Photonics

13 pages, 4053 KiB

Open AccessArticle

In Situ Preparation of Thin-Film Q-Switches Based on Vanadium Dioxide for Pulsed Fiber Lasers

by Dmitriy P. Sudas, Sergei M. Popov and Petr I. Kuznetsov

Photonics 2025, 12(2), 133; https://doi.org/10.3390/photonics12020133 - 3 Feb 2025

Viewed by 156

In the presented work, erbium fiber lasers operating in the pulsed mode with a nonlinear element containing a vanadium oxide saturable absorber are demonstrated. The structure of the saturable absorber is based on a segment of thinned silica fiber coated with a thin-film [...] Read more.

In the presented work, erbium fiber lasers operating in the pulsed mode with a nonlinear element containing a vanadium oxide saturable absorber are demonstrated. The structure of the saturable absorber is based on a segment of thinned silica fiber coated with a thin-film vanadium oxide by the method of metalorganic chemical vapor deposition. A fiber laser scheme is demonstrated that allows controlling the transmission of the internal cavity of the resonator during laser generation and deposition of a thin film. We have demonstrated a method for obtaining and annealing nanocoatings with laser generation control. We controlled the laser output parameters directly during the synthesis of the saturable absorber material. Vanadium oxides obtained in the work demonstrated the Mott–Paierls phase transition practically at room temperature. In this work, the optical characteristics of the output radiation of a fiber laser with a saturable absorber were measured. At temperatures above 70 °C, the coatings demonstrate a passive Q-switch with a repetition rate of 38 kHz and a pulse duration of 3.8 μs. At temperatures below the phase transition, a short-term mode-locking mode occurs. The transmission jump at a wavelength of about 1350 nm during structural rearrangement was 24%. For comparison, VO₂ nanopowder in a polydimethylsiloxane elastomer matrix was used as a saturable absorber material. The nanopowder modulator made it possible to obtain pulses with a frequency of 27 kHz and a duration of about 7.2 μs. Full article

(This article belongs to the Special Issue Cutting-Edge Developments in Fiber Laser)

► Show Figures

Figure 1

15 pages, 1969 KiB

Open AccessArticle

A Conceptual Study of Rapidly Reconfigurable and Scalable Bidirectional Optical Neural Networks Leveraging a Smart Pixel Light Modulator

by Young-Gu Ju

Photonics 2025, 12(2), 132; https://doi.org/10.3390/photonics12020132 - 2 Feb 2025

Viewed by 283

Abstract

We explore the integration of smart pixel light modulators (SPLMs) into bidirectional optical neural networks (BONNs), highlighting their advantages over traditional spatial light modulators (SLMs). SPLMs enhance BONN performance by enabling faster light modulation in both directions, significantly increasing the refresh rate of [...] Read more.

We explore the integration of smart pixel light modulators (SPLMs) into bidirectional optical neural networks (BONNs), highlighting their advantages over traditional spatial light modulators (SLMs). SPLMs enhance BONN performance by enabling faster light modulation in both directions, significantly increasing the refresh rate of neural network weights to hundreds of megahertz, thus facilitating the practical implementation of the backpropagation algorithm and two-mirror-like BONN structures. The architecture of an SPLM-based BONN (SPBONN) features bidirectional modulation, simplifying hardware with electrical fan-in and fan-out. An SPBONN with an array size of 96 × 96 can achieve high throughput, up to 4.3 × 10¹⁶ MAC/s with 10 layers. Energy assessments showed that the SPLM array, despite its higher power consumption compared to the SLM array, is manageable via effective heat dissipation. Smart pixels with programmable memory in the SPBONN provide a cost-effective solution for expanding network node size and overcoming scalability limitations without the need for additional hardware. Full article

(This article belongs to the Special Issue Advances in Free-Space Optical Communications)

11 pages, 4045 KiB

Open AccessArticle

Sagnac Interference-Based Contact-Type Fiber-Optic Vibration Sensor

by Hongmei Li, Longhuang Tang, Lijie Zhang, Wenjuan Huang, Rong Cao, Cheng Huang, Xiaobo Hu, Yifei Sun and Jia Shi

Photonics 2025, 12(2), 131; https://doi.org/10.3390/photonics12020131 - 2 Feb 2025

Viewed by 347

Abstract

The observation and evaluation of vibration signals is crucial for enhancing engineering quality and ensuring the safe operation of equipment. This paper proposes a fiber-optic vibration sensor based on the Sagnac interference principle. The polarization-maintaining fiber (PMF) is spliced between two single mode [...] Read more.

The observation and evaluation of vibration signals is crucial for enhancing engineering quality and ensuring the safe operation of equipment. This paper proposes a fiber-optic vibration sensor based on the Sagnac interference principle. The polarization-maintaining fiber (PMF) is spliced between two single mode fibers (SMFs) to form the SMF-PMF-SMF (SPS) fiber structure. The Sagnac interferometer consists of an SPS fiber structure connected to a 3 dB coupler. Due to the principle of the elastic-optical effect, the interferometric spectrum of the PMF-based Sagnac interferometric structure changes when the PMF is subjected to stress, enabling vibration to be measured. The experimental results show that the relative measurement error of the fiber-optic vibration sensor for healthy and faulty bearings is less than 1.8%, which verifies the effectiveness and accuracy of the sensor. The sensor offers benefits of excellent anti-vibration fatigue characteristics, simple production, small size, light weight, and has a wide range of applications in mechanical engineering, fault detection, safety and security, and other fields. Full article

(This article belongs to the Special Issue Emerging Trends in Optical Fiber Sensors and Sensing Techniques)

► Show Figures

Figure 1

10 pages, 519 KiB

Open AccessArticle

High-Peak-Power Sub-Nanosecond Laser Pulse Sources Based on Hetero-Integrated “Heterothyristor–Laser Diode” Vertical Stack

by Sergey Slipchenko, Aleksander Podoskin, Ilia Shushkanov, Artem Rizaev, Matvey Kondratov, Viktor Shamakhov, Vladimir Kapitonov, Kirill Bakhvalov, Artem Grishin, Timur Bagaev, Maxim Ladugin, Aleksander Marmalyuk, Vladimir Simakov and Nikita Pikhtin

Photonics 2025, 12(2), 130; https://doi.org/10.3390/photonics12020130 - 1 Feb 2025

Viewed by 333

Abstract

Compact high-power sub-nanosecond laser pulse sources with a wavelength of 940 nm are developed and studied. A design for laser pulse sources based on a vertical stack is proposed, which includes a semiconductor laser chip and a current switch chip. To create a [...] Read more.

Compact high-power sub-nanosecond laser pulse sources with a wavelength of 940 nm are developed and studied. A design for laser pulse sources based on a vertical stack is proposed, which includes a semiconductor laser chip and a current switch chip. To create a compact high-speed current switch, a three-electrode heterothyristor is developed. It is found that the use of heterothyristor-based current switches allows the creation of a low-loss pump current circuit, generating short current pulses and operating the semiconductor laser in gain-switching mode. For the semiconductor laser chip, an asymmetric semiconductor heterostructure with a quantum-well active region is designed. The design of the emitting aperture of the laser chip is optimized to improve the operating characteristics of the laser beam when generating sub-ns optical pulses. It is shown that the transition to a monolithic emitting aperture design reduces the laser pulse turn-on spatial inhomogeneity, which is 90 ps over the entire range of optical powers studied. It is also demonstrated that by increasing the emitting aperture width to 400 μm, laser pulses with a peak power of 39.5 W and a pulse width at full width at half maximum (FWHM) of 120 ps can be generated. Full article

(This article belongs to the Section Lasers, Light Sources and Sensors)

9 pages, 1179 KiB

Open AccessArticle

Continuous-Wave Room-Temperature External Cavity Quantum Cascade Lasers Operating at λ~8.5 μm

by Zixian Wang, Yuzhe Lin, Yuan Ma, Chenyang Wan, Fengxin Dong, Xuyan Zhou, Jinchuan Zhang, Fengqi Liu and Wanhua Zheng

Photonics 2025, 12(2), 129; https://doi.org/10.3390/photonics12020129 - 31 Jan 2025

Viewed by 269

Abstract

External cavity quantum cascade lasers (EC-QCLs) utilizing the Littrow configuration and operating at an approximate wavelength of 8.5 μm have been successfully demonstrated in continuous wave operations at room temperature. Our work provides ideas and experimental support for the optimization of the EC-QCL [...] Read more.

External cavity quantum cascade lasers (EC-QCLs) utilizing the Littrow configuration and operating at an approximate wavelength of 8.5 μm have been successfully demonstrated in continuous wave operations at room temperature. Our work provides ideas and experimental support for the optimization of the EC-QCL which indicate optimal EC-QCL performance with an external cavity length of 25 cm and investigates the impact of various parameters, including injection current and temperature on the performance of the EC-QCL. In the absence of anti-reflection (AR) coating, the tuning range at 25 °C extends up to 103.3 cm⁻¹, while the maximum side mode suppression ratio (SMSR) reaches 30.8 dB, accompanied by a full width half maximum linewidth (FWHM) of 0.76 nm. Full article

(This article belongs to the Special Issue The Three-Decade Journey of Quantum Cascade Lasers)

11 pages, 1534 KiB

Open AccessCommunication

SVM-Based Optical Detection of Retinal Ganglion Cell Apoptosis

by Mukhit Kulmaganbetov, Ryan Bevan, Andrew Want, Nantheera Anantrasirichai, Alin Achim, Julie Albon and James Morgan

Photonics 2025, 12(2), 128; https://doi.org/10.3390/photonics12020128 - 31 Jan 2025

Viewed by 249

Abstract

Background: Retinal ganglion cell (RGC) loss is crucial in eye diseases like glaucoma. Axon damage and dendritic degeneration precede cell death, detectable within optical coherence tomography (OCT) resolution, indicating their correlation with neuronal degeneration. The purpose of this study is to evaluate [...] Read more.

Background: Retinal ganglion cell (RGC) loss is crucial in eye diseases like glaucoma. Axon damage and dendritic degeneration precede cell death, detectable within optical coherence tomography (OCT) resolution, indicating their correlation with neuronal degeneration. The purpose of this study is to evaluate the optical changes of early retinal degeneration. Methods: The detection of optical changes in the axotomised retinal explants was completed in six C57BL/6J mice. OCT images were acquired up to 120 min from enucleation. A grey-level co-occurrence-based texture analysis was performed on the inner plexiform layer (IPL) to monitor changes in the optical speckles using a principal component analysis (PCA) and a support vector machine (SVM). In parallel tests, retinal transparency was confirmed by a comparison of the modulation transfer functions (MTFs) at 0 and 120 min. Results: Quantitative confirmation by analysis of the MTFs confirmed the non-degradation of optical transparency during the imaging period: MTF (fx) = 0.267 ± 0.02. Textural features in the IPL could discriminate between the optical signals of RGC degeneration. The mean accuracy of the SVM classification was 86.3%; discrimination was not enhanced by the combination of the SVM and PCA (81.9%). Conclusions: Optical changes in the IPL can be detected using OCT following RGC axotomy. High-resolution OCT can provide an index of retinal neuronal integrity and its degeneration. Full article

(This article belongs to the Special Issue Biomedical Optics：Imaging, Sensing and Therapy)

11 pages, 2273 KiB

Open AccessArticle

Demonstration of Quantum Polarized Microscopy Using an Entangled-Photon Source

by Mousume Samad, Maki Shimizu and Yasuto Hijikata

Photonics 2025, 12(2), 127; https://doi.org/10.3390/photonics12020127 - 31 Jan 2025

Viewed by 403

Abstract

With the advancement of non-classical light sources such as single-photon and entangled-photon sources, innovative microscopy based on quantum principles has been proposed for traditional microscopy. This paper introduces the experimental demonstration of a quantum polarization microscopic technique that incorporates a quantum-entangled photon source. [...] Read more.

With the advancement of non-classical light sources such as single-photon and entangled-photon sources, innovative microscopy based on quantum principles has been proposed for traditional microscopy. This paper introduces the experimental demonstration of a quantum polarization microscopic technique that incorporates a quantum-entangled photon source. Although the point that employs the variation in polarization angle due to reflection or transmission at the sample is similar to classical polarization microscopy, the method for constructing the image contrast is significantly different. The image contrast is constructed by the coincidence count of signal and idler photons. In the case that the coincidence count is recorded from both the signal and idler photons, the photon statistics resemble a thermal state, similar to the blackbody radiation, but with a significantly higher peak intensity in the second-order autocorrelation function at zero delay that is derived from the coincidence count, while, when the coincidence count is taken from either the signal or idler photon only, although the photon state exhibits a thermal state again, the photon statistics become more dispersive and result in a lower peak intensity of the autocorrelation function. These different thermal states can be switched by slightly changing the photon polarization, which is suddenly aroused within a narrow range of the analyzer angle. The autocorrelation function g²(0) at the thermal state exhibits a sensitivity that is three times higher compared to the classical coincidence count rate, and this concept can be effectively utilized to enhance the contrast of the image. One of the key achievements of our proposed method is ensuring a low power of illumination (in the order of Pico-joules) for constructing the image. In addition, the robustness without any precise setup is also favorable for practical use. This polarization microscopic technique can provide a superior imaging technique compared to the classical method, opening a new frontier for research in material sciences, biology, and other fields requiring high-resolution imaging. Full article

(This article belongs to the Special Issue Photonics: 10th Anniversary)

► Show Figures

Figure 1

7 pages, 1822 KiB

Open AccessCommunication

Grating Pair Wavepacket Shaper for Crafting Spatiotemporal Optical Vortices with Arbitrary Tilt Angles

by Jordan Adams and Andy Chong

Photonics 2025, 12(2), 126; https://doi.org/10.3390/photonics12020126 - 31 Jan 2025

Viewed by 248

Abstract

Spatiotemporal optical vortices with arbitrary tilt angles can be generated by adjusting spatial chirp and beam size at a phase modulation plane in a pulse shaper setup. A grating pair setup is proposed to generate variable spatial chirp independent of the beam profile. [...] Read more.

Spatiotemporal optical vortices with arbitrary tilt angles can be generated by adjusting spatial chirp and beam size at a phase modulation plane in a pulse shaper setup. A grating pair setup is proposed to generate variable spatial chirp independent of the beam profile. The initial dispersion of the pulse allows for the independent control of the vortex orientation. By adjusting the beam size, spatial chirp, and initial dispersion, arbitrary vortex orientation across all the possible angles can be achieved. The ability to achieve arbitrary vortex orientations at long propagation distances could offer significant advantages for long-distance communication applications. Full article

(This article belongs to the Special Issue Progress in OAM Beams: Recent Innovations and Future Perspectives)

► Show Figures

Figure 1

21 pages, 15250 KiB

Open AccessReview

Plasmonic Vortices: A Promising Tool Utilizing Plasmonic Orbital Angular Momentum

by Zhi Gao, Dmitri V. Voronine and Alexei V. Sokolov

Photonics 2025, 12(2), 125; https://doi.org/10.3390/photonics12020125 - 31 Jan 2025

Viewed by 361

Abstract

An optical vortex (OV) beam is an important type of spatially structured beam. However, the diffraction limit for light with orbital angular momentum (OAM) remains a challenge for certain applications. Surface plasmon polaritons (SPPs) can confine light to nanoscale dimensions and enhance light–matter [...] Read more.

An optical vortex (OV) beam is an important type of spatially structured beam. However, the diffraction limit for light with orbital angular momentum (OAM) remains a challenge for certain applications. Surface plasmon polaritons (SPPs) can confine light to nanoscale dimensions and enhance light–matter interactions. Over the past two decades, researchers have begun to explore the imparting of OAM onto SPPs to generate plasmonic vortices (PVs). Since the discovery of PVs, significant efforts have been made in this field, leading to considerable progress. This article reviews these studies in three key areas: (a) the generation and manipulation of PVs, (b) the characterization of PVs, and (c) the application of PVs. We believe that PVs represent a promising tool utilizing plasmonic OAM for both fundamental research and practical applications and hold great potential for the future with continued dedicated efforts. Full article

(This article belongs to the Special Issue Ultrafast Pulse Shaping Techniques: From Temporal to Spatiotemporal Control)

► Show Figures

Figure 1

8 pages, 2635 KiB

Open AccessArticle

Determination of the Effective Lifetime of a Spinor Bose–Einstein Condensate

by Xin Wang, Yong Qin, Jun Jian, Wenliang Liu, Jizhou Wu, Yuqing Li, Vladimir Sovkov and Jie Ma

Photonics 2025, 12(2), 124; https://doi.org/10.3390/photonics12020124 - 30 Jan 2025

Viewed by 407

Abstract

The effective lifetime of ultra-cold atoms in specific quantum states plays a crucial role in studying interaction parameters within quantum systems. Measuring the effective lifetime of various quantum states within ultra-cold atoms is a fundamental task in quantum operations. In this paper, the [...] Read more.

The effective lifetime of ultra-cold atoms in specific quantum states plays a crucial role in studying interaction parameters within quantum systems. Measuring the effective lifetime of various quantum states within ultra-cold atoms is a fundamental task in quantum operations. In this paper, the effective lifetimes of the excited electronic states

|F = 2, m_{F} = - 2⟩

,

|F = 2, m_{F} = - 1⟩

, and

|F = 2, m_{F} = 0⟩

for a sodium atomic Bose–Einstein condensate (BEC) are investigated in both the optical dipole trap (ODT) and one-dimensional optical lattice. Through the analysis of experimental data, we demonstrate the significant advantage of lattice loading over the optical dipole trap in terms of atomic lifetimes. The results provide crucial insights into the temporal scales relevant for investigating the evolution of boson gases in optical lattices, facilitating the realization of quantum simulations pertaining to unique quantum phases, and providing an important experimental basis for the research of non-equilibrium dynamics between different spin states. Full article

(This article belongs to the Section Lasers, Light Sources and Sensors)

12 pages, 725 KiB

Open AccessArticle

Near-Field Enhancement in SPASER Nanostructures for High-Efficiency Energy Conversion

by Amine Jaouadi, Ahmed Mahjoub and Montacer Dridi

Photonics 2025, 12(2), 123; https://doi.org/10.3390/photonics12020123 - 29 Jan 2025

Viewed by 346

Abstract

We present in this study a theoretical investigation of the near-field enhancement phenomenon within nanostructures, which have garnered recent attention due to their potential applications in sensing, imaging, and energy harvesting. The analysis reveals a significant intensification of electromagnetic fields proximal to periodically [...] Read more.

We present in this study a theoretical investigation of the near-field enhancement phenomenon within nanostructures, which have garnered recent attention due to their potential applications in sensing, imaging, and energy harvesting. The analysis reveals a significant intensification of electromagnetic fields proximal to periodically arranged arrays of gold nanoparticles sustaining a highly lossy mode. In addition to the existence of a localized surface plasmon (LSP) mode exhibiting suboptimal quality, our investigation unveils intricate aspects of near-field enhancement closely correlated to the dynamics of lasing mechanisms. Notably, our investigation is focused on elucidating the augmentation’s behavior across varying pumping energies. The achieved enhancement surpasses two orders of magnitude compared to the passive counterparts. We introduce a description of the energy conversion rate specific to the SPASER configuration. The conceptualized SPASER reveals a significant promise. It showcases energy conversion efficiency up to 80%, emphasizing the SPASER’s potential as a highly effective nano-scale energy source. Full article

(This article belongs to the Special Issue Optical Fiber Lasers and Laser Technology)

14 pages, 6634 KiB

Open AccessArticle

Method of Tissue Differentiation Based on Changes in Tissue Optical Properties Under Mechanical Stress Estimated with Optical Coherence Tomography

by Evgeny P. Sherstnev, Alexander A. Moiseev, Aleksander A. Sovetsky, Pavel A. Shilyagin, Sergey Y. Ksenofontov and Grigory V. Gelikonov

Photonics 2025, 12(2), 122; https://doi.org/10.3390/photonics12020122 - 29 Jan 2025

Viewed by 442

Abstract

This study highlights the possibility of contrasting the differences in tissues’ mechanical properties from Optical Coherence Tomography (OCT) data without maintaining phase stability during OCT data acquisition. The proposed method is based on the rate of attenuation coefficient changes under the mechanical pressure [...] Read more.

This study highlights the possibility of contrasting the differences in tissues’ mechanical properties from Optical Coherence Tomography (OCT) data without maintaining phase stability during OCT data acquisition. The proposed method is based on the rate of attenuation coefficient changes under the mechanical pressure evaluation of the OCT data. It was shown, both on the calibrated synthetic and ex vivo biological samples, that the rate of attenuation coefficient changes observed corresponds to the sample’s mechanical properties and could be used to characterize the sample and distinguish it from other samples even if their optical properties before the pressure application are similar. This opens up the possibility to use an in vivo OCT-based system that can contrast mechanical properties without ensuring phase stability. Full article

(This article belongs to the Special Issue Advanced Technologies in Biophotonics and Medical Physics)

► Show Figures

Figure 1

11 pages, 6125 KiB

Open AccessCommunication

Localized Effects in Graphene Oxide Systems: A Pathway to Hyperbolic Metamaterials

by Grazia Giuseppina Politano

Photonics 2025, 12(2), 121; https://doi.org/10.3390/photonics12020121 - 29 Jan 2025

Viewed by 430

Abstract

Graphene oxide (GO) has emerged as a carbon-based nanomaterial providing a different pathway to graphene. One of its most notable features is the ability to partially reduce it, resulting in graphene-like sheets through the elimination of oxygen-including functional groups. In this paper, the [...] Read more.

Graphene oxide (GO) has emerged as a carbon-based nanomaterial providing a different pathway to graphene. One of its most notable features is the ability to partially reduce it, resulting in graphene-like sheets through the elimination of oxygen-including functional groups. In this paper, the effect of localized interactions in an Ag/GO/Au multilayer system was studied to explore its potential for photonic applications. GO was dip-coated onto magnetron-sputtered silver, followed by the deposition of a thin gold film to form an Ag/GO/Au structure. Micro-Raman Spectroscopy, SEM and Variable Angle Ellipsometry (VASE) measurements were performed on the Ag/GO/Au structure. An interesting behavior of the GO deposited on magnetron-sputtered silver with the formation of Ag nanostructures on top of the GO layer is reported. In addition to typical GO bands, Micro-Raman analysis reveals peaks such as the 1478 cm⁻¹ band, indicating a transition from sp³ to sp² hybridization, confirming the partial reduction of GO. Additionally, calculations based on effective medium theory (EMT) highlight the potential of Ag/GO structures in hyperbolic metamaterials for photonics. The medium exhibits dielectric behavior up to 323 nm, transitions to type I HMM between 323 and 400 nm and undergoes an Epsilon Near Zero and Pole (ENZP) transition at 400 nm, followed by type II HMM behavior. Full article

(This article belongs to the Special Issue Photonics Metamaterials: Processing and Applications)

► Show Figures

Figure 1

30 pages, 2229 KiB

Open AccessReview

Optoelectronic Oscillators: Progress from Classical Designs to Integrated Systems

by Qidi Liu, Jiuchang Peng and Juanjuan Yan

Photonics 2025, 12(2), 120; https://doi.org/10.3390/photonics12020120 - 29 Jan 2025

Viewed by 330

Abstract

Optoelectronic oscillators (OEOs) have emerged as indispensable tools for generating low-phase-noise microwave and millimeter-wave signals, which are critical for a variety of high-performance applications. These include radar systems, satellite links, electronic warfare, and advanced instrumentation. The ability of OEOs to produce signals with [...] Read more.

Optoelectronic oscillators (OEOs) have emerged as indispensable tools for generating low-phase-noise microwave and millimeter-wave signals, which are critical for a variety of high-performance applications. These include radar systems, satellite links, electronic warfare, and advanced instrumentation. The ability of OEOs to produce signals with exceptionally low phase noise makes them ideal for scenarios demanding high signal purity and stability. In radar systems, low-phase-noise signals enhance target detection accuracy and resolution, while, in communication networks, such signals enable higher data throughput and improved signal integrity over extended distances. Furthermore, OEOs play a pivotal role in precision instrumentation, where even minor noise can compromise the performance of sensitive equipment. This review examines the progress in OEO technology, transitioning from classical designs relying on long optical fiber delay lines to modern integrated systems that leverage photonic integration for compact, efficient, and tunable solutions. Key advancements, including classical setups, hybrid designs, and integrated configurations, are discussed, with a focus on their performance improvements in phase noise, side-mode suppression ratio (SMSR), and frequency tunability. A 20-GHz oscillation with an SMSR as high as 70 dB has been achieved using a classical dual-loop configuration. A 9.867-GHz frequency with a phase noise of −142.5 dBc/Hz @ 10 kHz offset has also been generated in a parity–time-symmetric OEO. Additionally, integrated OEOs based on silicon photonic microring resonators have achieved an ultra-wideband tunable frequency from 3 GHz to 42.5 GHz, with phase noise as low as −93 dBc/Hz at a 10 kHz offset. The challenges in achieving fully integrated OEOs, particularly concerning the stability and phase noise at higher frequencies, are also explored. This paper provides a comprehensive overview of the state of the art in OEO technology, highlighting future directions and potential applications. Full article

(This article belongs to the Special Issue Application and Development of Optoelectronic Oscillators (OEOs) in Microwave Photonics)

13 pages, 12684 KiB

Open AccessArticle

Creation of Bessel–Gaussian Beams from Necklace Beams via Second-Harmonic Generation

by Nikolay Dimitrov, Kiril Hristov, Maya Zhekova and Alexander Dreischuh

Photonics 2025, 12(2), 119; https://doi.org/10.3390/photonics12020119 - 28 Jan 2025

Viewed by 319

Abstract

The interest in (quasi-)nondiffracting beams is rooted in applications spanning from secure sharing cryptographic keys real-world free-space optical communications and high-order harmonic generation to high-aspect-ratio nanochannel machining, photopolymerization, and nanopatterning, just to mention a few. In this work, we explore the robustness of [...] Read more.

The interest in (quasi-)nondiffracting beams is rooted in applications spanning from secure sharing cryptographic keys real-world free-space optical communications and high-order harmonic generation to high-aspect-ratio nanochannel machining, photopolymerization, and nanopatterning, just to mention a few. In this work, we explore the robustness of the approach for generating Bessel–Gaussian beams by Fourier transforming ring-shaped beams and push the limits further. Here, instead of ring-shaped beams, we use strongly azimuthally modulated necklace beams. Necklace structures are generated by interference of OV beams that carry equal topological charges of opposite signs. In order to effectively account for the azimuthal

π

-phase jumps in the necklace beams, we first generate their second harmonic, thereafter focusing (i.e., Fourier transforming) them with a thin lens. In this way, we successfully create Bessel–Gaussian beams in the second harmonic of a pump beam with strong azimuthal modulation. The experimental data presented are in good agreement with the developed analytical model. Full article

(This article belongs to the Special Issue Advances in Structured Light: Propagation, Scattering, and Applications)

17 pages, 3014 KiB

Open AccessArticle

Design and Application of Laser Polarization Underwater Detection Equipment

by Yong Zhu, Fangxing Zong, Chao Dong, Qiang Fu, Xiansong Gu, Qingyi He, Jianhua Liu, Li Zheng, Geng Dong, Haili Zhao and Jin Duan

Photonics 2025, 12(2), 118; https://doi.org/10.3390/photonics12020118 - 28 Jan 2025

Viewed by 338

Abstract

With the increasing demand for precise identification of underwater targets, the development of advanced underwater detection technologies has become a pivotal area of research. This study presents the design and implementation of a laser-based underwater detection system that leverages polarization characteristics to significantly [...] Read more.

With the increasing demand for precise identification of underwater targets, the development of advanced underwater detection technologies has become a pivotal area of research. This study presents the design and implementation of a laser-based underwater detection system that leverages polarization characteristics to significantly enhance detection accuracy and target identification capabilities in complex aquatic environments. A key innovation of this research lies in the application of a dual-frequency modulation technology using a 532 nm pulsed laser. By modulating the high-frequency characteristics of the laser, this technique effectively suppresses backscattering interference within the water medium, improves the efficiency of target signal extraction, and exhibits exceptional performance, particularly in long-range detection and highly turbid water conditions. This paper elucidates the principles of underwater laser detection and polarization measurement, outlines the design of an integrated optical and mechanical system for laser transmission and reception, and introduces an optimized signal processing methodology. Experimental results demonstrate that the proposed system can reliably distinguish targets composed of different materials while maintaining high detection accuracy across a range of challenging environmental conditions. A comparative analysis further highlights the system’s significant advantages over traditional technologies, including enhanced noise suppression and greater detection depth. These findings establish a solid foundation for advancing underwater detection technologies and broadening their practical applications. Full article

► Show Figures

Figure 1

9 pages, 2820 KiB

Open AccessArticle

A Fast Rearrangement Method for Defect-Free Atom Arrays

by Yuqing Zhang, Zeyan Zhang, Guoqing Zhang, Zhehua Zhang, Yanpu Chen, Yuqing Li, Wenliang Liu, Jizhou Wu, Vladimir Sovkov and Jie Ma

Photonics 2025, 12(2), 117; https://doi.org/10.3390/photonics12020117 - 28 Jan 2025

Viewed by 388

Abstract

Defect-free atom arrays provide new possibilities for exploring exotic quantum phenomena and realizing quantum computing. However, quickly and efficiently preparing defect-free atom arrays poses challenges. This paper proposes an innovative parallel rearrangement method, namely the parallel compression filling algorithm (PCFA), wherein multiple movable [...] Read more.

Defect-free atom arrays provide new possibilities for exploring exotic quantum phenomena and realizing quantum computing. However, quickly and efficiently preparing defect-free atom arrays poses challenges. This paper proposes an innovative parallel rearrangement method, namely the parallel compression filling algorithm (PCFA), wherein multiple movable optical tweezers operate simultaneously. By limiting the shape of the initial loading, the method reduces movement complexity. The simulation comparisons show that this algorithm is more efficient in preparing defect-free atom arrays and can also be applied to the generation of other periodic structure arrays. The simulation results show that, in most cases, preparing a defect-free array of 400 atoms requires no more than 30 steps. Full article

18 pages, 14990 KiB

Open AccessArticle

Design of a Freeform Surface Optical Detection System with a Square Aperture

by Hongkai Zhao and Xianglong Mao

Photonics 2025, 12(2), 116; https://doi.org/10.3390/photonics12020116 - 28 Jan 2025

Viewed by 391

Abstract

To meet the demands for heightened detection sensitivity in satellite-based space target detection systems, we introduce an innovative square aperture diaphragm system utilizing freeform surfaces for detecting targets in the visible light spectrum. Characterized by a 40 mm × 40 mm square entrance [...] Read more.

To meet the demands for heightened detection sensitivity in satellite-based space target detection systems, we introduce an innovative square aperture diaphragm system utilizing freeform surfaces for detecting targets in the visible light spectrum. Characterized by a 40 mm × 40 mm square entrance pupil, a 4° × 4° field of view (FOV), and a 150 mm focal length, this system achieves a spot size of 2 × 2 pixels with 85% energy concentration within 18.4 μm, showcasing exceptional performance. Our design, compared to a circular aperture system of similar specifications, increases the entrance pupil area by 27% while having a smaller volume, resulting in a 0.24 magnitude improvement in the detection of space targets. This advancement significantly enhances our ability to detect fainter space targets with high sensitivity. The findings of this study pave the way for advancements in satellite-based space target detection technology. Full article

► Show Figures

Figure 1

12 pages, 28322 KiB

Open AccessArticle

Optimization of Erbium-Doped Fiber to Improve Temperature Stability and Efficiency of ASE Sources

by Jia Guo, Hao Zhang, Wenbin Lin and Wei Xu

Photonics 2025, 12(2), 115; https://doi.org/10.3390/photonics12020115 - 27 Jan 2025

Viewed by 399

Abstract

The ASE (Amplified Spontaneous Emission) light source, based on erbium-doped fiber (EDF), is a broadband light source with advantages such as high power, excellent temperature stability, and low coherent light generation. It is widely used in the field of fiber optic sensing. However, [...] Read more.

The ASE (Amplified Spontaneous Emission) light source, based on erbium-doped fiber (EDF), is a broadband light source with advantages such as high power, excellent temperature stability, and low coherent light generation. It is widely used in the field of fiber optic sensing. However, traditional ASE sources suffer from temperature sensitivity and low efficiency, which can compromise the accuracy and stability of the output light’s average wavelength. This study focuses on optimizing the erbium-doped fiber (EDF) to improve the temperature stability and efficiency of the ASE light source. Through simulations, we found that the appropriate doping concentration and length of the EDF are key factors in enhancing the stability and efficiency of the ASE source. Inorganic metal chloride vapor-phase doping combined with an improved chemical vapor deposition process was used to fabricate the erbium-doped fiber, ensuring low background loss, minimal OH⁻ absorption, and uniform distribution of the erbium ions in the core of the fiber. The optimized EDFs were integrated into the ASE source, achieving a power conversion efficiency of 53.6% and a temperature stability of 0.118 ppm/°C within the temperature range of −50 °C to 70 °C. This study offers a practical approach for improving the performance of ASE light sources and advancing the development of high-precision fiber optic sensing technologies. Full article

(This article belongs to the Special Issue Novel Two-Dimensional Materials Based on Nonlinear Photonics)

► Show Figures

Figure 1

12 pages, 1458 KiB

Open AccessArticle

Correlated Photon Lidar Based on Time-Division Multiplexing

by Yun Jiang, Bo Liu, Zixun Wang, Fengyun Huang, Taibei Liu, Lan Luo, Feifan He, Yongqi Yang and Bin Zhao

Photonics 2025, 12(2), 114; https://doi.org/10.3390/photonics12020114 - 27 Jan 2025

Viewed by 345

Abstract

Single-photon lidar (SPL) exhibits high sensitivity, making it particularly suitable for detecting weak echoes over long distances. However, its susceptibility to background noise necessitates the implementation of advanced filtering techniques and complex algorithms, which can significantly increase system cost and complexity. To address [...] Read more.

Single-photon lidar (SPL) exhibits high sensitivity, making it particularly suitable for detecting weak echoes over long distances. However, its susceptibility to background noise necessitates the implementation of advanced filtering techniques and complex algorithms, which can significantly increase system cost and complexity. To address these challenges, we propose a time-division-multiplexing-based correlated photon lidar system that employs a narrowband pulsed laser with stable time delays and variable pulse intensities, thereby establishing temporal and intensity correlations. This all-fiber solution not only simplifies the system architecture but also enhances operational efficiency. An adaptive cross-correlation method incorporating time slicing has been developed to extract histogram signals, enabling successful 1.5 km distance measurements under intense daytime noise conditions, using a 1 s accumulation time and a 20 mm receiving aperture. The experimental results demonstrate a 38% (from 1.11 to 1.52) improvement in the signal-to-noise ratio (SNR), thereby enhancing the system’s anti-noise capability, facilitating rapid detection, and reducing overall system costs. Full article

► Show Figures

Figure 1

30 pages, 12023 KiB

Open AccessArticle

Three-Dimensional Scalar Time-Dependent Photorefractive Beam Propagation Model

by Mark Cronin-Golomb

Photonics 2025, 12(2), 113; https://doi.org/10.3390/photonics12020113 - 27 Jan 2025

Viewed by 438

Abstract

This paper presents an open-source time-dependent three-dimensional scalar photorefractive beam propagation model (PRProp3D) based on the well-known split-step method. The angular spectrum method is used for the diffractive steps, and the nonlinearities accumulated at the end of each diffractive step are applied using [...] Read more.

This paper presents an open-source time-dependent three-dimensional scalar photorefractive beam propagation model (PRProp3D) based on the well-known split-step method. The angular spectrum method is used for the diffractive steps, and the nonlinearities accumulated at the end of each diffractive step are applied using spatially varying phase screens. Comparisons with previously published experimental results are given for image amplification, photorefractive amplified scattering (fanning) and photorefractive screening solitons. Artifacts can be mitigated by use of step sizes less than 5~10 micrometers and by careful choice of the transverse computation grid size to ensure adequate sampling. Wraparound effects associated with the use of discrete Fourier transforms are mitigated by apodization and beam centering. Full article

(This article belongs to the Section Optoelectronics and Optical Materials)

► Show Figures

Figure 1

13 pages, 2913 KiB

Open AccessArticle

An Optical Differential Method for Underwater Wireless Communication in Turbid Environments

by Xiaoqing Tian, Feng Jiang, Hongfei Yu, Hang Xu and Jiyong Wang

Photonics 2025, 12(2), 112; https://doi.org/10.3390/photonics12020112 - 27 Jan 2025

Viewed by 445

Abstract

Underwater optical communication has emerged as an essential tool for exploring oceanography and marine resources for underwater vehicles or robots in recent years. Current techniques mostly rely on the paradigm of intensity modulation and direct detection, resorting to more powerful light sources on [...] Read more.

Underwater optical communication has emerged as an essential tool for exploring oceanography and marine resources for underwater vehicles or robots in recent years. Current techniques mostly rely on the paradigm of intensity modulation and direct detection, resorting to more powerful light sources on the transmitting side and more sensitive detectors on the receiving side, thus causing excess energy consumption and system costs. Here, a novel approach, namely, the optical differential communications method (ODCM), is proposed to extend the distance of underwater wireless optical communications in turbid water. The underlying physical reason is explained in theory and demonstrated in experiments. It is found that the stable propagation distance of ODCM could be further extended without relying on intensive light sources, in contrast to conventional methods, showing potential for longer communication ranges. Tests of underwater optical communications are conducted, and the results show that ODCM can significantly reduce the bit error rate (BER) at the same propagation distance or extend the propagation distance for the same BER level of optical signals. As such, this study provides an avenue for long-distance and stable underwater wireless optical communications in turbid environments. Full article

(This article belongs to the Special Issue Challenges and Opportunities in Underwater Wireless Optical Communications)

► Show Figures

Figure 1

11 pages, 2094 KiB

Open AccessArticle

Highly Efficient Polarization-Insensitive Grating Couplers on Thin-Film Lithium Niobate with an Integrated Gold Layer

by Alaa Sultan, Mostafa Khalil, Leila Mehravar and Chang-qing Xu

Photonics 2025, 12(2), 111; https://doi.org/10.3390/photonics12020111 - 27 Jan 2025

Viewed by 438

Abstract

The thin-film lithium niobate platform, which is emerging as a promising photonic integration platform, currently lacks a polarization-insensitive grating coupler (GC), a crucial component for polarization-independent fiber interfaces. This limitation restricts its use in many applications, such as polarization-insensitive modulation systems and polarization [...] Read more.

The thin-film lithium niobate platform, which is emerging as a promising photonic integration platform, currently lacks a polarization-insensitive grating coupler (GC), a crucial component for polarization-independent fiber interfaces. This limitation restricts its use in many applications, such as polarization-insensitive modulation systems and polarization management. In this study, we propose a polarization-insensitive nonuniform GC, achieved by intersecting optimal TE- and TM-mode grating periods. Based on our simulation results, the proposed design delivers a coupling efficiency (CE) of 80% for TE and 78.5% for TM polarization, with a polarization-dependent loss of less than 0.14 dB at a wavelength of 1550 nm. The inserted gold layer, i.e., that inside the substrate layer, boosts the CEs of the optimal TE- and TM-mode GC by about 50%, resulting in a highly efficient, polarization-insensitive solution. This advancement enables on-chip polarization diversity applications on the thin-film lithium niobate platform. We also investigate the fabrication and alignment tolerances of the proposed design to ensure robust performance under practical conditions. Full article

(This article belongs to the Special Issue Advanced Photonic Integration Technology and Devices)

► Show Figures

Figure 1

10 pages, 7692 KiB

Open AccessArticle

Array-Patterned Micro-Structures in Spectacle Lenses Designed for Myopia Control via Image Blur

by Huilv Jiang, Zengwei Zhao, Quan Yuan, Yiqian Li, Ke Ma, Yaoyao Fu, Jiaojie Chen, Jun Jiang and Yiyu Li

Photonics 2025, 12(2), 110; https://doi.org/10.3390/photonics12020110 - 26 Jan 2025

Viewed by 465

Abstract

Using micro-structure components in spectacle lenses has enabled myopia progression control in children and teenagers. However, the optical design of these spectacle lenses has never been discussed, leading to a lack of correct understanding of the underlying optical treatment principles. In this work, [...] Read more.

Using micro-structure components in spectacle lenses has enabled myopia progression control in children and teenagers. However, the optical design of these spectacle lenses has never been discussed, leading to a lack of correct understanding of the underlying optical treatment principles. In this work, array-patterned hexagonal lenslets with two powers of opposite signs were proposed to construct a lenslet array-integrated (LARI) spectacle lens developed for an ongoing, randomized, controlled clinical trial and to support the optical approach to myopia control leveraging retinal image blur. We found that the phase modulation induced by the micro-structures of the lenslet array contributes to the increase in RMS wavefront aberrations, leading to image blur, further inspiring the novel array-patterned micro-structure design with high-order phase elements (HOPEs). The optical performance of both LARI and HOPE spectacle lenses was investigated by simulation and experiment. Full article

(This article belongs to the Special Issue Advances in Visual Optics)

► Show Figures

Figure 1

12 pages, 2018 KiB

Open AccessArticle

Terahertz Multicolor Imaging of Opaque Objects Using Self-Mixing Interferometry with Quantum-Cascade Lasers

by Jiaxuan Cai, Yan Xie, Yingxin Wang, Meng Chen, Lianhe Li, Mohammed Salih, Edmund H. Linfield, Ning Yang, Weidong Chu, Peng Bai and Ziran Zhao

Photonics 2025, 12(2), 109; https://doi.org/10.3390/photonics12020109 - 25 Jan 2025

Viewed by 447

Abstract

Self-mixing interference in a terahertz quantum-cascade laser has been demonstrated to be suitable for the detection of weak signals scattered or reflected by the target. This technology has achieved the high-sensitivity detection of complex refractive indices, surface/interface morphologies and molecular feature spectra. Here, [...] Read more.

Self-mixing interference in a terahertz quantum-cascade laser has been demonstrated to be suitable for the detection of weak signals scattered or reflected by the target. This technology has achieved the high-sensitivity detection of complex refractive indices, surface/interface morphologies and molecular feature spectra. Here, a set of terahertz quantum-cascade lasers with different lasing frequencies is used to inspect a tiny amount of powder concealed inside a polytetrafluoroethylene tablet by using self-mixing interferometry combined with the penetration properties of terahertz waves. Multicolor spectral images were acquired, which were synthesized by absorption contrast images obtained at different lasing frequencies. They enable the detection of the spatial distribution of hidden objects which are totally opaque in visual light and allow for them to be identified with spectral absorption characteristics. Self-mixing interference technology can also obtain phase information when a terahertz wave interacts with a tablet, showing the difference between the hidden object and surroundings from another dimension. Our research may provide a strategy for the development of terahertz multispectral imaging technology for the inspection of hidden trace residues. Full article

(This article belongs to the Section New Applications Enabled by Photonics Technologies and Systems)

► Show Figures

Figure 1

18 pages, 5909 KiB

Open AccessCommunication

High-Speed Target Location Based on Photoelectric Imaging and Laser Ranging with Fast Steering Mirror Deflection

by Kui Shi, Hongtao Yang, Jianwei Peng, Yingjun Ma and Hongwei Zhang

Photonics 2025, 12(2), 108; https://doi.org/10.3390/photonics12020108 - 24 Jan 2025

Viewed by 521

Abstract

There is an increasing number of spacecrafts in orbit, and the collision impact of high-speed moving targets, such as space debris, can cause fatal damage to these spacecrafts. It has become increasingly important to rapidly and accurately locate high-speed moving targets in space. [...] Read more.

There is an increasing number of spacecrafts in orbit, and the collision impact of high-speed moving targets, such as space debris, can cause fatal damage to these spacecrafts. It has become increasingly important to rapidly and accurately locate high-speed moving targets in space. In this study, we designed a visible-light telephoto camera for observing high-speed moving targets and a laser rangefinder for measuring the precise distance of these targets, and we proposed a method of using fast steering mirror deflection to quickly direct the emitted laser towards such targets and measure the distance. Based on the principle of photographic imaging and the precise distance of targets, a collinear equation and a spatial target location model based on the internal and external orientation elements of the camera and the target distance were established, and the principle of target location and the method for calculating target point coordinates were determined. We analyzed the composition of target point location error and derived an equation for calculating such errors. Based on the actual values of various error components and the error synthesis theory, the accuracy of target location was calculated to be 26.5 m when the target distance is 30 km (the relative velocity is 8 km/s and the velocity component perpendicular to the camera’s optical axis is less than 3.75 km/s). This study provides a theoretical basis and a method for solving the practical needs of quickly locating high-speed moving targets in space and proposes specific measures to improve target location accuracy. Full article

(This article belongs to the Special Issue Optical Technology for Challenging Conditions：Methods and Applications)

► Show Figures

Figure 1

16 pages, 8742 KiB

Open AccessArticle

Design of Off-Axis Four-Mirror Optical Systems Enabled by Freeform Optics

by Jiadong Yu and Xianglong Mao

Photonics 2025, 12(2), 107; https://doi.org/10.3390/photonics12020107 - 24 Jan 2025

Viewed by 349

Abstract

The off-axis reflective optical system offers several advantages, including the elimination of central obstruction, zero chromatic aberration, and a compact structure. These features make it highly valuable in the domain of space remote sensing. Freeform surfaces transcend the limitations imposed by rotational symmetry, [...] Read more.

The off-axis reflective optical system offers several advantages, including the elimination of central obstruction, zero chromatic aberration, and a compact structure. These features make it highly valuable in the domain of space remote sensing. Freeform surfaces transcend the limitations imposed by rotational symmetry, providing significant design flexibility that is particularly effective for correcting non-rotationally symmetric aberrations present in off-axis systems. In this paper, we propose the averaged seed curve extension (A-SCE) method, which facilitates the direct design of an initial structure for freeform off-axis reflective systems. Both focal and afocal off-axis four-mirror freeform optical systems are designed utilizing the A-SCE method, demonstrating an enhanced capability for initial structure design. The results indicate excellent optical performance while maintaining relatively loose processing and assembly tolerances for both systems, thereby enhancing the facilitation of practical implementation. Full article

13 pages, 3141 KiB

Open AccessArticle

Improved Performances in Point-to-Multipoint Flexible Optical Transceivers Utilizing Cascaded Discrete Fourier Transform-Spread Inverse Fast Fourier Transform/Fast Fourier Transform-Based Multi-Channel Aggregation/De-Aggregation

by Lin Chen, Yingxue Gao, Wei Jin, Han Yang, Shenming Jiang, Shu Liu, Yi Huang and Jianming Tang

Photonics 2025, 12(2), 106; https://doi.org/10.3390/photonics12020106 - 24 Jan 2025

Viewed by 412

Abstract

The previously proposed cascaded inverse fast Fourier transform/fast Fourier transform (IFFT/FFT)-based point-to-multipoint (P2MP) flexible optical transceivers have the potential to equip future intensity modulation and direct detection (IMDD) optical access networks with excellent flexibility, adaptability, scalability and upgradability. However, due to their cascaded [...] Read more.

The previously proposed cascaded inverse fast Fourier transform/fast Fourier transform (IFFT/FFT)-based point-to-multipoint (P2MP) flexible optical transceivers have the potential to equip future intensity modulation and direct detection (IMDD) optical access networks with excellent flexibility, adaptability, scalability and upgradability. However, due to their cascaded IFFT-based multi-channel aggregations, P2MP flexible transceivers suffer high peak-to-average power ratios (PAPRs). To address the technical challenge, this paper proposes a novel P2MP flexible optical transceiver, which uses a cascaded discrete Fourier transformation-spread (DFT-Spread) IFFT/FFT-based multi-channel aggregation/de-aggregation and standard signal clipping to jointly reduce its PAPRs. The upstream performances of the proposed transceivers are numerically explored in a 20 km IMDD upstream passive optical network (PON). The results indicate that the proposed transceiver’s PAPRs are mainly dominated by the size of the last IFFT operation of the multi-channel aggregation, and are almost independent of modulation format and channel count. Compared to conventional cascaded IFFT/FFT-based P2MP transceivers with and without clipping operations, the proposed DFT-Spread P2MP transceivers can reduce PAPRs by 2.6 dB and 3.5 dB, respectively, for a final IFFT operation size of 1024. More significant PAPR reductions are achievable when the last IFFT operation size is increased further. As a direct result, compared to conventional P2MP transceivers adopting clipping operations only, the proposed transceiver can improve upstream receiver sensitivities by >1.9 dB and the aggregated upstream transmission capacities by >14.1%. Such aggregated upstream transmission capacity enhancements are independent of channel count and become more pronounced for longer transmission distances. Full article

(This article belongs to the Section Optical Communication and Network)

► Show Figures

Figure 1

18 pages, 9376 KiB

Open AccessArticle

Spatial Goos–Hänchen Shifts of Airy Vortex Beams Impinging on Graphene/hBN Heterostructure

by Xiaojin Yang, Tan Qu, Zhengjun Li and Zhensen Wu

Photonics 2025, 12(2), 105; https://doi.org/10.3390/photonics12020105 - 24 Jan 2025

Viewed by 383

Abstract

Based on the angular spectrum expansion, the spatial Goos–Hänchen (GH) shift of an Airy vortex beam reflected from the graphene/hexagonal boron nitride (hBN) heterostructure is investigated analytically. The influences of graphene/hBN heterostructure parameters and incident Airy vortex beam parameters on the spatial GH [...] Read more.

Based on the angular spectrum expansion, the spatial Goos–Hänchen (GH) shift of an Airy vortex beam reflected from the graphene/hexagonal boron nitride (hBN) heterostructure is investigated analytically. The influences of graphene/hBN heterostructure parameters and incident Airy vortex beam parameters on the spatial GH shifts are analyzed in detail. It is found that the position of the Brewster angle mainly depends on the relaxation time and hBN thickness of the heterostructure, and the magnitude and sign of GH shifts at a certain Brewster angle can be controlled effectively by tuning the Fermi energy and layer numbers of graphene. Moreover, the variation in the GH shifts with the Fermi energy and hBN thickness exhibits hyperbolicity at the Brewster angle, similar to the variation in the permittivity of hBN. For the incident beam, the vortex position and the decay factor in the x direction have a great effect on the GH shifts. The influence of the vortex position on the GH shift is related to the distance of the vortex position from the origin point. The magnitude of the GH shift decreases as the decay factor in the x direction increases, and a large GH shift can be obtained by adjusting the decay factor in the x direction. Finally, the application of spatial GH shift in sensing is discussed. The results presented here may provide some supports to the design of optical switch and optical sensor. Full article

► Show Figures

Figure 1

15 pages, 4966 KiB

Open AccessArticle

Wavelength-Dependent Calcium Signaling Response to Photobiomodulation in Pancreatic Cells

by Kelli Fowlds, Anne M. Alsup, Abhidha Kunwar, Carly M. Darden, Jacob M. Luber, Michael C. Lawrence and Michael Cho

Photonics 2025, 12(2), 99; https://doi.org/10.3390/photonics12020099 - 23 Jan 2025

Viewed by 565

Abstract

Diabetes mellitus is a metabolic disorder that is rapidly growing across the world. Our laboratory has recently demonstrated that photobiomodulation (PBM) can couple to its metabolic pathways by modulating calcium dynamics in islet cells, including α- and β-cells. Using computer vision algorithms, changes [...] Read more.

Diabetes mellitus is a metabolic disorder that is rapidly growing across the world. Our laboratory has recently demonstrated that photobiomodulation (PBM) can couple to its metabolic pathways by modulating calcium dynamics in islet cells, including α- and β-cells. Using computer vision algorithms, changes in PBM-induced calcium dynamics can be verified, and, more importantly, this led us to propose hypotheses that will likely advance our understanding of photostimulatory effects in islet cells. In our previous paper, we determined changes in calcium spiking in response to PBM at 810 nm by manually segmenting the cells and the calcium spiking patterns. We have since developed a computer vison pipeline to automate cell segmentation and subsequent image analyses. By using automated methods for segmentation, registration, tracking, and statistical analysis, we were able to improve the accuracy of previously observed changes in calcium spiking in response to PBM in both cell types. Moreover, this pipeline was applied to elucidate the wavelength-dependent modulation of calcium dynamics at 1064 nm. The extent of increase in calcium spiking appears to have been overestimated by manual analysis, and the machine learning pipeline was able to capture and segment nearly 3-fold more cells, suggesting improved accuracy in the analysis of calcium spiking in islet cells. Detailed calcium analysis also indicates a biphasic dose response among α- and β-cells in response to PBM therapy at different wavelengths. The current findings offer a novel hypothesis and may facilitate the use of translational PBM as a potential therapy for diabetes mellitus. Full article

(This article belongs to the Special Issue Phototheranostics: Science and Applications)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Photonics, Volume 12, Issue 2 (February 2025) – 41 articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI