Membranes

13 pages, 5902 KiB

Open AccessArticle

Effect of Loading and Functionalization of Carbon Nanotube on the Performance of Blended Polysulfone/Polyethersulfone Membrane during Treatment of Wastewater Containing Phenol and Benzene

by Mabusha S. Rameetse, Oluseyi Aberefa and Michael O. Daramola

Membranes 2020, 10(3), 54; https://doi.org/10.3390/membranes10030054 - 24 Mar 2020

Cited by 34 | Viewed by 3877

Abstract

In this study, a carbon nanotube (CNT)-infused blended polymer membrane was prepared and evaluated for phenol and benzene removal from petroleum industry wastewater. A 25:75 (by weight %) blended polysulfone/polyethersulfone (PSF/PES) membrane infused with CNTs was prepared and tested. The effect of functionalization [...] Read more.

In this study, a carbon nanotube (CNT)-infused blended polymer membrane was prepared and evaluated for phenol and benzene removal from petroleum industry wastewater. A 25:75 (by weight %) blended polysulfone/polyethersulfone (PSF/PES) membrane infused with CNTs was prepared and tested. The effect of functionalization of the CNTs on the quality and performance of the membrane was also investigated. The membranes were loaded with CNTs at different loadings: 0.5 wt. %, 1 wt. %, 1.5 wt. % pure CNTs (pCNTs) and 1 wt. % functionalized CNTs (fCNTs), to gain an insight into the effect of the amount of CNT on the quality and performance of the membranes. Physicochemical properties of the as-prepared membranes were obtained using scanning electron microscopy (SEM) for morphology, Raman spectroscopy for purity of the CNTs, Fourier transform infrared (FTIR) for surface chemistry, thermogravimetric analysis (TGA) for thermal stability, atomic force microscopy (AFM) for surface nature and nano-tensile analysis for the mechanical strength of the membranes. The performance of the membrane was tested with synthetic wastewater containing 20 ppm of phenol and 20 ppm of benzene using a dead-end filtration cell at a pressure ranging from 100 to 300 kPa. The results show that embedding CNTs in the blended polymer (PSF/PES) increased both the porosity and water absorption capacity of the membranes, thereby resulting in enhanced water flux up to 309 L/m²h for 1.5 wt. % pCNTs and 326 L/m²h for 1 wt. % functionalized CNT-loaded membrane. Infusing the polysulfone/polyethersulfone (PSF/PES) membrane with CNTs enhanced the thermal stability and mechanical strength. Results from AFM indicate enhanced hydrophilicity of the membranes, translating in the enhancement of anti-fouling properties of the membranes. However, the % rejection of membranes with CNTs decreased with an increase in pCNTs concentration and pressure, while it increased the membrane with fCNTs. The % rejection of benzene in the pCNTs membrane decreased with 13.5% and 7.55% in fCNT membrane while phenol decreased with 55.6% in pCNT membrane and 42.9% in the FCNT membrane. This can be attributed to poor CNT dispersion resulting in increased pore sizes observed when CNT concentration increases. Optimization of membrane synthesis might be required to enhance the separation performance of the membranes. Full article

(This article belongs to the Special Issue Point-of-use Membrane Technologies: Challenges and Opportunities)

► Show Figures

Graphical abstract

13 pages, 1987 KiB

Open AccessArticle

Exploring the Operation Factors that Influence Performance of a Spiral-Wound Forward Osmosis Membrane Process for Scale-up Design

by Sungyun Lee

Membranes 2020, 10(3), 53; https://doi.org/10.3390/membranes10030053 - 24 Mar 2020

Cited by 6 | Viewed by 3159

Abstract

Forward osmosis (FO) technology has increasingly attracted attention owing to its low operational energy and low fouling propensity. Despite extensive investigations on FO, very few module-scale FO studies on the operation and design of the FO process have been conducted. In this paper, [...] Read more.

Forward osmosis (FO) technology has increasingly attracted attention owing to its low operational energy and low fouling propensity. Despite extensive investigations on FO, very few module-scale FO studies on the operation and design of the FO process have been conducted. In this paper, a simple and practical FO process design parameter called normalized membrane area is suggested based on a performance analysis of spiral-wound FO elements. The influence of operation factors on operating pressures and water recovery was investigated using 8-inch spiral wound elements in the continuous operation mode. The membrane area was adjusted by series connection of FO elements to a maximum value of 46 m² (three elements). The feed and draw flow rates were varied between 5 and 15 LPM under various feed (10, 20, and 30 g/L) and draw (58.4 and 233.8 g/L) concentration combinations. The analysis of flow rates (feed, draw, and permeate flow rates) indicated not only high flow channel resistance on the draw side but also high permeate flow rates can induce higher operating pressures owing to strong mutual interaction of the feed and the draw streams. Feed water recovery was focused on as a key performance index, and the experimental recovery (R_Exp) and theoretical maximum recovery (R_Th) values were compared. The results revealed the significance of the feed flow rate and the membrane area in terms of enhancing the water recovery performance. In addition, a clear relationship was observed between the membrane area normalized by the initial feed flow rates and the water recovery ratio (R_Exp/R_Th), even though the applied operation conditions were different. Finally, an empirical equation to estimate the required membrane area of spiral-wound FO was proposed for the FO process design. The equation can be used to predict water recovery of FO systems as well, for example, if an FO system is operated at 0.08 m²L⁻¹h of the normalized membrane area, the system is expected to offer 78% of the R_Th value. Full article

(This article belongs to the Section Membrane Processing and Engineering)

► Show Figures

Graphical abstract

16 pages, 2349 KiB

Open AccessArticle

Effect of Chitosan’s Degree of Deacetylation on the Performance of PES Membrane Infused with Chitosan during AMD Treatment

by Machodi Mathaba and Michael Olawale Daramola

Membranes 2020, 10(3), 52; https://doi.org/10.3390/membranes10030052 - 24 Mar 2020

Cited by 46 | Viewed by 4364

Abstract

Acid mine drainage is an environmental problem associated with mining operations and activities. Its treatment is essential to achieving environmental sustainability. In this study, a polyethersulphone (PES) membrane infused with chitosan is proposed as a point-of-use material for treating acid mine drainage (AMD). [...] Read more.

Acid mine drainage is an environmental problem associated with mining operations and activities. Its treatment is essential to achieving environmental sustainability. In this study, a polyethersulphone (PES) membrane infused with chitosan is proposed as a point-of-use material for treating acid mine drainage (AMD). The composite material explored the synergetic effect between chitosan and polymer, particularly considering the effect of the degree of deacetylation (DD) of chitosan on the performance of membrane. Chitosan was produced from chitin under various synthesis process conditions and infused within polyethersulphone membrane. The results obtained show that chitosan with the highest degree of deacetylation was achieved with a temperature of 100 °C and NaOH concentration of 40 wt%. Increasing the temperature above 100 °C started degrading already formed or exposed amine groups, thus, reducing the DD of the chitosan sample. The contact angle and porosity analysis indicated that the hydrophilic nature of the membrane was enhanced with increasing DD of the chitosan. The performance of the membranes was conducted on a Dead-end filtration cell using synthetic acid mine drainage. The results showed that the flux and rejection of the membrane was enhanced with increasing degree of deacetylation. PES 5 and PES 1 were blended with chitosan having the highest (95.97%) and lowest (33.93%) degree of deacetylation, respectively. PES 5 reported pure water flux of 123 L/m²·h and PES 1 was recorded as 104 L/m²·h. Similarly, the rejection of the membrane was improved with increasing chitosan’s degree of deacetylation. PES 5 had higher rejection and PES 1 had the least rejection. Maximum rejection for the contaminants was determined as 98.05, 97.39, 96.25, 95.24 and 80.34% for Mn²⁺, Fe²⁺, Mg²⁺ and Ca²⁺ and SO₄²⁻, respectively. The results obtained show that chitosan’s degree of deacetylation has a positive effect on the performance of polyethersulphone membrane during the treatment of acid mine drainage. Full article

(This article belongs to the Special Issue Point-of-use Membrane Technologies: Challenges and Opportunities)

► Show Figures

Graphical abstract

15 pages, 2009 KiB

Open AccessEditor’s ChoiceArticle

Synthesis and Performance of Aromatic Polyamide Ionenes as Gas Separation Membranes

by Kathryn E. O’Harra, Irshad Kammakakam, Danielle M. Noll, Erika M. Turflinger, Grayson P. Dennis, Enrique M. Jackson and Jason E. Bara

Membranes 2020, 10(3), 51; https://doi.org/10.3390/membranes10030051 - 22 Mar 2020

Cited by 16 | Viewed by 4763

Abstract

Here, we report the synthesis and thermophysical properties of seven primarily aromatic, imidazolium-based polyamide ionenes. The effects of varied para-, meta-, and ortho-connectivity, and spacing of ionic and amide functional groups, on structural and thermophysical properties were analyzed. Suitable, robust [...] Read more.

Here, we report the synthesis and thermophysical properties of seven primarily aromatic, imidazolium-based polyamide ionenes. The effects of varied para-, meta-, and ortho-connectivity, and spacing of ionic and amide functional groups, on structural and thermophysical properties were analyzed. Suitable, robust derivatives were cast into thin films, neat, or with stoichiometric equivalents of the ionic liquid (IL) 1-benzy-3-methylimidazolium bistriflimide ([Bnmim][Tf₂N]), and the gas transport properties of these membranes were measured. Pure gas permeabilities and permselectivities for N₂, CH₄, and CO₂ are reported. Consistent para-connectivity in the backbone was shown to yield the highest CO₂ permeability and suitability for casting as a very thin, flexible film. Derivatives containing terephthalamide segments exhibited the highest CO₂/CH₄ and CO₂/N₂ selectivities, yet CO₂ permeability decreased with further deviation from consistent para-linkages. Full article

(This article belongs to the Special Issue Ionic Liquid-based Materials for Membrane Processes)

► Show Figures

Graphical abstract

21 pages, 11140 KiB

Open AccessArticle

Synthesis of Silica Membranes by Chemical Vapor Deposition Using a Dimethyldimethoxysilane Precursor

by S. Ted Oyama, Haruki Aono, Atsushi Takagaki, Takashi Sugawara and Ryuji Kikuchi

Membranes 2020, 10(3), 50; https://doi.org/10.3390/membranes10030050 - 22 Mar 2020

Cited by 12 | Viewed by 4241

Abstract

Silica-based membranes prepared by chemical vapor deposition of tetraethylorthosilicate (TEOS) on γ-alumina overlayers are known to be effective for hydrogen separation and are attractive for membrane reactor applications for hydrogen-producing reactions. In this study, the synthesis of the membranes was improved by simplifying [...] Read more.

Silica-based membranes prepared by chemical vapor deposition of tetraethylorthosilicate (TEOS) on γ-alumina overlayers are known to be effective for hydrogen separation and are attractive for membrane reactor applications for hydrogen-producing reactions. In this study, the synthesis of the membranes was improved by simplifying the deposition of the intermediate γ-alumina layers and by using the precursor, dimethyldimethoxysilane (DMDMOS). In the placement of the γ-alumina layers, earlier work in our laboratory employed four to five dipping-calcining cycles of boehmite sol precursors to produce high H₂ selectivities, but this took considerable time. In the present study, only two cycles were needed, even for a macro-porous support, through the use of finer boehmite precursor particle sizes. Using the simplified fabrication process, silica-alumina composite membranes with H₂ permeance > 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ and H₂/N₂ selectivity >100 were successfully synthesized. In addition, the use of the silica precursor, DMDMOS, further improved the H₂ permeance without compromising the H₂/N₂ selectivity. Pure DMDMOS membranes proved to be unstable against hydrothermal conditions, but the addition of aluminum tri-sec-butoxide (ATSB) improved the stability just like for conventional TEOS membranes. Full article

(This article belongs to the Special Issue Membranes: 10th Anniversary)

► Show Figures

Graphical abstract

19 pages, 7016 KiB

Open AccessEditor’s ChoiceArticle

Potentiodynamic and Galvanodynamic Regimes of Mass Transfer in Flow-Through Electrodialysis Membrane Systems: Numerical Simulation of Electroconvection and Current-Voltage Curve

by Aminat Uzdenova and Makhamet Urtenov

Membranes 2020, 10(3), 49; https://doi.org/10.3390/membranes10030049 - 20 Mar 2020

Cited by 12 | Viewed by 3546

Abstract

Electromembrane devices are usually operated in two electrical regimes: potentiodynamic (PD), when a potential drop in the system is set, and galvanodynamic (GD), when the current density is set. This article theoretically investigates the current-voltage curves (CVCs) of flow-through electrodialysis membrane systems calculated [...] Read more.

Electromembrane devices are usually operated in two electrical regimes: potentiodynamic (PD), when a potential drop in the system is set, and galvanodynamic (GD), when the current density is set. This article theoretically investigates the current-voltage curves (CVCs) of flow-through electrodialysis membrane systems calculated in the PD and GD regimes and compares the parameters of the electroconvective vortex layer for these regimes. The study is based on numerical modelling using a basic model of overlimiting transfer enhanced by electroconvection with a modification of the boundary conditions. The Dankwerts’ boundary condition is used for the ion concentration at the inlet boundary of the membrane channel. The Dankwerts’ condition allows one to increase the accuracy of the numerical implementation of the boundary condition at the channel inlet. On the CVCs calculated for PD and DG regimes, four main current modes can be distinguished: underlimiting, limiting, overlimiting, and chaotic overlimiting. The effect of the electric field regime is manifested in overlimiting current modes, when a significant electroconvection vortex layer develops in the channel. Full article

(This article belongs to the Special Issue Electromembrane Processes: Experiments and Modelling)

► Show Figures

Graphical abstract

31 pages, 5084 KiB

Open AccessArticle

Morphology of Thin Film Composite Membranes Explored by Small-Angle Neutron Scattering and Positron-Annihilation Lifetime Spectroscopy

by Vitaliy Pipich, Marcel Dickmann, Henrich Frielinghaus, Roni Kasher, Christoph Hugenschmidt, Winfried Petry, Yoram Oren and Dietmar Schwahn

Membranes 2020, 10(3), 48; https://doi.org/10.3390/membranes10030048 - 18 Mar 2020

Cited by 14 | Viewed by 4957

Abstract

The morphology of thin film composite (TFC) membranes used in reverse osmosis (RO) and nanofiltration (NF) water treatment was explored with small-angle neutron scattering (SANS) and positron-annihilation lifetime spectroscopy (PALS). The combination of both methods allowed the characterization of the bulk porous structure [...] Read more.

The morphology of thin film composite (TFC) membranes used in reverse osmosis (RO) and nanofiltration (NF) water treatment was explored with small-angle neutron scattering (SANS) and positron-annihilation lifetime spectroscopy (PALS). The combination of both methods allowed the characterization of the bulk porous structure from a few Å to µm in radius. PALS shows pores of ~4.5 Å average radius in a surface layer of about 4 μm thickness, which become ~40% smaller at the free surface of the membranes. This observation may correlate with the glass state of the involved polymer. Pores of similar size appear in SANS as closely packed pores of ~6 Å radius distributed with an average distance of ~30 Å. The main effort of SANS was the characterization of the morphology of the porous polysulfone support layer as well as the fibers of the nonwoven fabric layer. Contrast variation using the media H₂O/D₂O and supercritical CO₂ and CD₄ identified the polymers of the support layers as well as internal heterogeneities. Full article

(This article belongs to the Section Inorganic Membranes)

► Show Figures

Graphical abstract

17 pages, 3156 KiB

Open AccessEditor’s ChoiceArticle

Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

by Maryam Y. Ghadhban, Hasan Shaker Majdi, Khalid T. Rashid, Qusay F. Alsalhy, D. Shanthana Lakshmi, Issam K. Salih and Alberto Figoli

Membranes 2020, 10(3), 47; https://doi.org/10.3390/membranes10030047 - 18 Mar 2020

Cited by 40 | Viewed by 5389

Abstract

In this work, a flat-sheet blend membrane was fabricated by a traditional phase inversion method, using the polymer blends poly phenyl sulfone (PPSU) and polyether sulfone (PES) for the ultrafiltration (UF) application. It was hypothesized that adding PES to the PPSU polymer blend [...] Read more.

In this work, a flat-sheet blend membrane was fabricated by a traditional phase inversion method, using the polymer blends poly phenyl sulfone (PPSU) and polyether sulfone (PES) for the ultrafiltration (UF) application. It was hypothesized that adding PES to the PPSU polymer blend would improve the properties of the PPSU membrane. The effect of the PES concentration on the blend membrane properties was investigated extensively. The characteristics of PPSU-PES blend membranes were investigated using atomic force microscopy (AFM), scanning electron microscopy (SEM), contact angle measure, and contaminant (dye) elimination efficiency. This study showed that PES clearly affected the structural formation of the blended membranes. A considerable increase in the average roughness (about 93%) was observed with the addition of 4% PES, with a higher mean pore size accompanied by a rise in the pores’ density on the surface of the membrane. The addition of up to 4% PES had a significant influence on the hydrophilic character of the PPSU-PES membrane, by lowering the value of the contact angle (CA) (i.e., to 56.9°). The performance of the PPSU-PES composite membranes’ UF performance was systematically investigated, and the membrane pure water permeability (PWP) was enhanced by 25% with the addition of 4% PES. The best separation removal factor achieved in the current investigation for dye (Drupel Black NT) was 96.62% for a PPSU-PES (16:4 wt./wt.%) membrane with a 50% feed dye concentration. Full article

(This article belongs to the Special Issue Membrane Preparation and Characterisation and Their Application in Environmental Field (Volume II))

► Show Figures

Graphical abstract

18 pages, 3385 KiB

Open AccessArticle

Influence of Anion Structure on Thermal, Mechanical and CO₂ Solubility Properties of UV-Cross-Linked Poly(ethylene glycol) Diacrylate Iongels

by Ana P. S. Martins, Asier Fdz De Añastro, Jorge L. Olmedo-Martínez, Ana R. Nabais, Luísa A. Neves, David Mecerreyes and Liliana C. Tomé

Membranes 2020, 10(3), 46; https://doi.org/10.3390/membranes10030046 - 17 Mar 2020

Cited by 13 | Viewed by 4667

Abstract

Iongel-based CO₂ separation membranes were prepared by fast (< 1 min) UV-initiated polymerization of poly(ethylene glycol) diacrylate (PEGDA) in the presence of different ionic liquids (ILs) with the [C₂mim]⁺ cation and anions such as [TFSI]⁻, [FSI]⁻ [...] Read more.

Iongel-based CO₂ separation membranes were prepared by fast (< 1 min) UV-initiated polymerization of poly(ethylene glycol) diacrylate (PEGDA) in the presence of different ionic liquids (ILs) with the [C₂mim]⁺ cation and anions such as [TFSI]⁻, [FSI]⁻, [C(CN)₃]⁻ and [B(CN)₄]⁻. The four ILs were completely miscible with the non-ionic PEGDA network. Transparent and free-standing iongels containing between 60 and 90 %wt of IL were obtained and characterized by diverse techniques (FTIR, TGA, DSC, DMTA, SEM, CO₂ solubility and pure gas permeability). The thermal and mechanical stability of the iongels, as well as CO₂ solubility, were found to be strictly dependent on the IL content and the anion’s nature. The TGA results indicated that the iongels mostly follow the thermal profile of the respective neat ILs. The DMTA analysis revealed that the iongels based on fluorinated anions have higher storage modulus than those of cyano-functionalized anions. Conversely, the PEGDA–C(CN)₃ iongels presented the highest CO₂ solubility values ranging from 72 to 80 mmol/g. Single CO₂ permeabilities of 583 ± 29 Barrer and ideal CO₂/N₂ selectivities of 66 ± 3 were obtained with the PEGDA–70 C(CN)₃ iongel membrane. This work demonstrates that the combination of PEGDA with high contents of the best performing ILs is a promising and simple strategy, opening up new possibilities in the design of high-performance iongel membranes for CO₂ separation. Full article

(This article belongs to the Special Issue Ionic Liquid-based Materials for Membrane Processes)

► Show Figures

Graphical abstract

14 pages, 3129 KiB

Open AccessArticle

The Use of Succinonitrile as an Electrolyte Additive for Composite-Fiber Membranes in Lithium-Ion Batteries

by Jahaziel Villarreal, Roberto Orrostieta Chavez, Sujay A. Chopade, Timothy P. Lodge and Mataz Alcoutlabi

Membranes 2020, 10(3), 45; https://doi.org/10.3390/membranes10030045 - 17 Mar 2020

Cited by 7 | Viewed by 5699

Abstract

In the present work, the effect of temperature and additives on the ionic conductivity of mixed organic/ionic liquid electrolytes (MOILEs) was investigated by conducting galvanostatic charge/discharge and ionic conductivity experiments. The mixed electrolyte is based on the ionic liquid (IL) (EMI/TFSI/LiTFSI) and organic [...] Read more.

In the present work, the effect of temperature and additives on the ionic conductivity of mixed organic/ionic liquid electrolytes (MOILEs) was investigated by conducting galvanostatic charge/discharge and ionic conductivity experiments. The mixed electrolyte is based on the ionic liquid (IL) (EMI/TFSI/LiTFSI) and organic solvents EC/DMC (1:1 v/v). The effect of electrolyte type on the electrochemical performance of a LiCoO₂ cathode and a SnO₂/C composite anode in lithium anode (or cathode) half-cells was also investigated. The results demonstrated that the addition of 5 wt.% succinonitrile (SN) resulted in enhanced ionic conductivity of a 60% EMI-TFSI 40% EC/DMC MOILE from ~14 mS·cm⁻¹ to ~26 mS·cm⁻¹ at room temperature. Additionally, at a temperature of 100 °C, an increase in ionic conductivity from ~38 to ~69 mS·cm⁻¹ was observed for the MOILE with 5 wt% SN. The improvement in the ionic conductivity is attributed to the high polarity of SN and its ability to dissolve various types of salts such as LiTFSI. The galvanostatic charge/discharge results showed that the LiCoO₂ cathode with the MOILE (without SN) exhibited a 39% specific capacity loss at the 50th cycle while the LiCoO₂ cathode in the MOILE with 5 wt.% SN showed a decrease in specific capacity of only 14%. The addition of 5 wt.% SN to the MOILE with a SnO₂/C composite-fiber anode resulted in improved cycling performance and rate capability of the SnO₂/C composite-membrane anode in lithium anode half-cells. Based on the results reported in this work, a new avenue and promising outcome for the future use of MOILEs with SN in lithium-ion batteries (LIBs) can be opened. Full article

(This article belongs to the Special Issue Composite Electrolyte & Electrode Membranes for Electrochemical Energy Storage & Conversion Devices)

► Show Figures

Graphical abstract

20 pages, 3536 KiB

Open AccessArticle

Valorization of Fish by-Products: Purification of Bioactive Peptides from Codfish Blood and Sardine Cooking Wastewaters by Membrane Processing

by Soudabeh Ghalamara, Sara Silva, Carla Brazinha and Manuela Pintado

Membranes 2020, 10(3), 44; https://doi.org/10.3390/membranes10030044 - 13 Mar 2020

Cited by 29 | Viewed by 4990

Abstract

Codfish blood and sardine cooking wastewaters were processed using membrane ultrafiltration that allowed for the preparation of bioactive peptides enriched fractions. The raw materials and corresponding permeates were characterized chemically and in terms of biological properties. The fractionation process was evaluated by analyzing [...] Read more.

Codfish blood and sardine cooking wastewaters were processed using membrane ultrafiltration that allowed for the preparation of bioactive peptides enriched fractions. The raw materials and corresponding permeates were characterized chemically and in terms of biological properties. The fractionation process was evaluated by analyzing the selective permeation of small peptides (<1 kDa) from larger compounds when using membranes with different molecular weight cut-offs (MWCOs) combined with different materials (MW, PW, and UP010 for codfish blood) and when operated at different transmembrane pressures (with GH for sardine cooking wastewaters). A rejection of the protein/peptides >10 kDa was achieved for both raw materials with the studied membranes. Also, low values of rejection of peptides <1 kDa were accomplished, namely 2% with UP010 from codfish blood and 23% when operated at minimum pressure (1.0 bar) with GH from sardine wastewaters. The peptide fractions from codfish blood with MW and UP010 exhibited the highest ABTS⁺ and ORAC values. Peptide fractions from sardine wastewaters with GH demonstrated no improvement in antioxidant activity compared to sardine wastewaters. The antimicrobial results showed that the peptide fractions from codfish blood with UP010 and from sardine with GH at 1.0 bar were capable of inhibiting Escherichia coli growth. Full article

(This article belongs to the Special Issue Membrane Processes and Materials for a Sustainable Bioeconomy)

► Show Figures

Graphical abstract

11 pages, 5026 KiB

Open AccessArticle

Effects of Seed Crystals on the Growth and Catalytic Performance of TS-1 Zeolite Membranes

by Wenjuan Ding, Sitong Xiang, Fei Ye, Tian Gui, Yuqin Li, Fei Zhang, Na Hu, Meihua Zhu and Xiangshu Chen

Membranes 2020, 10(3), 41; https://doi.org/10.3390/membranes10030041 - 13 Mar 2020

Cited by 7 | Viewed by 3078

Abstract

Dense and good catalytic performance TS-1 zeolite membranes were rapidly prepared on porous mullite support by secondary hydrothermal synthesis. The properties of seed crystals were very important for the preparation of high-catalytic performance TS-1 zeolite membranes. Influences of seed crystals (Ti/Si ratios, size, [...] Read more.

Dense and good catalytic performance TS-1 zeolite membranes were rapidly prepared on porous mullite support by secondary hydrothermal synthesis. The properties of seed crystals were very important for the preparation of high-catalytic performance TS-1 zeolite membranes. Influences of seed crystals (Ti/Si ratios, size, morphology, and zeolites concentration of the seed suspension) on the growth and catalytic property of TS-1 zeolite membranes were investigated in details. High Ti/Si ratio, medium-size, and morphology of the seed crystals were critical for preparing the high-performance TS-1 zeolite membrane. Compared with the bi-layer TS-1 zeolite membrane (inner and outer of the mullite tube), the mono-layer TS-1 zeolite membrane had a better catalytic performance for Isopropanol IPA oxidation with H₂O₂. When the Ti/Si ratio, size, and morphology of the TS-1 zeolites were 0.030, 300 nm, ellipsoid, and the zeolites concentration of the seed suspension was 5%, the IPA conversion, and flux through the TS-1 zeolite membrane were 98.23% and 2.58 kg·m⁻²·h⁻¹, respectively. Full article

(This article belongs to the Section Inorganic Membranes)

► Show Figures

Graphical abstract

13 pages, 6597 KiB

Open AccessArticle

Measurement of Multi Ion Transport through Human Bronchial Epithelial Cell Line Provides an Insight into the Mechanism of Defective Water Transport in Cystic Fibrosis

by Miroslaw Zajac, Andrzej Lewenstam, Piotr Bednarczyk and Krzysztof Dolowy

Membranes 2020, 10(3), 43; https://doi.org/10.3390/membranes10030043 - 12 Mar 2020

Cited by 9 | Viewed by 4411

Abstract

We measured concentration changes of sodium, potassium, chloride ions, pH and the transepithelial potential difference by means of ion-selective electrodes, which were placed on both sides of a human bronchial epithelial 16HBE14σ cell line grown on a porous support in the presence of [...] Read more.

We measured concentration changes of sodium, potassium, chloride ions, pH and the transepithelial potential difference by means of ion-selective electrodes, which were placed on both sides of a human bronchial epithelial 16HBE14σ cell line grown on a porous support in the presence of ion channel blockers. We found that, in the isosmotic transepithelial concentration gradient of either sodium or chloride ions, there is an electroneutral transport of the isosmotic solution of sodium chloride in both directions across the cell monolayer. The transepithelial potential difference is below 3 mV. Potassium and pH change plays a minor role in ion transport. Based on our measurements, we hypothesize that in a healthy bronchial epithelium, there is a dynamic balance between water absorption and secretion. Water absorption is caused by the action of two exchangers, Na/H and Cl/HCO₃, secreting weakly dissociated carbonic acid in exchange for well dissociated NaCl and water. The water secretion phase is triggered by an apical low volume-dependent factor opening the Cystic Fibrosis Transmembrane Regulator CFTR channel and secreting anions that are accompanied by paracellular sodium and water transport. Full article

(This article belongs to the Special Issue Advances in Artificial and Biological Membranes: Mechanisms of Ionic Sensitivity, Ion-Sensor Designs and Applications for Ions Measurement)

► Show Figures

Graphical abstract

19 pages, 3392 KiB

Open AccessArticle

Using Additives for Fouling Control in a Lab-Scale MBR; Comparing the Anti-Fouling Potential of Coagulants, PAC and Bio-Film Carriers

by Petros Gkotsis, Anastasios Zouboulis and Manassis Mitrakas

Membranes 2020, 10(3), 42; https://doi.org/10.3390/membranes10030042 - 12 Mar 2020

Cited by 10 | Viewed by 3107

Abstract

This study investigates the effect of different additives, such as coagulants/flocculants, adsorption agents (powdered activated carbon, PAC), and bio-film carriers, on the fouling propensity of a lab-scale membrane bio-reactor (MBR) treating synthetic municipal wastewater. The coagulation agents FO 4350 SSH, Adifloc KD 451, [...] Read more.

This study investigates the effect of different additives, such as coagulants/flocculants, adsorption agents (powdered activated carbon, PAC), and bio-film carriers, on the fouling propensity of a lab-scale membrane bio-reactor (MBR) treating synthetic municipal wastewater. The coagulation agents FO 4350 SSH, Adifloc KD 451, and PAC1 A9-M at concentrations of 10 mg/L, 10 mg/L, and 100 mg Al/L, respectively, and PAC at a concentration of 3.6 ± 0.1 g/L, exhibited the best results during their batch-mode addition to biomass samples. The optimal additives FO 4350 SSH and Adifloc KD 451 were continuously added to the bioreactor at continuous-flow addition experiments and resulted in increased membrane lifetime by 16% and 13%, respectively, suggesting that the decrease of SMP_c concentration and the increase of sludge filterability is the dominant fouling reduction mechanism. On the contrary, fouling reduction was low when PAC1 A9-M and PAC were continuously added, as the membrane lifetime was increased by approximately 6%. Interestingly, the addition of bio-film carriers (at filling ratios of 40%, 50%, and 60%) did not affect SMP_c concentration, sludge filterability, and trans-membrane pressure (TMP). Finally, the effluent quality was satisfactory in terms of organics and ammonia removal, as chemical oxygen demand (COD), biochemical oxygen demand (BOD)₅, and NH

_{4}^{+}

-N concentrations were consistently below the permissible discharge limits and rarely exceeded 30, 15, and 0.9 mg/L, respectively. Full article

(This article belongs to the Special Issue New Perspectives on Membrane Bioreactors)

► Show Figures

Graphical abstract

16 pages, 5864 KiB

Open AccessArticle

Effect of Surface Inhomogeneity of Ion-Exchange Membranes on the Mass Transfer Efficiency in Pulsed Electric Field Modes

by Dmitrii Butylskii, Ilya Moroz, Kseniya Tsygurina and Semyon Mareev

Membranes 2020, 10(3), 40; https://doi.org/10.3390/membranes10030040 - 11 Mar 2020

Cited by 18 | Viewed by 3207

Abstract

Despite the growing interest in pulsed electric field modes in membrane separation processes, there are currently not many works devoted to studying the effect of the surface properties and composition of ion-exchange membranes on their efficiency in these modes. In this paper, we [...] Read more.

Despite the growing interest in pulsed electric field modes in membrane separation processes, there are currently not many works devoted to studying the effect of the surface properties and composition of ion-exchange membranes on their efficiency in these modes. In this paper, we have shown the effect of increasing mass transfer using different kinds of ion-exchange membranes (heterogeneous and homogeneous with smooth, undulated, and rough surfaces) during electrodialysis in the pulsed electric field modes at underlimiting and overlimiting currents. It was found that the maximum increment in the average current is achieved when the average potential corresponds to the right-hand edge of the limiting current plateau of the voltammetric curve, i.e., at the maximum resistance of the system in the DC mode. For the first time, the development of electroconvective vortices was visualized in pulsed electric field modes and it was experimentally shown that even at relatively low frequencies, a non-uniform concentration field is preserved at the time of a pause, which stimulates the rapid development of electroconvection when pulses are switched on again. In the case of relatively high pulse frequencies, the electroconvective vortices formed during a pulse lapse do not completely decay during a pause; they only slightly decrease in size. Full article

(This article belongs to the Special Issue Membranes: 10th Anniversary)

► Show Figures

Graphical abstract

15 pages, 3136 KiB

Open AccessArticle

Electrospun Weak Anion-Exchange Fibrous Membranes for Protein Purification

by Shu-Ting Chen, S. Ranil Wickramasinghe and Xianghong Qian

Membranes 2020, 10(3), 39; https://doi.org/10.3390/membranes10030039 - 1 Mar 2020

Cited by 15 | Viewed by 3959

Abstract

Membrane based ion-exchange (IEX) and hydrophobic interaction chromatography (HIC) for protein purification is often used to remove impurities and aggregates operated under the flow-through mode. IEX and HIC are also limited by capacity and recovery when operated under bind-and-elute mode for the fractionation [...] Read more.

Membrane based ion-exchange (IEX) and hydrophobic interaction chromatography (HIC) for protein purification is often used to remove impurities and aggregates operated under the flow-through mode. IEX and HIC are also limited by capacity and recovery when operated under bind-and-elute mode for the fractionation of proteins. Electrospun nanofibrous membrane is characterized by its high surface area to volume ratio and high permeability. Here tertiary amine ligands are grafted onto the electrospun polysulfone (PSf) and polyacrylonitrile (PAN) membrane substrates using UV-initiated polymerization. Static and dynamic binding capacities for model protein bovine serum albumin (BSA) were determined under appropriate bind and elute buffer conditions. Static and dynamic binding capacities in the order of ~100 mg/mL were obtained for the functionalized electrospun PAN membranes whereas these values reached ~200 mg/mL for the functionalized electrospun PSf membranes. Protein recovery of over 96% was obtained for PAN-based membranes. However, it is only 56% for PSf-based membranes. Our work indicates that surface modification of electrospun membranes by grafting polymeric ligands can enhance protein adsorption due to increased surface area-to-volume ratio. Full article

(This article belongs to the Special Issue Membrane Chromatography for Biomolecules Purification)

► Show Figures

Figure 1

13 pages, 3167 KiB

Open AccessArticle

Effects of Room Temperature Stretching and Annealing on the Crystallization Behavior and Performance of Polyvinylidene Fluoride Hollow Fiber Membranes

by Yuanhui Tang, Yakai Lin, Hanhan Lin, Chunyu Li, Bo Zhou and Xiaolin Wang

Membranes 2020, 10(3), 38; https://doi.org/10.3390/membranes10030038 - 29 Feb 2020

Cited by 11 | Viewed by 3639

Abstract

A treatment consisting of room temperature stretching and subsequent annealing was utilized to regulate the morphology and performance of polyvinylidene fluoride (PVDF) hollow fiber membranes. The effects of stretching ratios and stretching rates on the crystallization behavior, morphology, and performance of the PVDF [...] Read more.

A treatment consisting of room temperature stretching and subsequent annealing was utilized to regulate the morphology and performance of polyvinylidene fluoride (PVDF) hollow fiber membranes. The effects of stretching ratios and stretching rates on the crystallization behavior, morphology, and performance of the PVDF membranes were investigated. The results showed that the treatment resulted in generation of the β crystalline phase PVDF and increased the crystallinity of the membrane materials. The treatment also brought about the orientation of the membrane pores along the stretching direction and led to an increase in the mean pore size of the membranes. In addition, as the stretching ratio increased, the tensile strength and permeation flux were improved while the elongation at break was depressed. However, compared to the stretching ratio, the stretching rate had less influence on the membrane structure and performance. In general, as the stretching ratio was 50% and the stretching rate was 20 mm/min, the tensile strength was increased by 36% to 7.47 MPa, and the pure water flux was as high as 776.28 L/(m²·h·0.1bar), while the mean pore size was not changed significantly. This research proved that the room temperature stretching and subsequent annealing was a simple but effective method for regulating the structure and the performance of the PVDF porous membranes. Full article

(This article belongs to the Section Membrane Analysis and Characterization)

► Show Figures

Graphical abstract

17 pages, 3554 KiB

Open AccessArticle

Exclusion of Estrogenic and Androgenic Steroid Hormones from Municipal Membrane Bioreactor Wastewater Using UF/NF/RO Membranes for Water Reuse Application

by Mujahid Aziz and Tunde Ojumu

Membranes 2020, 10(3), 37; https://doi.org/10.3390/membranes10030037 - 27 Feb 2020

Cited by 35 | Viewed by 5365

Abstract

In the context of water scarcity, domestic secondary effluent reuse may be an option as a reliable source for alleviating acute water shortage. The increasing risks linked with the presence of natural steroid hormones and many emerging anthropogenic micropollutants (MPs) passing through municipal [...] Read more.

In the context of water scarcity, domestic secondary effluent reuse may be an option as a reliable source for alleviating acute water shortage. The increasing risks linked with the presence of natural steroid hormones and many emerging anthropogenic micropollutants (MPs) passing through municipal wastewater treatment works (MWWTWs) are of concern for their endocrine-disrupting activities. In this study, domestic wastewater treated by a full-scale membrane bioreactor (MBR) at an MWWTW in the Western Cape Province, South Africa, was used directly as the influent to a reverse osmosis (RO) pilot plant for the removal of selected natural steroid hormones 17β-estradiol (E₂) and testosterone (T) as a potential indirect water recycling application. Estrogenicity and androgenicity were assessed using the enzyme-linked immunosorbent assays (ELISA) and the recombinant yeast estrogen receptor binding assays (YES). The influent pH and flux did not influence the rejection of E₂ and T, which was most likely due to adsorption, size exclusion, and diffusion simultaneously. RO and nanofiltration (NF) exhibited excellent removal rates (>95%) for E₂ and T. All the E₂ effluent samples with MBR/ultrafiltration (UF), MBR/NF, and MBR/RO were lower than the US EPA and WHO trigger value of 0.7 ng/L, as well as the predicted no-effect concentration (PNEC) values for fish (1 ng E₂/L). Full article

(This article belongs to the Special Issue Advances in Reverse Osmosis Membranes and Processes)

► Show Figures

Graphical abstract

17 pages, 3999 KiB

Open AccessEditor’s ChoiceArticle

Innovative Poly (Vinylidene Fluoride) (PVDF) Electrospun Nanofiber Membrane Preparation Using DMSO as a Low Toxicity Solvent

by Francesca Russo, Claudia Ursino, Elisa Avruscio, Giovanni Desiderio, Andrea Perrone, Sergio Santoro, Francesco Galiano and Alberto Figoli

Membranes 2020, 10(3), 36; https://doi.org/10.3390/membranes10030036 - 26 Feb 2020

Cited by 62 | Viewed by 8639

Abstract

Electrospinning is an emerging technique for the preparation of electrospun fiber membranes (ENMs), and a very promising one on the basis of the high-yield and the scalability of the process according to a process intensification strategy. Most of the research reported in the [...] Read more.

Electrospinning is an emerging technique for the preparation of electrospun fiber membranes (ENMs), and a very promising one on the basis of the high-yield and the scalability of the process according to a process intensification strategy. Most of the research reported in the literature has been focused on the preparation of poly (vinylidene fluoride) (PVDF) ENMs by using N,N- dimethylformamide (DMF) as a solvent, which is considered a mutagenic and cancerogenic substance. Hence, the possibility of using alternative solvents represents an interesting approach to investigate. In this work, we explored the use of dimethyl sulfoxide (DMSO) as a low toxicity solvent in a mixture with acetone for the preparation of PVDF-ENMs. As a first step, a solubility study of the polymer, PVDF 6012 Solef^®, in several DMSO/acetone mixtures was carried out, and then, different operating conditions (e.g., applied voltage and needle to collector plate distance) for the successful electrospinning of the ENMs were evaluated. The study provided evidence of the crucial role of solution conductivity in the electrospinning phase and the thermal post-treatment. The prepared ENMs were characterized by evaluating the morphology (by SEM), pore-size, porosity, surface properties, and performance in terms of water permeability. The obtained results showed the possibility of producing ENMs in a more sustainable way, with a pore size in the range of 0.2–0.8 µm, high porosity (above 80%), and water flux in the range of 11.000–38.000 L/m²·h·bar. Full article

(This article belongs to the Special Issue Membrane Processes and Materials for a Sustainable Bioeconomy)

► Show Figures

Figure 1

18 pages, 4544 KiB

Open AccessArticle

Evaluating the Feasibility of Forward Osmosis in Diluting RO Concentrate Using Pretreatment Backwash Water

by Susanthi Liyanaarachchi, Veeriah Jegatheesan, Li Shu, Ho Kyong Shon, Shobha Muthukumaran and Chun Qing Li

Membranes 2020, 10(3), 35; https://doi.org/10.3390/membranes10030035 - 25 Feb 2020

Cited by 5 | Viewed by 3806

Abstract

Forward osmosis (FO) is an excellent membrane process to dilute seawater (SW) reverse osmosis (RO) concentrate for either to increase the water recovery or for safe disposal. However, the low fluxes through FO membranes as well the biofouling/scaling of FO membranes are bottlenecks [...] Read more.

Forward osmosis (FO) is an excellent membrane process to dilute seawater (SW) reverse osmosis (RO) concentrate for either to increase the water recovery or for safe disposal. However, the low fluxes through FO membranes as well the biofouling/scaling of FO membranes are bottlenecks of this process requiring larger membrane area and membranes with anti-fouling properties. This study evaluates the performance of hollow fibre and flat sheet membranes with respect to flux and biofouling. Ferric hydroxide sludge was used as impaired water mimicking the backwash water of a filter that is generally employed as pretreatment in a SWRO plant and RO concentrate was used as draw solution for the studies. Synthetic salts are also used as draw solutions to compare the flux produced. The study found that cellulose triacetate (CTA) flat sheet FO membrane produced higher flux (3–6 L m⁻² h⁻¹) compared to that produced by polyamide (PA) hollow fibre FO membrane (less than 2.5 L m⁻² h⁻¹) under the same experimental conditions. Therefore, long-term studies conducted on the flat sheet FO membranes showed that fouling due to ferric hydroxide sludge did not allow the water flux to increase more than 3.15 L m⁻² h⁻¹. Full article

(This article belongs to the Special Issue CESE-2019: Applications of Membranes for Sustainability)

► Show Figures

Figure 1

21 pages, 4884 KiB

Open AccessEditor’s ChoiceReview

Performance of Polymer Electrolyte Membrane for Direct Methanol Fuel Cell Application: Perspective on Morphological Structure

by Hazlina Junoh, Juhana Jaafar, Nik Abdul Hadi Md Nordin, Ahmad Fauzi Ismail, Mohd Hafiz Dzarfan Othman, Mukhlis A. Rahman, Farhana Aziz and Norhaniza Yusof

Membranes 2020, 10(3), 34; https://doi.org/10.3390/membranes10030034 - 25 Feb 2020

Cited by 47 | Viewed by 9143

Abstract

Membrane morphology plays a great role in determining the performance of polymer electrolyte membranes (PEMs), especially for direct methanol fuel cell (DMFC) applications. Membrane morphology can be divided into two types, which are dense and porous structures. Membrane fabrication methods have different configurations, [...] Read more.

Membrane morphology plays a great role in determining the performance of polymer electrolyte membranes (PEMs), especially for direct methanol fuel cell (DMFC) applications. Membrane morphology can be divided into two types, which are dense and porous structures. Membrane fabrication methods have different configurations, including dense, thin and thick, layered, sandwiched and pore-filling membranes. All these types of membranes possess the same densely packed structural morphology, which limits the transportation of protons, even at a low methanol crossover. This paper summarizes our work on the development of PEMs with various structures and architecture that can affect the membrane’s performance, in terms of microstructures and morphologies, for potential applications in DMFCs. An understanding of the transport behavior of protons and methanol within the pores’ limits could give some perspective in the delivery of new porous electrolyte membranes for DMFC applications. Full article

(This article belongs to the Special Issue Mass Transfer in Membranes)

► Show Figures

Graphical abstract

Journal Menu

Journal Browser

Membranes, Volume 10, Issue 3 (March 2020) – 21 articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI