Aerospace

23 pages, 2008 KiB

Open AccessArticle

Adaptive Robust Time-Varying Formation Control of Quadrotors under Switching Topologies: Theory and Experiment

by Ziqian Zhao, Ming Zhu and Jiazheng Qin

Aerospace 2023, 10(8), 735; https://doi.org/10.3390/aerospace10080735 - 21 Aug 2023

Viewed by 1350

This paper investigates a practical time-varying formation control method for quadrotors subjected to disturbances, uncertainties, and switching-directed topologies. A fully distributed formation control scheme is proposed using a linear-velocity independent position controller (LVIPC) and a nonsingular terminal sliding mode attitude controller (NTSMAC). A [...] Read more.

This paper investigates a practical time-varying formation control method for quadrotors subjected to disturbances, uncertainties, and switching-directed topologies. A fully distributed formation control scheme is proposed using a linear-velocity independent position controller (LVIPC) and a nonsingular terminal sliding mode attitude controller (NTSMAC). A distributed observer is adopted to eliminate the measurement of linear-velocity states, and only local neighbor states are needed to realize formation flight. A time-varying nonsingular terminal sliding mode manifold is designed to suppress the reaching phase and ensure the finite-time convergence. Adaptive estimators are employed to remove the reliance on the prior knowledge of the upper bound of lumped uncertainties. It is then proven that all the closed-loop signals are bounded under the proposed method. Comparative experimental results based on a practical outdoor hardware solution are presented to confirm the effectiveness of the suggested control algorithm. Full article

► Show Figures

Figure 1

18 pages, 7192 KiB

Open AccessArticle

Efficient Global Aerodynamic Shape Optimization of a Full Aircraft Configuration Considering Trimming

by Kai Wang, Zhonghua Han, Keshi Zhang and Wenping Song

Aerospace 2023, 10(8), 734; https://doi.org/10.3390/aerospace10080734 - 21 Aug 2023

Cited by 4 | Viewed by 2116

Abstract

Most existing aerodynamic shape optimization (ASO) studies do not take the balanced pitching moment into account and thus the optimized configuration has to be trimmed to ensure zero pitching moment, which causes additional drag and reduces the benefit of ASO remarkably. This article [...] Read more.

Most existing aerodynamic shape optimization (ASO) studies do not take the balanced pitching moment into account and thus the optimized configuration has to be trimmed to ensure zero pitching moment, which causes additional drag and reduces the benefit of ASO remarkably. This article proposes an efficient global ASO method that directly enforces a zero pitching moment constraint. A free-form deformation (FFD) parameterization combing Laplacian smoothing method is implemented to parameterize a full aircraft configuration and ensure sufficiently smooth aerodynamic shapes. Reynolds-averaged Navier–Stokes (RANS) equations are solved to simulate transonic viscous flows. A surrogate-based multi-round optimization strategy is used to drive ASO towards the global optimum. To verify the effectiveness of the proposed method, we adopt two design optimization strategies for the NASA Common Research Model (CRM) wing–body–tail configuration. The first strategy is to optimize the configuration without considering balance of pitching moment, and then manually trim the optimized configuration by deflecting the horizontal tail. The second one is to directly enforce the zero pitching moment constraint in the optimization model and take the deflection angle of the horizontal tail as an additional design variable. Results show that: (1) for the first strategy, about 4-count drag-reducing benefits would be lost when manually trimming the optimal configuration; (2) the second strategy can achieve 3.2-count more drag-reducing benefits than the first strategy; (3) compared with gradient-based optimization (GBO), surrogate-based optimization (SBO) is more efficient than GBO for ASO problems with around 80 design variables, and the benefit of ASO achieved by SBO is comparable to that obtained by GBO. Full article

(This article belongs to the Special Issue Aerodynamic and Multidisciplinary Design Optimization)

► Show Figures

Figure 1

10 pages, 3954 KiB

Open AccessArticle

A Comparison of the Damage Tolerance of AA7075-T6, AA2024-T3, and Boeing Space, Intelligence, and Weapons Systems AM-Built LPBF Scalmalloy

by Rhys Jones, Daren Peng, Andrew Ang, Richard W. Aston, Nicole D. Schoenborn and Nam D. Phan

Aerospace 2023, 10(8), 733; https://doi.org/10.3390/aerospace10080733 - 20 Aug 2023

Cited by 2 | Viewed by 3409

Abstract

This paper first presents the results of an experimental study into the damage tolerance of AA7075-T6, which is widely used in both fixed- and rotary-wing aircraft, space structures, and laser bed powder fusion (LBPF) Scalmalloy specimens built by Boeing Space, Intelligence, and Weapons [...] Read more.

This paper first presents the results of an experimental study into the damage tolerance of AA7075-T6, which is widely used in both fixed- and rotary-wing aircraft, space structures, and laser bed powder fusion (LBPF) Scalmalloy specimens built by Boeing Space, Intelligence, and Weapons Systems. To this end, four single edge notch AA7075-T6 specimens and four identical single edge notch LBPF Scalmalloy specimens were tested. The resultant crack growth curves reveal that Boeing Space, Intelligence, and Weapons Systems AM-built Scalmalloy is more damage tolerant than conventionally built AA7075-T6. This finding leads to the observation that the da/dN versus ΔK curves associated with Scalmalloy and conventionally manufactured AA2024-T3 are similar. These findings highlight the potential for Boeing Space, Intelligence, and Weapons Systems AM-built Scalmalloy to be used to extend the operational lives of military aircraft by the on-demand printing of limited-life Scalmalloy replacement parts. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

22 pages, 8443 KiB

Open AccessArticle

Effect of Combustor Outlet Geometry on Operating Characteristics of Disk-Shaped Rotating Detonation Engine

by Zhenjuan Xia, Hu Ma, Gaoyang Ge, Yong He and Changsheng Zhou

Aerospace 2023, 10(8), 732; https://doi.org/10.3390/aerospace10080732 - 20 Aug 2023

Viewed by 1587

Abstract

A disk-shaped rotating detonation engine with H₂/air mixture was tested to identify the impact of combustor outlet geometry on the engine’s operating characteristics. Three combustor outlet diameters and five outlet lengths are employed in the experiments. Results show that with the [...] Read more.

A disk-shaped rotating detonation engine with H₂/air mixture was tested to identify the impact of combustor outlet geometry on the engine’s operating characteristics. Three combustor outlet diameters and five outlet lengths are employed in the experiments. Results show that with the increase of combustor convergent ratio, the propagation stability of the rotating detonation wave decreases, and the propagation velocity and pressure peak decrease slightly. When the convergent ratio increases to a certain value (1.70 in this study), a “platform zone” with a lower pressure value appears before the sharp rise of the dynamic pressure curve. The propagation mode varies with the increase of mass flow rate at different convergent ratios. As the mass flow rate increases, the wave head number in the combustor increases. But the change rule of propagation mode with mass flow rate is greatly affected by convergent ratio. Increasing the convergent ratio is conducive to the formation of multi-wave modes, and the critical mass flow rate for mode transition drops sharply. When the convergent ratio increases to 1.70, the unstable asymmetric dual-wave mode is obtained. With the increase in the convergent ratio, the engine’s operating range and operating stability decrease significantly. Finally, changing the combustor outlet length has little influence on the engine’s operating characteristics and detonation-wave parameters. Full article

(This article belongs to the Special Issue Advances in Detonative Propulsion)

► Show Figures

Figure 1

24 pages, 1876 KiB

Open AccessArticle

The Influence of Repair Quality on Aircraft Spare Part Demand Variability

by Lars M. Heijenrath and Wim J. C. Verhagen

Aerospace 2023, 10(8), 731; https://doi.org/10.3390/aerospace10080731 - 20 Aug 2023

Cited by 1 | Viewed by 1916

Abstract

Accurate estimation of spare part demand is challenging in the case of intermittent or lumpy demand, characterised by infrequent demand occurrence and variability in demand size. While prior research has considered the effect of exogenous variables on spare part demand, there is a [...] Read more.

Accurate estimation of spare part demand is challenging in the case of intermittent or lumpy demand, characterised by infrequent demand occurrence and variability in demand size. While prior research has considered the effect of exogenous variables on spare part demand, there is a lack of research considering the effects of repair quality and aggregated spare part demand behaviour across fleets of assets under the influence of multiple simultaneously acting drivers of failure. This research provides new insights towards the problem of estimating variable spare part demand through modelling and simulation of the effects of multiple, simultaneously considered spare part demand drivers. In particular, a contribution to the state of the art is introduced by the use of a Branching Poisson Process (BPP) to model repair quality effects for spare part demand generation in conjunction with several demand drivers. The approach is applied in a numerical study which involves component failure characteristics based on real-life data from an aircraft maintenance, repair and overhaul (MRO) provider. It is shown that repair quality improvements drive down the variance in the demand and the total number of failures over time, and outperform the effect of environmental drivers of failure in terms of demand generation. Full article

(This article belongs to the Special Issue Selected Papers from the 4th International Aviation Management Conference)

► Show Figures

Figure 1

13 pages, 2586 KiB

Open AccessArticle

Optimization Research on the Heat Transfer Capacity of an Aircraft Fuel Thermal Management System

by Qidong Zhang, Guiping Lin, Jinghui Guo, Haichuan Jin and Qiming Zhang

Aerospace 2023, 10(8), 730; https://doi.org/10.3390/aerospace10080730 - 20 Aug 2023

Cited by 2 | Viewed by 2126

Abstract

The thermal management system (TMS) for aircraft fuel is a critical component of integrated TMSs in aircraft. As such, its optimal design is necessary to ensure the efficient completion of flight missions. This study presents the model building of a numerical simulation model [...] Read more.

The thermal management system (TMS) for aircraft fuel is a critical component of integrated TMSs in aircraft. As such, its optimal design is necessary to ensure the efficient completion of flight missions. This study presents the model building of a numerical simulation model for the fuel TMS, with the objective of minimizing fuel return flow. Sensitivity analysis was performed using variance analysis. The genetic algorithm was utilized for the optimization of the model building, taking into consideration the system’s geometric structure and performance parameters, which include the pipe length, the ram air-fuel HX’s efficiency, and the ram air’s volume flow rate in the ram air cooling subsystem, as design variables. The optimization solution for system design variables yielded a design scheme with the highest working efficiency for the fuel TMS. In this paper, the genetic algorithm in AMEsim software is adopted, which can also effectively optimize the design parameters and achieve the optimization objective. Compared with the original TMS structure, the heat dissipation capacity of the fuel TMS is improved and reduced the return fuel flow by 67.4% after the optimization of system structure parameters. Full article

► Show Figures

Figure 1

26 pages, 12223 KiB

Open AccessArticle

Control of Cowl Shock/Boundary Layer Interaction in Supersonic Inlet Based on Dynamic Vortex Generator

by Mengge Wang, Ziyun Wang, Yue Zhang, Daishu Cheng, Huijun Tan, Kun Wang and Simin Gao

Aerospace 2023, 10(8), 729; https://doi.org/10.3390/aerospace10080729 - 20 Aug 2023

Cited by 4 | Viewed by 1843

Abstract

A shock wave/boundary layer interaction (SWBLI) is a common phenomenon in supersonic inlet flow, which can significantly degrade the aerodynamic performance of the inlet by inducing boundary layer separation. To address this issue, in this paper, we propose the use of a dynamic [...] Read more.

A shock wave/boundary layer interaction (SWBLI) is a common phenomenon in supersonic inlet flow, which can significantly degrade the aerodynamic performance of the inlet by inducing boundary layer separation. To address this issue, in this paper, we propose the use of a dynamic vortex generator to control the SWBLI in a typical supersonic inlet. The unsteady simulation method based on dynamic grid technology was employed to verify the effectiveness of the proposed method of control and investigate its mechanism. The results showed that, in a duct of finite width at the inlet, the SWBLI generated complex three-dimensional (3D) flow structures with remarkable swirling properties. At the same time, vortex pairs were generated close to the side wall as a result of its presence, and this led to the intensification of transverse flow and, in turn, the formation of a complex 3D structure of the flow of the separation bubble. The dynamic vortex generator induced oscillations of variable intensity in the vortex system in the supersonic boundary layer that enhanced the mixing between the boundary layer flow and the mainstream. Meanwhile, the unique effects of “extrusion” and “suction” in the oscillation process continued to charge the airflow, and the distribution of velocity in the boundary layer significantly improved. As the oscillation frequency of the vortex generator increased, its charging effect on low-velocity flow in the boundary layer increased, and its control effect on the flow field of the SWBLI became more pronounced. The proposed method of control reduced the length of the separation bubble by 31.76% and increased the total pressure recovery coefficient at the inlet by 6.4% compared to the values in the absence of control. Full article

(This article belongs to the Special Issue Shock-Dominated Flow)

► Show Figures

Figure 1

17 pages, 4491 KiB

Open AccessArticle

A Dynamic Cross-Collaborative Interception Algorithm Based on GTSMC and Virtual Geometry

by Kang Niu, Xu Bai, Xi Chen, Jianqiao Yu and Haiying Liu

Aerospace 2023, 10(8), 728; https://doi.org/10.3390/aerospace10080728 - 20 Aug 2023

Viewed by 1319

Abstract

In the model (m:n), to improve the autonomous collaborative interception capability for air vehicle, a new autonomous cross-collaborative interception algorithm based on GTSMC (Global Terminal Sliding Mode Control) and real-time virtual geometry is proposed in this paper. Firstly, the conception of an autonomous [...] Read more.

In the model (m:n), to improve the autonomous collaborative interception capability for air vehicle, a new autonomous cross-collaborative interception algorithm based on GTSMC (Global Terminal Sliding Mode Control) and real-time virtual geometry is proposed in this paper. Firstly, the conception of an autonomous cross-collaboration is defined and the multi-air vehicle for the multi- object interception problem is formulated. Then, this paper presents the dynamic situation assessment function, which considers the real-time flight status and cooperative status of the air vehicle during the interception of the object. At the same time, this paper states the condition of whether the air vehicle is in a cooperative state and proves it. After completing the dynamic situation assessment, and considering the dynamic of the air vehicles, a new controller is designed by using GTSMC and the idea of backstepping method. Simultaneously, this paper gives a stability analysis of the closed-loop system by using Lyapunov theory. Finally, to demonstrate the effectiveness of the proposed algorithm, several simulation cases which consider different interception scenarios are given. The simulation results show that the new collaborative interception algorithm can provide better autonomous cross-collaborative interception capability and higher accuracy. Full article

► Show Figures

Figure 1

19 pages, 8908 KiB

Open AccessArticle

Testing of the N₂O/HDPE Vortex Flow Pancake Hybrid Rocket Engine with Augmented Spark Igniter

by Tomasz Palacz and Jacek Cieślik

Aerospace 2023, 10(8), 727; https://doi.org/10.3390/aerospace10080727 - 20 Aug 2023

Viewed by 3274

Abstract

The paper is part of the research aimed at determining if the vortex flow pancake (VFP) hybrid rocket engine is feasible as green in-space chemical propulsion. The objective of this study is to test an N₂O/HDPE VFP hybrid ignited with N [...] Read more.

The paper is part of the research aimed at determining if the vortex flow pancake (VFP) hybrid rocket engine is feasible as green in-space chemical propulsion. The objective of this study is to test an N₂O/HDPE VFP hybrid ignited with N₂O/C₃H₈ torch igniter. The N₂O is used in self-pressurizing mode, which results in two-phase flow and varying inlet conditions, thus better simulating real in-space behavior. The study begins with characterizing the torch igniter, followed by hot-fire ignition tests of the VFP. The results allow for the improved design of the torch igniter and VFP hybrid. The axial regression rate ballistic coefficients are reported for the N₂O/HDPE propellants in the VFP configuration. Full article

(This article belongs to the Special Issue Green Propulsion: Present Solutions and Perspectives for Powering Environmentally Friendly Space Missions)

► Show Figures

Figure 1

28 pages, 4735 KiB

Open AccessArticle

Aero-Engine Preliminary Design Optimization and Operability Studies Supported by a Compressor Mean-Line Design Module

by Alexios Alexiou, Ioannis Kolias, Nikolaos Aretakis and Konstantinos Mathioudakis

Aerospace 2023, 10(8), 726; https://doi.org/10.3390/aerospace10080726 - 20 Aug 2023

Viewed by 3056

Abstract

An approach for preliminary aero-engine design, incorporating a mean-line code for the design of axial-flow, multi-stage compressors, is presented. The compressor mean-line code is developed and integrated within a framework for the preliminary design and assessment of aero-engine concepts. It is then combined [...] Read more.

An approach for preliminary aero-engine design, incorporating a mean-line code for the design of axial-flow, multi-stage compressors, is presented. The compressor mean-line code is developed and integrated within a framework for the preliminary design and assessment of aero-engine concepts. It is then combined with modules for compressor map generation, multi-point engine design, steady-state and transient engine off-design performance and aircraft mission analysis. Implementation examples are presented, demonstrating the determination of the optimal combination of compressor and engine design parameters for achieving minimum fuel burn over a specific aircraft mission, while obeying constraints that guarantee operability over the entire flight envelope. Constraints related to compressor stability during transient maneuvers between idle and static take-off conditions and engine temperature limits at maximum take-off are respected by the final design. The results demonstrate the potential for design trade-offs between engine performance at the aircraft mission level and compressor aerodynamic stability. Full article

(This article belongs to the Special Issue Aerodynamic and Multidisciplinary Design Optimization)

► Show Figures

Figure 1

20 pages, 6693 KiB

Open AccessArticle

Study on the Forced Torsional Vibration Response of Multiple Rotating Blades with Underplatform Dampers

by Yanan Wu, Haijun Xuan, Changyao Wu, Dong Mi, Mingmin Qu and Tao Jin

Aerospace 2023, 10(8), 725; https://doi.org/10.3390/aerospace10080725 - 19 Aug 2023

Cited by 2 | Viewed by 1463

Abstract

Underplatform dampers (UPDs), a type of dry friction damper, are commonly used for vibration reduction of turbine blades. This study investigated the effect of UPDs on the forced torsional vibration response of turbine blades within a multi-blade system. Pre-stressed finite element modal analysis [...] Read more.

Underplatform dampers (UPDs), a type of dry friction damper, are commonly used for vibration reduction of turbine blades. This study investigated the effect of UPDs on the forced torsional vibration response of turbine blades within a multi-blade system. Pre-stressed finite element modal analysis and the harmonic balance method were combined to calculate the forced torsional vibration responses of a system with and without UPDs. The experiments were then carried out on a rotating multi-blade system with and without UPDs, with a focus on the effect of mass stacking on damping performance. The results showed that the installation of underplatform dampers could increase the frequency corresponding to the maximum response of the blade torsional vibration and cause multiple peaks that varied in the vibration response based on the mass of the UPDs. With an appropriate normal force, the underplatform dampers could effectively reduce the blade torsional vibration by 68.9%. However, excessive normal force of UPDs could lead to multiple large vibration peaks, which should be avoided in engineering practice. Additionally, the numerical results for the forced torsional vibration response of the rotating multi-blade system with UPDs were relatively close to the experimental results, indicating that the calculation method could be effectively applied to the nonlinear prediction of forced vibrations of rotating blades with dampers. Full article

► Show Figures

Figure 1

20 pages, 7736 KiB

Open AccessArticle

A Three-Dimensional Body Force Modeling of Fans in Windmilling Condition and Its Application

by Qingguo Kong and Wei Jia

Aerospace 2023, 10(8), 724; https://doi.org/10.3390/aerospace10080724 - 18 Aug 2023

Viewed by 1645

Abstract

To investigate the aerodynamic characteristics of the fan in windmilling conditions, a new body force model with the fan rotational speed prediction model was developed. The fan rotational speed prediction model was built based on the balance of fan output torque and resistance [...] Read more.

To investigate the aerodynamic characteristics of the fan in windmilling conditions, a new body force model with the fan rotational speed prediction model was developed. The fan rotational speed prediction model was built based on the balance of fan output torque and resistance torque. The rotational speed of the fan spool can be iteratively solved simultaneously with solving the governing equations without requiring mass flow rate or other inputs. The comparison with the experimental results shows that using the body force model can accurately predict the rotational speed of the fan spool under different operating conditions. The radial distribution of flow parameters can be obtained. Moreover, numerical simulations of the fan under different circumferential total pressure distortion inflow conditions were conducted using the body force model. The results show that, unlike the design point and non-design point at which the fan operates normally, the high radius region of the fan is in the “turbine mode” while the low radius region is in the “compressor mode” under windmilling conditions. The different effects on the longitudinal vortex in the two regions deepen and alleviate the circumferential distortion, respectively. There are strong circumferential and radial pressure gradients at the junction of the distortion-affected zone and the non-distortion-affected zone, adding additional mixing losses. Full article

► Show Figures

Figure 1

19 pages, 7132 KiB

Open AccessArticle

Correlation Studies of Different Decoupled Two-Scale Simulations for Lattice Structures

by Natsuki Tsushima, Ryo Higuchi and Koji Yamamoto

Aerospace 2023, 10(8), 723; https://doi.org/10.3390/aerospace10080723 - 18 Aug 2023

Cited by 2 | Viewed by 1815

Abstract

By deliberately designing microscopic internal mechanisms, architected materials can achieve a variety of material properties without changing constituent materials. Integration of the architected materials into a structure as substructures has a good potential to enhance structural performance and realize wide design freedom. This [...] Read more.

By deliberately designing microscopic internal mechanisms, architected materials can achieve a variety of material properties without changing constituent materials. Integration of the architected materials into a structure as substructures has a good potential to enhance structural performance and realize wide design freedom. This paper explores the capabilities of multiscale approaches for lattice structures, which is a major mechanism in architected materials. The objectives of this paper are (1) to demonstrate the capabilities of the framework to evaluate stiffness characteristics of lattice structures with two different two-scale analysis approaches and (2) to assess the accuracies and validity ranges of both approaches for appropriate evaluations of lattice structures. The two-scale analysis framework consists of the computational homogenizations for the generalized stiffness (ABD) and 3D stiffness (C) matrices. Equivalent stiffness characteristics of the unit cell are obtained by computational homogenizations to effectively capture the macroscopic responses of lattice structures. This study provides a comprehensive correlation study between the prediction accuracies of the two-scale analysis approaches in terms of tensile, bending, and torsional stiffness characteristics for practical modeling and development of lattice structures. The study will contribute a guideline for effective designs of high-performance structures with architected materials. Full article

(This article belongs to the Special Issue Structural Design of Aerospace Vehicles)

► Show Figures

Figure 1

17 pages, 4800 KiB

Open AccessArticle

Evaluation of Joint Clearance Effects on the Shimmy of Nose Landing Gear

by Yiyao Jiang, Guang Feng, Panglun Liu, Li Yuan, Jianbin Ding and Bingyan Jiang

Aerospace 2023, 10(8), 722; https://doi.org/10.3390/aerospace10080722 - 17 Aug 2023

Cited by 3 | Viewed by 2759

Abstract

Through the establishment of a three-dimensional joint clearance model, the effects of joint clearances at different positions on shimmy stability are evaluated. In this paper, considering the radial, axial and coupling characteristics of joint clearance, the shimmy multibody dynamics (MBD) model is applied [...] Read more.

Through the establishment of a three-dimensional joint clearance model, the effects of joint clearances at different positions on shimmy stability are evaluated. In this paper, considering the radial, axial and coupling characteristics of joint clearance, the shimmy multibody dynamics (MBD) model is applied to different joints in the nose landing gear (NLG) transmission system. It is proposed to evaluate the influence of joint clearance on shimmy from two aspects of position factor and wear factor. The study found that different joint clearances have different effects on shimmy: the joint clearance between the NLG and fuselage has little influence on shimmy; the larger axial clearance of upper and lower torque link joint will cause the shimmy of the NLG, but the radial clearance has no effect on shimmy; while the joint clearance between turning sleeve and upper torque link, lower torque link and piston only works in the axial and radial coupling. The reasons for the different influence characteristics of each joint space are analyzed. Consequently, studying and summarizing the influence of different clearance on shimmy is of great significance for the design and maintenance of the NLG joints. Full article

(This article belongs to the Special Issue Structural Dynamics and Control (2nd Edition))

► Show Figures

Figure 1

17 pages, 5615 KiB

Open AccessArticle

Study on Failure Criteria and the Numerical Simulation Method of a Coal-Based Carbon Foam under Multiaxial Loading

by Qikai Zhuang, Xiaoquan Cheng, Peijie Yue, Xin Guo and Kai Li

Aerospace 2023, 10(8), 721; https://doi.org/10.3390/aerospace10080721 - 17 Aug 2023

Cited by 1 | Viewed by 1289

Abstract

Coal-based carbon foam (CCF) has broad application prospects in aerospace, composite material tooling and other fields. However, the lack of failure criteria limits its promotion. In previous studies, the failure criteria of similar materials were proposed, but there are some limitations. This paper [...] Read more.

Coal-based carbon foam (CCF) has broad application prospects in aerospace, composite material tooling and other fields. However, the lack of failure criteria limits its promotion. In previous studies, the failure criteria of similar materials were proposed, but there are some limitations. This paper proposes improved failure criteria based on macro-mechanical tests. Furthermore, uniaxial and multiaxial loading tests were carried out to obtain accurate failure criteria of CCF. Finally, 3-points bending tests of the CCF sandwich structure were conducted and their finite element models (FEMs) were established. The CCF test results show that the mechanical properties of CCF are transversely isotropic. The failure criteria in this paper can accurately predict the stress when the CCF fails. The error band boundary formula caused by the dispersion of the material were also given. The maximum load P_max calculated by the failure surface (3684 N) was only 4.7% larger than the mean value measured by the test (3518 N), and all of the P_max measured by the test (3933 N, 3640 N, 3657 N, 3269 N, 3091 N) were between the maximum value (4297 N) and minimum value (3085 N) calculated by the error band boundary formula, which means that the failure criteria have good precision. Full article

(This article belongs to the Special Issue Advanced Aerospace Composite Materials)

► Show Figures

Figure 1

19 pages, 5408 KiB

Open AccessArticle

Parametric Investigation of Leading-Edge Slats on a Blended-Wing-Body UAV Using the Taguchi Method

by Spyridon Antoniou, Stavros Kapsalis, Pericles Panagiotou and Kyros Yakinthos

Aerospace 2023, 10(8), 720; https://doi.org/10.3390/aerospace10080720 - 17 Aug 2023

Cited by 3 | Viewed by 1920

Abstract

The current study investigated the effect of leading-edge slats on the longitudinal stability at high angles of attack of a Blended-Wing-Body (BWB) Unmanned Air Vehicle (UAV). Using a Design of Experiments (DOE) approach and, specifically, the Taguchi method, four leading-edge slat design parameters [...] Read more.

The current study investigated the effect of leading-edge slats on the longitudinal stability at high angles of attack of a Blended-Wing-Body (BWB) Unmanned Air Vehicle (UAV). Using a Design of Experiments (DOE) approach and, specifically, the Taguchi method, four leading-edge slat design parameters were investigated on three different levels. These parameters were the slat semi-span, the rotation of the slat element, the extension forward of the leading edge and the downward drop below the leading edge. An L₉ orthogonal array (OA) was used to investigate the influence of these key design parameters using three performance criteria, namely the angle at which pitch break occurs, the corresponding speed and the distance between the Neutral point of each configuration and the Neutral point of the reference platform. The investigation was conducted by using high-fidelity Computational Fluid Dynamics (CFD) methods for each of the nine configurations defined by the L₉ OA, over a range of angles of attack between −4 and 16 degrees. Based on these results, and using a Signal-to-Noise ratio (SNR) analysis, two combinations were eventually derived, one that optimized pitch break angle and speed and one that optimized longitudinal stability. Finally, the Pareto Analysis of Variance (ANOVA) technique was conducted to define the contribution of each of the six design parameters on the selected performance criteria. More specifically, the semi-span seemed to have the most significant effect on pitch break angle and speed, whereas the rotation of the slat element was the most important parameter with regard to static stability. Full article

► Show Figures

Figure 1

14 pages, 1672 KiB

Open AccessArticle

Crew Interaction in Extended Space Missions

by Alla Vinokhodova, Vadim Gushin, Polina Kuznetsova and Anna Yusupova

Aerospace 2023, 10(8), 719; https://doi.org/10.3390/aerospace10080719 - 16 Aug 2023

Cited by 3 | Viewed by 1355

Abstract

Detection of the extent of common values in a cohesive space crew has become an important trend in modern space psychology. It is known from the works of Ch. Osgood that the semantic differential scale is a reliable way to obtain objective information [...] Read more.

Detection of the extent of common values in a cohesive space crew has become an important trend in modern space psychology. It is known from the works of Ch. Osgood that the semantic differential scale is a reliable way to obtain objective information on the emotional attitudes towards a topic of interest. Within the frame of the Russian space experiment “Interactions” on the International Space Station (ISS), a computerized survey, the Personal Self-Perception and Attitudes (PSPA), was developed for analyzing the subjects’ emotional attitudes toward their social environment. In the course of the PSPA procedure, the crewmembers rate each other and themselves (in the past, present, and future) using the criteria previously personally chosen. These criteria should be regarded as their personal values. A total of 30 subjects have already completed the study on board the ISS. The main tasks of the study are: (1) to define individual and group values and the extent of group identification reflected in sharing these values; (2) to determine the impact of cross-cultural factors on mutual perceptions and self-perceptions in space crews and with the Mission Control Center (MCC); (3) to study changes in the space crews’ group cohesiveness and structure as they are exposed to the stress of the extended space mission environment. The data obtained indicate an increase in a “psychological distance” between the crew and the MCC personnel versus increased crew cohesion. The results gained made it possible to identify the most significant categories of values common to the subjects from the professional cosmonaut group. The priority of these shared values for each subject is an important condition for the formation of a cohesive crew. Full article

(This article belongs to the Special Issue Human Behaviors in Space Exploration Mission)

► Show Figures

Figure 1

30 pages, 8044 KiB

Open AccessArticle

EVTOL Tilt-Wing Aircraft Design under Uncertainty Using a Multidisciplinary Possibilistic Approach

by Mohsen Rostami, Julian Bardin, Daniel Neufeld and Joon Chung

Aerospace 2023, 10(8), 718; https://doi.org/10.3390/aerospace10080718 - 16 Aug 2023

Cited by 10 | Viewed by 3577

Abstract

Recent development in Electric Vertical Take-off and Landing (eVTOL) aircraft makes it a popular design approach for urban air mobility (UAM). When designing these configurations, due to the uncertainty present in semi-empirical estimations, often used for aerodynamic characteristics during the conceptual design phase, [...] Read more.

Recent development in Electric Vertical Take-off and Landing (eVTOL) aircraft makes it a popular design approach for urban air mobility (UAM). When designing these configurations, due to the uncertainty present in semi-empirical estimations, often used for aerodynamic characteristics during the conceptual design phase, results can only be trusted to approximately 80% accuracy. Accordingly, an optimized aircraft using semi-empirical estimations and deterministic multi-disciplinary design optimization (MDO) approaches can be at risk of not being certifiable in the detailed design phase of the life cycle. The focus of this study was to implement a robust and efficient possibility-based design optimization (PBDO) method for the MDO of an eVTOL tilt-wing aircraft in the conceptual design phase, using existing conventional designs as an initial configuration. As implemented, the optimization framework utilizes a deterministic gradient-based optimizer, run sequentially with a possibility assessment algorithm, to select an optimal design. To achieve this, the uncertainties which arise from multi-fidelity calculations, such as semi-empirical methods, are considered and used to modify the final design such that its viability is guaranteed in the detailed design phase. With respect to various requirements, including trim, stability, and control behaviors, the optimized eVTOL tilt-wing aircraft design offers the preferred results which ensure that airworthiness criteria are met whilst complying with predefined constraints. The proposed approach may be used to revise currently available light aircraft and develop eVTOL versions from the original light aircraft. The resulting aircraft is not only an optimized layout but one where the stability of the eVTOL tilt-wing aircraft has been guaranteed. Full article

(This article belongs to the Special Issue E-VTOL Simulation and Autonomous System Development)

► Show Figures

Figure 1

21 pages, 6215 KiB

Open AccessArticle

Low-Boom Design for Supersonic Transport with Canard and Forward-Swept Wings Using Equivalent Area Design Method

by Yuki Kishi, Risato Yashiro and Masahiro Kanazaki

Aerospace 2023, 10(8), 717; https://doi.org/10.3390/aerospace10080717 - 16 Aug 2023

Cited by 3 | Viewed by 2675

Abstract

Forward-swept wings can be expected to be lower-boom planforms with similar amount of drag as backward-swept wings because of their good lift distributions. In this study, the equivalent area distribution of a ten-seater supersonic forward-swept wing aircraft with a canard was designed to [...] Read more.

Forward-swept wings can be expected to be lower-boom planforms with similar amount of drag as backward-swept wings because of their good lift distributions. In this study, the equivalent area distribution of a ten-seater supersonic forward-swept wing aircraft with a canard was designed to obtain design knowledge for leading boom reduction. The equivalent area distribution of the aircraft was calculated by solving the compressible Euler equation. A feasible target equivalent area distribution was generated based on Darden’s method and compared with the equivalent area distribution. To achieve a closer match in terms of lift and geometry with the target, the main wing planform and the position of the main wing along the body and vertical axes were modified. The low-boom performances were evaluated using the extended Burgers equation. The design results indicated that the forward-swept wing configuration with a canard could divide the single peak of the leading boom into two peaks. Thus, the sonic boom strength of the canard configuration was 2.5 PLdB lower than that of the configuration without the canard wing. Full article

(This article belongs to the Special Issue Research and Development of Supersonic Aircraft)

► Show Figures

Figure 1

26 pages, 11740 KiB

Open AccessArticle

Optimizing the Location of the Piezoelectric Actuator and Analyzing Its Effect on the Dynamics of Asymmetric Flexible Spacecraft

by Kai Cao, Renyuan Xie, Jianmin Zhou, Xiaowei Zhang, Jingji Wang and Shuang Li

Aerospace 2023, 10(8), 716; https://doi.org/10.3390/aerospace10080716 - 16 Aug 2023

Viewed by 1247

Abstract

To address the challenge of optimizing the placement of actuators on an asymmetric spacecraft continuum system, this paper develops a rigid–flexible electromechanical coupling dynamic model that integrates the interactions among rigidity, flexibility, and electromechanical coupling effects. The model is constructed using ordinary differential [...] Read more.

To address the challenge of optimizing the placement of actuators on an asymmetric spacecraft continuum system, this paper develops a rigid–flexible electromechanical coupling dynamic model that integrates the interactions among rigidity, flexibility, and electromechanical coupling effects. The model is constructed using ordinary differential equations and partial differential equations (ODE–PDEs) and considers the effects of the installation position and physical characteristics (mass and stiffness) of the piezoelectric (PZT) actuator on an asymmetric flexible spacecraft continuum system. The proposed model aims to accurately capture the complex interactions among the rigid body, flexible appendages, and PZT actuators. Based on the developed model, the installation location of the actuators is optimized using a genetic algorithm with a hybrid optimization criterion. In the numerical simulations, the proposed optimization algorithm is employed to determine the optimal installation position for the actuators. Then, the influence of the actuator’s physical characteristics and installation position on the dynamic properties of the spacecraft and the performance of the control system is investigated. The numerical simulation results demonstrate that the optimization algorithm can effectively identify the appropriate actuator installation location for the desired application. Utilizing the actuator with the optimized position allows for effective vibration suppression while consuming less energy. Full article

► Show Figures

Figure 1

16 pages, 493 KiB

Open AccessArticle

Remaining Useful Life Prediction for Turbofan Engine Using SAE-TCN Model

by Xiaofeng Liu, Liuqi Xiong, Yiming Zhang and Chenshuang Luo

Aerospace 2023, 10(8), 715; https://doi.org/10.3390/aerospace10080715 - 16 Aug 2023

Cited by 7 | Viewed by 1781

Abstract

Turbofan engines are known as the heart of the aircraft. The turbofan’s health state determines the aircraft’s operational status. Therefore, the equipment monitoring and maintenance of the engine is an important part of ensuring the healthy and stable operation of the aircraft, and [...] Read more.

Turbofan engines are known as the heart of the aircraft. The turbofan’s health state determines the aircraft’s operational status. Therefore, the equipment monitoring and maintenance of the engine is an important part of ensuring the healthy and stable operation of the aircraft, and it is vital to monitor the remaining useful life (RUL) of the engine. The monitored data of turbofan engines have high dimensions and a long time span, which cause difficulties in predicting the remaining useful life of the engine. This paper proposes a residual life prediction model based on Autoencoder and a Temporal Convolutional Network (TCN). Among them, Autoencoder is used to reduce the dimension of the data and extract features from the engine monitoring data. The TCN network is trained on the obtained low-dimensional data to predict the remaining useful life. The model mentioned in this article is verified on the NASA public data set (C-MAPSS) and compared with common machine learning methods and other deep neural networks. The SAE-TCN model achieved better scores on the FD001 independent testing data set with an RMSE of 18.01 and a score of 161. The average relative error of the model relative to other common learning models is 0.9499 in RMSE and 0.2656 in Scoring Function. The experimental results show that the model proposed in this paper performs the best in the evaluation, and this conclusion has important implications for engine health. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

22 pages, 8976 KiB

Open AccessArticle

Nonlinear Time Series Analysis and Prediction of General Aviation Accidents Based on Multi-Timescales

by Yufei Wang, Honghai Zhang, Zongbei Shi, Jinlun Zhou and Wenquan Liu

Aerospace 2023, 10(8), 714; https://doi.org/10.3390/aerospace10080714 - 16 Aug 2023

Cited by 1 | Viewed by 1597

Abstract

General aviation accidents have complex interactions and influences within them that cannot be simply explained and predicted by linear models. This study is based on chaos theory and uses general aviation accident data to conduct research on different timescales (HM-scale, ET-scale [...] Read more.

General aviation accidents have complex interactions and influences within them that cannot be simply explained and predicted by linear models. This study is based on chaos theory and uses general aviation accident data to conduct research on different timescales (HM-scale, ET-scale, and EF-scale). First, time series are constructed by excluding seasonal patterns from the statistics of general aviation accidents. Secondly, the chaotic properties of multi-timescale series are determined by the 0–1 test and Lyapunov exponent. Finally, by introducing the sparrow search algorithm and tent chaotic mapping, a CSSA-LSSVM prediction model is proposed. The accident data of the National Transportation Safety Board (NTSB) of the United States in the past 15 years is selected for case analysis. The results show that the phase diagram of the 0–1 test presents Brownian motion characteristics, and the maximum Lyapunov exponents of the three scales are all positive, proving the chaotic characteristics of multi-timescale series. The CSSA-LSSVM prediction model’s testing results illustrate its superiority in time series predicting, and when the timescale declines, the prediction error reduces gradually while the fitting effect strengthens and then decreases. This study uncovers the nonlinear chaotic features of general aviation accidents and demonstrates the significance of multi-timescale research in time series analysis and prediction. Full article

(This article belongs to the Section Air Traffic and Transportation)

► Show Figures

Figure 1

28 pages, 18145 KiB

Open AccessArticle

Experimental Investigation of a Swirling-Oxidizer-Flow-Type Hybrid Rocket Engine Using Low-Melting-Point Thermoplastic Fuel and Oxygen

by Tsuyoshi Oishi, Mitsuru Tamari and Takashi Sakurai

Aerospace 2023, 10(8), 713; https://doi.org/10.3390/aerospace10080713 - 15 Aug 2023

Viewed by 2190

Abstract

Hybrid rockets are safe and inexpensive; however, boundary-layer combustion poses a problem in achieving a fuel regression rate equivalent to that of solid propellants. The fundamental combustion conditions, such as the fuel regression rate of LT421, a paraffin-based low-melting-point thermoplastic fuel, were investigated [...] Read more.

Hybrid rockets are safe and inexpensive; however, boundary-layer combustion poses a problem in achieving a fuel regression rate equivalent to that of solid propellants. The fundamental combustion conditions, such as the fuel regression rate of LT421, a paraffin-based low-melting-point thermoplastic fuel, were investigated using a swirling-flow combustion method. Firing tests were conducted using the oxygen mass flow rate and burn time parameters. The LT fuel exhibited an ignition delay compared to polypropylene, and the pressure increased slowly relative to the thrust. The combustion pressure increased or remained constant with time, suggesting that the fuel regression rate was more dependent on the oxygen mass flow rate than the oxidizer mass flux. The shear force generated in the grain owing to the swirling flow caused fuel-grain separation when the oxygen mass flow rate exceeded 100 g/s. Fuel-grain separation was prevented by modifying the case geometry. The maximum fuel regression rate obtained in the tests was 4.88 mm/s at an oxygen mass flow rate of 190 g/s and mass flux of 72.4 kg/(m²s), which was four times higher than that of polypropylene at the same oxidizer mass flux. The fuel regression rate correlation was obtained using the oxygen mass-flow-rate-based parameter, although further modification was necessary to apply this correlation when the burning time was varied. Full article

(This article belongs to the Special Issue Hybrid Rocket Engines)

► Show Figures

Figure 1

17 pages, 12203 KiB

Open AccessArticle

The Development of an Advanced Air Mobility Flight Testing and Simulation Infrastructure

by Arinc Tutku Altun, Mehmet Hasanzade, Emre Saldiran, Guney Guner, Mevlut Uzun, Rodolphe Fremond, Yiwen Tang, Prithiviraj Bhundoo, Yu Su, Yan Xu, Gokhan Inalhan, Michael W. Hardt, Alejandro Fransoy, Ajay Modha, Jose Antonio Tena, Cesar Nieto, Miguel Vilaplana, Marta Tojal, Victor Gordo, Pablo Menendez and Ana Gonzalez Show full author list Hide full author list

Aerospace 2023, 10(8), 712; https://doi.org/10.3390/aerospace10080712 - 15 Aug 2023

Cited by 6 | Viewed by 3045

Abstract

The emerging field of Advanced Air Mobility (AAM) holds great promise for revolutionizing transportation by enabling the efficient, safe, and sustainable movement of people and goods in urban and regional environments. AAM encompasses a wide range of electric vertical take-off and landing (eVTOL) [...] Read more.

The emerging field of Advanced Air Mobility (AAM) holds great promise for revolutionizing transportation by enabling the efficient, safe, and sustainable movement of people and goods in urban and regional environments. AAM encompasses a wide range of electric vertical take-off and landing (eVTOL) aircraft and infrastructure that support their operations. In this work, we first present a new airspace structure by considering different layers for standard-performing vehicles (SPVs) and high-performing vehicles (HPVs), new AAM services for accommodating such a structure, and a holistic contingency management concept for a safe and efficient traffic environment. We then identify the requirements and development process of a testing and simulation infrastructure for AAM demonstrations, which specifically aim to explore the decentralized architecture of the proposed concept and its use cases. To demonstrate the full capability of AAM, we develop an infrastructure that includes advanced U-space services, real and simulated platforms that are suitable for future AAM use cases such as air cargo delivery and air taxi operations, and a co-simulation environment that allows all of the AAM elements to interact with each other in harmony. The considered infrastructure is envisioned to be used in AAM integration-related efforts, especially those focusing on U-space service deployment over a complex traffic environment and those analyzing the interaction between the operator, the U-space service provider (USSP), and the air traffic controller (ATC). Full article

(This article belongs to the Special Issue Advanced Air Mobility)

► Show Figures

Figure 1

19 pages, 664 KiB

Open AccessArticle

Research on Unmanned Aerial Vehicle Cluster Collaborative Countermeasures Based on Dynamic Non-Zero-Sum Game under Asymmetric and Uncertain Information

by Pengcheng Wu, Hongqiao Wang, Gaowei Liang and Peng Zhang

Aerospace 2023, 10(8), 711; https://doi.org/10.3390/aerospace10080711 - 15 Aug 2023

Cited by 3 | Viewed by 1616

Abstract

Unmanned aerial vehicle (UAV) swarm coordinated confrontation is a hot topic in academic research at home and abroad, and dynamic maneuver decision-making is one of the most important research fields for UAV countermeasures. Aiming at the complexity, uncertainty and confrontation of UAV cooperative [...] Read more.

Unmanned aerial vehicle (UAV) swarm coordinated confrontation is a hot topic in academic research at home and abroad, and dynamic maneuver decision-making is one of the most important research fields for UAV countermeasures. Aiming at the complexity, uncertainty and confrontation of UAV cooperative confrontation, concepts such as relative advantage degree and advantage coefficient are introduced, and game theory is used as a framework to construct a dynamic non-zero-sum game UAV cluster cooperative confrontation decision-making model, and finally convert it into an optimization problem. On this basis, using the Nash equilibrium solution method of multi-strategy fusion particle swarm algorithm, by introducing adaptive inertia weight and local mutation strategy, while enhancing the diversity of the population, it can ensure the local accurate search ability of the particle swarm. The simulation results of the example are verified. The effectiveness of the proposed model and method is confirmed. Full article

► Show Figures

Figure 1

17 pages, 1798 KiB

Open AccessArticle

On the Potentials of the Integration of Pressure Gain Combustion with a Hybrid Electric Propulsion System

by Dongsuk Kim, Majid Asli and Klaus Höschler

Aerospace 2023, 10(8), 710; https://doi.org/10.3390/aerospace10080710 - 15 Aug 2023

Cited by 1 | Viewed by 1579

Abstract

As the issue of pollutant emissions from aviation propulsion escalates, research into alternative powertrains is gaining momentum. Two promising technologies are the Hybrid Electric Propulsion System (HEPS) and Pressure Gain Combustion (PGC). HEPS is expected to reduce pollutant emissions by decreasing fuel consumption, [...] Read more.

As the issue of pollutant emissions from aviation propulsion escalates, research into alternative powertrains is gaining momentum. Two promising technologies are the Hybrid Electric Propulsion System (HEPS) and Pressure Gain Combustion (PGC). HEPS is expected to reduce pollutant emissions by decreasing fuel consumption, whereas PGC uses detonation in the combustor to increase the thermal efficiency of engines by elevating the total pressure during combustion. This study extensively explores the integration of these two emerging technologies, thoroughly assessing the advantages that arise from their combination. First, the renowned turboprop engine PW127 is benchmarked and modeled using Gasturb software. The model is integrated into Simulink using the T-MATS tool, with HEPS and pressure gain components added to analyze the thermodynamics of various configurations under different pressure gain values and HEPS parameters. The analysis, conducted up to the cruise phase of the baseline aircraft, reveals that applying pressure gain combustion through Rotating Detonation Combustion (RDC) results in a more significant increase in efficiency and decrease in fuel consumption compared to HEPS with conventional gas turbines. However, HEPS helps maintain a more uniform combustor inlet condition and reduces the Turbine Inlet Temperature (TIT) at the takeoff phase, where the highest TIT otherwise occurs. The results suggest that integrating HEPS with PGC can be beneficial in maintaining optimal combustor conditions and mitigating turbine efficiency degradation. Full article

► Show Figures

Figure 1

28 pages, 12410 KiB

Open AccessArticle

A Stealth–Distance Dynamic Weight Deep Q-Network Algorithm for Three-Dimensional Path Planning of Unmanned Aerial Helicopter

by Zeyang Wang, Jun Huang and Mingxu Yi

Aerospace 2023, 10(8), 709; https://doi.org/10.3390/aerospace10080709 - 15 Aug 2023

Cited by 2 | Viewed by 1286

Abstract

Unmanned aerial helicopters (UAHs) have been widely used recently for reconnaissance operations and other risky missions. Meanwhile, the threats to UAHs have been becoming more and more serious, mainly from radar and flights. It is essential for a UAH to select a safe [...] Read more.

Unmanned aerial helicopters (UAHs) have been widely used recently for reconnaissance operations and other risky missions. Meanwhile, the threats to UAHs have been becoming more and more serious, mainly from radar and flights. It is essential for a UAH to select a safe flight path, as well as proper flying attitudes, to evade detection operations, and the stealth abilities of the UAH can be helpful for this. In this paper, a stealth–distance dynamic weight Deep Q-Network (SDDW-DQN) algorithm is proposed for path planning in a UAH. Additionally, the dynamic weight is applied in the reward function, which can reflect the priorities of target distance and stealth in different flight states. For the path-planning simulation, the dynamic model of UAHs and the guidance model of flight are put forward, and the stealth model of UAHs, including the radar cross-section (RCS) and the infrared radiation (IR) intensity of UAHs, is established. The simulation results show that the SDDW-DQN algorithm can be helpful in the evasion by UAHs of radar detection and flight operations, and the dynamic weight can contribute to better path-planning results. Full article

► Show Figures

Figure 1

25 pages, 722 KiB

Open AccessArticle

Long-Distance GNSS-Denied Visual Inertial Navigation for Autonomous Fixed-Wing Unmanned Air Vehicles: SO(3) Manifold Filter Based on Virtual Vision Sensor

by Eduardo Gallo and Antonio Barrientos

Aerospace 2023, 10(8), 708; https://doi.org/10.3390/aerospace10080708 - 14 Aug 2023

Cited by 1 | Viewed by 2350

Abstract

This article proposes a visual inertial navigation algorithm intended to diminish the horizontal position drift experienced by autonomous fixed-wing UAVs (unmanned air vehicles) in the absence of GNSS (Global Navigation Satellite System) signals. In addition to accelerometers, gyroscopes, and magnetometers, the proposed navigation [...] Read more.

This article proposes a visual inertial navigation algorithm intended to diminish the horizontal position drift experienced by autonomous fixed-wing UAVs (unmanned air vehicles) in the absence of GNSS (Global Navigation Satellite System) signals. In addition to accelerometers, gyroscopes, and magnetometers, the proposed navigation filter relies on the accurate incremental displacement outputs generated by a VO (visual odometry) system, denoted here as a virtual vision sensor, or VVS, which relies on images of the Earth surface taken by an onboard camera and is itself assisted by filter inertial estimations. Although not a full replacement for a GNSS receiver since its position observations are relative instead of absolute, the proposed system enables major reductions in the GNSS-denied attitude and position estimation errors. The filter is implemented in the manifold of rigid body rotations or

SO (3)

in order to minimize the accumulation of errors in the absence of absolute observations. Stochastic high-fidelity simulations of two representative scenarios involving the loss of GNSS signals are employed to evaluate the results. The authors release the C++ implementation of both the visual inertial navigation filter and the high-fidelity simulation as open-source software. Full article

(This article belongs to the Special Issue Advanced Air Mobility)

► Show Figures

Figure 1

27 pages, 43650 KiB

Open AccessArticle

Influence of Variable-Geometry Adjustment on the Matching Characteristics of a Medium Variable Bypass Ratio Compression System

by Qiaodan Luo, Shengfeng Zhao, Shiji Zhou, Huafeng Xu and Xiaoying Sheng

Aerospace 2023, 10(8), 707; https://doi.org/10.3390/aerospace10080707 - 14 Aug 2023

Cited by 1 | Viewed by 1291

Abstract

The research is based on a full 3D model of a medium variable bypass ratio compression system. The effects of core-driven fan stage (CDFS) VIGV adjustment and forward variable area bypass injector (FVABI) adjustment on the internal flow and component matching characteristics of [...] Read more.

The research is based on a full 3D model of a medium variable bypass ratio compression system. The effects of core-driven fan stage (CDFS) VIGV adjustment and forward variable area bypass injector (FVABI) adjustment on the internal flow and component matching characteristics of the compression system during the mode transition process are investigated. The findings of the study reveal that during the mode transition period, the adjustment of variable-geometry components has a negligible impact on the aerodynamic performance of the fan. The closure of the CDFS VIGV has a significant effect on reducing the pressure ratio of the CDFS but only a minor effect on its efficiency. Additionally, the efficiency and pressure ratio of the high-pressure compressor (HPC) increase with the closure of the CDFS VIGV, particularly the second stage of the HPC. When the CDFS VIGV is closed by 30°, the efficiency of the second stage of the HPC increases by 3.4%, while that of the first stage only increases by 3.1%. Under the high bypass mode, increasing the FVABI opening will move the matching point of the CDFS towards the choke boundary. When the FVABI opening increases from 0.30 to 0.58, the efficiency of the CDFS decreases by 3.6%, while the efficiency of the HPC only increases by 0.4%. In summary, closing the CDFS VIGV and increasing the opening of the FVABI will increase the bypass ratio of the compression system, and the former has a more significant impact. When the compression system transitions from the low bypass mode to the high bypass mode, opening of the FVABI should be appropriately reduced to prevent CDFS matching in the operating condition too closely to the choke boundary, thereby maintaining the efficiency of each component of the compression system at a relatively high level. Full article

(This article belongs to the Section Aeronautics)

► Show Figures

Figure 1

21 pages, 9116 KiB

Open AccessArticle

Experimental Study on the Ignition Characteristics of Scramjet Combustor with Tandem Cavities Using Micro-Pulse Detonation Engine

by Min-Su Kim, In-Hoi Koo, Keon-Hyeong Lee, Eun-Sung Lee, Hyung-Seok Han, Seung-Min Jeong, Holak Kim and Jeong-Yeol Choi

Aerospace 2023, 10(8), 706; https://doi.org/10.3390/aerospace10080706 - 11 Aug 2023

Cited by 3 | Viewed by 1970

Abstract

This experimental investigation focused on the ignition and combustion characteristics of a tandem cavity-based scramjet combustor with side-by-side identical cavities. This study utilized the Pusan National University-direct connect scramjet combustor (PNU-DCSC), which was capable of simulating flight conditions at Mach number 4.0–5.0 and [...] Read more.

This experimental investigation focused on the ignition and combustion characteristics of a tandem cavity-based scramjet combustor with side-by-side identical cavities. This study utilized the Pusan National University-direct connect scramjet combustor (PNU-DCSC), which was capable of simulating flight conditions at Mach number 4.0–5.0 and altitudes of 20–25 km using the vitiated air heater (VAH). The combustion tests were conducted under off-design point conditions corresponding to low inlet enthalpy. It is a condition in which self-ignition does not occur, and a micro pulse detonation engine (μPDE) ignitor is used. The results revealed that as the injection pressure of the gaseous hydrogen fuel (GH₂) and the corresponding equivalence ratio increased, the combustion mode transitioned from the cavity-shear layer flame to the jet-wake flame. Furthermore, the measured wall static pressure profiles along the isolator and scramjet combustor indicated that the region of elevated pressure distribution caused by the shock train expanded upstream with higher equivalence ratios. When ignited from the secondary cavity, the combustion area did not extend to the primary cavity at lower equivalence ratios, while it expanded upstream faster with higher equivalence ratios. Therefore, the combustion characteristics of the tandem cavity were found to vary based on the overall equivalence ratio of the main fuel (GH₂) and ignition position. Full article

► Show Figures

Figure 1

Journal Menu

Journal Browser

Aerospace, Volume 10, Issue 8 (August 2023) – 77 articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI