye, were used for the milling process. The cutting tool was coated with AlTiN by the physical vapor deposition (PVD) method and had a dark grey color. The insert, which had a corner radius of 0.8 mm, was affixed to a milling cutter with the designation ST90 AP10 D12 W12 L120 Z01 (Smoxh, Konya, Turkey). Inserts were substituted at the conclusion of each trial.

2.2. Machining Center and Experimental Stages

The studies were conducted using a 3-axis Dahlih MCV-860 milling machine from Dahlih in Taichung, Taiwan. The milling machine had a power capacity of 7.5 kW. The experiments were devised based on a comprehensive experimental framework, resulting in a total of 16 planned experiments. In the experimental design, 2 different Vcs (75–100 m/min), 2 different fns (0.075–0.100 mm/rev), and 4 different c/l environments were selected. The experimental design is shown in Table 2. The cutting settings were established and scheduled in accordance with the manufacturer’s guidelines and first testing. Before the experiments, the surfaces were cleaned by removing a layer from each sample for fair results. The “Zig” tool path and downward milling approach were implemented while maintaining a constant cutting depth of 0.5 mm. The experimental scheme is given in Figure 1.

2.3. Cooling/Lubrication Environments

Experiments were planned in 4 different c/l environments (dry, MQL, flood, and Mo-based nanofluid) to determine optimum machinability performance during milling. The dry processing environment is evaluated within the scope of sustainability [35]. The coolant was transmitted to the cutting zone from a nozzle connected to the machine tool with a flood c/l environment. In MQL and nanofluid c/l environments, a Werte Micro STN-15 (Kar-Tes, Istanbul, Turkey) model system was used. The pressure used in the system was determined as 6 bar and the liquid flow rate was determined as 35 mL/h. The 3 mm diameter nozzle connected to the system was positioned at a distance of approximately 200 mm from the test sample. KT2000 synthetic oil with a hydrodynamic lubrication feature was used as the cutting fluid in the MQL environment. In the nanofluid environment, Mo nanoparticles were added to KT2000 synthetic oil. Mo nanoparticles were purchased from the manufacturer (Nanokar, Istanbul, Türkiye). Technical details of Mo nanoparticles are provided in Table 3. The preparation process of the nanofluid is given in detail in Figure 2.
Cutting fluids were created by adding Mo nanoparticles into KT2000 synthetic oil at a rate of 0.5 wt.%. A total of 500 mL of nanofluid was prepared for each cutting environment. Nanoparticles were added into synthetic oil and blended in a mechanical mixer for approximately 5 min. It was then mixed by ultrasonic sonication for approximately 30 min.

2.4. Measuring Instruments

An investigation was conducted to examine the impact of cutting parameters and cutting/lubrication conditions on the milling process of AISI 5140 steel. Analyzed in this particular context were machinability properties and Pd. Insize ISR-C100 Ra equipment, located in Beijing, China, was used to assess the surface quality. Five measurements were collected from various parts of each sample, and the average Ra values were recorded. The temperatures in the cutting zone were measured using a Testo 871 thermal camera model (Testo, Istanbul, Turkey). The distance between the cutting zone and the thermal camera is 400 mm. An Insize ISM PM200SB optical microscope model manufactured in Suzhou New District, China, was used to identify any defects present on the lateral edges of the cutting tool. SEM, EDS, and mapping investigations conducted on a JEOL JSM 6510 SEM instrument (Jeol, Tokyo, Japan) successfully identified the wear processes taking place on the cutting tool. The HIOKI PW 3198 power analyzer, which was made by Hioki in Nagano, Japan, was used in order to determine the milling machine’s power usage. The amount of power consumed was calculated using the data obtained from the device using special software. A diagram representing the wear mechanisms is given in Figure 3.

3. Results and Discussions

In this experimental study, machinability (surface roughness, tool wear, and cutting temperature) and power consumption analyses of AISI 5140 manufacturing steel under different c/l conditions (dry, MQL, flood, and nanofluid) were carried out. The results are given below.

3.1. Surface Roughness Analysis

Surface quality is considered an important machinability performance criterion in machining processes. It is necessary to perform Ra evaluation after machining and to observe the effects of different cutting parameters [31]. This portion of the study included conducting tests to assess the impact of various characteristics on surface quality. Figure 4 displays the experimental findings visually. When considering cooling fluids, nanofluid is shown to be the optimal choice. When the Vc was set at 75 m/min, using a nanofluid environment resulted in Ra improvements of about 36.7% and 34% at an fn of 0.075 and 0.100 mm/rev, respectively, compared to the dry environment. At a Vc of 100 m/min, the use of nanofluid resulted in Ra improvements of about 27.7% and 35.4% at an fn of 0.075 and 0.100 mm/rev, respectively, compared to the dry environment. The minimum Ra, measuring 0.684 µm, was achieved when the Vc was set at 100 m/min, the fn was set at 0.075, and the cutting process was conducted in a nanofluid environment. The superiority of the nanofluid cooling fluid compared to other environments is related to the lubrication quality of the nanofluid. Nanofluid cutting fluids exhibit better wettability properties compared to other cutting fluids. This creates a film layer that helps reduce friction in the cutting area [37]. In the Mo-containing nanofluid cutting fluid, oil-coated nanoparticles are transferred from the nozzle to the cutting zone as a fine mist cloud. Thus, the mist cloud that easily enters the cutting zone protects the form of a thin film layer, increasing the wear performance and therefore increasing the surface quality.
The graph clearly demonstrates that there is a direct correlation between feed speed and Ra, indicating that as the feed speed rises, the Ra also increases. According to the literature, the fn is the most influential factor in determining surface quality. It has been shown that increasing the feed speed leads to an increase in Ra [38]. Khalilpourazary and Meshkat [39] reported that nanoparticle-added coolant showed better c/l performance, thus reducing Ra. Hegab et al. [40] reported in a study that the surface quality increased thanks to the wettability, convection, and conduction advantages of nanofluids.
Surface topography is a very important argument in terms of understanding surface quality. Because it has a direct effect on parameters such as wear and fatigue [41,42]. Figure 5 analyzes surface topographies under various cutting conditions, namely a Vc of 75 m/min and an fn of 0.075 mm/rev. The Ra in the dry environment was measured to be 1.268 µm. In the MQL, flood, and nanofluid conditions, the recorded Ra values were 0.926 µm, 1.143 µm, and 0.802 µm, respectively. The nanofluid environment yielded the lowest Ra rating. The surface roughness in the nanofluid environment exhibits a higher degree of regularity in comparison to other environments.

3.2. Flank Wear Analysis

Tool wear is a feature that has a significant impact on all machinability parameters. Therefore, a detailed examination of tool wear analysis is very important [43,44]. Extended tool lifespan decreases both the cost of cutting tools and the duration required for tool replacement. This research study examined the impact of two different Vcs, two fns, and four cooling conditions on the amount of wear experienced on the flank of the tool. A grand total of 16 tests were conducted, with a distinct state-of-the-art cutting edge being used for each individual experiment. The degree of erosion on the cutting tool edge was quantified and documented using an optical microscope. Figure 6 illustrates the impact of various cutting settings and cutting circumstances on Vb. The nanofluid environment is shown to decrease Vb in comparison to other settings. When the Vc was set at 75 m/min, using a nanofluid environment resulted in a reduction in Vb of roughly 24% and 27% at an fn of 0.075 and 0.100 mm/rev, respectively, compared to the dry environment. When the Vc was adjusted to 100 m/min, substituting a nanofluid environment for a dry environment led to a decrease in Vb of about 26% and 22% at an fn of 0.075 and 0.100 mm/rev, respectively. A Vc of 75 m/min, an fn of 0.100, and a nanofluid environment resulted in a minimum Vb measurement of 0.301 mm. Wear may be directly attributed to elevated temperatures and heightened friction in the cutting area. The cooling liquids used in this study were effective in reducing temperatures. However, in this study, minimum wear values were obtained with the nanofluid cooling method. Additionally, it was observed that Vb increased with increasing Vc, and Vb decreased with increasing feed speed. It was determined that these results are compatible with the literature [45,46,47].
Tool wear arises during the process of machining as a result of plastic deformation and high levels of friction between the cutting tool and the material [48]. At this stage, different loads affect wear mechanisms depending on thermal, mechanical, and chemical properties. These loads cause wear mechanisms to occur in different parts of the cutting tool over time [49]. The wear mechanisms occurring in this study can be listed as nose wear, cutting tool peeling, and adhesion. SEM pictures of the cutting tool under various cutting settings are shown in Figure 7, with a Vc of 75 m/min and an fn of 0.075 mm/rev. The forms of wear that manifest on the cutting tool are observed under identical cutting and feed velocities. Notch wear and flank wear were seen in dry circumstances. Additionally, flank wear was detected in the MQL, flood, and nanofluid environments. The nanofluid environment yielded the lowest flank wear value when the Vc and fn were kept constant. In addition, as shown in Figure 8, an EDS analysis of the cutting tool used in the MQL environment was performed and the materials contaminated by the workpiece on the tool were detected as adhesion.
Figure 9 shows the cutting tool mapping analysis and backscattered images obtained as a result of machining in a dry environment. The figure shows an overview of the cutting tool, mapping, and element analysis in percentages. As understood from the EDS analysis, it was observed that the coating was peeled off from the cutting tool in dry machining and the presence of the main elements of the cutting tool was observed in the peeled parts.

3.3. Cutting Temperature Analysis

The temperatures in the cutting zone play a vital role in determining the tribological performance and dimensional accuracy of the cutting tool. Furthermore, the temperatures in the cutting zone possess the capability to influence the surface integrity of the workpiece [50]. In other words, the temperatures formed between the cutting tool and the chip surface are important for quality machining and productivity. For this reason, the analysis of temperatures occurring during cutting should be considered in detail [51]. Figure 10 demonstrates the influence of different cutting settings and cutting circumstances on the temperature during cutting. Based on the trials, it was concluded that the flood environment demonstrated superior cooling in comparison to other cutting settings. It has been noted that the flood environment yields superior outcomes in all cutting parameters. According to the average temperatures, it was found that temperatures in the flood environment decreased by around 56.5% compared to the dry environment. This condition may be attributed to the fact that the cutting fluid, when used as flood cooling, delivers enhanced cooling to the cutting zone. The flood cooling strategy can affect Tc depending on many parameters such as Vc, fn, tool geometry, and the workpiece. When evaluated in terms of Vc, it was seen that it gives better results at low speeds compared to high speeds. In terms of fn, lower Tcs were obtained at high feed speeds compared to low feed speeds. Optimal cooling may be achieved by regulating the temperatures between the cutting tool and the surface of the chip [52]. The Tc reached its lowest point of 61.4 °C when the Vc was set to 75 m/min, the fn was 0.100 mm/rev, and the cutting operation was conducted in a flood environment. Figure 11 shows thermal images taken during processing.

3.4. Power Consumption Analysis

Energy consumption occurs in machining processes during basic manufacturing operations [53]. Machining, one of the most important technologies in the manufacturing sector, has made significant contributions to the development of the economy. Research has been conducted on many factors in the machining industry, such as cutting tools, c/l techniques, and cutting parameters [54,55]. During the course of this study, significant efforts were undertaken to develop a procedure that is both cost-effective and ecologically sustainable. Concurrently with technological advancements, Vc in cutting instruments is seeing substantial increases. Therefore, elevated temperatures at the interface between the tool and the chip decrease the lifespan of expensive cutting tools and impact the quality of the workpiece’s surface. This scenario results in the depletion of resources and loss of products in the metal processing sector. Coolants may enhance surface quality and prolong cutting tool lifespan in the metal cutting sector while treating steels. Nevertheless, the use of petroleum-derived cutting fluids, which now predominates, may lead to significant and irreversible issues in terms of both economic impact and human well-being. This section examines the impact of various cutting fluids and cutting settings on energy usage, as shown in Figure 12. Nanofluid was shown to be the most effective cooling medium in terms of power usage across all cutting parameters. When the Vc was set at 75 m/min, using a nanofluid environment resulted in Pd reductions of roughly 2% and 3% at an fn of 0.075 and 0.100 mm/rev, respectively, compared to the dry environment. Based on a Vc of 100 m/min, an improvement of approximately 4.6% and 1% in Pd was achieved, respectively, at an fn of 0.075 and 0.100 mm/rev in the nanofluid environment compared to the dry environment. The lowest Pd value (743 W) was obtained at 100 m/min Vc, 0.100 feed speed, and in a nanofluid environment. In terms of Vc, increasing Vc caused a decrease in Pd. Similarly, Pd tends to decrease with increasing feed speed. Makhesana et al. [34] used MoS2 and graphite-reinforced nanofluids as cutting fluids during the machining of nickel-based superalloys. As a result, they reported that MoS2-doped nanofluid reduces Pd. A study by Usca [46] reported that cellulose nanocrystal-based nanofluid cutting fluid was used as a coolant during the machining of Dillimax 690T. According to that report, higher cutting and feed speeds result in decreased power usage.

4. Conclusions

This research study aimed to explore the machinability qualities of AISI 5140 steel, which is often used in the industrial sector. The investigation included analyzing the steel’s performance under various cutting settings and cooling procedures. The results are given below.
  • Nanofluid was identified as the optimal medium for Ra. The lowest Ra obtained was 0.684 µm under the conditions of a Vc of 100 m/min, an fn of 0.075, and cutting performed in a nanofluid environment.
  • It was shown that the presence of nanofluid leads to a decrease in Vb in comparison to other conditions. The minimum Vb measurement (0.301 mm) was achieved by using a Vc of 75 m/min, an fn of 0.100, and a nanofluid environment.
  • Based on the mean temperatures, it was concluded that temperatures decreased by around 56.5% in the flood environment compared to the dry environment. The Tc was minimized to 61.4 °C by using a Vc of 75 m/min, an fn of 0.100 mm/rev, and a flood environment.
  • The best cooling environment for Pd in all cutting parameters was determined to be nanofluid. In terms of Vc, increasing Vc caused a decrease in Pd. Similarly, Pd tended to decrease with increasing feed speed.

Author Contributions

Conceptualization, T.Z., Ü.D. and S.Ş.; Data curation, T.Z., Ü.D. and S.Ş.; Formal analysis, T.Z., Ü.D. and S.Ş.; Investigation, T.Z., Ü.D. and S.Ş.; Methodology, T.Z., Ü.D. and S.Ş.; Project administration, Ü.D.; Software, T.Z., Ü.D. and S.Ş.; Supervision, Ü.D.; Validation, T.Z., Ü.D. and S.Ş.; Visualization, T.Z., Ü.D. and S.Ş.; Writing—original draft, T.Z., Ü.D. and S.Ş.; Writing—review and editing, T.Z., Ü.D. and S.Ş. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Data Availability Statement

Data are contained within the article.

Acknowledgments

This article was produced based on Tufan Zerooğlu’s master’s thesis.

Conflicts of Interest

The author declare no conflicts of interest.

References

  1. Şirin, Ş.; Sarıkaya, M.; Yıldırım, Ç.V.; Kıvak, T. Machinability performance of nickel alloy X-750 with SiAlON ceramic cutting tool under dry, MQL and hBN mixed nanofluid-MQL. Tribol. Int. 2021, 153, 106673. [Google Scholar] [CrossRef]
  2. Değirmenci, Ü.; Usca, Ü.A.; Şap, S. Machining characterization and optimization under different cooling/lubrication conditions of Al-4Gr hybrid composites fabricated by vacuum sintering. Vacuum 2023, 208, 111741. [Google Scholar] [CrossRef]
  3. Fernando, W.L.R.; Karunathilake, H.P.; Gamage, J.R. Strategies to reduce energy and metalworking fluid consumption for the sustainability of turning operation: A review. Clean. Eng. Technol. 2021, 3, 100100. [Google Scholar] [CrossRef]
  4. Leksycki, K.; Feldshtein, E.; Maruda, R.W.; Khanna, N.; Królczyk, G.M.; Pruncu, C.I. An insight into the effect surface morphology, processing, and lubricating conditions on tribological properties of Ti6Al4V and UHMWPE pairs. Tribol. Int. 2022, 170, 107504. [Google Scholar] [CrossRef]
  5. Usca, Ü.A.; Şap, S.; Uzun, M.; Değirmenci, Ü. Assessment of the machinability and energy consumption characteristics of Cu–6Gr hybrid composites under sustainable operating. J. Braz. Soc. Mech. Sci. Eng. 2024, 46, 221. [Google Scholar] [CrossRef]
  6. Ryabchikov, A.; Sivin, D.; Ananin, P.; Ivanova, A.; Lopatin, I.; Korneva, O.; Shevelev, A. High intensity, low ion energy implantation of nitrogen in AISI 5140 alloy steel. Surf. Coat. Technol. 2018, 355, 129–135. [Google Scholar] [CrossRef]
  7. Kuntoğlu, M.; Acar, O.; Gupta, M.K.; Sağlam, H.; Sarikaya, M.; Giasin, K.; Pimenov, D.Y. Parametric Optimization for Cutting Forces and Material Removal Rate in the Turning of AISI 5140. Machines 2021, 9, 90. [Google Scholar] [CrossRef]
  8. Gao, K.; Qin, X.; Wang, Z.; Zhu, S. Effect of spot continual induction hardening on the microstructure of steels: Comparison between AISI 1045 and 5140 steels. Mater. Sci. Eng. A 2016, 651, 535–547. [Google Scholar] [CrossRef]
  9. Kuntoğlu, M.; Aslan, A.; Sağlam, H.; Pimenov, D.Y.; Giasin, K.; Mikolajczyk, T. Optimization and Analysis of Surface Roughness, Flank Wear and 5 Different Sensorial Data via Tool Condition Monitoring System in Turning of AISI 5140. Sensors 2020, 20, 4377. [Google Scholar] [CrossRef]
  10. Sepet, H.; Tarakcioglu, N.; Misra, R.D.K. Investigation of mechanical, thermal and surface properties of nanoclay/HDPE nanocomposites produced industrially by melt mixing approach. J. Compos. Mater. 2015, 50, 3105–3116. [Google Scholar] [CrossRef]
  11. Aslan, A.; Salur, E.; Gunes, A.; Sahin, O.S.; Karadag, H.B.; Akdemir, A. The mechanical properties of composite materials recycled from waste metallic chips under different pressures. Int. J. Environ. Sci. Technol. 2019, 16, 5259–5266. [Google Scholar] [CrossRef]
  12. Sepet, H.; Tarakcioglu, N.; Misra, R.D.K. Effect of inorganic nanofillers on the impact behavior and fracture probability of industrial high-density polyethylene nanocomposite. J. Compos. Mater. 2017, 52, 2431–2442. [Google Scholar] [CrossRef]
  13. Usca, Ü.A.; Şap, S.; Uzun, M. Evaluation of Machinability of Cu Matrix Composite Materials by Computer Numerical Control Milling under Cryogenic LN2 and Minimum Quantity Lubrication. J. Mater. Eng. Perform. 2023, 32, 2417–2431. [Google Scholar] [CrossRef]
  14. Kahraman, F. Optimization of cutting parameters for surface roughness in turning of studs manufactured from AISI 5140 steel using the Taguchi method. Mater. Test. 2017, 59, 77–80. [Google Scholar] [CrossRef]
  15. Aslan, A. Optimization and analysis of process parameters for flank wear, cutting forces and vibration in turning of AISI 5140: A comprehensive study. Measurement 2020, 163, 107959. [Google Scholar] [CrossRef]
  16. Grzesik, W.; Wanat, T. Comparative assessment of surface roughness produced by hard machining with mixed ceramic tools including 2D and 3D analysis. J. Mater. Process. Technol. 2005, 169, 364–371. [Google Scholar] [CrossRef]
  17. Kuntoğlu, M.; Aslan, A.; Pimenov, D.Y.; Giasin, K.; Mikolajczyk, T.; Sharma, S. Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel. Materials 2020, 13, 4242. [Google Scholar] [CrossRef]
  18. Mia, M.; Gupta, M.K.; Singh, G.; Królczyk, G.; Pimenov, D.Y. An approach to cleaner production for machining hardened steel using different cooling-lubrication conditions. J. Clean. Prod. 2018, 187, 1069–1081. [Google Scholar] [CrossRef]
  19. Usca, Ü.A.; Uzun, M.; Şap, S.; Giasin, K.; Pimenov, D.Y.; Prakash, C. Determination of machinability metrics of AISI 5140 steel for gear manufacturing using different cooling/lubrication conditions. J. Mater. Res. Technol. 2022, 21, 893–904. [Google Scholar] [CrossRef]
  20. Kara, F.; Köklü, U.; Kabasakaloğlu, U. Taguchi optimization of surface roughness in grinding of cryogenically treated AISI 5140 steel. Mater. Test. 2020, 62, 1041–1047. [Google Scholar] [CrossRef]
  21. Yıldırım, Ç.V.; Kıvak, T.; Sarıkaya, M.; Erzincanlı, F. Determination of MQL Parameters Contributing to Sustainable Machining in the Milling of Nickel-Base Superalloy Waspaloy. Arab. J. Sci. Eng. 2017, 42, 4667–4681. [Google Scholar] [CrossRef]
  22. Singh, R.K.; Sharma, A.K.; Dixit, A.R.; Tiwari, A.K.; Pramanik, A.; Mandal, A. Performance evaluation of alumina-graphene hybrid nano-cutting fluid in hard turning. J. Clean. Prod. 2017, 162, 830–845. [Google Scholar] [CrossRef]
  23. Sinha, M.K.; Madarkar, R.; Ghosh, S.; Rao, P.V. Application of eco-friendly nanofluids during grinding of Inconel 718 through small quantity lubrication. J. Clean. Prod. 2017, 141, 1359–1375. [Google Scholar] [CrossRef]
  24. Zadafiya, K.; Shah, P.; Shokrani, A.; Khanna, N. Recent advancements in nano-lubrication strategies for machining processes considering their health and environmental impacts. Manuf. Process 2021, 68, 481–511. [Google Scholar] [CrossRef]
  25. Bakalova, T.; Svobodová, L. Quality assessment of milling technology and the biocidal effects of SiO2 or TiO2 nanoadditives in cooling lubricant emulsions. Manuf. Process 2019, 45, 509–519. [Google Scholar] [CrossRef]
  26. Wang, X.; Li, C.; Zhang, Y.; Ding, W.; Yang, M.; Gao, T.; Cao, H.; Xu, X.; Wang, D.; Said, Z.; et al. Vegetable oil-based nanofluid minimum quantity lubrication turning: Academic review and perspectives. Manuf. Process 2020, 59, 76–97. [Google Scholar] [CrossRef]
  27. Chinchanikar, S.; Kore, S.S.; Hujare, P. A review on nanofluids in minimum quantity lubrication machining. Manuf. Process 2021, 68, 56–70. [Google Scholar] [CrossRef]
  28. Günan, F.; Kıvak, T.; Yıldırım, Ç.V.; Sarıkaya, M. Performance evaluation of MQL with AL2O3 mixed nanofluids prepared at different concentrations in milling of Hastelloy C276 alloy. J. Mater. Res. Technol. 2020, 9, 10386–10400. [Google Scholar] [CrossRef]
  29. Şirin, Ş.; Kıvak, T. Performances of different eco-friendly nanofluid lubricants in the milling of Inconel X-750 superalloy. Tribol. Int. 2019, 137, 180–192. [Google Scholar] [CrossRef]
  30. Maruda, R.W.; Arkusz, K.; Szczotkarz, N.; Wojciechowski, S.; Niesłony, P.; Królczyk, G.M. Analysis of size and concentration of nanoparticles contained in cutting fluid during turning of 316 L steel in minimum quantity lubrication conditions. Manuf. Process 2023, 87, 106–122. [Google Scholar] [CrossRef]
  31. Yıldırım, Ç.V. Investigation of hard turning performance of eco-friendly cooling strategies: Cryogenic cooling and nanofluid based MQL. Tribol. Int. 2020, 144, 106127. [Google Scholar] [CrossRef]
  32. Maruda, R.W.; Szczotkarz, N.; Michalski, M.; Arkusz, K.; Wojciechowski, S.; Niesłony, P.; Khanna, N.; Królczyk, G.M. Evaluation of tool wear during turning of Ti6Al4V alloy applying MQL technique with Cu nanoparticles diversified in terms of size. Wear 2023, 532–533, 205111. [Google Scholar] [CrossRef]
  33. Yıldırım, Ç.V.; Şirin, Ş.; Kıvak, T.; Ercan, H.; Sarıkaya, M. An attempt towards green machining of Ni-based Hastelloy C4 alloy: Effect of vegetable oils and their combination with TiO2 and SiO2 nanoparticles on outputs. Sustain. Mater. Technol. 2023, 37, e00668. [Google Scholar] [CrossRef]
  34. Makhesana, M.A.; Patel, K.M.; Krolczyk, G.M.; Danish, M.; Singla, A.K.; Khanna, N. Influence of MoS2 and graphite-reinforced nanofluid-MQL on surface roughness, tool wear, cutting temperature and microhardness in machining of Inconel 625. CIRP J. Manuf. Sci. Technol. 2023, 41, 225–238. [Google Scholar] [CrossRef]
  35. Ross, N.S.; Ganesh, M.; Srinivasan, D.; Gupta, M.K.; Korkmaz, M.E.; Krolczyk, J.B. Role of sustainable cooling/lubrication conditions in improving the tribological and machining characteristics of Monel-400 alloy. Tribol. Int. 2022, 176, 107880. [Google Scholar] [CrossRef]
  36. Xu, Y.; Zou, P.; He, Y.; Chen, S.; Tian, Y.; Gao, X. Comparative experimental research in turning of 304 austenitic stainless steel with and without ultrasonic vibration. Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci. 2016, 231, 2885–2901. [Google Scholar] [CrossRef]
  37. Jamil, M.; Khan, A.M.; Hegab, H.; Gong, L.; Mia, M.; Gupta, M.K.; He, N. Effects of hybrid Al2O3-CNT nanofluids and cryogenic cooling on machining of Ti–6Al–4V. Int. J. Adv. Manuf. Technol. 2019, 102, 3895–3909. [Google Scholar] [CrossRef]
  38. Sarıkaya, M.; Güllü, A. Taguchi design and response surface methodology based analysis of machining parameters in CNC turning under MQL. J. Clean. Prod. 2014, 65, 604–616. [Google Scholar] [CrossRef]
  39. Khalilpourazary, S.; Meshkat, S.S. Investigation of the effects of alumina nanoparticles on spur gear surface roughness and hob tool wear in hobbing process. Int. J. Adv. Manuf. Technol. 2014, 71, 1599–1610. [Google Scholar] [CrossRef]
  40. Hegab, H.; Kishawy, H.A.; Gadallah, M.H.; Umer, U.; Deiab, I. On machining of Ti-6Al-4V using multi-walled carbon nanotubes-based nano-fluid under minimum quantity lubrication. Int. J. Adv. Manuf. Technol. 2018, 97, 1593–1603. [Google Scholar] [CrossRef]
  41. Waikar, R.A.; Guo, Y.B. A comprehensive characterization of 3D surface topography induced by hard turning versus grinding. J. Mater. Process. Technol. 2008, 197, 189–199. [Google Scholar] [CrossRef]
  42. Usca, Ü.A.; Uzun, M.; Kuntoğlu, M.; Sap, E.; Gupta, M.K. Investigations on tool wear, surface roughness, cutting temperature, and chip formation in machining of Cu-B-CrC composites. Int. J. Adv. Manuf. Technol. 2021, 116, 3011–3025. [Google Scholar] [CrossRef]
  43. Thakur, D.G.; Ramamoorthy, B.; Vijayaraghavan, L. Study on the machinability characteristics of superalloy Inconel 718 during high speed turning. Mater. Des. 2009, 30, 1718–1725. [Google Scholar] [CrossRef]
  44. Şap, S.; Usca, Ü.A.; Uzun, M.; Kuntoğlu, M.; Salur, E. Performance evaluation of AlTiN coated carbide tools during machining of ceramic reinforced Cu-based hybrid composites under cryogenic, pure-minimum quantity lubrication and dry regimes. J. Compos. Mater. 2022, 56, 3401–3421. [Google Scholar] [CrossRef]
  45. Şap, E.; Usca, Ü.A.; Şap, S.; Polat, H.; Giasin, K.; Kalyoncu, M. Understanding the effects of machinability properties of Incoloy 800 superalloy under different machining conditions using artificial intelligence methods. Mater. Today Commun. 2024, 38, 108521. [Google Scholar] [CrossRef]
  46. Usca, Ü.A. The Effect of Cellulose Nanocrystal-Based Nanofluid on Milling Performance: An Investigation of Dillimax 690T. Polymers 2023, 15, 4521. [Google Scholar] [CrossRef] [PubMed]
  47. Demirpolat, H.; Binali, R.; Patange, A.D.; Pardeshi, S.S.; Gnanasekaran, S. Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel. Materials 2023, 16, 4408. [Google Scholar] [CrossRef] [PubMed]
  48. Şirin, E. Evaluation of tribological performance of MQL technique combined with LN2, CO2, N2 ecological cooling/lubrication techniques when turning of Hastelloy C22 superalloy. Tribol. Int. 2023, 188, 108786. [Google Scholar] [CrossRef]
  49. Binali, R.; Demirpolat, H.; Kuntoğlu, M.; Sağlam, H. Machinability Investigations Based on Tool Wear, Surface Roughness, Cutting Temperature, Chip Morphology and Material Removal Rate during Dry and MQL-Assisted Milling of Nimax Mold Steel. Lubricants 2023, 11, 101. [Google Scholar] [CrossRef]
  50. Ross, N.S.; Manasea Selvin, B.J.A.; Nagarajan, S.; Mashinini, P.M.; Dharmalingam, S.K.; Savio, A.P.; Gupta, M.K.; Korkmaz, M.E. Novel use of cryogenic cooling conditions in improving the machining performance of Al 8011/nano-SiC composites. Int. J. Adv. Manuf. Technol. 2023, 129, 1703–1715. [Google Scholar] [CrossRef]
  51. Usca, Ü.A.; Uzun, M.; Şap, S.; Kuntoğlu, M.; Giasin, K.; Pimenov, D.Y.; Wojciechowski, S. Tool wear, surface roughness, cutting temperature and chips morphology evaluation of Al/TiN coated carbide cutting tools in milling of Cu–B–CrC based ceramic matrix composites. J. Mater. Res. Technol. 2022, 16, 1243–1259. [Google Scholar] [CrossRef]
  52. Kaynak, Y. Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining. Int. J. Adv. Manuf. Technol. 2014, 72, 919–933. [Google Scholar] [CrossRef]
  53. Kshitij, G.; Khanna, N.; Yıldırım, Ç.V.; Dağlı, S.; Sarıkaya, M. Resource conservation and sustainable development in the metal cutting industry within the framework of the green economy concept: An overview and case study. Sustain. Mater. Technol. 2022, 34, e00507. [Google Scholar] [CrossRef]
  54. Usca, Ü.A.; Şap, S.; Uzun, M.; Kuntoğlu, M.; Salur, E.; Karabiber, A.; Pimenov, D.Y.; Giasin, K.; Wojciechowski, S. Estimation, Optimization and Analysis Based Investigation of the Energy Consumption in Machinability of Ceramic-Based Metal Matrix Composite Materials. J. Mater. Res. Technol. 2022, 17, 2987–2998. [Google Scholar] [CrossRef]
  55. Shah, P.; Bhat, P.; Khanna, N. Life cycle assessment of drilling Inconel 718 using cryogenic cutting fluids while considering sustainability parameters. Sustain. Energy Technol. Assess. 2021, 43, 100950. [Google Scholar] [CrossRef]
Machines 12 00436 g001
Figure 1. Experimental scheme.
Figure 1. Experimental scheme.
Machines 12 00436 g001
Machines 12 00436 g002
Figure 2. Nanofluid preparation process.
Figure 2. Nanofluid preparation process.
Machines 12 00436 g002
Machines 12 00436 g003
Figure 3. The diagram represents the wear mechanisms [36].
Figure 3. The diagram represents the wear mechanisms [36].
Machines 12 00436 g003
Machines 12 00436 g004
Figure 4. Effects of different cutting parameters and cutting environments on surface roughness (Ra).
Figure 4. Effects of different cutting parameters and cutting environments on surface roughness (Ra).
Machines 12 00436 g004
Machines 12 00436 g005
Figure 5. Surface topographies under various cutting conditions, including a Vc of 75 m/min and an fn of 0.075 mm/rev.
Figure 5. Surface topographies under various cutting conditions, including a Vc of 75 m/min and an fn of 0.075 mm/rev.
Machines 12 00436 g005
Machines 12 00436 g006
Figure 6. The impact of various cutting settings and cutting conditions on the development of Vb.
Figure 6. The impact of various cutting settings and cutting conditions on the development of Vb.
Machines 12 00436 g006
Machines 12 00436 g007
Figure 7. SEM pictures of cutting tools at 75 m/min Vc, 0.075 mm/rev fn, and different cutting environments.
Figure 7. SEM pictures of cutting tools at 75 m/min Vc, 0.075 mm/rev fn, and different cutting environments.
Machines 12 00436 g007
Machines 12 00436 g008
Figure 8. EDS analysis of cutting tools used in MQL environment.
Figure 8. EDS analysis of cutting tools used in MQL environment.
Machines 12 00436 g008
Machines 12 00436 g009
Figure 9. Cutting tool mapping analysis in dry environment.
Figure 9. Cutting tool mapping analysis in dry environment.
Machines 12 00436 g009
Machines 12 00436 g010
Figure 10. The influence of different cutting parameters and cutting circumstances on the temperature during cutting.
Figure 10. The influence of different cutting parameters and cutting circumstances on the temperature during cutting.
Machines 12 00436 g010
Machines 12 00436 g011
Figure 11. Thermal camera images taken during processing.
Figure 11. Thermal camera images taken during processing.
Machines 12 00436 g011
Machines 12 00436 g012
Figure 12. The influence of different cutting parameters and cutting circumstances on Pd.
Figure 12. The influence of different cutting parameters and cutting circumstances on Pd.
Machines 12 00436 g012
Table 1. Chemical composition of the test samples (AISI 5140) [19].
Table 1. Chemical composition of the test samples (AISI 5140) [19].
ElementsCSiMnPSCrFe
Range (%)0.450.30.750.0350.031Balance
Table 2. Comprehensive experimental design (2 × 2 × 4).
Table 2. Comprehensive experimental design (2 × 2 × 4).
Milling ParametersUnitLevels
L1L2L3L4
Cooling conditions-DryMQLFloodNanofluid
Cutting speed, (Vc)m/min75100--
Feed rate, (fn)mm/rev0.0750.100--
Table 3. Some properties of Mo nanopowders.
Table 3. Some properties of Mo nanopowders.
PropertiesValue
Bulk Density (g/cm3)0.25
True Density (g/cm3)10.2
Colorblack
Crystal Structurecubic
Mean Particle Diameter (nm)50
Specific Surface Area (m2/g)22.0–35.0
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Zerooğlu, T.; Değirmenci, Ü.; Şap, S. A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments. Machines 2024, 12, 436. https://doi.org/10.3390/machines12070436

AMA Style

Zerooğlu T, Değirmenci Ü, Şap S. A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments. Machines. 2024; 12(7):436. https://doi.org/10.3390/machines12070436

Chicago/Turabian Style

Zerooğlu, Tufan, Ünal Değirmenci, and Serhat Şap. 2024. "A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments" Machines 12, no. 7: 436. https://doi.org/10.3390/machines12070436

APA Style

Zerooğlu, T., Değirmenci, Ü., & Şap, S. (2024). A Study on the Machinability and Environmental Effects of Milling AISI 5140 Steel in Sustainable Cutting Environments. Machines, 12(7), 436. https://doi.org/10.3390/machines12070436

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop