Gels | Special Issue : Gel-Based Materials: Preparations and Characterization (2nd Edition)

Research

Jump to: Review

20 pages, 5385 KiB

Open AccessArticle

Studies on the Powerful Photoluminescence of the Lu₂O₃:Eu³⁺ System in the Form of Ceramic Powders and Crystallized Aerogels

by Alan D. Alcantar Mendoza, Antonieta García Murillo, Felipe de J. Carrillo Romo and José Guzmán Mendoza

Gels 2024, 10(11), 736; https://doi.org/10.3390/gels10110736 - 13 Nov 2024

Viewed by 379

Abstract

This study compared the chemical, structural, and luminescent properties of xerogel-based ceramic powders (CPs) with those of a new series of crystallized aerogels (CAs) synthesized by the epoxy-assisted sol–gel process. Materials with different proportions of Eu³⁺ (2, 5, 8, and 10 mol%) [...] Read more.

This study compared the chemical, structural, and luminescent properties of xerogel-based ceramic powders (CPs) with those of a new series of crystallized aerogels (CAs) synthesized by the epoxy-assisted sol–gel process. Materials with different proportions of Eu³⁺ (2, 5, 8, and 10 mol%) were synthesized in Lu₂O₃ host matrices, as well as a Eu₂O₃ matrix for comparative purposes. The products were analyzed by infrared spectroscopy (IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), transmission electron microscopy (TEM), photoluminescence analysis, and by the Brunauer–Emmett–Teller (BET) technique. The results show a band associated with the M-O bond, located at around 575 cm⁻¹. XRD enabled us to check two ensembles: matrices (Lu₂O₃ or Eu₂O₃) and doping (Lu₂O₃:Eu³⁺) with appropriate chemical compositions featuring C-type crystal structures and intense reflections by the (222) plane, with an interplanar distance of around 0.3 nm. Also, the porous morphology presented by the materials consisted of interconnected particles that formed three-dimensional networks. Finally, emission bands due to the energy transitions (⁵D_J, where J = 0, 1, 2, and 3) were caused by the Eu³⁺ ions. The samples doped at 10 mol% showed orange-pink photoluminescence and had the longest disintegration times and greatest quantum yields with respect to the crystallized Eu₂O₃ aerogel. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

17 pages, 11316 KiB

Open AccessArticle

Effects of Moisture Content and Heat Treatment on the Viscoelasticity and Gelation of Polyacrylonitrile/Dimethylsulfoxide Solutions

by Jae-Yeon Yang, Yun-Su Kuk, Byoung-Suhk Kim and Min-Kang Seo

Gels 2024, 10(11), 728; https://doi.org/10.3390/gels10110728 - 10 Nov 2024

Viewed by 414

Abstract

Polyacrylonitrile (PAN) gels create significant obstacles in industrial fiber spinning by forming insoluble networks that compromise solution stability and uniformity. This study investigates the rheological properties of PAN/dimethyl sulfoxide (DMSO) solutions, examining how aging time, moisture content, and polymer concentration affect gelation behavior. [...] Read more.

Polyacrylonitrile (PAN) gels create significant obstacles in industrial fiber spinning by forming insoluble networks that compromise solution stability and uniformity. This study investigates the rheological properties of PAN/dimethyl sulfoxide (DMSO) solutions, examining how aging time, moisture content, and polymer concentration affect gelation behavior. Dynamic rheological analysis revealed that both physical and chemical crosslinks play crucial roles in gel formation, with gelation accelerating markedly when moisture content exceeds 3% and aging progresses. Under heat treatment at 80 °C, samples with increased moisture content demonstrated rapid transitions to solid-like states, indicating a critical moisture threshold for enhanced gelation kinetics. Additionally, reductions in polymer concentration disrupted physical crosslink density, thereby mitigating gel formation. These results underscore the importance of precisely controlling moisture and concentration parameters in PAN solutions to stabilize solution properties and minimize gel formation, thus enhancing process efficiency and quality in PAN-based carbon fiber production. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Graphical abstract

12 pages, 2747 KiB

Open AccessArticle

Evaluation of Mixing Temperature in the Preparation of Plant-Based Bigels

by Marcela Quilaqueo, Sonia Millao, Eduardo Morales, Mónica Rubilar and Ingrid Contardo

Gels 2024, 10(11), 725; https://doi.org/10.3390/gels10110725 - 9 Nov 2024

Viewed by 375

Abstract

Understanding gel structures and behavior is a prerequisite for attaining the desired food application characteristics. The mixing temperature is crucial when incorporating thermolabile active compounds into gels. This study evaluated the effect of mixing temperature on the physical and chemical properties of a [...] Read more.

Understanding gel structures and behavior is a prerequisite for attaining the desired food application characteristics. The mixing temperature is crucial when incorporating thermolabile active compounds into gels. This study evaluated the effect of mixing temperature on the physical and chemical properties of a bigel system prepared using a carnauba wax/canola oil oleogel and Arabic gum hydrogels. The results showed that bigels prepared at lower temperatures (30 and 40 °C) resulted in a solid-like state under crystallization temperature, resulting in matrices with larger hydrogel droplets, softer texture, and lower adhesiveness, spreadability, and solvent binding capacity. In contrast, bigels prepared at higher temperatures (50 and 60 °C), around crystallization temperature but with no solid state, resulted in matrices with smaller hydrogel droplets and higher firmness, adhesiveness, and spreadability. These bigels had a higher apparent viscosity, especially at lower shear rates, and solid-like behavior in the linear viscosity range. During the bigel preparation process, adjusting the mixture temperature had no effect on the samples’ oxidative stability, FTIR spectra, or thermal properties. The results highlighted the importance of hydrogel droplet size on the microstructure of the formed bigels, and smaller droplets could act as effective fillers to reinforce the matrix without making chemical changes. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

16 pages, 7227 KiB

Open AccessArticle

Use of Chitosan–Iron Oxide Gels for the Removal of Cd²⁺ Ions from Aqueous Solutions

by Eduardo Mendizábal, Nely Ríos-Donato, Minerva Guadalupe Ventura-Muñoz, Rosaura Hernández-Montelongo and Ilse Paulina Verduzco-Navarro

Gels 2024, 10(10), 630; https://doi.org/10.3390/gels10100630 - 30 Sep 2024

Viewed by 653

Abstract

High-quality water availability is substantial for sustaining life, so its contamination presents a serious problem that has been the focus of several studies. The presence of heavy metals, such as cadmium, is frequently studied due to the increase in the contamination levels caused [...] Read more.

High-quality water availability is substantial for sustaining life, so its contamination presents a serious problem that has been the focus of several studies. The presence of heavy metals, such as cadmium, is frequently studied due to the increase in the contamination levels caused by fast industrial expansion. Cadmium ions were removed from aqueous solutions at pH 7.0 by chitosan–magnetite (ChM) xerogel beads and chitosan–FeO (ChF) xerogel beads in batch systems. Kinetic studies were best modeled by the Elovich model. The adsorption isotherms obtained showed an inflection point suggesting the formation of a second layer, and the BET model adjusted to liquid–solid systems was adequate for the description of the experimental data. Maximum uptake capacities of 36.97 ± 0.77 and 28.60 ± 2.09 mg Cd/g xerogel were obtained for ChM and ChF, respectively. The studied composites are considered promising adsorbent materials for removing cadmium ions from aqueous systems. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Graphical abstract

21 pages, 7675 KiB

Open AccessArticle

Analysis of Structural Changes of pH–Thermo-Responsive Nanoparticles in Polymeric Hydrogels

by Lazaro Ruiz-Virgen, Miguel Angel Hernandez-Martinez, Gabriela Martínez-Mejía, Rubén Caro-Briones, Enrique Herbert-Pucheta, José Manuel del Río and Mónica Corea

Gels 2024, 10(8), 541; https://doi.org/10.3390/gels10080541 - 20 Aug 2024

Viewed by 1200

Abstract

The pH- and thermo-responsive behavior of polymeric hydrogels

(M_{C} - c o - M_{A})

have been studied in detail using dynamic light scattering

(D L S)

, scanning electron microscopy

(S E M)

, nuclear magnetic resonance (¹H [...] Read more.

The pH- and thermo-responsive behavior of polymeric hydrogels

(M_{C} - c o - M_{A})

have been studied in detail using dynamic light scattering

(D L S)

, scanning electron microscopy

(S E M)

, nuclear magnetic resonance (¹H NMR) and rheology to evaluate the conformational changes, swelling–shrinkage, stability, the ability to flow and the diffusion process of nanoparticles at several temperatures. Furthermore, polymeric systems functionalized with acrylic acid

(M_{C})

and acrylamide

(M_{A})

were subjected to a titration process with a calcium chloride

({C a C l}_{2})

solution to analyze its effect on the average particle diameter

(D_{z})

, polymer structure and the intra- and intermolecular interactions in order to provide a responsive polymer network that can be used as a possible nanocarrier for drug delivery with several benefits. The results confirmed that the structural changes in the sensitive hydrogels are highly dependent on the corresponding critical solution temperature

(C S T)

of the carboxylic (–COOH) and amide (–CONH₂) functional groups and the influence of calcium ions

({C a}^{2 +})

on the formation or breaking of hydrogen bonds, as well as the decrease in electrostatic repulsions generated between the polymer chains contributing to a particle agglomeration phenomenon. The temperature leads to a re-arrangement of the polymer chains, affecting the viscoelastic properties of the hydrogels. In addition, the diffusion coefficients

(D)

of nanoparticles were evaluated, showing a closeness among with the morphology, shape, size and temperature, resulting in slower diffusions for larger particles size and, conversely, the diffusion in the medium increasing as the polymer size is reduced. Therefore, the hydrogels exhibited a remarkable response to pH and temperature variations in the environment. During this research, the functionality and behavior of the polymeric nanoparticles were observed under different analysis conditions, which revealed notable structural changes and further demonstrated the nanoparticles promising high potential for drug delivery applications. Hence, these results have sparked significant interest in various scientific, industrial and technological fields. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

15 pages, 6449 KiB

Open AccessArticle

Development and Characterization of Gelatin-Based Hydrogels Containing Triblock Copolymer and Phytic Acid

by Njomza Ajvazi, Ingrid Milošev, Romana Cerc Korošec, Peter Rodič and Bojan Božić

Gels 2024, 10(5), 294; https://doi.org/10.3390/gels10050294 - 25 Apr 2024

Viewed by 1600

Abstract

In recent research, significant interest has been directed towards gelatin-based hydrogels due to their affordable price, extensive availability, and biocompatibility, making them promising candidates for various biomedical applications. The development and characterization of novel hydrogels formed from varying ratios of gelatin, triblock copolymer [...] Read more.

In recent research, significant interest has been directed towards gelatin-based hydrogels due to their affordable price, extensive availability, and biocompatibility, making them promising candidates for various biomedical applications. The development and characterization of novel hydrogels formed from varying ratios of gelatin, triblock copolymer Pluronic F-127, and phytic acid have been presented. Swelling properties were examined at different pH levels. The morphology of hydrogels and their thermal properties were analyzed using scanning electron microscopy (SEM), thermogravimetric analysis (TG), and differential scanning calorimetry (DSC). Fourier-transform infrared (FTIR) analysis of the hydrogels was also performed. The introduction of phytic acid in the hydrogel plays a crucial role in enhancing the intermolecular interactions within gelatin-based hydrogels, contributing to a more stable, elastic, and robust network structure. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

26 pages, 5328 KiB

Open AccessEditor’s ChoiceArticle

Chitosan–Oxidized Pullulan Hydrogels Loaded with Essential Clove Oil: Synthesis, Characterization, Antioxidant and Antimicrobial Properties

by Dana Mihaela Suflet, Marieta Constantin, Irina Mihaela Pelin, Irina Popescu, Cristina M. Rimbu, Cristina Elena Horhogea and Gheorghe Fundueanu

Gels 2024, 10(4), 227; https://doi.org/10.3390/gels10040227 - 26 Mar 2024

Cited by 5 | Viewed by 2029

Abstract

Emulsion hydrogels are promising materials for encapsulating and stabilizing high amounts of hydrophobic essential oils in hydrophilic matrices. In this work, clove oil-loaded hydrogels (CS/OP-C) are synthesized by combining covalent and physical cross-linking approaches. First, clove oil (CO) was emulsified and stabilized in [...] Read more.

Emulsion hydrogels are promising materials for encapsulating and stabilizing high amounts of hydrophobic essential oils in hydrophilic matrices. In this work, clove oil-loaded hydrogels (CS/OP-C) are synthesized by combining covalent and physical cross-linking approaches. First, clove oil (CO) was emulsified and stabilized in a chitosan (CS) solution, which was further hardened by Schiff base covalent cross-linking with oxidized pullulan (OP). Second, the hydrogels were subjected to freeze–thaw cycles and, as a result, the clove oil was stabilized in physically cross-linked polymeric walls. Moreover, due to cryogelation, the obtained hydrogels exhibited sponge-like porous interconnected morphology (160–250 µm). By varying the clove oil content in the starting emulsion and the degree of cross-linking, the hydrogels displayed a high water retention capacity (swelling ratios between 1300 and 2000%), excellent elastic properties with fast shape recovery (20 s) after 70% compression, and controlled in vitro clove oil release in simulated skin conditions for 360 h. Furthermore, the prepared clove oil-loaded hydrogels had a strong scavenging activity of 83% and antibacterial and antifungal properties, showing a bacteriostatic effect after 48 and 72 h against S. aureus and E. coli. Our results recommend the new clove oil-embedded emulsion hydrogels as promising future materials for application as wound dressings. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Graphical abstract

12 pages, 2872 KiB

Open AccessArticle

Nanogels Based on N,N-Dimethylacrylamide and β-Cyclodextrin Triacrylate for Enhanced Solubility and Therapeutic Efficacy of Aripiprazole

by Siyka Stoilova, Dilyana Georgieva, Rositsa Mihaylova, Petar D. Petrov and Bistra Kostova

Gels 2024, 10(4), 217; https://doi.org/10.3390/gels10040217 - 22 Mar 2024

Cited by 1 | Viewed by 1697

Abstract

Aripiprazole (ARZ) is a medication used for the treatment of various diseases such as schizophrenia, bipolar disorder, major depressive disorder, autism, and Tourette’s syndrome. Despite its therapeutic benefits, ARZ is characterized by a poor water solubility which provoked the development of various delivery [...] Read more.

Aripiprazole (ARZ) is a medication used for the treatment of various diseases such as schizophrenia, bipolar disorder, major depressive disorder, autism, and Tourette’s syndrome. Despite its therapeutic benefits, ARZ is characterized by a poor water solubility which provoked the development of various delivery systems in order to enhance its solubility. In the present work, a nanoscale drug delivery system based on N,N-dimethylacrylamide (DMAA) and β-cyclodextrin triacrylate (β-CD-Ac₃) as potential aripiprazole delivery vehicles was developed. The nanogels were synthesized by free radical polymerization of DMAA in the presence of β-CD-Ac₃ as a crosslinking agent and then loaded with ARZ via host-guest inclusion complexation. The blank- and drug-loaded nanogels were evaluated using different methods. Fourier transform infrared (FTIR) spectroscopy was employed to confirm the incorporation of β-CD moieties into the polymer network. Dynamic light scattering (DLS) was used to study the size of the developed systems. The samples exhibited a monomodal particle size distribution and a relatively narrow dispersity index. The hydrodynamic diameter (D_h) of the gels varied between 107 and 129 nm, with a tendency for slightly larger particles as the β-CD-Ac₃ fraction increased. Loading the drug into the nanocarrier resulted in slightly larger particles than the blank gels, but their size was still in the nanoscopic range (166 to 169 nm). The release profiles in PBS were studied and a sustained release pattern with no significant burst effect was observed. A cytotoxicity assessment was also conducted to demonstrate the non-toxicity and biocompatibility of the studied polymers. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

17 pages, 4240 KiB

Open AccessEditor’s ChoiceArticle

Fabrication and Characterization of Quad-Component Bioinspired Hydrogels to Model Elevated Fibrin Levels in Central Nervous Tissue Scaffolds

by Ana M. Diaz-Lasprilla, Meagan McKee, Andrea C. Jimenez-Vergara, Swathisri Ravi, Devon Bellamy, Wendy Ortega, Cody O. Crosby, Jennifer Steele, Germán Plascencia-Villa, George Perry and Dany J. Munoz-Pinto

Gels 2024, 10(3), 203; https://doi.org/10.3390/gels10030203 - 17 Mar 2024

Viewed by 2061

Abstract

Multicomponent interpenetrating polymer network (mIPN) hydrogels are promising tissue-engineering scaffolds that could closely resemble key characteristics of native tissues. The mechanical and biochemical properties of mIPNs can be finely controlled to mimic key features of target cellular microenvironments, regulating cell-matrix interactions. In this [...] Read more.

Multicomponent interpenetrating polymer network (mIPN) hydrogels are promising tissue-engineering scaffolds that could closely resemble key characteristics of native tissues. The mechanical and biochemical properties of mIPNs can be finely controlled to mimic key features of target cellular microenvironments, regulating cell-matrix interactions. In this work, we fabricated hydrogels made of collagen type I (Col I), fibrin, hyaluronic acid (HA), and poly (ethylene glycol) diacrylate (PEGDA) using a network-by-network fabrication approach. With these mIPNs, we aimed to develop a biomaterial platform that supports the in vitro culture of human astrocytes and potentially serves to assess the effects of the abnormal deposition of fibrin in cortex tissue and simulate key aspects in the progression of neuroinflammation typically found in human pathologies such as Alzheimer’s disease (AD), Parkinson’s disease (PD), and tissue trauma. Our resulting hydrogels closely resembled the complex modulus of AD human brain cortex tissue (~7.35 kPa), promoting cell spreading while allowing for the modulation of fibrin and hyaluronic acid levels. The individual networks and their microarchitecture were evaluated using confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Human astrocytes were encapsulated in mIPNs, and negligible cytotoxicity was observed 24 h after the cell encapsulation. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Graphical abstract

14 pages, 4068 KiB

Open AccessArticle

Spray-Dried Chitosan Hydrogel Particles as a Potential Delivery System for Benzydamine Hydrochloride

by Sofia Milenkova, Rita Ambrus, Mahwash Mukhtar, Bissera Pilicheva and Maria Marudova

Gels 2024, 10(3), 189; https://doi.org/10.3390/gels10030189 - 8 Mar 2024

Cited by 2 | Viewed by 1928

Abstract

Chitosan, being a biocompatible and mucoadhesive polysaccharide, is one of the most preferred hydrogel-forming materials for drug delivery. The objectives of the present study are to obtain spray-dried microparticles based on low-molecular-weight chitosan and study their potential application as cargo systems for the [...] Read more.

Chitosan, being a biocompatible and mucoadhesive polysaccharide, is one of the most preferred hydrogel-forming materials for drug delivery. The objectives of the present study are to obtain spray-dried microparticles based on low-molecular-weight chitosan and study their potential application as cargo systems for the orally active drug benzydamine hydrochloride. Three types of particles are obtained: raw chitosan particles (at three different concentrations), cross-linked with sodium tripolyphosphate (NaTPP) particles (at three different chitosan:NaTPP ratios), and particles coated with mannitol (at three different chitosan:mannitol ratios), all of them in the size range between 1 and 10 µm. Based on the loading efficiency and the yields of the formulated hydrogel particles, one model of each type is chosen for further investigation of the effect of the cross-linker or the excipient on the properties of the gel structures. The morphology of both empty and benzydamine hydrochloride-loaded chitosan particles was examined by scanning electron microscopy, and it was quite regular and spherical. Interactions and composition in the samples are investigated by Fourier-transformed infrared spectroscopy. The thermal stability and phase state of the drug and drug-containing polymer matrixes were tested by differential scanning calorimetry and X-ray powdered diffraction, revealing that the drug underwent a phase transition. A drug release kinetics study of the chosen gel-based structures in simulated saliva buffer (pH = 6.8) and mathematical modeling of the process were performed, indicating the Weibull model as the most appropriate one. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

22 pages, 7591 KiB

Open AccessArticle

Preparation and Mechano-Functional Characterization of PEGylated Fibrin Hydrogels: Impact of Thrombin Concentration

by Clara F. López-León, Ramon Planet and Jordi Soriano

Gels 2024, 10(2), 116; https://doi.org/10.3390/gels10020116 - 1 Feb 2024

Cited by 1 | Viewed by 1583

Abstract

Three-dimensional (3D) neuronal cultures grown in hydrogels are promising platforms to design brain-like neuronal networks in vitro. However, the optimal properties of such cultures must be tuned to ensure a hydrogel matrix sufficiently porous to promote healthy development but also sufficiently rigid for [...] Read more.

Three-dimensional (3D) neuronal cultures grown in hydrogels are promising platforms to design brain-like neuronal networks in vitro. However, the optimal properties of such cultures must be tuned to ensure a hydrogel matrix sufficiently porous to promote healthy development but also sufficiently rigid for structural support. Such an optimization is difficult since it implies the exploration of different hydrogel compositions and, at the same time, a functional analysis to validate neuronal culture viability. To advance in this quest, here we present a combination of a rheological protocol and a network-based functional analysis to investigate PEGylated fibrin hydrogel networks with gradually higher stiffness, achieved by increasing the concentration of thrombin. We observed that moderate thrombin concentrations of 10% and 25% in volume shaped healthy networks, although the functional traits depended on the hydrogel stiffness, which was much higher for the latter concentration. Thrombin concentrations of 65% or higher led to networks that did not survive. Our results illustrate the difficulties and limitations in preparing 3D neuronal networks, and stress the importance of combining a mechano-structural characterization of a biomaterial with a functional one. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Graphical abstract

Review

Jump to: Research

35 pages, 3174 KiB

Open AccessReview

Advancements and Challenges in Self-Healing Hydrogels for Wound Care

by Hossein Omidian, Renae L. Wilson and Erma J. Gill

Gels 2024, 10(4), 241; https://doi.org/10.3390/gels10040241 - 1 Apr 2024

Cited by 4 | Viewed by 3461

Abstract

This manuscript explores self-healing hydrogels as innovative solutions for diverse wound management challenges. Addressing antibiotic resistance and tailored wound care, these hydrogels exhibit promising outcomes, including accelerated wound closure and tissue regeneration. Advancements in multifunctional hydrogels with controlled drug release, antimicrobial properties, and [...] Read more.

This manuscript explores self-healing hydrogels as innovative solutions for diverse wound management challenges. Addressing antibiotic resistance and tailored wound care, these hydrogels exhibit promising outcomes, including accelerated wound closure and tissue regeneration. Advancements in multifunctional hydrogels with controlled drug release, antimicrobial properties, and real-time wound assessment capabilities signal a significant leap toward patient-centered treatments. However, challenges such as scalability, long-term safety evaluation, and variability in clinical outcomes persist. Future directions emphasize personalized medicine, manufacturing innovation, rigorous evaluation through clinical trials, and interdisciplinary collaboration. This manuscript features the ongoing pursuit of effective, adaptable, and comprehensive wound care solutions to transform medical treatments and improve patient outcomes. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

29 pages, 2617 KiB

Open AccessEditor’s ChoiceReview

Advancements in Cellulose-Based Superabsorbent Hydrogels: Sustainable Solutions across Industries

by Hossein Omidian, Arnavaz Akhzarmehr and Sumana Dey Chowdhury

Gels 2024, 10(3), 174; https://doi.org/10.3390/gels10030174 - 29 Feb 2024

Cited by 7 | Viewed by 3815

Abstract

The development of superabsorbent hydrogels is experiencing a transformative era across industries. While traditional synthetic hydrogels have found broad utility, their non-biodegradable nature has raised environmental concerns, driving the search for eco-friendlier alternatives. Cellulose-based superabsorbents, derived from sustainable sources, are gaining prominence. Innovations [...] Read more.

The development of superabsorbent hydrogels is experiencing a transformative era across industries. While traditional synthetic hydrogels have found broad utility, their non-biodegradable nature has raised environmental concerns, driving the search for eco-friendlier alternatives. Cellulose-based superabsorbents, derived from sustainable sources, are gaining prominence. Innovations include biodegradable polymer hydrogels, natural cellulose-chitosan variants, and cassava starch-based alternatives. These materials are reshaping agriculture by enhancing soil fertility and water retention, serving as potent hemostatic agents in medicine, contributing to pollution control, and providing eco-friendly construction materials. Cellulose-based hydrogels also offer promise in drug delivery and hygiene products. Advanced characterization techniques aid in optimizing their properties, while the shift towards circular economy practices further highlights sustainability. This manuscript provides a comprehensive overview of these advancements, highlighting their diverse applications and environmental benefits. Full article

(This article belongs to the Special Issue Gel-Based Materials: Preparations and Characterization (2nd Edition))

► Show Figures

Figure 1

Journal Menu

Journal Browser

Gel-Based Materials: Preparations and Characterization (2nd Edition)

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Benefits of Publishing in a Special Issue

Related Special Issue

Published Papers (13 papers)

Research

Review

Further Information

Guidelines

MDPI Initiatives

Follow MDPI