Solids, Volume 5, Issue 1 (March 2024) – 11 articles

The modified suspension polymerization technique has been used for the preparation of composite microparticles from the mixture of glycidyl methacrylate (GMA), styrene (S), and divinylbenzene (DVB) in the presence of hydrophobized Fe₃O₄ nanoparticles. The obtained polymer microspheres were characterized using different instrumental and physicochemical techniques, modified with a zero-order PAMAM dendrimer, and impregnated with palladium(II) acetate solutions to immobilize palladium(II) ions. The resulting materials were preliminarily examined as catalysts in the Suzuki reaction between 4-bromotoluene and phenylboronic acid. It was found that the addition of magnetite particles to the composition of monomers provided polymer microparticles with embedded magnetic nanoparticles. The composite microparticles obtained showed a complex, multi-hollow, or raspberry-like morphology. After their modification, they could serve as recyclable catalysts for reactions that include both 4-bromotoluene and several other aryl bromides. Full article

Copper phosphides are promising materials for energy conversion applications because of their unique electronic structure and controllable composition. Two stoichiometric copper phosphides, CuP₂ and Cu₃P, were prepared by direct wet-chemical synthesis using red phosphorus. They were characterized by powder X-ray diffraction, scanning and transmission electron microscopy, and X-ray photoelectron spectroscopy. The precursor selection, reaction temperature, time and solvent composition were also studied. CuP₂ is the thermodynamically more stable product, but Cu₃P is more commonly obtained. This work demonstrated that higher temperature helps in CuP₂ formation. More importantly, using more trioctylphosphine oxide helps control the morphology leading to crystal growth along the crystallographic a-axis. CuP₂ and Cu₃P were tested for hydrogen evolution, oxygen evolution, and oxygen reduction reactions. CuP₂ works better for HER in acidic conditions and OER in general, and Cu₃P showed better activity than CuP₂ for HER and ORR in an alkaline medium. This study has led to a simple approach to the synthesis of CuP₂ nanowires. Full article

Compacted graphite iron (CGI) is an engineering material with the potential to fill the application gap between flake- and spheroidal-graphite irons thanks to its unique microstructure and competitive price. Despite its wide use and considerable past research, its complex microstructure often leads researchers to focus on models based on representative volume elements with multiple particles, frequently overlooking the impact of individual particle shapes and interactions between the neighbouring particles on crack initiation and propagation. This study focuses on the effects of graphite morphology and spacing between inclusions on the mechanical and fracture behaviours of CGI at the microscale. In this work, 2D cohesive-zone-element-based models with different graphite morphologies and spacings were developed to investigate the mechanical behaviour as well as crack initiation and propagation. ImageJ and scanning electron microscopy were used to characterise and analyse the microstructure of CGI. In simulations, both graphite particles and metallic matrix were assumed isotropic and ductile. Cohesive zone elements (CZEs) were employed in the whole domain studied. It was found that graphite morphology had a negligible effect on interface debonding but nodular inclusions can notably enhance the stiffness of the material and effectively impede the propagation of cracks within the matrix. Besides, a small distance between graphite particles accelerates the crack growth. These results can be used to design and manufacture better metal-matrix composites. Full article

The pressure-induced phase transformations of rare earth orthophosphates (REPO₄s) have become increasingly relevant in ceramic matrix composite (CMC) research; however, understanding of the shear-dependence of these transformations remains limited. This study employs diamond anvil cell experiments with three pressure media (neon, KCl, sample itself/no medium) to systematically assess the effect of shear on the phase transformations of TbPO₄. Results show a lowering of the TbPO₄ transformation onset pressure (P_onset) as well as an extension of the xenotime–monazite phase coexistence range under non-hydrostatic conditions. The TbPO₄ P_onset under no medium (4.4(3) GPa) is the lowest REPO₄ P_onset reported to date and represents a ~50% drop from the hydrostatic P_onset. Enthalpic differences likely account for lower P_onset values in TbPO₄ compared to DyPO₄. Experiments also show scheelite may be the post-monazite phase of TbPO₄; this phase is consistent with observed and predicted REPO₄ transformation pathways. Full article

The luminous transmittance and the color rendering index of daylight through semitransparent photovoltaic glazing are essential parameters for visual comfort indoors, and they must be considered for different absorber materials that were traditionally developed for opaque solar cells, such as those of the chalcopyrite type. With this aim, various chalcopyrite compounds (CuInSe₂, CuInS₂ and CuGaS₂) were prepared by means of evaporation and then measured to obtain their optical absorption spectra. These experimental data are used here to calculate the solar absorptance (α_S), luminous transmittance (τ_L) and color rendering index (R_a) as a function of the chalcopyrite film thickness. The comparative analysis of the different factors indicates that 70 nm thick CuInSe₂ is optimal to guarantee excellent visual comfort (τ_L = 50% and R_a = 93%) while absorbing as much solar irradiance (α_S = 37%) as 130 nm thick CuInS₂ or 900 nm thick CuGaS₂. The second option (130 nm thick CuInS₂) is also considered good (τ_L = 40% and R_a = 80%), but for CuGaS₂, the thickness should be kept below 250 nm in order to obtain a suitable color rendering R_a ≥ 60%. Full article

Two methods of durability prediction of fillet welds were researched in this study. Namely, the structural Hot-Spot method and the structural stress method fe-safe Verity were applied to fatigue life estimation of a double plate lap fillet weld made of high-strength complex phase CP-W800 steel. Durability predictions were compared against available high-cycle fatigue experimental data obtained for the same weld detail and material. Both 2D and 3D finite element meshes were considered in the simulations. It was shown that comparable predictions were obtained using either the Hot-Spot method or the fe-safe Verity module in the case of the 3D FE mesh. On the contrary, a less conservative durability prediction was observed using the Hot-Spot method and a more conservative durability prediction was gained using the fe-safe Verity module in the case of the 2D FE mesh due to a different consideration of stress concentration around the weld. Full article

Ceramic samples of Bi_1−xHo_xFeO₃, where x = 0.00–0.50, with a modifier concentration variation step ∆x = 0.05–0.10, were prepared by a two-step solid-phase synthesis followed by sintering using conventional ceramic technology. X-ray phase analysis showed that all the solid solutions studied were formed in the presence of impurities. With increasing Ho concentration, a non-monotonic shift in all loss maxima towards the low-frequency region is observed, as well as an increase in their half-width. An increase in the external temperature leads to a monotonic shift in the absorption maxima towards the low-frequency region, which enables the necessary control of the microwave parameters in the X band. A conclusion has been drawn on the feasibility of using the data obtained in the design of new functional materials based on BiFeO₃, as well as devices with thermally controlled frequency. Full article

Over the last few years, research activities have seen two-dimensional (2D) materials become protagonists in the field of nanotechnology. In particular, 2D materials characterized by ferroelectric properties are extremely interesting, as they are better suited for the development of miniaturized and high-performing devices. Here, we summarize the recent advances in this field, reviewing the realization of devices based on 2D ferroelectric materials, like FeFET, FTJ, and optoelectronics. The devices are realized with a wide range of material systems, from oxide materials at low dimensions to 2D materials exhibiting van der Waals interactions. We conclude by presenting how these materials could be useful in the field of devices based on magnons or surface acoustic waves. Full article

Photoluminescence (PL) from Be-doped bulk GaN crystals grown by the High Nitrogen Pressure Solution method was studied and compared with PL from GaN:Be layers on sapphire grown by molecular beam epitaxy and metalorganic chemical vapor deposition techniques. The yellow luminescence band in the latter is caused by the isolated Be_Ga acceptor (the YL_Be band), while the broad yellow band in bulk GaN:Be crystals is a superposition of the YL_Be band and another band, most likely the C_N-related YL1 band. The attribution of the yellow band in bulk GaN:Be crystals to the Be_GaO_N complex (a deep donor) is questioned. Full article

Based on a potential theoretical approach, the subsurface stress field is calculated for an elastic half-space which is subject to normal and uniaxial tangential surface tractions that—in the case of elastic decoupling—correspond to rigid normal and tangential translations of a circular surface domain. The stress fields are obtained explicitly and in closed form as the imaginary parts of compact complex-valued expressions. The stress state in the surface and on the central axis are considered in detail. As, within specific approximations that have been discussed at length in the literature, any tangential contact problem with friction can be understood as a certain incremental series of such rigid translations, the solutions presented here can serve as the basis of very fast superposition algorithms for the analysis of subsurface stress fields in general tangential contact problems with friction. This idea is demonstrated by means of the frictional tangential contact between an elastic half-space and a rigid cylindrical flat punch with rounded corners. Full article

Stearic and phenyl-phosphonic acids were applied to fine aluminum particles to understand their effect on the surface chemical composition and bulk properties of the surface-treated powders. During the solution phase deposition process, the surface composition changes chemically through a condensation reaction between the acid and particle surface hydroxyl groups, forming covalent chemical bonds. The retention of both types of acids was verified through characterization using Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The presence of stearic acid on the particle surface was observed through signature absorbance peaks, including interfacial C-O bonding modes, carboxylate, and carbonyl moieties, all present on both the treated powder. Spectra using XPS showed an increase in -CH relative intensity signal on the particle surface when compared to the raw material when considering the the carbon 2p photoelectron peak. Similar findings confirmed the presence of the phenyl-phosphonic acid when comparing to the raw material. The IR spectrum confirmed the presence of P-O-Al, P-O, and phosponates as a result of the surface bonding between the reagent and particles. XPS always provided evidence through the presence of phosphorous 2p and 2s photoelecton peaks at 191.3 and 133.4 eV, respectively. The bulk properties of both surface treated powders improved, as shown through improved apparent/tap density and a decreased Hausner Ratio (Group C to Group A behavior). Rheological characterization provided additional evidence by showing a reduced specific energy, flow rate index, and cohesion. The particle packing was improved as evidenced through reduced compressibility as a function of applied normal stress. Full article