sensors-logo

Journal Browser

Journal Browser

Quantum Sensors and Sensing Technology

A special issue of Sensors (ISSN 1424-8220). This special issue belongs to the section "Optical Sensors".

Deadline for manuscript submissions: 20 March 2025 | Viewed by 8602

Special Issue Editor


E-Mail Website
Guest Editor
Istituto Nazionale di Ricerca Metrologica, Strada delle Cacce 91, 10135 Turin, Italy
Interests: quantum sensing; NV centers; optical-detected magnetic resonance; quantum thermodynamics; bio-sensing

Special Issue Information

Dear Colleagues,

Quantum sensing is based on taking advantage of quantum features to increase the sensitivity of the measurement of a physical quantity. The quantum features exploited are usually quantum superposition, entanglement, and quantum correlations. The physical quantities measured are electric and magnetic field, temperature, and pressure. In addition, imaging resolution can be enhanced by taking advantage of quantum correlations.

Quantum sensing has rapidly developed in the last few years in the broader context of emerging quantum technologies. Quantum effects, such as entanglement, move from being only theoretical or reserved, to specific challenging experiments intended to be the base of recent technological improvements.

This Special Issue aims to gather research and review articles on recent advances, technologies, solutions, applications, and new challenges in the field of quantum sensing.

Potential topics include, but are not limited to:

  • Quantum sensing with photons.
  • Quantum sensing with nitrogen-vacancy centers.
  • Quantum sensing with flux quits.
  • Quantum sensing with trapped ions.
  • Portable sensors.

Dr. Ettore Bernardi
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Sensors is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • lab-on-a-chip
  • quantum superposition
  • entanglement
  • quantum correlation
  • Heisenberg limit
  • sub-shot noise

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (7 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

16 pages, 7725 KiB  
Article
Investigating Nanoscale Interactions of Host–Guest Complexes Formed Between CB[7] and Atenolol by Quantum Chemistry and Ultrasensitive Vibrational Spectroscopy
by Anca Onaciu, Valentin Toma, Rareș-Mario Borșa, Vasile Chiș, Gabriela-Fabiola Știufiuc, Carina Culic, Constantin-Mihai Lucaciu and Rareș-Ionuț Știufiuc
Sensors 2024, 24(22), 7156; https://doi.org/10.3390/s24227156 - 7 Nov 2024
Viewed by 519
Abstract
In addition to the course of over 20 years of cucurbit-7-uril (CB[7]) in the pharmaceutical industry, the present study brings together the most recent observations from the perspective of ultrasensitive Raman spectroscopy and Density Functional Theory (DFT) related to the interaction of this [...] Read more.
In addition to the course of over 20 years of cucurbit-7-uril (CB[7]) in the pharmaceutical industry, the present study brings together the most recent observations from the perspective of ultrasensitive Raman spectroscopy and Density Functional Theory (DFT) related to the interaction of this molecule with atenolol (Ate) enantiomers during the formation of these host–guest complexes. Quantum chemistry calculations based on DFT were first used to understand the interaction geometry between CB[7] and Ate. These results were further confirmed by ultrasensitive vibrational spectroscopy. The spectral features associated with each enantiomer in the presence of CB[7] were analyzed by means of SERS, highlighting distinct interaction profiles. These experimental findings validated quantum chemical calculations, offering a comprehensive understanding of the host–guest interactions at the nanoscale level. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

18 pages, 20932 KiB  
Article
Microcontroller-Optimized Measurement Electronics for Coherent Control Applications of NV Centers
by Dennis Stiegekötter, Jens Pogorzelski, Ludwig Horsthemke, Frederik Hoffmann, Markus Gregor and Peter Glösekötter
Sensors 2024, 24(10), 3138; https://doi.org/10.3390/s24103138 - 15 May 2024
Viewed by 1218
Abstract
Long coherence times at room temperature make the NV center a promising candidate for quantum sensors and quantum computers. The necessary coherent control of the electron spin triplet in the ground state requires microwave π pulses in the nanosecond range, obtained from the [...] Read more.
Long coherence times at room temperature make the NV center a promising candidate for quantum sensors and quantum computers. The necessary coherent control of the electron spin triplet in the ground state requires microwave π pulses in the nanosecond range, obtained from the Rabi oscillation of the mS spin states of the magnetic resonances of the NV centers. Laboratory equipment has a high temporal resolution for these measurements but is expensive and, therefore, uninteresting for fields such as education. In this work, we present measurement electronics for NV centers that are optimized for microcontrollers. It is shown that the Rabi frequency is linear to the output of the digital-to-analog converter (DAC) and is used to adapt the time length π of the electron spin flip, to the limited pulse width resolution of the microcontroller. This was achieved by breaking down the most relevant functions of conventional laboratory devices and replacing them with commercially available integrated components. The result is a cost-effective handheld setup for coherent control applications of NV centers. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

13 pages, 5145 KiB  
Article
Excited-State Lifetime of NV Centers for All-Optical Magnetic Field Sensing
by Ludwig Horsthemke, Jens Pogorzelski, Dennis Stiegekötter, Frederik Hoffmann, Lutz Langguth, Robert Staacke, Christian Laube, Wolfgang Knolle, Markus Gregor and Peter Glösekötter
Sensors 2024, 24(7), 2093; https://doi.org/10.3390/s24072093 - 25 Mar 2024
Cited by 1 | Viewed by 1922
Abstract
We investigate the magnetic field-dependent fluorescence lifetime of microdiamond powder containing a high density of nitrogen-vacancy centers. This constitutes a non-intensity quantity for robust, all-optical magnetic field sensing. We propose a fiber-based setup in which the excitation intensity is modulated in a frequency [...] Read more.
We investigate the magnetic field-dependent fluorescence lifetime of microdiamond powder containing a high density of nitrogen-vacancy centers. This constitutes a non-intensity quantity for robust, all-optical magnetic field sensing. We propose a fiber-based setup in which the excitation intensity is modulated in a frequency range up to 100MHz. The change in magnitude and phase of the fluorescence relative to B=0 is recorded where the phase shows a maximum in magnetic contrast of 5.8 at 13MHz. A lock-in amplifier-based setup utilizing the change in phase at this frequency shows a 100 times higher immunity to fluctuations in the optical path compared to the intensity-based approach. A noise floor of 20μT/Hz and a shot-noise-limited sensitivity of 0.95μT/Hz were determined. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

11 pages, 1755 KiB  
Article
Limitations of Bulk Diamond Sensors for Single-Cell Thermometry
by Andrea Alessio, Ettore Bernardi, Ekaterina Moreva, Ivo Pietro Degiovanni, Marco Genovese and Marco Truccato
Sensors 2024, 24(1), 200; https://doi.org/10.3390/s24010200 - 29 Dec 2023
Viewed by 1251
Abstract
The present paper reports on a Finite Element Method (FEM) analysis of the experimental situation corresponding to the measurement of the temperature variation in a single cell plated on bulk diamond by means of optical techniques. Starting from previous experimental results, we have [...] Read more.
The present paper reports on a Finite Element Method (FEM) analysis of the experimental situation corresponding to the measurement of the temperature variation in a single cell plated on bulk diamond by means of optical techniques. Starting from previous experimental results, we have determined—in a uniform power density approximation and under steady-state conditions—the total heat power that has to be dissipated by a single cell plated on a glassy substrate in order to induce the typical maximum temperature increase ΔTglass=1 K. While keeping all of the other parameters constant, the glassy substrate has been replaced by a diamond plate. The FEM analysis shows that, in this case, the maximum temperature increase is expected at the diamond/cell interface and is as small as ΔTdiam=4.6×104 K. We have also calculated the typical decay time in the transient scenario, which resulted in τ 250 μs. By comparing these results with the state-of-the-art sensitivity values, we prove that the potential advantages of a longer coherence time, better spectral properties, and the use of special field alignments do not justify the use of diamond substrates in their bulk form. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

8 pages, 751 KiB  
Communication
Attosecond-Level Delay Sensing via Temporal Quantum Erasing
by Fabrizio Sgobba, Andrea Andrisani, Stefano Dello Russo, Mario Siciliani de Cumis and Luigi Santamaria Amato
Sensors 2023, 23(18), 7758; https://doi.org/10.3390/s23187758 - 8 Sep 2023
Cited by 3 | Viewed by 928
Abstract
Traditional Hong-Ou-Mandel (HOM) interferometry, insensitive to photons phase mismatch, proved to be a rugged single-photon interferometric technique. By introducing a post-beam splitter polarization-dependent delay, it is possible to recover phase-sensitive fringes, obtaining a temporal quantum eraser that maintains the ruggedness of the original [...] Read more.
Traditional Hong-Ou-Mandel (HOM) interferometry, insensitive to photons phase mismatch, proved to be a rugged single-photon interferometric technique. By introducing a post-beam splitter polarization-dependent delay, it is possible to recover phase-sensitive fringes, obtaining a temporal quantum eraser that maintains the ruggedness of the original HOM with enhanced sensitivity. This setup shows promising applications in biological sensing and optical metrology, where high sensitivity requirements are coupled with the necessity to keep light intensity as low as possible to avoid power-induced degradation. In this paper, we developed a highly sensitive single photon birefringence-induced delay sensor operating in the telecom range (1550 nm). By using a temporal quantum eraser based on common path Hongr-Ou-Mandel Interferometry, we were able to achieve a sensitivity of 4 as for an integration time of 2·104 s. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

9 pages, 545 KiB  
Communication
Microwave Electrometry with Multi-Photon Coherence in Rydberg Atoms
by Zheng Yin, Qianzhu Li, Xiaoyun Song, Zhengmao Jia, Michal Parniak, Xiao Lu and Yandong Peng
Sensors 2023, 23(16), 7269; https://doi.org/10.3390/s23167269 - 19 Aug 2023
Viewed by 1350
Abstract
A scheme for the measurement of a microwave (MW) electric field is proposed via multi-photon coherence in Rydberg atoms. It is based on the three-photon electromagnetically induced absorption (TPEIA) spectrum. In this process, the multi-photon produces a narrow absorption peak, which has a [...] Read more.
A scheme for the measurement of a microwave (MW) electric field is proposed via multi-photon coherence in Rydberg atoms. It is based on the three-photon electromagnetically induced absorption (TPEIA) spectrum. In this process, the multi-photon produces a narrow absorption peak, which has a larger magnitude than the electromagnetically induced transparency (EIT) peak under the same conditions. The TPEIA peak is sensitive to MW fields, and can be used to measure MW electric field strength. We found that the magnitude of TPEIA peaks shows a linear relationship with the MW field strength. The simulation results show that the minimum detectable strength of the MW fields is about 1/10 of that based on an common EIT effect, and the probe sensitivity could be improved by about four times. Furthermore, the MW sensing based on three-photon coherence seems to be robust against the changes in the control field and shows a broad tunability, and the scheme may be useful for designing novel MW sensing devices. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

12 pages, 1183 KiB  
Article
Experimental Guesswork with Quantum Side Information Using Twisted Light
by Vishal Katariya, Narayan Bhusal and Chenglong You
Sensors 2023, 23(14), 6570; https://doi.org/10.3390/s23146570 - 21 Jul 2023
Cited by 1 | Viewed by 792
Abstract
Guesswork is an information–theoretic quantity which can be seen as an alternate security criterion to entropy. Recent work has established the theoretical framework for guesswork in the presence of quantum side information, which we extend both theoretically and experimentally. We consider guesswork when [...] Read more.
Guesswork is an information–theoretic quantity which can be seen as an alternate security criterion to entropy. Recent work has established the theoretical framework for guesswork in the presence of quantum side information, which we extend both theoretically and experimentally. We consider guesswork when the side information consists of the BB84 states and their higher-dimensional generalizations. With this side information, we compute the guesswork for two different scenarios for each dimension. We then performed a proof-of-principle experiment using Laguerre–Gauss modes to experimentally compute the guesswork for higher-dimensional generalizations of the BB84 states. We find that our experimental results agree closely with our theoretical predictions. This work shows that guesswork can be a viable security criterion in cryptographic tasks and is experimentally accessible in a number of optical setups. Full article
(This article belongs to the Special Issue Quantum Sensors and Sensing Technology)
Show Figures

Figure 1

Back to TopTop